To make the picture complete, add DTS entries also for the
second and fourth MMC/SD blocks on the MSM8660. SDC2 is
an 8-bit interface and SDC4 is a 4-bit interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Without this patch (and with CONFIG_QCOM_ADSP_PIL), I get this error:
[ 0.711529] qcom_adsp_pil adsp-pil: failed to get xo clock
[ 0.711540] remoteproc remoteproc0: releasing adsp-pil
With this patch, adsp-pil can initialize correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial set of CoreSight components found on Qualcomm
msm8974 and apq8074 based platforms, including the APQ8074
Dragonboard board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Rock 2 square board has a USB -> SATA converter hooked up to its usb
host1 connection. Enable the usb controller and always turn on the power
on the 5V sata power connector (controlled by gpio).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All three devices provide GPIO based LEDs named power,
wlan and app.
Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a typo, it should be GPIO176 and not GPIO106.
And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.
Fixes: 0d4cb3ccee ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 84e734f497 ("ARM: dts: silk: add DU DT support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 876e7fb9f4 ("ARM: shmobile: r8a7794: alt: Enable VGA port")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 46c4f13d04 ("ARM: shmobile: r8a7794: Add DU node to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing module clock for the second channel of the display unit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi One features a MicroUSB port that can work in both host mode
and peripheral mode.
When in host mode, its VBUS is controlled via a GPIO; when in peripheral
mode, its VBUS cannot be used to power up the board.
Add support for this port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.
This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes the status of AC power supply.
This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.
This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PCIe bridges should have a node name of 'pcie'.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
The Cortina Gemini has an internal PCI root bus, add this to
the device tree, and add interrupt mapping (swizzling) to the
relevant systems device trees.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
-----BEGIN PGP SIGNATURE-----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=bTSQ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=cLA3
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2017-03-21' into devicetree/next
This pull request brings in the DT nodes for enabling HDMI audio on
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=CKev
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though cpsw doesn't support EEE feature, Atheros 8035 provides
automatic EEE support that is enabled by default. This causes
occasional link drops when link partner also announces EEE support.
These link drops occur on both 100Mbit/s and 1000Mbit/s speeds.
So disable EEE advertising completely.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch lists STM32F7's RCC numeric constants.
It will be used by clock and reset drivers, and DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch enables clocks for STM32F746 MCU.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add appropriate properties to devices in the Linksys WRT AC Series for the
mvneta driver to use hardware buffer management.
Also update "soc" ranges property and set the status of bm and bm-bppi
to "okay" (SRAM).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[include rename in rk1108.dtsi to prevent compile errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.
Let's add a configuration for the HCI so the modems can be enabled.
Note that the modems still need additional GPIO based configuration.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The binding should state "cortina,gemini-gpio", "faraday,ftgpio010"
stating the full name of the IP part.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cA1
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix USB host for sama5d2
- Fix cpuidle on sama5
-----BEGIN PGP SIGNATURE-----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=XXBm
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of device tree fixes for various boards / SoCs.
-----BEGIN PGP SIGNATURE-----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=fo5j
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYz5T0AAoJEFBXWFqHsHzOiUwH/1S1b6Si8fbG0g11BQm+2N0u
mHf3Z41f+F81xuFFt/6ZX5ICiOXDlAdcga3QXUCNCWfYnFLJyDSoF6Z1JSUkGeEa
kVCmi+WWUOYtyU7QYfaBzPtZqqUurqwBu8WwOO/IW81yKpNMNflATKYreutki2oI
z3BW3WGlOEJXIJeyea3EjTClQLhP0qdEn08StneHUdA+YS9nd6/jreHhta4r7gQs
Z4B2yBap7P4a5glOzCafuIAdpPscKS096ND1k3APsiJPGaNjYtxhig5MGo89LK7e
JNfw1KroAmifGVmrgDVwKI3MFLrvSh74phFXwnIAX5iK2U2wB/fiMQjVKmvY9tw=
=NSw6
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The highest supported frequency (1.2GHz) requires to "overvolt" the CPU.
However, some boards still do not have the cpu-supply DT property in the
cpu DT node which means that the CPU will always run with the same input
voltage but try to run at 1.2GHz frequency. This is the source of
(experienced) CPU crashes.
