Use module_i2c_driver() to simplify driver init boilerplate.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no point to print deferred probe (and its failures to get
resources) as an error. In case of multiple probe tries this would
pollute the dmesg.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The PTN5150 chip can be used in hardware designs with only reporting of
USB Type-C connection, without the VBUS control. The driver however
unconditionally expected 'vbus-gpios'.
Since all uses of the VBUS GPIO descriptor are NULL safe, the code can
accept missing GPIO and provide only extcon status reporting.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When machine boots up, the USB could be already in OTG mode. In such
case there will be no interrupt coming to ptn5150 device and driver will
report default state of nothing connected. Detection of USB connection
would happen on first unplug of the cable.
Factor out code for checking current connection mode and call it right
after probe so the existing USB mode will be properly reported.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The ptn5150 driver always prints device type on probe but as raw hex,
without any translation to meaningful description. This is useful only
for board bring up time so lower the verbosity to debug.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Instead of obtaining GPIO as input and configuring it right after to
output-low, just use proper GPIOD_OUT_LOW flag. Code is smaller and
simpler.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Interrupts do not have to be always GPIO based so instead of expecting
"int-gpios" property and converting the GPIO to an interrupt, just
accept any interrupt via generic "interrupts" property.
Keep support for old "int-gpios" for backward compatibility.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver uses atomic version of gpiod_set_value() without any real
reason. It is called in a workqueue under mutex so it could sleep
there. Changing it to "can_sleep" flavor allows to use the driver with
all GPIO chips.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The PTN5150 chip can be used in hardware designs with only reporting of
USB Type-C connection, without the VBUS control.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Interrupts do not have to be always GPIO based so instead of expecting
"int-gpios" property and converting the GPIO to an interrupt, just
accept any interrupt via generic "interrupts" property.
Mark the old "int-gpios" as deprecated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Convert the ptn-5150 extcon driver bindings to DT schema format using
json-schema. The differences with original bindings document:
- Use "gpios" suffix for the "int" and "vbus" gpio,
- Skip generic "pinctrl" property as it is not really required.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Intel Atom Cherry Trail platform reports a new battery
name (BATC). Tested on ASUS Transformer Mini T103HAF.
Signed-off-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The WMI INIT method on for some reason turns on the camera LED on these
2-in-1s, without the WMI interface allowing further control over the LED.
To fix this commit b5f7311d3a ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA") added a blacklist with these 2 models on it
since the WMI driver did not add any extra functionality to these models.
Recently I've been working on making more 2-in-1 models report their
tablet-mode (SW_TABLET_MODE) to userspace; and I've found that these 2
Asus models report this through WMI. This commit reverts the adding
of the blacklist, so that the Asus WMI driver can be used on these
models to report their tablet-mode. I have another patch fixing the LED
issue in a different manner.
Note this is the second time the we revert the adding of the
asus_nb_wmi_blacklist. It was reverted before in commit:
aab9e7896e ("platform/x86: asus-nb-wmi: Revert "Do not load on Asus
T100TA and T200TA")"
But some how (accidentally re-applying of the patch?) it got re-added
again in commit 3bd12da7f5 ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA"), so now we need to revert it again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add touchscreen info for the MPMAN Converter9 2-in-1. This device uses the
same case as the ITworks TW891, but it uses a different digitizer, so it
needs its own firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit 653055b9ac ("vhost-vdpa: support get/set backend features")
introduces two malfunction backend features ioctls:
1) the ioctls was blindly added to vring ioctl instead of vdpa device
ioctl
2) vhost_set_backend_features() was called when dev mutex has already
been held which will lead a deadlock
This patch fixes the above issues.
Cc: Eli Cohen <elic@nvidia.com>
Reported-by: Zhu Lingshan <lingshan.zhu@intel.com>
Fixes: 653055b9ac ("vhost-vdpa: support get/set backend features")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200907104343.31141-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When devm_regulator_register() fails, ec should be
freed just like when olpc_ec_cmd() fails.
Fixes: 231c0c2161 ("Platform: OLPC: Add a regulator for the DCON")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware
block was increased. This patch updates the endpoint allocation for sam9x60
to take advantage of this larger memory. At the same time the
constraint to allocate the endpoints in order was lifted. To handle old
and new hardware in the same driver the ep_prealloc was added.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use 1 bank endpoints for control transfers
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Simplify the endpoint allocation and cleanup the code.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Instead of trying to match every possible compatible use
of_find_matching_node_and_match() and pass the compatible array.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A 100MHZ 32-bit timer will be wrapped up less than 43s. Although the
kernel maintains a software high 32-bit count in the tick IRQ. But it's
not applicable to the user mode APPs.
Note: The kernel still uses the lower 32 bits of the timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-9-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Use compatible = "hisilicon,sp804" mark as Hisilicon sp804 timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-8-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Currently, we get a timer register address by: add the constant register
offset to the timer base address. e.g. "base + TIMER_CTRL". It can not be
dynamically adjusted at run time.
So create a new structure "sp804_timer" to record the original registers
offset, and create a new structure "sp804_clkevt" to record the
calculated registers address. So the "base + TIMER_CTRL" is changed to
"clkevt->ctrl", this will faster than "base + timer->ctrl".
