POWER9 DD1 was never a product. It is no longer supported by upstream
firmware, and it is not effectively supported in Linux due to lack of
testing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Remove arch_make_huge_pte() entirely]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although it is often possible to recover a CPU that was interrupted
from OPAL with a system reset NMI, it's undesirable to interrupt them
for a few reasons. Firstly because dump/debug code itself needs to
call firmware, so it could hang on a lock or possibly corrupt a
per-cpu data structure if it or another CPU was interrupted from
OPAL. Secondly, the kexec crash dump code will not return from
interrupt to unwind the OPAL call.
Call OPAL_QUIESCE with QUIESCE_HOLD before sending an NMI IPI to
another CPU, which wait for it to leave firmware (or time out) to
avoid this problem in normal conditions. Firmware bugs may still
result in a timeout and interrupting OPAL, but that is the best
option (stops the CPU, and possibly allows firmware to be debugged).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the paca array into an array of pointers to pacas. Allocate
pacas individually.
This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.
This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Certain HMI's such as malfunction error propagate through
all threads/core on the system. If a thread was offline
prior to us crashing the system and jumping to the kdump
kernel, bad things happen when it wakes up due to an HMI
in the kdump kernel.
There are several possible ways to solve this problem
1. Put the offline cores in a state such that they are
not woken up for machine check and HMI errors. This
does not work, since we might need to wake up offline
threads to handle TB errors
2. Ignore HMI errors, setup HMEER to mask HMI errors,
but this still leads the window open for any MCEs
and masking them for the duration of the dump might
be a concern
3. Wake up offline CPUs, as in send them to
crash_ipi_callback (not wake them up as in mark them
online as seen by the hotplug). kexec does a
wake_online_cpus() call, this patch does something
similar, but instead sends an IPI and forces them to
crash_ipi_callback()
This patch takes approach #3.
Care is taken to enable this only for powenv platforms
via crash_wake_offline (a global value set at setup
time). The crash code sends out IPI's to all CPU's
which then move to crash_ipi_callback and kexec_smp_wait().
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2.1 and earlier has an issue where some cache inhibited
vector load will return bad data. The workaround is two part, one
firmware/microcode part triggers HMI interrupts when hitting such
loads, the other part is this patch which then emulates the
instructions in Linux.
The affected instructions are limited to lxvd2x, lxvw4x, lxvb16x and
lxvh8x.
When an instruction triggers the HMI, all threads in the core will be
sent to the HMI handler, not just the one running the vector load.
In general, these spurious HMIs are detected by the emulation code and
we just return back to the running process. Unfortunately, if a
spurious interrupt occurs on a vector load that's to normal memory we
have no way to detect that it's spurious (unless we walk the page
tables, which is very expensive). In this case we emulate the load but
we need do so using a vector load itself to ensure 128bit atomicity is
preserved.
Some additional debugfs emulated instruction counters are added also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Switch CONFIG_PPC_BOOK3S_64 to CONFIG_VSX to unbreak the build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we use the stop-api provided by the firmware to program the
SLW engine to restore the values of hypervisor resources that get lost
on deeper idle states (such as winkle). Since the deep states were
only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
woken up by decrementer.
On POWER9, some of the deep platform idle states such as stop4 can be
used in cpuidle as well. In this case, we want the CPU in stop4 to be
woken up by the decrementer when some timer on the CPU expires.
In this patch, we program the stop-api for LPCR with PECE1
bit cleared only when we are offlining the CPU and set it
back once the CPU is online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check for validity of cpu before calling get_hard_smp_processor_id().
Found with coverity.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
nr_cpu_ids can be limited by nr_cpus boot parameter, whereas NR_CPUS is a
compile time constant, which shouldn't be compared against during cpu kick.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During secondary start, we do not need to BUG_ON if an invalid CPU number
is passed. We already print an error if secondary cannot be started, so
just return an error instead.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than concern ourselves with any soft-mask logic in the CPU
hotplug handler, just hard disable interrupts. This ensures there
are no lazy-irqs pending, which means we can call directly to idle
instruction in order to sleep.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This simplifies the asm and fixes irq-off tracing over sleep
instructions.
Also move powersave_nap check for POWER8 into C code, and move
PSSCR register value calculation for POWER9 into C.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Have the NMI IPI code use this op when the platform defines it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recently we merged the native xive support for Power9, and then separately some
reworks for doorbell IPI support. In isolation both series were OK, but the
merged result had a bug in one case.