Remove the OPP which requires overvolting the CPU until all boards have
a cpu-supply property.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The digital AIF interfaces has been renamed in the sun8i audio codec
driver so the audio-routing in the device tree must be renamed too.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the Gemini power controller to the SoC DTSI
file.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds crypto hardware (SPU) to Northstar Plus device tree file.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adds mailbox / PDC to NSP device tree. Needs new compatibility string
to differentiate from NS2 version.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding ethernet aliases. These are used, for example, by bootloaders,
to modify the MAC addresses in the device tree.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47081A0 based home router with BCM43217 and BCM4352 wireless
chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c device tree entry should be disabled by default to match the
current convention in other device tree files. Similarily, enable it on
the XMC board, where it is being used.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C support to the bcm5301x Device Tree. Since no driver changes
are needed to enable this hardware, only the device tree changes are
required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM TWD Watchdog to the bcm5301x device tree. The
ARM TWD timer allocated the register space for the WDT, so this patch
necessitated shrinking that. Also, the GIC masks were added for these.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that early-bresp-disable and full-line-zero-disable are required
because the sideband signals between the CPU and L2C were not connected
in this SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the dmas and dma-names properties to support HDMI audio.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the Altera Arria10 System Resource Reset Controller to the MFD
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2 change commit header to ARM: dts: socfpga.
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3228/rk3229.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3066/rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3036.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
-----BEGIN PGP SIGNATURE-----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=svZk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.11-rc cycle:
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
* tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
ARM: OMAP5 / DRA7: Fix HYP mode boot for thumb2 build
ARM: OMAP3: Fix smartreflex platform data regression
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
-----BEGIN PGP SIGNATURE-----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=0Qzy
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.11,
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
* tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Watchdog module does not have external dependencies so it can be safely
enabled in exynos4.dtsi thus making it available for all Exynos4-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Watchdog module does not have external dependencies so it can be safely
enabled in s3c64xx.dtsi thus making it available for all S3C64xx-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The Exynos4412 has the same watchdog as newer SoCs (e.g. Exynos5250).
Just like the others, for working it requires additional steps in Power
Management Unit: unmasking the reset request and enabling the system
reset. Without these additional steps in PMU, the watchdog will not be
able to reset the system on expiration event.
Change the compatible of Exynos4412 watchdog device node to
samsung,exynos5250-wdt which includes the additional PMU steps.
This will also fix infinite watchdog interrupt in soft mode (lack of
interrupt clear) because it is also included in samsung,exynos5250-wdt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7793.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pcie_bus_clk device node is already enabled in r8a7791.dtsi, so
there is no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7790.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7779.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7778.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While status "ok" does work, the canonical form is "okay", so update the
few places that used the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd222.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd111.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-rut1xx.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-nas4220b.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference &gpio1.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree for the Gemini SoC and the ITian
Square One SQ201 board that has been my testing target
for Gemini device tree support.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The eMMC devices on UniPhier boards are generally used in the 8-bit
mode. So, DAT4-7 pins should be controlled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These UniPhier DT files are fine as long as they are compiled in the
Linux build system. It is true that Linux is the biggest user of
DT, but DT is project neutral from its concept. DT files are often
re-used for other projects. Especially for the UniPhier platform,
these DT files are re-used for U-Boot as well.
If I feed these DT files to the FDTGREP tool in U-Boot, it complains
about the node order.
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Given that DT is not very sensitive to the order of nodes, this is a
problem of FDTGREP. I filed a bug report a year ago, but it has not
been fixed yet.
Differentiating DT is painful. So, I am up-streaming the requirement
from the down-stream project.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock and the C4 power domain,
so it can be power managed using that clock in the future.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog timer support for RZ/A1.
For the RZ/A1, the only way to do a reset is to overflow the WDT, so this
is useful even if you don't need the watchdog functionality.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
According to phy datasheet, 25ms are sufficient. This also reduces
the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch renames mmc2_sck_cfg in order to prepare for an alternative
muxing setup.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).
But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."
, so limit the TVDAC analog power supply as suggested.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an onboard Wolfson wm8731 codec which is muxed
to the ssi2 controller. Unlike most (all?) supported i.MX6 board/codec
combinations the wm8731 is operated in slave mode and the clock setup
is static.
Add support for it.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhanced commit message, ported
to upstream and some cleanup]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc76 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Marvell 98dx3236 SoC only has a single PCIe x1 interface. The "Port
0.1 MEM" range was errantly kept when creating a specific dts for the
SoC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Previously the coreclk binding for the 98dx3236 SoC was inherited from
the armada-370/xp. This block is present in as much as it is possible to
read from the register location without causing any harm. However the
actual sampled at reset values are reflected in the DFX block.
