This patch adds following attributes to watchdog device's sysfs interface
to read its different status.
* state - reads whether device is active or not
* identity - reads Watchdog device's identity string.
* timeout - reads current timeout.
* timeleft - reads timeleft before watchdog generates a reset
* bootstatus - reads status of the watchdog device at boot
* status - reads watchdog device's internal status bits
* nowayout - reads whether nowayout feature was set or not
Testing with iTCO_wdt:
# cd /sys/class/watchdog/watchdog1/
# ls
bootstatus dev device identity nowayout power state
subsystem timeleft timeout uevent
# cat identity
iTCO_wdt
# cat timeout
30
# cat state
inactive
# echo > /dev/watchdog1
# cat timeleft
26
# cat state
active
# cat bootstatus
0
# cat nowayout
0
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We need few sysfs attributes to know different status of a watchdog device.
To do that, we need to associate .dev_groups with watchdog_class. So
convert it from pointer to static.
Putting this static struct in watchdog_dev.c, so that static device
attributes defined in that file can be attached to it.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix off-by-one error in opal_mce_check_early_recovery() when checking
whether the NIP falls within OPAL space.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few of the config prompts for powerpc self-tests have periods at the
end, which is inconsistent with the rest of the prompts. Remove the
periods.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only delay opal_rtc_read() when busy and are going to retry.
This has the advantage of possibly saving a massive 10ms off booting!
Kudos to Stewart for noticing.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On BMC machines, console output is controlled by the OPAL firmware and is
only flushed when its pollers are called. When the kernel is in a panic
state, it no longer calls these pollers and thus console output does not
completely flush, causing some output from the panic to be lost.
Output is only actually lost when the kernel is configured to not power off
or reboot after panic (i.e. CONFIG_PANIC_TIMEOUT is set to 0) since OPAL
flushes the console buffer as part of its power down routines. Before this
patch, however, only partial output would be printed during the timeout wait.
This patch adds a new kmsg_dumper which gets called at panic time to ensure
panic output is not lost. It accomplishes this by calling OPAL_CONSOLE_FLUSH
in the OPAL API, and if that is not available, the pollers are called enough
times to (hopefully) completely flush the buffer.
The flushing mechanism will only affect output printed at and before the
kmsg_dump call in kernel/panic.c:panic(). As such, the "end Kernel panic"
message may still be truncated as follows:
>Call Trace:
>[c000000f1f603b00] [c0000000008e9458] dump_stack+0x90/0xbc (unreliable)
>[c000000f1f603b30] [c0000000008e7e78] panic+0xf8/0x2c4
>[c000000f1f603bc0] [c000000000be4860] mount_block_root+0x288/0x33c
>[c000000f1f603c80] [c000000000be4d14] prepare_namespace+0x1f4/0x254
>[c000000f1f603d00] [c000000000be43e8] kernel_init_freeable+0x318/0x350
>[c000000f1f603dc0] [c00000000000bd74] kernel_init+0x24/0x130
>[c000000f1f603e30] [c0000000000095b0] ret_from_kernel_thread+0x5c/0xac
>---[ end Kernel panic - not
This functionality is implemented as a kmsg_dumper as it seems to be the
most sensible way to introduce platform-specific functionality to the
panic function.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we copy the whole mm_context_t to the paca but only access a
few bits of it. This is wasteful of space paca and also takes quite
some time in the hot path of context switching.
This patch pulls in only the required bits from the mm_context_t to
the paca and on context switch, copies only those.
Benchmarking this (On top of Anton's recent MSR context switching
changes [1]) using processes and yield shows an improvement of almost
3% on POWER8:
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield --process 0 0
1. https://lists.ozlabs.org/pipermail/linuxppc-dev/2015-October/135700.html
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Rename paca fields to be mm_ctx_foo rather than context_foo]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix a thermal management issue introduced by an ACPI processor
driver change made during the 4.3 development cycle that failed
to return 0 from a function on success which triggered an error
cleanup path every time it had been called that deleted useful
data structures created previously (Srinivas Pandruvada).
- Fix a variable data type issue in the arm_big_little cpufreq
driver's SCPI support code added recently that prevents error
handling in there from working correctly (Dan Carpenter).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=s+R5
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix an ACPI processor driver regression introduced during the
4.3 cycle and a mistake in the recently added SCPI support in the
arm_big_little cpufreq driver.
Specifics:
- Fix a thermal management issue introduced by an ACPI processor
driver change made during the 4.3 development cycle that failed to
return 0 from a function on success which triggered an error
cleanup path every time it had been called that deleted useful data
structures created previously (Srinivas Pandruvada).