On P9 DD1 we use pnv_p9_dd1_cause_ipi() which tries to use doorbells, and then
falls back to the interrupt controller. However the fallback is implemented by
calling icp_ops->cause_ipi. But now that xive support is merged we might be
using xive, in which case icp_ops is not initialised, it's a xics specific
structure. This leads to an oops such as:
Unable to handle kernel paging request for data at address 0x00000028
Oops: Kernel access of bad area, sig: 11 [#1]
NIP pnv_p9_dd1_cause_ipi+0x74/0xe0
LR smp_muxed_ipi_message_pass+0x54/0x70
To fix it, rather than using icp_ops which might be NULL, have both xics and
xive set smp_ops->cause_ipi, and then in the powernv code we save that as
ic_cause_ipi before overriding smp_ops->cause_ipi. For paranoia add a WARN_ON()
to check if somehow smp_ops->cause_ipi is NULL.
Fixes: b866cc2199 ("powerpc: Change the doorbell IPI calling convention")
Tested-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 requires msgsync for receiver-side synchronization, and a DD1
workaround restricts IPIs to core-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop no longer needed asm feature macro changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.
Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges the arch part of the XIVE support, leaving the final commit
with the KVM specific pieces dangling on the branch for Paul to merge
via the kvm-ppc tree.
Move the piece of code in powernv/smp.c::pnv_smp_cpu_kill_self() which
transitions the CPU to the deepest available platform idle state to a
new function named pnv_cpu_offline() in powernv/idle.c. The rationale
behind this code movement is that the data required to determine the
deepest available platform state resides in powernv/idle.c.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to split <linux/sched/hotplug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/hotplug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access to
devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to be used by
glibc.
- The ability for a guest to ask the hypervisor to resize the guest's hash
table, and in addition support for doing so automatically when memory is
hotplugged into/out-of the guest. This allows the hash table to be sized
based on the current memory usage of the guest, rather than the maximum
possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which includes
support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton Blanchard,
Benjamin Herrenschmidt, Chris Packham, Daniel Axtens, Daniel Borkmann, David
Gibson, Finn Thain, Gautham R. Shenoy, Gavin Shan, Greg Kurz, Joel Stanley,
John Allen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi
Bangoria, Reza Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Icle
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access
to devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to
be used by glibc.
- The ability for a guest to ask the hypervisor to resize the guest's
hash table, and in addition support for doing so automatically when
memory is hotplugged into/out-of the guest. This allows the hash
table to be sized based on the current memory usage of the guest,
rather than the maximum possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which
includes support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"
* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
powerpc/mm/radix: Skip ptesync in pte update helpers
powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
powerpc/mm/radix: Update pte update sequence for pte clear case
powerpc/mm: Update PROTFAULT handling in the page fault path
powerpc/xmon: Fix data-breakpoint
powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
powerpc/pseries: Fix typo in parameter description
powerpc/kprobes: Remove kprobe_exceptions_notify()
kprobes: Introduce weak variant of kprobe_exceptions_notify()
powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
powerpc/powernv: Fix opal_exit tracepoint opcode
powerpc: Add a prototype for mcount() so it can be versioned
powerpc: Drop GPL from of_node_to_nid() export to match other arches
powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
powerpc/kprobes: Implement Optprobes
powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
powerpc: Add helper to check if offset is within relative branch range
powerpc/bpf: Introduce __PPC_SH64()
...
The IPIs come in as HVI not EE, so we need to test the appropriate
SRR1 bits. The encoding is such that it won't have false positives
on P7 and P8 so we can just test it like that. We also need to handle
the icp-opal variant of the flush.
Fixes: d74361881f ("powerpc/xics: Add ICP OPAL backend")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The power9_idle_stop method currently takes only the requested stop
level as a parameter and picks up the rest of the PSSCR bits from a
hand-coded macro. This is not a very flexible design, especially when
the firmware has the capability to communicate the psscr value and the
mask associated with a particular stop state via device tree.
This patch modifies the power9_idle_stop API to take as parameters the
PSSCR value and the PSSCR mask corresponding to the stop state that
needs to be set. These PSSCR value and mask are respectively obtained
by parsing the "ibm,cpu-idle-state-psscr" and
"ibm,cpu-idle-state-psscr-mask" fields from the device tree.
In addition to this, the patch adds support for handling stop states
for which ESL and EC bits in the PSSCR are zero. As per the
architecture, a wakeup from these stop states resumes execution from
the subsequent instruction as opposed to waking up at the System
Vector.