Moving the binding to the DFX block enables support for different clock
strapping options in hardware.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell datasheets refer to the integrated CPU as "Armada-XP". In
reality there are a number of differences to the actual Armada-XP so
rather than including armada-xp.dtsi and disabling many of the IP
blocks. Include armada-370-xp.dtsi and add the required nodes.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Rather than having a separate node for the dfx server add a reg property
to the parent node. This give some compatibility with the Marvell
supplied SDK.
As no upstream driver currently exists for this block and support for
this SoC is still quite fresh in the kernel it should not be necessary
to retain a backwards compatible binding.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In others board we have the sata led set to function
with the sata led trigger by default.
This patch makes the same for these board that have sata
led but get disabled by not associating it to any trigger.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The mbus binding had been extended more than two years ago, but the
device tree files for Armada 38x didn't change.
Adding this third entry will allow the mbus going to suspend which was
the last thing preventing the SoC going to standby mode
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900ACS (Shelby) is another Armada 385 based router in
the Linksys WRT AC Series which got released in October 2015.
The file armada-385-linksys-shelby.dts is taken from OpenWrt as-is and
originally authored by Imre Kaloz.
URL: 8466384db1/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-shelby.dts
CC: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the burst and esc clock frequency properties to the parent (DSI node).
Currently the clock is parsed from the port node, while it should be
taken from the dsi node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In Odroid XU3 Lite board, the temperature levels reported for thermal
zone 0 were weird. In warm room:
/sys/class/thermal/thermal_zone0/temp:32000
/sys/class/thermal/thermal_zone1/temp:51000
/sys/class/thermal/thermal_zone2/temp:55000
/sys/class/thermal/thermal_zone3/temp:54000
/sys/class/thermal/thermal_zone4/temp:51000
Sometimes after booting the value was even equal to ambient temperature
which is highly unlikely to be a real temperature of sensor in SoC.
The thermal sensor's calibration (trimming) is based on fused values.
In case of the board above, the fused values are: 35, 52, 43, 58 and 43
(corresponding to each TMU device). However driver defined a minimum value
for fused data as 40 and for smaller values it was using a hard-coded 55
instead. This lead to mapping data from sensor to wrong temperatures
for thermal zone 0.
Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
do not impose any limits on fused values. Since we do not have any
knowledge about these limits, use 0 as a minimum accepted fused value.
This should essentially allow accepting any reasonable fused value thus
behaving like vendor driver.
The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
exynos4412 with one change - the samsung,tmu_min_efuse_value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Add pcie-phy node to phy-exynos-pcie along with some changes to other
nodes:
1. Remove the configuration space from "ranges" property because this
was the old way of getting it. Preferred is to use "config" reg.
2. Use the reg-names as "elbi" and "config" so the purpose of addresses
will be easily known.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit adds the device tree description for the Synology DS116 NAS.
It is a one-bay NAS powered by a Marvell Armada 385 at 1.866 GHz. The
device features the following items :
- 1 GB DDR3 RAM
- a 8MB SPI flash
- 2 USB3 ports, power-controlled via a GPIO for each
- 1 gigabit ethernet interface connected over SGMII to a 88e1514 phy
- a single SATA port, power-controlled via a GPIO
- a battery-powered RTC
- one UART connected to the serial console (2mm connector on board)
- the Tx line of the second UART connected to a PIC microcontroller
dealing with beep, reset, power-off and LED blinking (9600 Bps)
- some of the front-panel LEDs are connected to GPIOs, one is directly
connected to the SATA link to report disk activity.
- a GPIO-controlled fan (3 bits for 7 speeds and OFF)
With this DTS, my NAS is 100% functional starting with kernel 4.9.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As was done with Armada XP, add node labels to Armada 38x common and SoC
specific nodes to make them easier to reference in board device trees.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.
Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the vpif node with an output port with a single channel.
NOTE: this is still mostly just hardware description - the actual
driver is registered using pdata-quirks. We need the node however
for correct pin control function selection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need the expander to be probed to allow the VPIF controller to
receive interrupts from the video decoder.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new pinctrl sub-node for vpif display pins. Move VP_CLKIN3 and
VP_CLKIN2 to the display node where they actually belong (vide section
36.2.2 of the OMAP-L138 technical reference manual).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The da850-evm dts file contains whitespace errors in the vpif node.
