e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.
Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some rare cases, we might get a VSI with no queues. In this case, we
cannot configure RSS on this VSI as it will try to divide by zero when
configuring the lookup table.
Change-ID: I6ae173a7dd3481a081e079eb10eb80275de2adb0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The return value from i40e_shutdown_adminq() is always 0
(I40E_SUCCESS). So, the test for non-0 will never be true. Cleanup
by removing the test and debug print statement.
Change-ID: Ie51e8e37515c3e3a6a9ff26fa951d0e5e24343c1
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40e_fdir_check_and_reenable(), the driver performs some checks to
determine whether it is safe to re-enable FD Sideband and FD ATR
support. The current check will only determine if there is available
space in the flow director table. However, this ignores the fact that
ATR should be disabled when there are TCP/IPv4 sideband rules in effect.
Add the missing check, and update the info message printed when
I40E_DEBUG_FD is enabled.
Change-ID: Ibb9c63e5be95d63c53a498fdd5dbf69f54a00e08
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.
Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.
Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.
Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which deleting a mac filter does not actually
occur. The driver reports that the filter has been deleted with no
error. The problem occurs because the wrong cmd_flag is passed to the
firmware when deleting the filter. The firmware reports an error back
to the driver but it is expressly ignored.
This fixes the bug by using the correct flag when deleting a filter.
Without this patch, deleted filters remain in firmware and function as
if they had not been deleted.
Change-ID: I5f22b874f3b83f457702f18f0d5602ca21ac40c3
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where driver shows 100 Mbps as a supported speed,
and allows it to be configured for advertising on X722 devices. This patch
fixes the problem by not setting the 100 Mbps SGMII flag for X722 devices.
Without this patch, the user incorrectly thinks that 100 Mbps is supported
and hence might try to advertise it on X722 devices when it is actually not
a supported speed.
Change-ID: I8c3d7c4251a9402d98994ed29749b7b895a0f205
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where we were byte swapping the port
parameter, then byte swapping it again in function execution.
Obviously, that's unnecessary, so take it out of the function calls.
Without this patch, the udp based tunnel configuration would
not be correct.
Change-ID: I788d83c5bd5732170f1a81dbfa0b1ac3ca8ea5b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled. But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled. This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.
This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure. It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.
Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the bug which causes RSS to continue to work
after being disabled. After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue. This patch also addresses the issue of reinstating
the lookup table should RSS then be re-enabled.
Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."
Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.
This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.
Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are resetting the pf stats we should also reset the RX csum
error stat.
Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-07-22
This series contains updates to i40e and i40evf.
Heinrich Schuchardt found a possible null pointer being dereferenced in
i40e_debug_aq(), fixed the issue by doing the variable assignment after
we are sure the pointer is not null.
Avinash fixed an issue when link was down, we were not showing the
correct advertised link modes.
Mitch cleans up a useless initializer since the variable is assigned
right away. Refactors the receive filter handling to properly track
filter adds and deletes so the driver will not lose filters during a
reset and up/down cycles. Also added a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Catherine removes a device id which is not needed (or used). Moves
a mutex lock since we need to lock the client list around the
i40e_client_release() call to prevent the release from interrupting
the client instances while they are being added.
Joshua adds Hyper-V specific VF device ids.
Amitoj Kaur Chawla cleans up a redundant memset() call before a memcpy().
Stefan Assmann adds the missing link advertise for some x710 NICs.
Tushar Dave fixes and issue found on SPARC, where a PF reset clears MAC
filters and if a platform-specific MAC address is used, the driver has
to explicitly write default MAC address to MAC filters otherwise all
incoming traffic destined to the default MAC address will be dropped
after reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
i40e PF reset clears mac filters. If platform-specific mac address
is used, driver has to explicitly write default mac address to mac
filters otherwise all incoming traffic destined to default mac
address will be dropped after reset.
This issue was found on SPARC while toggling i40e ntuple via ethtool.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant call to memset before a call to memcpy.