The older firmware sets only the Requested Level (RL) field in the
psscr and psscr-mask exposed in the device tree. For older firmware
where psscr-mask=0xf, this patch will set the default sane values that
the set for for remaining PSSCR fields (i.e PSLL, MTL, ESL, EC, and
TR). For the new firmware, the patch will validate that the invariants
required by the ISA for the psscr values are maintained by the
firmware.
This skiboot patch that exports fully populated PSSCR values and the
mask for all the stop states can be found here:
https://lists.ozlabs.org/pipermail/skiboot/2016-September/004869.html
[Optimize the number of instructions before entering STOP with
ESL=EC=0, validate the PSSCR values provided by the firimware
maintains the invariants required as per the ISA suggested by Balbir
Singh]
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If hardware supports stop state, use the deepest stop state when
the cpu is offlined.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Long ago, only in the lab, there was OPALv1 and OPALv2. Now there is
just OPALv3, with nobody ever expecting anything on pre-OPALv3 to
be cared about or supported by mainline kernels.
So, let's remove FW_FEATURE_OPALv3 and instead use FW_FEATURE_OPAL
exclusively.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPALv2 only ever existed in the lab and didn't escape to the world.
All OPAL systems in the wild are OPALv3.
The probability of there being an OPALv2 system still powered on
anywhere inside IBM is approximately zero, let alone anyone
expecting to run mainline kernels.
So, start to remove references to OPALv2.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a bug where it is possible for an off-line CPU to fail to go
into a low-power state (nap/sleep/winkle), and to become unresponsive to
requests from the KVM subsystem to wake up and run a VCPU. What can
happen is that a maskable interrupt of some kind (external, decrementer,
hypervisor doorbell, or HMI) after we have called local_irq_disable() at
the beginning of pnv_smp_cpu_kill_self() and before interrupts are
hard-disabled inside power7_nap/sleep/winkle(). In this situation, the
pending event is marked in the irq_happened flag in the PACA. This
pending event prevents power7_nap/sleep/winkle from going to the
requested low-power state; instead they return immediately. We don't
deal with any of these pending event flags in the off-line loop in
pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case,
so we will have srr1 == 0, and none of the processing to clear
interrupts or doorbells will be done.
Usually, the most obvious symptom of this is that a KVM guest will fail
with a console message saying "KVM: couldn't grab cpu N".
This fixes the problem by making sure we handle the irq_happened flags
properly. First, we hard-disable before the off-line loop. Once we have
hard-disabled, the irq_happened flags can't change underneath us. We
unconditionally clear the DEC and HMI flags: there is no processing of
timer interrupts while off-line, and the necessary HMI processing is all
done in lower-level code. We leave the EE and DBELL flags alone for the
first iteration of the loop, so that we won't fail to respond to a
split-core request that came in just before hard-disabling. Within the
loop, we handle external interrupts if the EE bit is set in irq_happened
as well as if the low-power state was interrupted by an external
interrupt. (We don't need to do the msgclr for a pending doorbell in
irq_happened, because doorbells are edge-triggered and don't remain
pending in hardware.) Then we clear both the EE and DBELL flags, and
once clear, they cannot be set again (until this CPU comes online again,
that is).
This also fixes the debug check to not be done when we just ran a KVM
guest or when the sleep didn't happen because of a pending event in
irq_happened.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
The powernv code has some conditional support for running on bare metal
machines that have no OPAL firmware, but provide RTAS.
No released machines ever supported that, and even in the lab it was
just a transitional hack in the days when OPAL was still being
developed.
So remove the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Since we can now use hypervisor doorbells for host IPIs, this makes
sure we clear the host IPI flag when taking a doorbell interrupt, and
clears any pending doorbell IPI in pnv_smp_cpu_kill_self() (as we
already do for IPIs sent via the XICS interrupt controller). Otherwise
if there did happen to be a leftover pending doorbell interrupt for
an offline CPU thread for any reason, it would prevent that thread from
going into a power-saving mode; it would instead keep waking up because
of the interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Starting with POWER8, the subcore logic relies on all threads of a core
being booted so that they can participate in split mode switches. So on
those machines we ignore the smt_enabled_at_boot setting (smt-enabled on
the kernel command line).
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
[mpe: Update comment and change log to be more precise]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The secondary threads should enter deep idle states so as to gain maximum
powersavings when the entire core is offline. To do so the offline path
must be made aware of the available deepest idle state. Hence probe the
device tree for the possible idle states in powernv core code and
expose the deepest idle state through flags.
