All AR9003 devices are PCI-E only, the extra delay here
is not required and only reduces the delay for loading
the initial register values by at least 14ms.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 has been tested with the new ANI implementation
and so ANI can now be enabled for that family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ANI implementation will use this to skip ANI
calibration upon a scan. This cannot be ported to the
older ANI implementation unless default ANI values from
the ANI are also used upon a scan. This is essentially
what one of the things thenew ANI does.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get an MIB interrupt when we hit certain PHY error counter
thresholds. If ANI is disabled but the MIB interrupt is enabled
we'll keep around the old MIB interrupt causes.
Since ath9k disables the MIB interrupt when ANI is disabled
this is not a fix, but more of a sanity fix in case we ever
need the MIB interrupt enabled but disabling ANI.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The clock rate was assumed to be static but it actually
changes depending on the mode of operation, correct this
to help improve the calcuation of the listenTime for ANI.
This change will help adjust ANI more accurately on different
PHY thresholds.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used by the ANI code next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath5k_hw_set_antenna_mode() always writes the default antenna register
and is called at the end of reset, there is no need to separately save and
restore the default antenna.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Collect all pieces concering the antenna switch table into one function.
Previously it was split up between ath5k_hw_reset() and
ath5k_hw_commit_eeprom_settings().
Also we need to set the antenna switch table when ath5k_hw_set_antenna_mode()
is called manually (by "iw phy0 antenna set", for example).
I'm not sure if we need to set the switchtable at the same place in
ath5k_hw_reset() as it was before - it is set later thru
ath5k_hw_set_antenna_mode() anyways - but i leave it there to avoid
problems(?).
Plus print switchtable registers in the debugfs file.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
#define AR5K_PHY_RESTART_DIV_GC 0x001c0000
is 3 bit wide.
The previous values of 0xc and 0x8 are 4bit wide and bigger than the mask.
Writing 0 and 1 to AR5K_PHY_RESTART_DIV_GC is consistent with the comments and
initvals we have in the HAL.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes 'make -j24 CONFIG_DEBUG_SECTION_MISMATCH=y' warning:
drivers/net/wireless/ath/ath9k/eeprom_4k.c: In function ‘ath9k_hw_get_4k_gain_boundaries_pdadcs.clone.1’:
drivers/net/wireless/ath/ath9k/eeprom_4k.c:311: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_9287.c: In function ‘ath9k_hw_get_AR9287_gain_boundaries_pdadcs’:
drivers/net/wireless/ath/ath9k/eeprom_9287.c:302: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function ‘ath9k_hw_get_def_gain_boundaries_pdadcs.clone.0’:
drivers/net/wireless/ath/ath9k/eeprom_def.c:679: error: ‘minPwrT4’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the channel is not set yet and we configure the antennas just store the
setting. It will be activated during the next reset, when the channel is set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit added an entry in 11na and 11ng rate
table but missed to update its rate count field. This
inconsistency between the rate count and the actual number
of rates in the table will leave out the final rate entry
(mcs15 with half gi in ht40) while forming the valid
rate indices. Not having mcs15+shortGI in ht40 will have
a performance impact (on max throughput) of about 10% both
in nght40 and naht40 mode.
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu May 13 18:42:38 2010 -0700
ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-AR9271 chips, the credit size is different
and has to be configured appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR7010 is dual-band. Setup the channels and rateset
for 5GHz band.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate information on the target has to be updated
for 2-stream devices, along with the correct chainmask.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The supported MCS rate set has to be setup properly
for 2-stream devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB device IDs for AR7010 and handle
firmware loading properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes programming the byte swap registers
for chipsets other than AR9271. This is needed for
AR7010.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not assign the FW name to driver_info but determine
it dynamically on device probe. This facilitates adding new
firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Cc: stable@kernel.org
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building a kernel with CONFIG_PM=y but neither suspend nor
hibernate support, the compiler complains about the static functions
ath5k_pci_suspend() and ath5k_pci_resume() not being used:
drivers/net/wireless/ath/ath5k/base.c:713:12: warning: ‘ath5k_pci_suspend’ defined but not used
drivers/net/wireless/ath/ath5k/base.c:722:12: warning: ‘ath5k_pci_resume’ defined but not used
Depending on CONFIG_PM_SLEEP rather than CONFIG_PM fixes the issue.
