If the PVT sensor is suddenly powered down while a caller is waiting for
the conversion completion, the request won't be finished and the task will
hang up on this procedure until the power is back up again. Let's call the
wait_for_completion_timeout() method instead to prevent that. The cached
timeout is exactly what we need to predict for how long conversion could
normally last.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920110924.19741-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of converting the update timeout data to the milliseconds each
time on the read procedure let's preserve the currently set timeout in the
dedicated driver private data cache. The cached value will be then used in
the timeout read method and in the alarm-less data conversion to prevent
the caller task hanging up in case if the PVT sensor is suddenly powered
down.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920110924.19741-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Baikal-T1 PVT sensor has got a dedicated power supply domain (feed up by
the external GPVT/VPVT_18 pins). In case if it isn't powered up, the
registers will be accessible, but the sensor conversion just won't happen.
Due to that an attempt to read data from any PVT sensor will cause the
task hanging up. For instance that will happen if XP11 jumper isn't
installed on the Baikal-T1-based BFK3.1 board. Let's at least test whether
the conversion work on the device probe procedure. By doing so will make
sure that the PVT sensor is powered up at least at boot time.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920110924.19741-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator support for boards where the sensor first need to be
powered up before it can be used.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Link: https://lore.kernel.org/r/20201001145738.17326-4-alban.bedel@aerq.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the documentation with the newly added features
* Set the accumulation interval based on resolution
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-5-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Factor out the common code in the accumulation functions for core and
socket accumulation.
While at it, handle the return value of the amd_create_sensor() function.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-4-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pinned pages are not properly accounted particularly when
mapping error occurs on IOTLB update. Clean up dangling
pinned pages for the error path. As the inflight pinned
pages, specifically for memory region that strides across
multiple chunks, would need more than one free page for
book keeping and accounting. For simplicity, pin pages
for all memory in the IOVA range in one go rather than
have multiple pin_user_pages calls to make up the entire
region. This way it's easier to track and account the
pages already mapped, particularly for clean-up in the
error path.
Fixes: 4c8cf31885 ("vhost: introduce vDPA-based backend")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601701330-16837-3-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the IOTLB device is enabled, the log_guest_addr that is passed by
userspace to the VHOST_SET_VRING_ADDR ioctl, and which is then written
to vq->log_addr, is a GIOVA. All writes to this address are translated
by log_user() to writes to an HVA, and then ultimately logged through
the corresponding GPAs in log_write_hva(). No logging will ever occur
with vq->log_addr in this case. It is thus wrong to pass vq->log_addr
and log_guest_addr to log_access_vq() which assumes they are actual
GPAs.
Introduce a new vq_log_used_access_ok() helper that only checks accesses
to the log for the used structure when there isn't an IOTLB device around.
Signed-off-by: Greg Kurz <groug@kaod.org>
Link: https://lore.kernel.org/r/160171933385.284610.10189082586063280867.stgit@bahia.lan
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the IOTLB device is enabled, the vring addresses we get
from userspace are GIOVAs. It is thus wrong to pass them down
to access_ok() which only takes HVAs.
Access validation is done at prefetch time with IOTLB. Teach
vq_access_ok() about that by moving the (vq->iotlb) check
from vhost_vq_access_ok() to vq_access_ok(). This prevents
vhost_vring_set_addr() to fail when verifying the accesses.
No behavior change for vhost_vq_access_ok().
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1883084
Fixes: 6b1e6cc785 ("vhost: new device IOTLB API")
Cc: jasowang@redhat.com
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/160171931213.284610.2052489816407219136.stgit@bahia.lan
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The MPTCP ADD_ADDR suboption with echo-flag=1 has no HMAC, the size is
smaller than the one initially sent without echo-flag=1. We then need to
use the correct size everywhere when we need this echo bit.
Before this patch, the wrong size was reserved but the correct amount of
bytes were written (and read): the remaining bytes contained garbage.
Fixes: 6a6c05a8b0 ("mptcp: send out ADD_ADDR with echo flag")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/95
Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such property as duplex-full. It's called full-duplex. Leading to
reduced speed when using the example as base for a real device tree.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unit address should be 1e, because the unit address is supposed
to be in hexadecimal.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a strictly cosmetic change that renames some macros in
sja1105_dynamic_config.c. They were copy-pasted in haste and this has
resulted in them having the driver prefix twice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
net/sched: Add actions for MPLS L2 VPNs
This patch series adds the necessary TC actions for supporting layer 2
MPLS VPNs (VPLS).
The objective is to give the possibility to add an MPLS header right
before an skb's mac header, then to prepend this MPLS packet with a
new Ethernet header with the MAC address of the next hop.