For example:
struct sp804_timer arm_sp804_timer = {
.ctrl = TIMER_CTRL,
};
struct sp804_clkevt clkevt;
clkevt.ctrl = base + arm_sp804_timer.ctrl.
- writel(0, base + TIMER_CTRL);
+ writel(0, clkevt->ctrl);
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-7-thunder.leizhen@huawei.com
Add two local variables: timer1_base and timer2_base in sp804_of_init(),
to avoid repeatedly calculate the base address of timer2, and make it
easier to recognize timer1. Hope to make the next patch looks more clear.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-6-thunder.leizhen@huawei.com
writel(0, base + TIMER_CTRL);
... ...
writel(xxx | TIMER_CTRL_PERIODIC, base + TIMER_CTRL);
The timer is just temporarily disabled, and it will be set to periodic
mode later.
The description of the field TimerMode of the register TimerXControl
as shown below:
0 = Timer module is in free-running mode (default)
1 = Timer module is in periodic mode.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-5-thunder.leizhen@huawei.com
Delete the leading "__" of __sp804_clocksource_and_sched_clock_init() and
__sp804_clockevents_init(), make it looks a little more comfortable.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-4-thunder.leizhen@huawei.com
Since commit 7484c727b6 ("ARM: realview: delete the RealView board
files") and commit 16956fed35 ("ARM: versatile: switch to DT only
booting and remove legacy code"), there's no one to use the functions
defined or declared in include/clocksource/timer-sp804.h. Delete it.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-3-thunder.leizhen@huawei.com
Move the clk_get_sys() part into sp804_get_clock_rate(), cleanup the same
code.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-2-thunder.leizhen@huawei.com
Document SoC specific compatible strings for r8a7742. No driver change
is needed as the fallback strings will activate the right code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200902091927.32211-1-prabhakar.mahadev-lad.rj@bp.renesas.com
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376 ("iommu/exynos: Add callback for initializing devices from device tree")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch extends the pkey kernel module to support CCA
and EP11 secure ECC (private) keys as source for deriving
ECC protected (private) keys.
There is yet another new ioctl to support this: PKEY_KBLOB2PROTK3
can handle all the old keys plus CCA and EP11 secure ECC keys.
For details see ioctl description in pkey.h.
The CPACF unit currently only supports a subset of 5
different ECC curves (P-256, P-384, P-521, ED25519, ED448) and
so only keys of this curve type can be transformed into
protected keys. However, the pkey and the cca/ep11 low level
functions do not check this but simple pass-through the key
blob to the firmware onto the crypto cards. So most likely
the failure will be a response carrying an error code
resulting in user space errno value EIO instead of EINVAL.
Deriving a protected key from an EP11 ECC secure key
requires a CEX7 in EP11 mode. Deriving a protected key from
an CCA ECC secure key requires a CEX7 in CCA mode.
Together with this new ioctl the ioctls for querying lists
of apqns (PKEY_APQNS4K and PKEY_APQNS4KT) have been extended
to support EP11 and CCA ECC secure key type and key blobs.
Together with this ioctl there comes a new struct ep11kblob_header
which is to be prepended onto the EP11 key blob. See details
in pkey.h for the fields in there. The older EP11 AES key blob
with some info stored in the (unused) session field is also
supported with this new ioctl.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Support for CCA APKA (used for CCA ECC keys) master keys.
The existing mkvps sysfs attribute for each queue for cards
in CCA mode is extended to show the APKA master key register
states and verification pattern:
Improve the mkvps sysfs attribute to display the APKA
master key verification patterns for old, current and new
master key registers. The APKA master key is used to
encrypt CCA ECC secure keys. The syntax is analog to the
existing AES mk verification patterns:
APKA NEW: <new_apka_mk_state> <new_apka_mk_mkvp>
APKA CUR: <cur_apka_mk_state> <cur_apka_mk_mkvp>
APKA OLD: <old_apka_mk_state> <old_apka_mk_mkvp>
with
<new_apka_mk_state>: 'empty' or 'partial' or 'full'
<cur_apka_mk_state>: 'valid' or 'invalid'
<old_apka_mk_state>: 'valid' or 'invalid'
<new_apka_mk_mkvp>, <cur_apka_mk_mkvp>, <old_apka_mk_mkvp>
8 byte hex string with leading 0x
MKVP means Master Key Verification Pattern and is a folded hash over
the key value. Only the states 'full' and 'valid' result in displaying
a useful mkvp, otherwise a mkvp of all bytes zero is shown. If for any
reason the FQ fails and the (cached) information is not available, the
state '-' will be shown with the mkvp value also '-'. The values shown
here are the very same as the cca panel tools displays.
The internal function cca_findcard2() also supports to match
against the APKA master key verification patterns and the pkey
kernel module which uses this function needed compatible rewrite
of these invocations.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
reqcnt is an u32 pointer but we do copy sizeof(reqcnt) which is the
size of the pointer. This means we only copy 8 byte. Let us copy
the full monty.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes: af4a72276d ("s390/zcrypt: Support up to 256 crypto adapters.")
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Prefer aux-voltage-chargeable over trickle-diode-disable and set diode
accordingly. This is then passed to the chip's appropriate charge setup
function.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-8-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