Signed-off-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_add/sta_remove are the callbacks that can sleep.
Use them instead of sta_notify.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If buffer is to be accessed by cpu after dma is over, but
between dma mapping and dma unmapping, we should use
dma_sync_single_for_cpu to sync the buffer between cpu with
device. And dma_sync_single_for_device is used to let
device gain the buffer again.
v2: Felix pointed out dma_sync_single_for_device is needed to return
buffer to device if an unsuccessful status bit check is found.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because there is a limited number of tx buffers available, once the
queue has been filled to a certain point, ath9k needs to stop accepting
new frames from mac80211. In order to prevent a full WMM queue from
stopping another queue with fewer frames, this patch limits the number
of queued frames to a quarter of the total available tx buffers, minus
some reserved frames to be used for other purposes (e.g. beacons).
Because tx buffers are reserved for frames when they're staged in
software queues as well, the actual queue depth cannot be used for
this, so this patch stores a reference to the tx queue in the ath_buf
struct and keeps track of the total number of pending frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes beacon distribution in IBSS mode
by configuring the hardware beacon queue properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters used by ANI have to be disabled
on the host because the FW doesn't do it on the target side.
Also, flush the receive buffers before initializing
RX on the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The monitor interface instance on the target has
to be removed before setting it to FULLSLEEP.
Handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ps_idle is protected by the htc_pm_lock mutex.
Use it to protect the variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to cancel the PS work when disassociation
happens. The work handlers are cancelled in the stop()
callback.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the radio only when mac80211 indicates it,
through the IEEE80211_CONF_CHANGE_IDLE flag.
Not handling this properly will result in multiple
calls to radio_disable() even though the radio is
already idle.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when registers are accessed.
Ensure this is so by using the PS wrappers at
appropriate places.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps IDLE power save handling in the driver.
Two separate functions (radio enable/disable) are introduced,
because the semantics of radio handling is just not the same
as the start()/stop() callbacks. For example, the HW must not
be disabled, instead, the PHY has to be disabled in radio_disable().
Also, the HW has to be reset properly in radio enable/disable and
certain registers have to be programmed only once, in the
start() callback.
The radio_enable() routine doesn't need the PS wrappers since
we set the HW power mode to AWAKE anyway before calling it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Async fifo is now enabled only for versions 1.3 and above.
Enable it in the appropriate place, in the reset routine,
instead of process_ini().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the PCI power save handling
code, fixing ASPM hangs and handling device state D3
properly.
The WAR register is programmed with the correct
values now.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a few comments, and move the updation of max_power_level
to a helper routine. This is also done by non-4K based chipsets,
this will be fixed in a separate patch.
* Remove two WARs which are required for old AR5416 chipsets,
and are not needed for AR9287.
* Fix indentation and make things readable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than doing a series of RMWs, calculate the
value to be written to the register in question and
do a single REGWRITE. This improves bringup time.
This depends on the analog_shiftreg configuration option,
which is currently buggy. For AP mode, a delay of 100us
has to be the default. For station mode, this knob has to
be enabled on a per-case basis, though it is a little
unclear on when to enable a delay. This can be fixed later though.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix whitespace damage.
* Remove unused debug messages.
* Introduce a macro NUM_EEP_WORDS.
* Convert AR9287 to lowercase in function names.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the buggy 'ath9k: Group Key fix for VAPs' change.
For AP mode group keys, use the BSSID as lookup mac address, with
the multicast keysearch bit set.
For IBSS mode, use the peer's MAC address with multicast keysearch.
For STA mode, keep using the group key slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