The Coccinelle semantic patch used to make this change is as follows:
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly track filter adds and deletes so the driver doesn't lose filters
during resets and up/down cycles. Add a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Implement a simple state machine so the driver can track the status of
each filter throughout its lifecycle. Properly manage the overflow promiscuous
state for the each VSI, and provide a way for the driver to detect when to exit
overflow promiscuous mode.
Remove all possible default MAC filters that the firmware may have set up so
that the driver can manage these correctly, particularly when VLANs come into
play. Remove the LAA flag for filters; instead just send whatever we get through
set_mac to the firmware as the LAA for wakeup purposes.
Finally, add the state of each filter to debugfs output so we can see what's
going on inside the driver's pointy little head.
Change-ID: I97c5e366fac2254fa01eaff4f65c0af61dcf2e1f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device ID is not needed, so take it out.
Change-ID: I148d29f68a1f58b03980ecd83047a1b440f4f74d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the q_vector initialization routine sets the affinity_mask
of a q_vector based on v_idx value. Meaning a loop iterates on v_idx,
which is an incremental value, and the cpumask is created based on
this value.
This is a problem in systems with multiple logical CPUs per core (like in
SMT scenarios). If we disable some logical CPUs, by turning SMT off for
example, we will end up with a sparse cpu_online_mask, i.e., only the first
CPU in a core is online, and incremental filling in q_vector cpumask might
lead to multiple offline CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
This patch changes the way q_vector's affinity_mask is created: it iterates
on v_idx, but consumes the CPU index from the cpu_online_mask instead of
just using the v_idx incremental value.
No functional changes were introduced.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets VSI broadcast promiscuous mode during VSI add sequence
and prevents adding MAC filter if specified MAC address is broadcast.
Change-ID: Ia62251fca095bc449d0497fc44bec3a5a0136773
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When LLDP/DCBX change happens the i40e driver code flow tried to
notify the client(s) for each of the PF VSIs. This resulted into
kernel panic on the first VSI that didn't have any netdev
associated to it.
The DCB change notification to the client(s) should be done only
once for the PF/LAN VSI where the client(s) instances have been
added to. Also, move the notification call after the PF driver has
made changes related to the updated DCB configuration.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald J Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems with 128 CPUs, turning off TSO results in errors,
i40e 0000:03:00.0: failed to get tracking for 1 vectors for VSI 400, err=-12
i40e 0000:03:00.0: Couldn't create FDir VSI
i40e 0000:03:00.0: i40e_ptp_init: PTP not supported on eth0
i40e 0000:03:00.0: couldn't add VEB, err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOENT
i40e 0000:03:00.0: rebuild of switch failed: -1, will try to set up simple PF connection
i40e 0000:03:00.0 eth0: adding 00:10:e0:8a:24:b6 vid=0
Enabling FD_SB without checking availability of MSI-X vector is the
root cause. This change adds necessary check.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the macaddr add and delete happens asynchronously, error
messages don't easily get associated to the actual request. Here
we add a bit of information to the error messages to help
determine the source of the error.
Change-ID: Id2d6df5287141c3579677d72d8bd21122823d79f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the need for a reset when the device enters limited promiscuous
mode. This was causing heartburn for people who were using VFs and
bridging, since this would require all of the VFs to undergo a reset
each time the PF changed its promiscuity.
Change-ID: I0a83495c5e4d68112bbc7a7a076d20fa8dd3b61c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting qcount to pf->num_lan_msix, effectively limits the RSS queues
to only use the number of CPUs, and ignore all other queues. We don't
want to do this. If the user has changed the RSS settings to use more
queues then CPUS, we want to trust they know what they are doing and
let them. More importantly, if we tell them that is what we did, we want
to actually do it and allow traffic into all of the queues we have
allocated. This does not change the default setting to initially
allocate only the number of CPUS of queue pairs.