Patch 1 implements the actions for adding and removing the external
Ethernet header.
Patch 2 adds the possibility to push an MPLS header before the mac
header.
Most of the code already exists as these operations were first
implemented in openvswitch.
Practical example, with encap on Host-A and decap on Host-B:
Host-A# tc filter add dev ethAx ingress matchall \
action mpls mac_push label 20 \
action vlan push_eth dst_mac 02:00:00:00:00:02 \
src_mac 02:00:00:00:00:01 \
action mirred egress redirect dev ethAy
Host-B# tc filter add dev ethBx ingress protocol mpls_uc \
flower mpls_label 20 mpls_bos 1 \
action vlan pop_eth \
action mpls pop proto teb \
action mirred egress redirect dev ethBy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MAC_PUSH action which pushes an MPLS LSE before the mac
header (instead of between the mac and the network headers as the
plain PUSH action does).
The only special case is when the skb has an offloaded VLAN. In that
case, it has to be inlined before pushing the MPLS header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TCA_VLAN_ACT_POP_ETH and TCA_VLAN_ACT_PUSH_ETH, to
respectively pop and push a base Ethernet header at the beginning of a
frame.
POP_ETH is just a matter of pulling ETH_HLEN bytes. VLAN tags, if any,
must be stripped before calling POP_ETH.
PUSH_ETH is restricted to skbs with no mac_header, and only the MAC
addresses can be configured. The Ethertype is automatically set from
skb->protocol. These restrictions ensure that all skb's fields remain
consistent, so that this action can't confuse other part of the
networking stack (like GSO).
Since openvswitch already had these actions, consolidate the code in
skbuff.c (like for vlan and mpls push/pop).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the comparisons of u16 integers value and sopass_val with
less than zero for error checking is always false because the values
are unsigned. Fix this by making these variables int. This does not
affect the shift and mask operations performed on these variables
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: 49fc23018e ("net: phy: dp83869: support Wake on LAN")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for old hardware versions that did not have SMCDv2 support was
using suspicious pointer magic. Address the fields using an array.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building a CLC proposal message then the list of ISM devices does
not need to contain multiple devices that have the same chid value,
all these devices use the same function at the end.
Improve smc_find_ism_v2_device_clnt() to collect only ISM devices that
have unique chid values.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
===================
Add Seville Ethernet switch to T1040RDB
Seville is a DSA switch that is embedded inside the T1040 SoC, and
supported by the mscc_seville DSA driver inside drivers/net/dsa/ocelot.
This series adds this switch to the SoC's dtsi files and to the T1040RDB
board file.
I would like to send this series through net-next. There is no conflict
with other patches submitted to T1040 device tree. Maybe this could at
least get an ACK from devicetree maintainers.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.
A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the description of the embedded L2 switch inside the SoC dtsi file
for NXP T1040.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retransmission refactoring patch
686989700c ("tcp: simplify tcp_mark_skb_lost")
does not properly update the total lost packet counter which may
break the policer mode in BBR. This patch fixes it.
Fixes: 686989700c ("tcp: simplify tcp_mark_skb_lost")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BQ25980, BQ25975 and BQ25960 family of flash
chargers.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix many (lots deleted here) build errors in hinic by selecting NET_DEVLINK.
ld: drivers/net/ethernet/huawei/hinic/hinic_hw_dev.o: in function `mgmt_watchdog_timeout_event_handler':
hinic_hw_dev.c:(.text+0x30a): undefined reference to `devlink_health_report'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x1c): undefined reference to `devlink_fmsg_u32_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x126): undefined reference to `devlink_fmsg_binary_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_hw_reporter_dump':
hinic_devlink.c:(.text+0x1ba): undefined reference to `devlink_fmsg_string_pair_put'
ld: hinic_devlink.c:(.text+0x227): undefined reference to `devlink_fmsg_u8_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_alloc':
hinic_devlink.c:(.text+0xaee): undefined reference to `devlink_alloc'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_free':
hinic_devlink.c:(.text+0xb04): undefined reference to `devlink_free'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_register':
hinic_devlink.c:(.text+0xb26): undefined reference to `devlink_register'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_unregister':
hinic_devlink.c:(.text+0xb46): undefined reference to `devlink_unregister'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_create':
hinic_devlink.c:(.text+0xb75): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xb95): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xbac): undefined reference to `devlink_health_reporter_destroy'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_destroy':
Fixes: 51ba902a16 ("net-next/hinic: Initialize hw interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bin Luo <luobin9@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Cc: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
net/iucv: updates 2020-10-01
Just two (rare) patches, and both deal with smatch warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch complains about
net/iucv/iucv.c:1119 __iucv_message_receive() warn: inconsistent indenting
While touching this line, also make the return logic consistent and thus
get rid of a goto label.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch complains about
net/iucv/af_iucv.c:624 iucv_sock_bind() error: memcpy() 'sa->siucv_user_id' too small (8 vs 9)
Which is absolutely correct - the memcpy() takes 9 bytes (sizeof(uid))
from an 8-byte field (sa->siucv_user_id).
