Note that with the rc-feedback trigger, the cir-rx trigger is now
redundant. The cir-tx trigger is not used by default; if this
functionality is desired then it should exist in rc-core, not in
a driver.
Also make sure that the led is suspended on suspend.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Many devices with an ir receiver also have a feedback led. Add the
led trigger to support this.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The length in the header excludes the header itself, so we're getting
spurious readings.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the clock framework makes it possible to assign a device specific name to
the clocks, remove the ability to use a named clock in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The PLL calculation heuristics is rather complicated and and is often
difficult to understand to its original author.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
clamp_t does the job to put a variable into the given range.
clamp_t -> clamp as agreed with Andy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Configure the device external clock using the common clock framework
instead of a board code callback function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hello,
this is a new gspca driver for Syntek STK1135 webcams. The code is completely
new, but register values are based on Syntekdriver (stk11xx) by Nicolas VIVIEN
(http://syntekdriver.sourceforge.net).
Only one webcam type is supported now - vendor 0x174f, device 0x6a31.
It's Asus F5RL laptop flippable webcam with MT9M112.
The camera works better than in Windows - initializes much faster and
provides more resolutions (the sensor can do almost any resolution - just
add it to the stk1135_modes[] - could this feature be somehow used by
applications to avoid SW scaling?).
Autoflip works too - when the camera is flipped around, the image is flipped
automatically.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If v4l2_fh_open() fails in dev_open(), gspca_dev->module left locked.
The patch adds module_put(gspca_dev->module) on this path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We've an user reporting a device with a software version of 0, which works
fine. Once we lower the version check to accept version 0 it becomes a nop,
so remove it completely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c: In function 'sh_mobile_ceu_clock_start':
drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c:613:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When gsc is in runtime suspended state, there is no need to call
m2m_suspend during suspend and similarly, there is no need to call
m2m_resume during resume if already in runtime suspended state. This
patch adds the necessary conditions to achieve this.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__fimc_is_hw_update_param is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dev->of_node could be NULL. Hence check for the same and return before
dereferencing it in the subsequent error message.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Resolution set on ISP pad of S5C73M3-OIF subdev should be
propagated to source pad for TRY and ACTIVE formats.
The patch adds missing propagation for TRY format.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the mt9m111 driver to asynchronous subdevice probing. Synchronous
probing is also still possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mt9t031 driver hasn't yet been updated to support asynchronous
subdevice probing. If such a probing is attempted, the driver is allowed
to fail, but it shouldn't Oops. This patch fixes such a potential NULL
pointer dereference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The soc-camera core does all the work on supporting asynchronous
subdevice probing, host drivers only have to pass a subdevice list to
soc-camera. Typically this list is provided by the platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_MBUS_FMT_* codes are defined in v4l2-mediabus.h as hexadecimal
constants. Print them in the same form for easier recognition.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use devm_* resource allocators to simplify the driver's probe and clean up
paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With synchronous subdevice probing regulators should be requested by the
soc-camera core in soc_camera_pdrv_probe(). Subdevice drivers, supporting
asynchronous probing, call soc_camera_power_init() to request regulators.
Erroneously, the same regulator array is used in the latter case as in
the former, which leads to a failure. This patch fixes it by preventing
the second regulator request from being executed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
media_build/v4l/soc_camera.c: In function 'soc_camera_host_register':
media_build/v4l/soc_camera.c:1513:10: warning: 'sasd' may be used uninitialized in this function [-Wmaybe-uninitialized]
snprintf(clk_name, sizeof(clk_name), "%d-%04x",
^
media_build/v4l/soc_camera.c:1464:34: note: 'sasd' was declared here
struct soc_camera_async_subdev *sasd;
^
By changing the type of 'i' to unsigned and changing a condition we finally
convince the compiler that sasd is really initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add Renesas R-Car VIN (Video In) V4L2 driver.
Based on the patch by Phil Edworthy <phil.edworthy@renesas.com>.
[Sergei: removed deprecated IRQF_DISABLED flag, reordered/renamed 'enum chip_id'
values, reordered rcar_vin_id_table[] entries, removed senseless parens from
to_buf_list() macro, used ALIGN() macro in rcar_vin_setup(), added {} to the
*if* statement and used 'bool' values instead of 0/1 where necessary, removed
unused macros, done some reformatting and clarified some comments.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Calling v4l2_async_notifier_unregister() on a notifier that hasn't been
registered leads to a crash. To simplify drivers, make it safe to
unregister a notifier that has not been registered.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The of_get_child_by_name() function takes a reference to the node it
returns. Make sure to drop it when looking for the ports node in
v4l2_of_get_next_endpoint().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace a manual loop through child nodes with a call to
of_get_child_by_name().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For output buffers application provide to the kernel the number of bytes
they stored in each plane of the buffer. Verify that the value is
smaller than or equal to the plane length.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 2ccf12a did a crappy job when added multi-line comment lines,
violating CodingStyle.
Change the comments added there to fulfill CodingStyle, and document
the platform_data using Documentation/kernel-doc-nano-HOWTO.txt.
Cc: Jon Arne Jørgensen <jonarne@jonarne.no>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch implements i2c_board_info.platform_data, and some options to
override the default initialization table for the GM7113C and SAA7113
chips.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the registers changed in saa7115_init_misc table are out of range
for the gm7113c chip.
The only register that's within range, don't need to be changed here.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa711x_set_v4lstd would toggle several bits that should not be touched
when changing std. This patch fixes this.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by using the new dv_timings helpers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new blanking and frame size defines. This also fixed a bug in
these drivers: they assumed that the height for interlaced formats was
the field height, however height is the frame height. So the height
for a field is actually bt->height / 2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-common.c contained a bunch of dv-timings related functions.
Move that to the new v4l2-dv-timings.c which is a more appropriate
place for them.
There aren't many drivers that do HDTV, so it is a good idea to separate
common code related to that into a module of its own.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This module makes it easy to filter valid timings from the full list of
CEA and DMT timings based on the timings capabilities.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move tea575x from sound/i2c/other to drivers/media/radio
Includes Kconfig changes by Hans Verkuil.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Deferred probe was added in order to avoid udev vs. Kernel firmware
download problems. It is not needed anymore.
https://bugzilla.redhat.com/show_bug.cgi?id=827538
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to access bInterfaceNumber via dvb_usb_v2 internals as driver
has it already.
That patch is prepare for dvb_usb_v2 deferred probe hack removal. It was
added due to udev firmware loading problems, but things are fixed after
that and it is not needed anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I did some tests against modulator (television signal generator) and this
seems to improve sensitivity a little bit on channel I used. Used device
was able to receive transmission just as weak signal as with Windows XP.
Thanks to Jacek for donating his non-working device. I cannot ask he to
test anymore...
Reported-by: Jacek Konieczny <jajcus@jajcus.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 driver allows to define the maximum number of each module
such as RPF, WPF, and UDS in a platform data definition.
This suppresses operations for nonexistent or unused modules.
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