Change-ID: Ie941a96e806e4bcd016addb4e17affb46770ada5
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function was failing to save PCI state
and this would result in a kernel stack trace from a WARN_ONCE in the
pci_legacy_suspend() function.
Add a call to pci_save_state() to fix that problem.
Change-ID: I4736e62bb660966bd208cc8af617a14cb07fc4bd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function calls another function that preps the device
for the power save and resume by freeing all the Tx/Rx resources and
interrupts but that function does not free the "other" causes interrupt
vector and IRQ. It also fails to call synchronize_irq() before freeing
the IRQ vectors. This sometimes may result in some AER errors on those
systems with that PCIe error reporting feature enabled.
Call synchronize_irq() before freeing IRQ vectors and explicitly free
the other causes interrupt resources and shut down that MSIX interrupt.
Change-ID: Ib88e4536756518a352446da0232189716618ad81
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).
Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
previous patches removed all direct accesses to dev->trans_start,
so change the netif_trans_update helper to update trans_start of
netdev queue 0 instead and then remove trans_start from struct net_device.
AFAICS a lot of the netif_trans_update() invocations are now useless
because they occur in ndo_start_xmit and driver doesn't set LLTX
(i.e. stack already took care of the update).
As I can't test any of them it seems better to just leave them alone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers. As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.
The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a device ID for X722.
Change-Id: I574f2345ab341de98a6a1c212d0603af853e48b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_release_rx_desc was in two files, but was only used
and needed in txrx.c. Get rid of the extra copy.
Change-Id: I86e18239aa03531fc198b6c052847475084a9200
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this change a non trusted VF can never fall to promiscuous
mode when there is no room for a MAC/VLAN filter.
Change-Id: I8a155aa25c0bcdc6093414920c9ade4ee0bd20e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The feature flags list for i40e and i40evf is beginning to become pretty
massive. I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.
The primary change here is that we now build our features list around
hw_encap_features. After that we assign that to vlan_features,
hw_features, and finally map that onto features. In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC. However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.
For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds hook to support changing a VF from not-trusted
to trusted and vice-versa. Fixed the wrappers and function prototype.
Changed the dmesg to reflex the current state better. This patch also
disables turning on/off trusted VF in MFP mode.
Change-ID: Ibcd910935c01f0be1f3fdd6d427230291ee92ebe
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't set our internal debug_mask at startup unless we get specific signal
to from the debug module parameter.
This should take care of the issue with all the device capabilities getting
printed even when we hadn't asked for the debug info.
Change-ID: I7fbc6bd8b11ed9b0631ec018ff36015a04100b6c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new device ID is 0x37D3 and it should follow the same flows and
branding string as for 0x37D0.
Change-ID: Ia5ad4a1910268c4666a3fd46a7afffbec55b4fc2
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the Capability for XL710/X710 devices with FW API
version higher than 1.4 to do geneve Rx offload.
Change-ID: I9a8f87772c48d7d67dc85e3701d2e0b845034c0b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was an error introduced with commit 3fced53507 ("i40e: X722 is
on the IOSF bus and does not report the PCI bus info"), where code was
added but the enabling flag is never set.
CC: Anjali Singhai Jain <anjali.singhai@intel.com>
CC: Stefan Assman <sassman@redhat.com>
Fixes: 3fced53507 ("i40e: X722 is on the IOSF bus ...")
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to suspend scheduling or any pending service task during driver
unload process, so that new task will not be scheduled. This patch sets
the suspend flag bit during reload which avoids service task execution.
Change-ID: I017c57b5d6656564556e3c5387da671369a572ac
Signed-off-by: Pandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive. We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.
Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return from i40e_vsi_reinit_setup() if vsi param is NULL.
This makes this code consistent with all the other code that
checks for NULL before using one of the VSI pointers accessed
with an indexed variable. (Indexed VSI pointers are
intentionally set to NULL in i40e_vsi_clear() and
i40e_remove().
Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985
Signed-off-by: John Underwood <johnx.underwood@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes an issue where a previously removed message
has returned. Changing the message type to dev_dbg
leaves the info, if desired, but takes it out of normal
everyday usage. Also changed call to only provide port
data when its valid and not when its not (delete case).
Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like Tx queues don't wait for Rx queues to be disabled before
DCB has been reconfigured.
Check the queues are disabled only after the DCB configuration has
been applied to the VSI(s) managed by the PF driver.
In case of any timeout issue a PF reset to recover.
Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums. As such we can update the
feature flags to reflect that.
In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the documentation in the datasheets for the XL710 do not call out
any reason to exclude support for IPv6 based tunnels. As such I am
dropping the code that was excluding these tunnel types from having their
port numbers recognized. This way we can take advantage of things such as
checksum offload for inner headers over IPv6 based VXLAN or GENEVE
tunnels.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.
Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The queues should never be enabled/disabled in the interrupt handler,
ICR0 interrupt enable should be the only thing that needs to be
dynamically changed in the handler.
This patch fixes that. Without this patch X722 platforms were
seeing weird ping timings when in Legacy mode since it takes
a whole lot of time for the HW/FW to re-enable queues.
Change-ID: If065afc45d81c5a19d4a94a00cd5b8f61cefc40c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch falls back to enabling unicast, multicast and
broadcast promiscuous mode when the driver must disable it's use
of "default port" aka defport mode (which is normally used to
provide a promiscuous mode), due to internal incompatibility
with Multiple Function per Port (aka MFP).
The situation that requires this patch is when Physical
Function 0 is the device being used, and it can support SR-IOV
when MFP is enabled, via the driver creating a VEB on an MFP
enabled adapter.
Change-ID: Ie90b00d0d58782a5dfcf2c3c9725a2eb90bd63d8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes use of a pointer called hw consistent
in the i40e_remove function.
Change-ID: Idacc7ff0a09a68289c57457a78618bf5497de077
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to i40e-1.4.13 and i40evf-1.4.9
Change-ID: I9db37f9d4899141c3e5455dfb456d45465b8c035
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new parameters for add_veb allow us to enable and disable VEB stats,
so let's use them.
Update copyright year.
Change-ID: Ie6e68c68e2d1d459e42168eda661051b56bf0a65
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Also update copyright year.
Change-ID: I9acb9160b892ca3146f2f11a88fdcd86be3cadcc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the DCB firmware version related checks specific to
X710 and XL710 only. These checks are not required for
X722 family of devices.
Introduced an inline routine to help determine if the
MAC type is X710/XL710 or not.
Moved the firmware version related checks in i40e_sw_init()
and defined flags for different cases
Fix the version check to allow using "Set LLDP MIB" AQ
for beyond FVL4 FW releases.
Change-ID: Ib78288343de983aa0354fc28aa36e99b073662c0
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filters function is moved up in the service_task because
it may need to request a reset, and we don't want to wait another round
of service task time.
NOTE: Filters will be replayed by sync_vsi_filters including broadcast
and promiscuous settings.
Also, added some error handling in this space in case any of these
fail the driver will retry correctly.
Also update copyright year.
Change-ID: I23f3d552100baecea69466339f738f27614efd47
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit b499ffb0a2 ("i40e: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 can support automatic rule eviction for automatically added
flow director rules. Feature is (should be) disabled by default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure we check the GENEVE offload capable flag before
we attempt offload.
It also enables the Capability for XL710/X710 devices with FW API
version higher than 1.4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY interrupt mask bits mask out the events we don't want,
so we need to negate the bitmask of events we want.
Change-ID: I273244da5a8d285b6abc84fd68a90f1e6fa0393e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filter function was allocating memory in such
a way that it could sleep (GFP_KERNEL) which was causing a problem
when called by the team driver under rcu_read_lock(), which cannot
be held while sleeping. Found with lockdep.