- Fix a variable data type issue in the arm_big_little cpufreq
driver's SCPI support code added recently that prevents error
handling in there from working correctly (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi-cpufreq: signedness bug in scpi_get_dvfs_info()
ACPI / processor: Fix thermal cooling device regression
Fix a regression which causes reshape to not start properly
sometimes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=koo+
-----END PGP SIGNATURE-----
Merge tag 'md/4.4-rc6-fix' of git://neil.brown.name/md
Pull md bugfix from Neil Brown:
"One more md fix for 4.4-rc
Fix a regression which causes reshape to not start properly sometimes"
* tag 'md/4.4-rc6-fix' of git://neil.brown.name/md:
md: remove check for MD_RECOVERY_NEEDED in action_store.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=84oS
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs
Pull UBI bug fixes from Richard Weinberger:
"This contains four bug fixes for UBI"
* tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs:
mtd: ubi: don't leak e if schedule_erase() fails
mtd: ubi: fixup error correction in do_sync_erase()
UBI: fix use of "VID" vs. "EC" in header self-check
UBI: fix return error code
with ftrace enabled. With some investigation it was discovered that it
was his compile setup. He was using ccache with hard links, which allowed
recordmcount to process the same .o twice. When this happens, recordmcount
will detect that it was already done and give a warning about it.
Russell fixed this by having recordmcount detect that the object file
has more than one hard link, and if it does, it unlinks the object file
after it maps it and processes then. This appears to fix the issue.
As you did not like the fact that recordmcount modified the file in place
and thought that it should do the modifications in memory and then write
it out to disk and move it over the old file to prevent other more subtle
issues like the one above, a second patch is added on top of Russell's to
do just that. Luckily the original code had write and lseek wrappers that
I was able to modify to not do inplace writes, but simply keep track
of the changes made in memory. When a write is made, a "update" flag is
set, and at the end of processing, if the update is set, then it writes
the file with changes out to a new file, and then renames it over the
original one.
The file descriptor is still passed to the write and lseek wrappers because
removing that would cause the change to be more intrusive. That can be
removed in a follow up cleanup patch that can wait till the next merge
window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWerqKAAoJEKKk/i67LK/80W0H/jbzBL4siTTenA0eZLmsxT8k
nbAM4fpdylpqUc6ku3QwjqqvbYxaLhiQsDtsVgXEoV7eelDgBedOSvCCrpZXn5co
y1VEunRfOIWMKLmoAdFUagWxdX25Pu9V6g74kdUwaiNnMtCy7+Ds7x8OwqASyd7t
e1WAhQ63ovslN88hHpkQVxCApYaocyPgU1lysBpN9dmvUS7Vkt/Bl4xhlVclnQKS
3QbPWXtS/alCOOYj/Fa71Lfi2GhDx41Z6KPq6hFgph//oPHOSIvceNnimfT+ejjw
1dKzM5EN386PhF3R27P+I0ovXnLNlCKmMZQUCUvlU/CjOOHHcIQNj8WHw9XB20k=
=5TS2
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace/recordmcount fix from Steven Rostedt:
"Russell King was reporting lots of warnings when he compiled his
kernel with ftrace enabled. With some investigation it was discovered
that it was his compile setup. He was using ccache with hard links,
which allowed recordmcount to process the same .o twice. When this
happens, recordmcount will detect that it was already done and give a
warning about it.
Russell fixed this by having recordmcount detect that the object file
has more than one hard link, and if it does, it unlinks the object
file after it maps it and processes then. This appears to fix the
issue.
As you did not like the fact that recordmcount modified the file in
place and thought that it should do the modifications in memory and
then write it out to disk and move it over the old file to prevent
other more subtle issues like the one above, a second patch is added
on top of Russell's to do just that. Luckily the original code had
write and lseek wrappers that I was able to modify to not do inplace
writes, but simply keep track of the changes made in memory. When a
write is made, a "update" flag is set, and at the end of processing,
if the update is set, then it writes the file with changes out to a
new file, and then renames it over the original one.
The file descriptor is still passed to the write and lseek wrappers
because removing that would cause the change to be more intrusive.
That can be removed in a follow up cleanup patch that can wait till
the next merge window"
* tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/scripts: Have recordmcount copy the object file
scripts: recordmcount: break hardlinks
Constifies tty_port_operations structure in
the tty code of the gdm724x driver since it
is not modified after its initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the sparse warnings about dereferencing a userspace pointer.
Once I updated the sparse annotations, I noticed a bug in
gdm_wimax_ioctl() where we pass a user space pointer to gdm_update_fsm()
which dereferences it. I fixed this.
Signed-off-by: Wim de With <nauxuron@wimdewith.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct sdu_stamp in the gdm_sdio.h is a timeval type.
'struct timeval now' is used for calculating elapsed time.
32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the gdm72xx driver to use ktime_t.
ktime_get() is better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub
are used to subtract two ktime variables.
Build tested this by saying Y to WIMAX_GDM72XX.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only a single fix this time and for a bug that's been in the kernel
since around about the start of 2013 (so no rush!)