Since the device tree is probed by the cpuidle driver as well, move
the parameters required to discover the idle states into an appropriate
common place to both the driver and the powernv core code.
Another point is that fastsleep idle state may require workarounds in
the kernel to function properly. This workaround is introduced in the
subsequent patches. However neither the cpuidle driver or the hotplug
path need be bothered about this workaround.
They will be taken care of by the core powernv code.
Originally-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a secondary hardware thread has finished running a KVM guest, we
currently put that thread into nap mode using a nap instruction in
the KVM code. This changes the code so that instead of doing a nap
instruction directly, we instead cause the call to power7_nap() that
put the thread into nap mode to return. The reason for doing this is
to avoid having the KVM code having to know what low-power mode to
put the thread into.
In the case of a secondary thread used to run a KVM guest, the thread
will be offline from the point of view of the host kernel, and the
relevant power7_nap() call is the one in pnv_smp_cpu_disable().
In this case we don't want to clear pending IPIs in the offline loop
in that function, since that might cause us to miss the wakeup for
the next time the thread needs to run a guest. To tell whether or
not to clear the interrupt, we use the SRR1 value returned from
power7_nap(), and check if it indicates an external interrupt. We
arrange that the return from power7_nap() when we have finished running
a guest returns 0, so pending interrupts don't get flushed in that
case.
Note that it is important a secondary thread that has finished
executing in the guest, or that didn't have a guest to run, should
not return to power7_nap's caller while the kvm_hstate.hwthread_req
flag in the PACA is non-zero, because the return from power7_nap
will reenable the MMU, and the MMU might still be in guest context.
In this situation we spin at low priority in real mode waiting for
hwthread_req to become zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI. A misdirected device interrupt could also
potentially cause it to wake up. In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.
In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt. This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally. Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.
To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs. Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel. Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap. This new function reads the
interrupt from the XICS. If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.
The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA. Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag. The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled. This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables POWER8 doorbell IPIs on powernv.
Since doorbells can only IPI within a core, we test to see when we can use
doorbells and if not we fall back to XICS. This also enables hypervisor
doorbells to wakeup us up from nap/sleep via the LPCR PECEDH bit.
Based on tests by Anton, the best case IPI latency between two threads dropped
from 894ns to 512ns.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upcoming POWER8 chips support a concept called split core. This is where the
core can be split into subcores that although not full cores, are able to
appear as full cores to a guest.
The splitting & unsplitting procedure is mildly complicated, and explained at
length in the comments within the patch.
One notable detail is that when splitting or unsplitting we need to pull
offline cpus out of their offline state to do work as part of the procedure.
The interface for changing the split mode is via a sysfs file, eg:
$ echo 2 > /sys/devices/system/cpu/subcores_per_core
Currently supported values are '1', '2' and '4'. And indicate respectively that
the core should be unsplit, split in half, and split in quarters. These modes
correspond to threads_per_subcore of 8, 4 and 2.
We do not allow changing the split mode while KVM VMs are active. This is to
prevent the value changing while userspace is configuring the VM, and also to
prevent the mode being changed in such a way that existing guests are unable to
be run.
CPU hotplug fixes by Srivatsa. max_cpus fixes by Mahesh. cpuset fixes by
benh. Fix for irq race by paulus. The rest by mikey and mpe.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support split core we need to be able to force all secondaries into
nap, so the core can detect they are idle and do an unsplit.
Currently power7_nap() will return without napping if there is an irq
pending. We want to ignore the pending irq and nap anyway, we will deal
with the interrupt later.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is no need to put a function descriptor in
__secondary_hold_spinloop. Use ppc_function_entry to get the
instruction address and put it in __secondary_hold_spinloop instead.
Also fix an issue where we assumed cur_cpu_spec held a function
descriptor.
Signed-off-by: Anton Blanchard <anton@samba.org>
T4, Cell, powernv, and pseries had the same implementation, so switch
them to use a generic version. A2 apparently had a version, but
removed it at some point, so we remove the declaration, too.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the powerpc uses of the __cpuinit macros. There
are no __CPUINIT users in assembly files in powerpc.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
'system_state < SYSTEM_RUNNING' will have same effect
with 'system_state == SYSTEM_BOOTING', but the later
one is more clearer.
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code fails to handle kexec on OPALv2. This fixes it
and adds code to improve the situation on OPALv3 where we can
query the CPU status from the firmware and decide what to do
based on that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If OPAL returns an error, propagate it upward rather than spinning
seconds waiting for a CPU that will never show up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