Change-ID: I4e59053cb5eedcf3d0ca151715be3dc42a94bdd5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missing space in comment, fixed.
Change-ID: I8cdf3ce5994b4a97dcc3eeb33422533918546667
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The probe routine already had a u32 val declared, no need
to do it again. Found by W=2 compile.
Change-ID: Id7b65f6d0ef6bb71067d0557f5be0202b6d8741e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-16
This series contains updates to i40e/i40evf only.
Shannon adds flags to MAC allocation requests to signify that the MAC VLAN
filters should come from the shared resource pool. Added a new "set switch
config" admin queue command and the new Cisco VXLAN-GPE cloud tunnel type
for the admin queue commands. Added more detail to the NVM update debug
message in order to see the full ethtool request data. Also added a few
more bits of netdev data into the debugfs output for dump VSI.
Pandi fixes the width of two datatypes which were being declared a different
size from what they are assigned.
Anjali fixes an issue where we were not doing write-back on interrupt
throttle for legacy case in x722.
Mitch adds a counter for ARQ overflows since sometimes an ever-growing
number indicates that something bad is happening. Also added 20G speed for
Tx bandwidth calculations.
Jesse refactors the DCB function based on a community suggestion to change
the multi-level if statement into a switch statement. Cleans up VF device
IDs in the PF, since it does not need to know them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe routine already has too many locals, just convert one
used for kzalloc into a kcalloc, eliminating the local.
Change-ID: I349049872b71f858cbeb91ad7836e6767fc7b7d1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.
Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add some missing reporting/advertisement of 100Mb capability
for adapters that support it.
Change-ID: I8b8523fbdc99517bec29d90c71b3744db11542ac
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done per ixgbe, use a private workqueue to avoid blocking the
system workqueue. This avoids some strange side effects when
some other entity is depending on the system work queue.
Change-ID: Ic8ba08f5b03696cf638b21afd25fbae7738d55ee
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds another way to access the RSS keys and lut using the AQ
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the KX and QSFP device IDs for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The restart-autoneg work around does not apply to X722.
Added a flag to set it only for the right MAC and right FW version
where the work around should be applied.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Change-ID: I942c3ff40cccd1e56f424b1da776b020fe3c9d2a
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add MAC filter element to the end of the list in the given order,
just to be tidy, and just in case there are ever any ordering issues in
the future.
Change-ID: Idc15276147593ea9393ac72c861f9c7905a791b4
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes following build warnings :
drivers/net/ethernet/intel/i40e/i40e_main.c:7057:13: warning:
'i40e_sync_udp_filters_subtask' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8524:13: warning:
'i40e_add_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8569:13: warning:
'i40e_del_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8604:13: warning:
'i40e_add_geneve_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8651:13: warning:
'i40e_del_geneve_port' defined but not used [-Wunused-function]
Fixes: 6a89902405 ("i40e: geneve tunnel offload support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow an ID that has never been productized is in the
code. There are no plans to use it, so just get
rid of it.
Change-ID: I59117d48ea9ee0360b0fe33833ac8092f8a24b4c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the i40e equivalent of commit c762dff24c ("ixgbe: Look up MAC
address in Open Firmware or IDPROM").
As with that fix, attempt to look up the MAC address in Open Firmware
on systems that support it, and use IDPROM on SPARC if no OF address
is found.
In the case of the i40e there is an assumption that the default mac
address has already been set up as the primary mac filter on probe,
so if this filter is obtained from the Open Firmware or IDPROM, an
explicit write is needed via i40e_aq_mac_address_write() and
i40e_aq_add_macvlan() invocation.
The I40E_FLAG_PF_MAC flag in the platform-private i40e_pf structure
tracks whether a platform-specific mac address was found, in which
case calls to i40e_aq_mac_address_write() and i40e_aq_add_macvlan()
will be triggered.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to geneve_get_rx_port in i40e so that when it
comes up it can learn about the existing geneve tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.