Luckily the sockaddr_iucv struct contains more data after the
.siucv_user_id field, and we checked the size of the passed data earlier
on. So the memcpy() won't accidentally read from an invalid location.
Fix the warning by reducing the size of the uid variable to what's
actually needed, and thus reducing the amount of copied data.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add yaml for the bq25980 flash charger.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
NETDEV_HW_ADDR_T_SLAVE is not used anymore, remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When I cat some module parameters by sysfs, it displays as follows.
It's better to add a newline for easy reading.
root@syzkaller:~# cd /sys/module/test_power/parameters/
root@syzkaller:/sys/module/test_power/parameters# cat ac_online
onroot@syzkaller:/sys/module/test_power/parameters# cat battery_present
trueroot@syzkaller:/sys/module/test_power/parameters# cat battery_health
goodroot@syzkaller:/sys/module/test_power/parameters# cat battery_status
dischargingroot@syzkaller:/sys/module/test_power/parameters# cat battery_technology
LIONroot@syzkaller:/sys/module/test_power/parameters# cat usb_online
onroot@syzkaller:/sys/module/test_power/parameters#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Johannes Berg says:
====================
genetlink per-op policy export
Here's a respin, now including Jakub's patch last so that it will
do the right thing from the start.
The first patch remains the same, of course; the others have mostly
some rebasing going on, except for the actual export patch (patch 4)
which is adjusted per Jakub's review comments about exporting the
policy only if it's actually used for do/dump.
To see that, the dump for "nlctrl" (i.e. the generic netlink control)
is instructive, because the ops are this:
{
.cmd = CTRL_CMD_GETFAMILY,
.validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
.policy = ctrl_policy_family,
.maxattr = ARRAY_SIZE(ctrl_policy_family) - 1,
.doit = ctrl_getfamily,
.dumpit = ctrl_dumpfamily,
},
{
.cmd = CTRL_CMD_GETPOLICY,
.policy = ctrl_policy_policy,
.maxattr = ARRAY_SIZE(ctrl_policy_policy) - 1,
.start = ctrl_dumppolicy_start,
.dumpit = ctrl_dumppolicy,
.done = ctrl_dumppolicy_done,
},
So we exercise both "don't have doit" and "GENL_DONT_VALIDATE_DUMP"
parts, and get (with the current genl patch):
$ genl ctrl policy name nlctrl
ID: 0x10 op 3 policies: do=0
ID: 0x10 op 10 policies: dump=1
ID: 0x10 policy[0]:attr[1]: type=U16 range:[0,65535]
ID: 0x10 policy[0]:attr[2]: type=NUL_STRING max len:15
ID: 0x10 policy[1]:attr[1]: type=U16 range:[0,65535]
ID: 0x10 policy[1]:attr[2]: type=NUL_STRING max len:15
ID: 0x10 policy[1]:attr[10]: type=U32 range:[0,4294967295]
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now CTRL_CMD_GETPOLICY can only dump the family-wide
policy. Support dumping policy of a specific op.
v3:
- rebase after per-op policy export and handle that
v2:
- make cmd U32, just in case.
v1:
- don't echo op in the output in a naive way, this should
make it cleaner to extend the output format for dumping
policies for all the commands at once in the future.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20201001225933.1373426-11-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-op policy dumping. The data is pretty much
as before, except that now the assumption that the policy with
index 0 is "the" policy no longer holds - you now need to look
at the new CTRL_ATTR_OP_POLICY attribute which is a nested attr
(indexed by op) containing attributes for do and dump policies.
When a single op is requested, the CTRL_ATTR_OP_POLICY will be
added in the same way, since do and dump policies may differ.
v2:
- conditionally advertise per-command policies only if there
actually is a policy being used for the do/dump and it's
present at all
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need this later for the per-op policy index dump.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the policy dump code a bit to support adding multiple
policies to a single dump, in order to e.g. support per-op
policies in generic netlink.
v2:
- move kernel-doc to implementation [Jakub]
- squash the first patch to not flip-flop on the prototype
[Jakub]
- merge netlink_policy_dump_get_policy_idx() with the old
get_policy_idx() we already had
- rebase without Jakub's patch to have per-op dump
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
