According to the latest revision of the datasheet, the LVDS I/O pins
must be enabled before starting the PLL. Fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The VSL and HSL bits in the DSMR register set the corresponding
horizontal and vertical sync signal polarity to active high. The code
got it the wrong way around, fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
There is a bug in the setting of the DES (Display Enable Signal)
register. This current setting occurs 1 dot left shift. The DES
register should be set minus one value about the specifying value
with H/W specification. This patch corrects it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Dot clock routing is setup through different registers depending on the
DU generation. The code has been designed for Gen2 and hasn't been
updated since. This works thanks to good reset default value, but isn't
very safe. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Document the R8A7796-specific DT bindings and support them in the
driver. The HDMI output is currently not supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for the R8A7792 DU; it has 2 DPAD (RGB) outputs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
It isn't safe to call drm_dev_unregister() without first initializing
mode setting with drm_mode_config_init(). This leads to a crash if
either IO memory can't be remapped or vblank initialization fails.
Fix this by reordering the initialization sequence. Move vblank
initialization after the drm_mode_config_init() call, and move IO
remapping before drm_dev_alloc() to avoid the need to perform clean up
in case of failure.
While at it remove the explicit drm_vblank_cleanup() call from
rcar_du_remove() as the drm_dev_unregister() function already cleans up
vblank.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When an encoder fails to initialize the driver prints an error message
to the kernel log. The message contains the name of the encoder's DT
node, which is NULL for internal encoders. Use the of_node_full_name()
macro to avoid dereferencing a NULL pointer, print the output number to
add more context to the error, and make sure we still own a reference to
the encoder's DT node by delaying the of_node_put() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Memory allocation failures print messages to the kernel log, there's no
need to print an extra one. Remove the duplicate message.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The driver has lost platform data support a long time ago. R-Car DU
devices can only be instantiated through DT now, making it impossible to
have a NULL DT node pointer. Remove the error check.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Capitalize acronyms and use determiners and punctuation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The node passed as a pointer to the rcar_du_lvds_connector_init()
function is never modified, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
- better atomic state debugging from Rob
- fence prep from gustavo
- sumits flushed out his backlog of pending dma-buf/fence patches from
various people
- drm_mm leak debugging plus trying to appease Kconfig (Chris)
- a few misc things all over
* tag 'topic/drm-misc-2016-11-10' of git://anongit.freedesktop.org/drm-intel: (35 commits)
drm: Make DRM_DEBUG_MM depend on STACKTRACE_SUPPORT
drm/i915: Restrict DRM_DEBUG_MM automatic selection
drm: Restrict stackdepot usage to builtin drm.ko
drm/msm: module param to dump state on error irq
drm/msm/mdp5: add atomic_print_state support
drm/atomic: add debugfs file to dump out atomic state
drm/atomic: add new drm_debug bit to dump atomic state
drm: add helpers to go from plane state to drm_rect
drm: add helper for printing to log or seq_file
drm: helper macros to print composite types
reservation: revert "wait only with non-zero timeout specified (v3)" v2
drm/ttm: fix ttm_bo_wait
dma-buf/fence: revert "don't wait when specified timeout is zero" (v2)
dma-buf/fence: make timeout handling in fence_default_wait consistent (v2)
drm/amdgpu: add the interface of waiting multiple fences (v4)
dma-buf: return index of the first signaled fence (v2)
MAINTAINERS: update Sync File Framework files
dma-buf/sw_sync: put fence reference from the fence creation
dma-buf/sw_sync: mark sync_timeline_create() static
drm: Add stackdepot include for DRM_DEBUG_MM
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc4' into drm-next
Linux 4.9-rc4
This is needed for nouveau development.
We don't want all planes to be added to the state whenever a
plane with fixed zpos gets enabled/disabled. This is true
especially for eg. cursor planes on i915, as we want cursor
updates to go through w/o throttling. Same holds for drivers
that don't support zpos at all (i915 actually falls into this
category right now since we've not yet added zpos support).
Allow drivers more freedom by letting them deal with zpos
themselves instead of doing it in drm_atomic_helper_check_planes()
unconditionally. Let's just inline the required calls into all
the driver that currently depend on this.
v2: Inline the stuff into the drivers instead of adding another
helper, document things better (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: 44d1240d00 ("drm: add generic zpos property")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1476111056-12734-1-git-send-email-ville.syrjala@linux.intel.com
drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.
v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk
There are many reasons other than ENOMEM that drm_dev_init() can
fail. Return ERR_PTR rather than NULL to be able to distinguish
these in the caller.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160921145919.13754-2-teg@jklm.no
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
The conversion of the rcar-du driver from the I2C slave encoder to the
DRM bridge API left the HDMI encoder's bridge pointer NULL, preventing
the bridge from being handled automatically by the DRM core. Fix it.