Since these messages are really for debugging purposes, reclassify
them as such.
Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.
Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to i40e and i40evf only.
Mitch updates the i40evf driver by increasing the maximum number of queues,
since future devices will allow for more queue pairs. Cleans up a
duplicate printing of the driver info string done in init, since it is
already done in probe. Cleaned up the several allocations which did
not need to be at atomic level, where GFP_KERNEL would work just fine.
Then makes i40e_sync_vsi_filters() a more mature function, make having
a common exit point so it will properly release the busy lock on the VSI
and propagate errors to the callers. Then does some whitespace
housekeeping in i40evf.
Kiran moves and updates the detection/recovery of transmit queue hang code
to service_task from tx_timeout function. Also fixed memory leak when
users program flow-director filter using ethtool (sideband filter
programming), the cause being the check of 'tx_buffer->skb' was preventing
'raw_buf' from being freed as part of the cleanup.
Jesse enabled the ability to turn off/on packet split using ethtool priv
flags. Then does some housekeeping for both the i40e and i40evf drivers
which includes: remove unused/useless code, correct whitespace, remove
duplicate #include, fix incorrect comment, etc...
Neerav cleans up functions to gather Flow Control Rx XOFF stats, since
the recent change in the driver logic for checking transmit hang has been
moved, so these functions do not do anything meaningful any longer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fd89545f3 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separate functions to gather Flow control Rx XOFF stats was to
determine if the Tx for a queue was paused due to Link Flow Control(LFC)
or Priority Flow Control(PFC).
But, with recent change in the i40e driver the logic for checking th Tx
hang has been removed and these functions don't do anything meaningful.
Hence, there is no need to keep these separate functions to gather Rx
XOFF stats for LFC or PFC.
This patch removes these functions and moves the stat collection for
XOFF Rx to the i40e_update_pf_stats() that collects all the PF stats.
Change-ID: Iec1452dac3a6766f0d968e754cb407530d7c60cd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of having our own custom symbol, we can just rely
on whether or not the kernel has the feature enabled.
In this case use IS_ENABLED(CONFIG_VXLAN) in order to handle
built-in or module in the current BKM way.
Change-ID: I5890fbb518ff8ed6bb07c3362fb0a8a829f9b241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains following changes:
- detection and recovery logic (issue SW interrupt) has been moved to
service_task from timeout function.
- added some more debug info from tx_timeout.
Logic to detect and recover TX queue hung is now two step process:
- service_task detects TX queue hung and sets a bit(hung_detected) if
it was not set.
- if bit was set (means this is back-back hung condition detected),
issue SW interrupt and clear the bit.
- napi_poll clears the bit unconditionally since it cleans TX/RX queues.
Change-ID: Ieed03a48927c845a988b3ff375090bf37caeb903
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the confusing kernel message of enabled RSS size,
by reporting it together with the hardware maximum RSS size.
Change-ID: I64864dbfbc13beccc180a7871680def1f3d5a339
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Change-ID: I73886469dca9e9f6b16d842182a87f3f4009f95d
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the old pf-specific function in order to clarify
its scope. This patch also creates a more generic configure RSS
function with the old name.
This patch also creates a new more generic function to get RSS
configuration, using the appropriate method.
Change-ID: Ieddca2707b708ef19f1ebccdfd03a0a0cd63d3af
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust the RSS configure functions so that there is a generic way to
hook to ethtool hooks.
Change-ID: If446e34fcfaf1bc3320d9d319829a095b5976e67
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The watchdog only calls link_event not handle_link_event which means
that we need to save the old information in link_event.
Previously when polling we were comparing current data to the old data
saved the last time we actually received a link event. This means that
the polling would only fix link status changes in one direction
depending on what the last old data saved off was.
Change-ID: Ie590f30fdbcb133d0ddad4e07e3eb1aad58255b3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's really no reason to kill the kernel thread just because of a
little info string. This reworks the code to use snprintf's limiting to
assure that the string is never too long, and WARN_ON to still put out
a warning that we might want to look at the feature list length.