This patch fixes them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a device tree node for sound on LEGO MINDSTORMS EV3. The EV3
uses one of the SoC PWMs connected to an amplifier to create sound from
a speaker.
The PWM is passed through a low-pass filter, so it is actually possible
to do PCM playback, but there is no existing driver, so just using
pwm-beeper for now, since it is also a compatible mode of operation.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a node for the TI ADS7957 analog/digital converter on LEGO
MINDSTORMS EV3 as well as a regulator node that is used by the A/DC node.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: 34ea4b4a82 ("ARM: dts: r8a7794: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: ad53f5f00b ("ARM: dts: r8a7793: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 6f9314ce25 ("ARM: dts: r8a7791: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: 2c3de36700 ("ARM: dts: r8a7790: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A7 cache controller is an integrated controller, and thus the
device node representing it should not have a unit-addresses or reg
property.
Fixes: c95360247b ("ARM: dts: r8a7745: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 34e8d993a6 ("ARM: dts: r8a7743: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15/A7 cache controllers are integrated controllers, and thus
the device nodes representing them should not have unit-addresses or reg
properties.
Fixes: b0da45c60d ("ARM: dts: r8a73a4: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dual Cortex-A9 MPCore inside socfpga has a standard PMU unit for
each core mapped in the DAP memory space. Add support for it!
Tested with perf on a Cyclone 5 SoC DK.
Reported-by: Alberto Dassatti <alberto.dassatti@heig-vd.ch>
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Tested-by: Alberto Dassatti <alberto.dassatti@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This makes it easier to reference the CPU nodes afterwards.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The skeleton.dtsi file is now deprecated as noted in commit 9c0da3cc61
("ARM: dts: explicitly mark skeleton.dtsi as deprecated"). The SoCFPGA
device trees already contain the nodes that are defined in skeleton.dtsi
(#address-cells, #size-cells, chosen, aliases, memory).
Including skeleton.dtsi is useless and will produce the following
warning when compiled with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
GPIO LEDs in the Cyclone5 EBV SOCrates board have a unit name but no reg
property. Indeed, GPIO LEDs do not need such a property. They do not
need a unit name neither. This will trigger the following warnings when
compiled with W=1:
Node /gpio-leds/led@0 has a unit name, but no reg property
Node /gpio-leds/led@1 has a unit name, but no reg property
Node /gpio-leds/led@2 has a unit name, but no reg property
The solution is to remove the unit name. In order to have unique node
names, a rename is necessary. This should be harmless as all the LEDs
have a 'label' property, hence their name do not derive from the node
name and will stay the same after this patch.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The stmpe_touchscreen node in Cyclone5 MCV EVK has a reg property, but
this is not used by the driver. Moreover the binding documentation do
not define this property. Having a reg property without a unit name will
trigger the following warning when compiled with W=1:
Node /soc/i2c@ffc04000/stmpe811@41/stmpe_touchscreen has a reg or ranges
property, but no unit name
Remove the superfluous reg property.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Node eccmgr has a unit name, but do not have a reg property as only the
child nodes do have this property. Likewise the usbphy node do not have
a reg property. This will trigger the following warnings when compiled
with W=1:
Node /soc/eccmgr@ffd08140 has a unit name, but no reg property
Node /soc/usbphy@0 has a unit name, but no reg property
Remove the superfluous unit names.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Memory nodes in Arria5, Cyclone5 and Arria10 do not have a unit name.
This will trigger several warnings like this one (when compiled with
W=1):
Node /memory has a reg or ranges property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Most clock nodes in Arria5, Cyclone5 and Arria10 have a reg property but
does not have a unit name. This will trigger several warnings like this
one (when compiled with W=1):
Node /soc/clkmgr@ffd04000/clocks/periph_pll has a reg or ranges
property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Fix warnings reported when built with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") declared that skeleton.dtsi was deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added two WAN status LEDs and a GPIO key for brightness which were
missing.
Signed-off-by: Aditya Xavier <adityaxavier@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's preferred to have DT source files licensed under BSD compatible
license. All new BCM5301X DTS files use ISC so let's also relicense old
ones to it.
Except for me only Hauke was ever touched these files in his commit
9faa5960ee ("ARM: BCM5301X: add NAND flash chip description") and
commit bb1d8fba19 ("ARM: BCM5301X: add NAND flash chip description for
Asus RT-AC87U").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Droid4's touchscreen can be used with mainline's maxtouch driver. The
touchscreen's lower area is used for four soft buttons (KEY_MENU,
KEY_HOME, KEY_BACK, KEY_SEARCH), but that does not seem to be currently
supported by the mainline kernel.
