The documentation for syscall_get_nr() in asm-generic says:
Note this returns int even on 64-bit machines. Only 32 bits of
system call number can be meaningful. If the actual arch value
is 64 bits, this truncates to 32 bits so 0xffffffff means -1.
However our implementation was never updated to reflect this.
Generally it's not important, but there is once case where it matters.
For seccomp filter with SECCOMP_RET_TRACE, the tracer will set
regs->gpr[0] to -1 to reject the syscall. When the task is a compat
task, this means we end up with 0xffffffff in r0 because ptrace will
zero extend the 32-bit value.
If syscall_get_nr() returns an unsigned long, then a 64-bit kernel will
see a positive value in r0 and will incorrectly allow the syscall
through seccomp.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Currently syscall_get_arguments() is used by syscall tracepoints, and
collect_syscall() which is used in some debugging as well as
/proc/pid/syscall.
The current implementation just copies regs->gpr[3 .. 5] out, which is
fine for all the current use cases.
When we enable seccomp filter, that will also start using
syscall_get_arguments(). However for seccomp filter we want to use r3
as the return value of the syscall, and orig_gpr3 as the first
parameter. This will allow seccomp to modify the return value in r3.
To support this we need to modify syscall_get_arguments() to return
orig_gpr3 instead of r3. This is safe for all uses because orig_gpr3
always contains the r3 value that was passed to the syscall. We store it
in the syscall entry path and never modify it.
Update syscall_set_arguments() while we're here, even though it's never
used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Currently syscall_get_arguments() has two loops, one for compat and one
for regular tasks. In prepartion for the next patch, which changes which
registers we use, switch it to only have one loop, so we only have one
place to update.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Currently the only caller of syscall_set_return_value() is seccomp
filter, which is not enabled on powerpc.
This means we have not noticed that our implementation of
syscall_set_return_value() negates error, even though the value passed
in is already negative.
So remove the negation in syscall_set_return_value(), and expect the
caller to do it like all other implementations do.
Also add a comment about the ccr handling.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
syscall_get_error() is unused, and never has been.
It's also probably wrong, as it negates r3 before returning it, but that
depends on what the caller is expecting.
It also doesn't deal with compat, and doesn't deal with TIF_NOERROR.
Although we could fix those, until it has a caller and it's clear what
semantics the caller wants it's just untested code. So drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Since both ppc and ppc64 have LE variants which are now reported by uname, add
that flag (__AUDIT_ARCH_LE) to syscall_get_arch() and add AUDIT_ARCH_PPC64LE
variant.
Without this, perf trace and auditctl fail.
Mainline kernel reports ppc64le (per a058801) but there is no matching
AUDIT_ARCH_PPC64LE.
Since 32-bit PPC LE is not supported by audit, don't advertise it in
AUDIT_ARCH_PPC* variants.
See:
https://www.redhat.com/archives/linux-audit/2014-August/msg00082.htmlhttps://www.redhat.com/archives/linux-audit/2014-December/msg00004.html
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull more powerpc updates from Michael Ellerman:
"Here's some more updates for powerpc for 3.18.
They are a bit late I know, though must are actually bug fixes. In my
defence I nearly cut the top of my finger off last weekend in a
gruesome bike maintenance accident, so I spent a good part of the week
waiting around for doctors. True story, I can send photos if you like :)
Probably the most interesting fix is the sys_call_table one, which
enables syscall tracing for powerpc. There's a fix for HMI handling
for old firmware, more endian fixes for firmware interfaces, more EEH
fixes, Anton fixed our routine that gets the current stack pointer,
and a few other misc bits"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (22 commits)
powerpc: Only do dynamic DMA zone limits on platforms that need it
powerpc: sync pseries_le_defconfig with pseries_defconfig
powerpc: Add printk levels to setup_system output
powerpc/vphn: NUMA node code expects big-endian
powerpc/msi: Use WARN_ON() in msi bitmap selftests
powerpc/msi: Fix the msi bitmap alignment tests
powerpc/eeh: Block CFG upon frozen Shiner adapter
powerpc/eeh: Don't collect logs on PE with blocked config space
powerpc/eeh: Block PCI config access upon frozen PE
powerpc/pseries: Drop config requests in EEH accessors
powerpc/powernv: Drop config requests in EEH accessors
powerpc/eeh: Rename flag EEH_PE_RESET to EEH_PE_CFG_BLOCKED
powerpc/eeh: Fix condition for isolated state
powerpc/pseries: Make CPU hotplug path endian safe
powerpc/pseries: Use dump_stack instead of show_stack
powerpc: Rename __get_SP() to current_stack_pointer()
powerpc: Reimplement __get_SP() as a function not a define
powerpc/numa: Add ability to disable and debug topology updates
powerpc/numa: check error return from proc_create
powerpc/powernv: Fallback to old HMI handling behavior for old firmware
...
Declaring sys_call_table as a pointer causes the compiler to generate
the wrong lookup code in arch_syscall_addr().
<arch_syscall_addr>:
lis r9,-16384
rlwinm r3,r3,2,0,29
- lwz r11,30640(r9)
- lwzx r3,r11,r3
+ addi r9,r9,30640
+ lwzx r3,r9,r3
blr
The actual sys_call_table symbol, declared in assembler, is an
array. If we lie about that to the compiler we get the wrong code
generated, as above.
This definition seems only to be used by the syscall tracing code in
kernel/trace/trace_syscalls.c. With this patch I can successfully use
the syscall tracepoints:
bash-3815 [002] .... 333.239082: sys_write -> 0x2
bash-3815 [002] .... 333.239087: sys_dup2(oldfd: a, newfd: 1)
bash-3815 [002] .... 333.239088: sys_dup2 -> 0x1
bash-3815 [002] .... 333.239092: sys_fcntl(fd: a, cmd: 1, arg: 0)
bash-3815 [002] .... 333.239093: sys_fcntl -> 0x1
bash-3815 [002] .... 333.239094: sys_close(fd: a)
bash-3815 [002] .... 333.239094: sys_close -> 0x0
Signed-off-by: Romeo Cane <romeo.cane.ext@coriant.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Include linux/thread_info.h so we can use is_32_bit_task() cleanly.
Then just simplify syscall_get_arch() since is_32_bit_task() works for
all configuration options.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch implements the raw syscall tracepoints on PowerPC and exports
them for ftrace syscalls to use.
To minimise reworking existing code, I slightly re-ordered the thread
info flags such that the new TIF_SYSCALL_TRACEPOINT bit would still fit
within the 16 bits of the andi. instruction's UI field. The instructions
in question are in /arch/powerpc/kernel/entry_{32,64}.S to and the
_TIF_SYSCALL_T_OR_A with the thread flags to see if system call tracing
is enabled.
In the case of 64bit PowerPC, arch_syscall_addr and
arch_syscall_match_sym_name are overridden to allow ftrace syscalls to
work given the unusual system call table structure and symbol names that
start with a period.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc implementations of syscall_get_error and
syscall_set_return_value should use CCR0:S0 (0x10000000) for testing
and setting syscall error status. Fortunately these APIs don't seem
to be used at the moment.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