Prompted by a recent Linus diatribe.
Change-ID: If52ba5ca1c2344d8bf454a31bbb805eb5d2c5802
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the thread and eventually the kernel in this
case. In fact, the remainder of the code won't hurt anything anyway,
so just complain that we're here and move along.
Prompted by a recent Linus diatribe.
Change-ID: Iec020d8bcfedffc1cd2553cc6905fd915bb3e670
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up the version...
Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem of possibly getting inconsistent flow control
statuses after a PF reset. Requested_mode was being set with a default
value during probing, but the initial HW state could be different from
this mode.
Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually
in VEB mode before allowing LB in the add VSI routine, instead of
unconditionally returning VEB bridge mode.
Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send flow control frames if flow
control is enabled.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was printing a message about not being able
to assign VMDq because of a lack of MSI-X vectors.
This was because a line was missing that initialized a variable,
simply a merge error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-19
This series contains updates to i40e and i40evf only.
Kiran adds a spinlock around code accessing VSI MAC filter list to
ensure that we are synchronizing access to the filter list, otherwise
we can end up with multiple accesses at the same time which can cause
the VSI MAC filter list to get in an unstable or corrupted state.
Jesse fixes overlong BIT defines, where the RSS enabling call were
mistakenly missed. Also fixes a bug where the enable function was
enabling the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx, while refactoring the IRQ
enable function to simplify reading the flow. Addressed the high
CPU utilization of some small streaming workloads that the driver should
reduce CPU in.
Anjali fixes two X722 issues with respect to EEPROM checksum verify and
reading NVM version info. Fixed where a mask value was accidentally
replaced with a bit mask causing Flow Director sideband to be broken.
Alex Duyck fixes areas of the drivers which run from hard interrupt
context or with interrupts already disabled in netpoll, so use
napi_schedule_irqoff() instead of napi_schedule().
Mitch fixes the VF drivers to not easily give up when it is not able
to communicate with the PF driver.
Carolyn fixes a problem where our tools MAC loopback test, after driver
unbind would fail because the hardware was configured for multiqueue and
unbind operation did not clear this configuration. Also fixed a issue
where the NVMUpdate tool gets bad data from the PHY when using the PHY
NVM feature because of contention on the MDIO interface from getting
PHY capability calls from the driver during regular operations.
Catherine fixed an issue where we were checking if autoneg was allowed
to change before checking if autoneg was changing, these checks need to
be in the reverse order.
Jean Sacren fixes up an function header comment to align the kernel-docs
with the actual code.
v2: Cleaned up the use of spin_is_locked() in patch 1 based on feedback
from David Miller, since it always evaluates to zero on uni-processor
builds
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
'err' would be overwritten immediately, so we should declare it only
rather than initialize it to zero.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The second argument name in the kernel-doc argument list for
i40e_features_check() was slightly off. Fix it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where our Tools MAC Loopback test, after
driver unbind would fail. This was because the hw was configured
for multiqueue and unbind operation did not clear this configuration.
The problem is fixed by resetting this configuration in i40e_remove.
Change-ID: I130c05138319182ed1476d3a0b5222d6a6320af9
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.
This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.
In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.
Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save a little stack space and remove unnecessary strncpy() with a little
string pointer.
Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.
Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though the device might be in MFP mode, if there's only one partition
enabled, then we still have plenty of interrupts for managing the Flow
Directory Sideband activity. This patch enables FD SB in this case.
This patch also reverses the sense of the conditional in order to remove
the negative logic.
Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This version check only applies to very, very old firmware,
that only ran on A0 hardware, which we never shipped and don't
support in this driver anyway. Remove it, before somebody
gets hurt.
Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several error messages that have been printing when there is
no functional issue. These messages should be available at debug message
level only.
Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add nlflags to the function comment for ndo_bridge_setlink.
Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.
Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.
When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.
Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.
Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.
Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