The mxt224 configuration can be saved with "mxt-app" for the kernel
to load. It can be saved after the first boot with:
# mxt-app -d i2c-dev:1-004a --save /lib/firmware/maxtouch.cfg
Where the mxt-app can be found at:
https://github.com/atmel-maxtouch/mxt-app
The firmware for the droid 4 mxt224 comes with GPLv2 license in the
Motorola Linux kernel sources. This firmware can be dumped out with
"droid4-touchscreen-firmware" program at:
https://github.com/tmlind/droid4-touchscreen-firmware
The related LCD patches are still pending, but when merged,
the touchscreen can be rotated in X with something like:
# xrandr --output DSI-1 --rotate right
# xinput set-prop 6 'Coordinate Transformation Matrix' \
0 1 0 -1 0 1 0 0 1
For now, we rely on a gpio-hog but later on we can add the reset
gpio handling to the driver and have it load the maxtouch.cfg and
maxtouch.fw on boot.
This patch is based on combined similar patches done by me and
Sebastian.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Droid 4 "Volume Down" and "Keypad Slide" keys are
connected via SoC GPIOs, "Power Key" via CPCAP and
all other keys via SoC keypad Matrix. This adds the
GPIO keys.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: updated to apply on omap4-keypad patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With drivers/mfd/motorola-cpcap.c and drivers/regulator/cpcap-regulator.c
we can now configure proper regulators for droid 4.
Let's add regulator voltages and switch over MMC, eMMC and WLAN to use
the CPCAP regulators.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some SPI nodes are missing #address-cells and #size-cells. This is
causing warning at device tree compilation when some SPI device
sub-nodes are defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS") started
the migration from ARCH_SHMOBILE_MULTI to ARCH_RENESAS.
Update the Makefile to build DTBs for Renesas platforms to use the new
symbol, and move the Renesas section to preserve sort order.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SDHI controller in the RZ/A1 has 2 clock sources per channel and both
need to be enabled/disabled for proper operation. This fixes the fact that
the define for R7S72100_CLK_SDHI1 was not correct to begin with (typo), and
that all 4 clock sources need to be defined an used.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Mali clock rate was improperly assumed to be 408MHz, while it was
really 384Mhz, 408MHz being the "extreme" frequency, and definitely not
stable.
Switch for the stable, correct frequency for the GPU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mali GPU in the A33 has various operating frequencies used in the
Allwinner BSP.
Add them to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the needed node for DFVS on Sinovoip BPI-M2.
This add the axp221 under the p2wi node, the regulators and
the cpu-supply property for cpu0.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Beelink X2 has an on-board eMMC so add a node enabling
the mmc2 controller.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20-OLinuXino-Micro has 3.5 mm sockets for headphone output and
microphone input.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the GR8 DTSI is duplicated with the common sun5i DTSI, and some of
the extra nodes defined there actually apply to all of the sun5i family.
Move those into the common DTSI so that all SoCs can benefit from it, and
include the sun5i DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the R8 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the A10s DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some controllers found in the A13 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UART3 pin group for the CTS and RTS signals doesn't follow our usual
pattern. Rename it so that it matches.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There's one UART2 pin group that can be used across all sun5i SoCs.
However, the A10s already has one pin group for that controller.
Change the index of the one in the A10s DTSI, and add the common one to
sun5i.dtsi
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Of the three simple framebuffer setups we have in the A10s, two of them can
be shared with the other SoCs from the sun5i family (LCD panel and
composite output).
However, the only one we cannot share is the HDMI, which is the first
listed in the A10s DTSI. In order to make it more logical and so that we
can share the framebuffer nodes in the common DTSI, reorder those nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
One of the pins group for the EMAC can be used by all the SoCs of the sun5i
family, and as such can be moved to the common DTSI.
Unfortunately, this group is the second one we declare in our DT for now.
Make it the first one so that it's more logical and consistent with the
rest of our DTs before moving it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Let's configure the keypad in a way where it's usable out of the
box for Linux console use. We want to have the keyboard usable with
Linux console for example when stuck into an initramfs during boot,
for when installing a distro.
As we need to need to have keys mapped in the user space anyways
for some of the keys to match the labels, this non-standard mapping
or usability should be OK.