Fixes: 1d926114d8 ("drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
version 6:
rebased patch on top rcar-du changes for zpos
version 4:
fix null pointer issue while setting zpos in plane reset function
This patch replaces zpos property handling custom code in rcar DRM
driver with calls to generic DRM code.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Suddenly everyone shows up with their trivial patch series!
- piles of if (!ptr) check removals from Markus Elfring
- more of_node_put fixes from Peter Chen
- make fbdev support really optional in all drivers (except vmwgfx),
somehow this fell through the cracks when we did all the hard prep work
a while ago. Patches from Tobias Jakobi.
- leftover patches for the connector reg/unreg cleanup (required that I
backmerged drm-next) from Chris
- last vgem fence patch from Chris
- fix up warnings in the new sphinx gpu docs build
- misc other small bits
* tag 'topic/drm-misc-2016-07-22' of git://anongit.freedesktop.org/drm-intel: (57 commits)
GPU-DRM-Exynos: Delete an unnecessary check before the function call "vunmap"
GPU-DRM-sun4i: Delete an unnecessary check before drm_fbdev_cma_hotplug_event()
drm/atomic: Delete an unnecessary check before drm_property_unreference_blob()
drm/rockchip: analogix_dp: add missing clk_disable_unprepare() on error
drm: drm_connector->s/connector_id/index/ for consistency
drm/virtio: Fix non static symbol warning
drm/arc: Remove redundant dev_err call in arcpgu_load()
drm/arc: Fix some sparse warnings
drm/vgem: Fix non static symbol warning
drm/doc: Spinx leftovers
drm/dp-mst: Missing kernel doc
drm/dp-mst: Remove tx_down_in_progress
drm/doc: Fix missing kerneldoc for drm_dp_helper.c
drm: Extract&Document drm_irq.h
drm/doc: document all the properties in drm_mode_config
drm/drm-kms.rst: Remove unused drm_fourcc.h include directive
drm/doc: Add kerneldoc for @index
drm: Unexport drm_connector_unregister_all()
drm/sun4i: Remove redundant call to drm_connector_unregister_all()
drm/ttm: Delete an unnecessary check before the function call "ttm_tt_destroy"
...
This is an update to the previous drm bridge pull request. The ADV7511
driver's conversion from slave encoder to bridge meant that its users
(the rcar-du kms driver) should use the bridge interface too. This pull
request now also contains a commit that updates the rcar-du's hdmi encoder
interface from slave encoder to bridge.
The other updates are as before:
- Converts the ADV7511 i2c slave encoder driver to a bridge driver.
Adds support for the ADV7533 bridge chip.
- Add bridge driver for TC358767 (DSI/DPI to eDP) encoder chips.
* 'drm_bridge_for_4.8' of https://github.com/boddob/linux:
drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder
drm/bridge: tc358767: Add DPI to eDP bridge driver
dt-bindings: tc358767: add DT documentation
dt-bindings: drm/bridge: Update bindings for ADV7533
drm/bridge: adv7533: Change number of DSI lanes dynamically
drm/bridge: adv7533: Use internal timing generator
drm/bridge: adv7533: Create a MIPI DSI device
drm/bridge: adv7533: Initial support for ADV7533
drm/bridge: adv7511: Fix mutex deadlock when interrupts are disabled
drm/i2c: adv7511: Move to bridge folder
drm/i2c: adv7511: Convert to drm_bridge
The hdmi output in rcar-du uses the i2c slave encoder interface to link
to the adv7511 encoder chip. The kms driver creates encoder and connector
entities that internally uses the drm_encoder_slave_funcs ops provided by
the slave encoder driver.
Change the driver such that it expects a bridge entity instead of a slave
encoder. The hdmi connector code isn't needed anymore as we expect the
adv7511 bridge driver to create/manage the connector.
Note that the kms driver still expects a connector node for hdmi to be
present in DT. This node has no connection to the connector created
by the bridge driver.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Currently enabling R-Car DRM support automatically pulls in
fbdev dependency. However this dep is unnecessary since
DRM core already handles this for us (DRM_FBDEV_EMULATION).