* Out-of-bounds memory access in adis core (Analog Devices IMUs)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MxIN
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.4c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
3rd set of IIO fixes for the 4.4 cycle.
Only a single fix this time and for a bug that's been in the kernel
since around about the start of 2013 (so no rush!)
* Out-of-bounds memory access in adis core (Analog Devices IMUs)
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aiE2
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new stuff for IIO in the 4.5 cycle.
New driver features
- us5182
* Add interrupt support and rising / falling threshold events.
Cleanups / fixes to new stuff / minor additions
* Expose the IIO value formatting function for drivers to
make use of internally.
- ina2xx
* Fix wrong channel order
* Fix incorrect reporting of endianness
* Adding documentation of ABI unique to this device
- mma8452
* Drop an unused register description
* Use an enum for the channel index to aid readability
- sca3000
* Use standard NULL comparison style
- us5182
* fix an inconsistency in status of enable (a bug with no real effect until
above patches are applied)
* refactor the read_raw function to improve maintainability / readability.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWbX6IAAoJEFSFNJnE9BaI6E4QAIvGXHn4ew8ZH+IF3UP+n47C
WWtgeh7dEvhqpmXN3eWVo9bxA1JdwbE4/purWttszoJjzqowT0qAt6PuIUME+Md4
3jOQ41Sc99YjttIwkLpWTqq3H5c3Tn3q9guZ3Imiz9rmpgHRePQ8aatMGUpOp53m
AEY5JQHqCoWHLMEbEy/5w8RJdNf3cy3Re4kjtwrtp7CMynC4ob7dKE7kcZRvywEw
6m4hVOQusLvygg1j235czwBDnf79qYOo96z93Pk/auQlqKX3ce/7yQW3GXvWl97a
8FOmse3FNzX3jwWHELOdAZWIQSLBSqP9N4716qa4orVSihzqAZQ5CSEBPB0r2LS2
cgK4BL6+xjDkwXn9ui4FiyLdUeUjz/zRhvwFZdjwP63hGf5n9ggZO3RuVslc6/8z
DOHY5mLdg8CFlMlZUCnCc+1BjU8lgf90+a46Vx4ACJJiqIJrvNRxRKGQZyY/C9sO
O8h0Ep5mWovcK1+SWdQSsfxdcWcdb0nJFG/VQeJVxMeJR+5mD5lCYmIj5xFkOxJU
WP9xm+7rsCqSPW+vp8hlY3EWunIQB4gWROvLzWCTS2bKW7B12t1UapLZBrI1f6vK
JuqHrjKkK7RBRAEldKz6cWCToEaHE+I/k+uIRhlp0of2IPEvGpnm3NoPN1XH3RID
9boPy/eHuShq8EVg0WUt
=54PR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new drivers, functionality and cleanups for the 4.5 cycle.
The big one here is the configfs support which has been a long time in the
works but should allow for cleaner ways to do instantiation of those elements
of IIO that aren't directly connected to specific hardware. Lots of cool new
stuff we can use this for in the works!
New core stuff (basically all configfs support related)
* Configfs support
- Core support (was waiting for a configfs patch that went in around 4.4rc2)
- A little fixlet to add a configfs.h to contain a reference to the
configfs_subsystem structure.
* Some infrastructure to simplify handling of software based triggers
(i.e. ones with no actual hardware associated with them)
* A high resolution timer based trigger. This has been around for years
but until the configfs support was ready we didn't have a sensible way
of instantiating instances of it (the method used for the sysfs_trigger
has never been really satisfactory)
New Device Support
* AMS iAQ Volatile Organic Compounds sensor support.
* Freescale imx7d ADC driver
* Maxim MAX30100 oximeter driver (note that for these devices most of the
smart stuff will be in userspace - effectively they are just light sensors
with some interesting led synchronization as far as the kernel is concerned).
* Microchip mcp3421 support added to the mcp3422 driver.
* TI adc124s021 support added to the adc128s052 driver.
* TI ina219, inda226 power monitors. Note that there is an existing hwmon driver
for these parts, the usecase is somewhat different so it is unclear at this
point if the hwmon driver will eventually be replaced by a bridge from
this driver. In the meantime the Kconfig dependencies should prevent both
from being built.
New driver functionality
* us8152d power management support.
Cleanups, fixups
* Use list_for_each_entry_safe instead of list_for_each_safe with the entry
bit coded longhand.
* Select IRQ_WORK for IIO_DUMMY_EVGEN. This is a fix that somehow got lost
when the driver was moved so lets do it again.
* st-accel - drop an unused define.
* vz89x, lidar - optimize i2c transactions by using a single i2c tranfers
instead of multiple calls where supported (fall back to smbus calls as
before if not).