Some keys don't match the labels either as they don't follow the PC
keyboard style. For example we have "shift + ," produce "<", and
"shift + ." produce ">" instead of ";" and ":".
So let's follow the standard PC keyboard layout for ctrl, shift and
alt keys:
Ctrl = what is labeled as shift
Alt = what is labeled as SYM
Shift = what is lableled as caps lock
This way we have Ctrl key for console use. Who knows where they got
the caps lock idea.. Probably from some focus group popularity vote
or something.
For the OK key, let's keep it as the useless KEY_OK unless we can
come up with some standard mapping for it we can stick with.
We have at least Esc, Delete, Meta, and Page Down keys missing, but
none of them seem to be better than others. PC keyboard often has
Page Down in that location. Esc would be probably the most usable
one when installing a Linux distro but is the opposite of OK.
Note that the LCD keys are just touchscreen hot spots, so I'm not
sure if the driver or hardware allows setting them up as keys for
the console.
Anyways, the rest can be mapped in the user space.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
with this patch.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MiQi board's green LED doesn't work at all with the mainline kernel.
There are multiple reasons to this. First, the gpio number is wrong, it
is declared on gpio220 (chip 7 pin 4) instead of gpio218 (chip 7 pin 2).
Second, a pinctrl is referenced, also declared with the same wrong value
while it is not unused. Third, the GPIO polarity was wrong (active low
instead of active high) with the default value set to "default-on",
resulting in the LED being turned off even when the GPIO is correct.
This patch fixes all these inconsistencies at once since these they are
related to each other, and also restores the "timer" trigger which is
the same as the one used by the kernels shipped with the board.
It's important to note that during the port to mainline, the led's label
was changed from "System" to "miqi:green:user", so scripts making use of
the name will still not work until they're fixed.
Fixes: b1a76f75d76e ("ARM: dts: rockchip: add MiQi board from mqmaker")
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds the DT definition of the es8388 i2c device
found at address 0x10. It also adds the definition for connecting
the Rockchip I2S to the es8388 analog output.
This commit is based on the initial work that was done by Sjoerd Simons
<sjoerd.simons@collabora.com> with some improvements.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Memory starts at 0x80000000, not 0. 0 "works" due to mirrior of the
first 128M of RAM to that address. Anything greater than 128M will
quickly find nothing there. Correcting the starting address has
everything working again.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 7eb05f6d ("ARM: dts: bcm5301x: Add BCM SVK DT files")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The UARTs are outputting garbage on the console. This is due to a speed
issue. We can simply use the clock speed (which is now defined in the
DTSI file) and everything works fine.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: cdc36b22 ("ARM: dts: enable clock support for BCM5301X")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's connected to a GPIO pin of an extra controller placed on the PCIe
card.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tenda AC9 has PCIe controller with just one device connected to it:
0000:00:00.0 14e4:d145 Bridge Device
└─ 0000:01:00.0 14e4:a8db Network Controller
This card is directly on SoC (doesn't use physical connector) and has
BCM43217 chipset with bcma bus. One of its components is ChipCommon core
which is also a GPIO controller. We need to describe it to be able to
add devices using its GPIO pins.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Initial version of DTS to support Broadcom BCM953012HR Northstar
HR platform, similar to, but not the same as existing 953012K.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It
uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The iproc-qspi driver is the SPI driver that should be used going
forward. Modify the SPI DT entry to use this driver, and add an entry
in the bcm953012k DTS file to enable the SPI.
Tested on the bcm953012k board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the NAND entry in the DTS for the bcm953012k reference board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's wireless home router based on BCM4708A0 with BCM4360 + BCM43217
wireless chipsets. LEDs will be hopefully added later to the DT.
According to some sources it may use the same board as EA6400 and just
differ by an original vendor firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's tri-band wireless home router based on BCM4709A0 with 3 x BCM43602
chipsets. LEDs will be hopefully added later to the DT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Let's define the SPI controllers in the Aspeed SoCs AST2500 and
AST2400 and also enable these, as well as the chips, on the associated
platforms.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This reverts commit cab4328268 ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab4328268 ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The A13 hardware line is shared by SPI and MCI1 controller.This patch
disables the SPI controller so that the MCI1 (the big MMC card slot) can
be used.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The matrix node was defined before the documentation for the bus
matrix configuration was submitted. Patch the device tree to match
the DT doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
SFRBU, the Special Function Registers Backup manage specific aspects of the
integrated memory, bridge implementations, processor and other
functionality not controlled elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