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
some rcar-du fixes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
drm: rcar-du: error message is not needed for EPROBE_DEFER
drm: rcar-du: error message is not needed for drm_vblank_init()
rcar-du: add/rename DEFR6 TCON bits
Since
commit e112e593b2
Author: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Date: Fri Dec 11 11:20:28 2015 +0100
drm: use dev_name as default unique name in drm_dev_alloc()
we're using a reasonable default which should work for everyone. Only
mtk, rcar-du and sun4i are affected, and as kms-only drivers without
any rendering support no one should ever care about the unique name
v2: Rebase on top of mediatek.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466499262-18717-5-git-send-email-daniel.vetter@ffwll.ch
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-8-git-send-email-chris@chris-wilson.co.uk
EPROBE_DEFER is not error, thus, error message on kernel log on this
case is confusable. Print it only error cases
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The only reason drm_vblank_init() could return an error at the
moment is a kcalloc() failure.
So we can remove current error message completely.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The TCNE2 bit of the DEFR6 register was renamed to TCNE1 in the R-Car gen2
manuals -- which makes more sense as that bit controls whether DU1, not DU2
is connected to TCON.
While at it, add the TCNE0 bit which controls whether DU0 is connected to
TCON.
Based on the large patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Make the Z-order of VSP planes configurable through the zpos property,
exactly as for the native DU planes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make the global alpha multiplier of VSP planes configurable through the
alpha property, exactly as for the native DU planes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All outputs have a 1:1 relationship between connectors and encoders,
and the driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementations and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-10-git-send-email-boris.brezillon@free-electrons.com
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
Ofc I promise just a few leftovers for drm-misc and somehow it's the
biggest pull. But really mostly trivial stuff:
- MAINTAINERS updates from Emil
- rename async to nonblock in atomic_commit to avoid the confusion between
nonblocking ioctl and async flip (= not vblank synced), from Maarten.
Needs to be regened with newer drivers, but probably only after -rc1 to
catch them all.
- actually lockless gem_object_free, plus acked driver conversion patches.
All the trickier prep stuff already is in drm-next.
- Noralf's nice work for generic defio support in our fbdev emulation.
Keeps the udl hack, and qxl is tested by Gerd.
* tag 'topic/drm-misc-2016-05-04' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm: Fixup locking WARN_ON mistake around gem_object_free_unlocked
drm/etnaviv: Use lockless gem BO free callback
drm/imx: Use lockless gem BO free callback
drm/radeon: Use lockless gem BO free callback
drm/amdgpu: Use lockless gem BO free callback
drm/gem: support BO freeing without dev->struct_mutex
MAINTAINERS: Add myself for the new VC4 (RPi GPU) graphics driver.
MAINTAINERS: Add a bunch of legacy (UMS) DRM drivers
MAINTAINERS: Add a few DRM drivers by Dave Airlie
MAINTAINERS: List the correct git repo for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Armada DRM driver
MAINTAINERS: Update the files list for the Rockchip DRM driver
MAINTAINERS: Update the files list for the Exynos DRM driver
MAINTAINERS: Add maintainer entry for the VMWGFX DRM driver
MAINTAINERS: Add maintainer entry for the MSM DRM driver
MAINTAINERS: Add maintainer entry for the Nouveau DRM driver
MAINTAINERS: Update the files list for the Etnaviv DRM driver
MAINTAINERS: Remove unneded wildcard for the i915 DRM driver
drm/atomic: Add WARN_ON when state->acquire_ctx is not set.
...
Commit d63c25e424 ("drm: rcar-du: Use generic
drm_connector_register_all() helper") left an unused local variable
behind. Remove it.
Fixes: d63c25e424 ("drm: rcar-du: Use generic drm_connector_register_all() helper")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The VSP1 compositor code in DRM links against the respective V4L
driver, but the dependency is not expressed correctly in Kconfig,
which leads to a build error when the DRM driver is built-in
and the V4L driver is a module:
drivers/gpu/built-in.o: In function `rcar_du_vsp_plane_atomic_update':
rcar-du/rcar_du_vsp.c:183: undefined reference to `vsp1_du_atomic_update'
This patch avoids the problem by ensuring that the DRM VSP code can
only be enabled if the V4L driver is linked into the kernel, or
both are loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6d62ef3ac3 ("drm: rcar-du: Expose the VSP1 compositor through KMS planes")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Now that a generic drm_connector_register_all() helper exists we may safely
substitute it for the driver-specific implementation of connectors plugging
in sysfs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1461068693-11260-4-git-send-email-abrodkin@synopsys.com