* Use dev_get_platdata() in staging drivers: tsl2x7x, adcs and frequency
drivers instead of direct access to the structure element.
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Bu7H
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.5
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWfLjWAAoJEEhZKYFQ1nG7R/cH/3xP4nz3pDDOpsX6U8Q1V81D
K7118WeAOx64sdGRZ3bsEjNko4NI1j2jcQU2Zgtx/I5Q0lJfNm4linNNWJHKEb/m
1VJVxFJXP6lwWImVWNJbyvhzel8mlgaNza+ZabUOAFmSig9q3yHUq5lDqzPVLZWY
z7lYQS+sOsCorsQierXiRxSRvkipB32NpdfhEXkj6P6Ji2a1UDDRA7F3f9k9t8QR
iI1T5+gbJL/3eo+ToOdlGciIUjoa4bK5b0Iz+QeU2eSOqjuVcu4tZO5IJbH/o10Z
dAhcDOr0DPEGzfpwihevyX3HcRKTKHPlzo2GdW5TJ5e7vm5C43fGHB0GgpIJBWw=
=7ZBY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
The chipidea changes for v4.5-rc1
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
Detailed description for patchset:
1. Add new MAX3355 extcon driver
- Maxim Integrated MAX3355E chip integrates a charge pump
and comparator to enable a system with an integrated
USB OTG dual-role transceiver to function as an USB OTG
dual-role device.
2. Update the extcon-arizona driver for jack detection
- Add the device binding for the jack detection and add
the documentation of extcon-arizona.c.
3. Fix the minor issue of extcon driver
- Add IRQF_ONESHOT to interrupt flags of extcon-rt8973.
- Fix the return value regmap_irq_get_virq() of
extcon-max(14577|77693|77843).c driver by using script[1].
[1] http://permalink.gmane.org/gmane.linux.kernel/2046107
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t21V
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.5
Detailed description for patchset:
1. Add new MAX3355 extcon driver
- Maxim Integrated MAX3355E chip integrates a charge pump
and comparator to enable a system with an integrated
USB OTG dual-role transceiver to function as an USB OTG
dual-role device.
2. Update the extcon-arizona driver for jack detection
- Add the device binding for the jack detection and add
the documentation of extcon-arizona.c.
3. Fix the minor issue of extcon driver
- Add IRQF_ONESHOT to interrupt flags of extcon-rt8973.
- Fix the return value regmap_irq_get_virq() of
extcon-max(14577|77693|77843).c driver by using script[1].
[1] http://permalink.gmane.org/gmane.linux.kernel/2046107
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
Declare that we support remote invalidation in case we are:
1. using fastreg method
2. always registering memory
Detect the invalidated rkey from the work completion info so we
won't invalidate it locally. The spec mandates that we must not rely
on the target remote invalidate our rkey so we must check it upon
a receive (scsi response) completion.
Signed-off-by: Jenny Derzhavetz <jennyf@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Unwinder rework (A revert followed by better fix)
- Build errors: MMUv2, modules with -Os
- highmem section mismatch build splat
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h2pT
-----END PGP SIGNATURE-----
Merge tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Sorry for this late pull request, but these are all important fixes
for code introduced/updated in this release which we will otherwise
end up back porting.
- Unwinder rework (A revert followed by better fix)
- Build errors: MMUv2, modules with -Os
- highmem section mismatch build splat"
* tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Catch Dwarf SNAFUs early
ARC: dw2 unwind: Don't bail for CIE.version != 1
Revert "ARC: dw2 unwind: Ignore CIE version !=1 gracefully instead of bailing"
ARC: Fix linking errors with CONFIG_MODULE + CONFIG_CC_OPTIMIZE_FOR_SIZE
ARC: mm: fix building for MMU v2
ARC: mm: HIGHMEM: Fix section mismatch splat
Since gpiochip .get() callback may return a negative error value, it
strictly limits the range of possible non-error returned values to
a subset of [30:0] bitmask, however on practice on success all
gpiochip drivers return either 0 for low signal or 1 for high signal,
this is assured by "gpio: *: Be sure to clamp return value" series of
changes. To avoid any confusion, misinterpretation and potential
errors while developing gpiochip drivers in future convert this
implicit assumption to a mandatory rule.
For output signals with unknown output signal state gpiochip drivers
should return a negative error instead of 0.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 45ad7db90b.
We have fixed all the drivers that were returning ambious values
not clamped to [0,1] or an error code, so return the error
propagating behaviour of the API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This code was also double-inverting a bool which makes no sense
so I removed that code and moved clamping toward the end.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also, this code was double-inverting a bool. That makes no
sense whatsoever, so I removed the double-invert.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also makes the driver start to return the error code, as the
end of the series make this work.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also starts to propagate the error code from the I2C
transaction as the end of the series adds support for that.
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start returning the error code if something fails, as the
end of the series augment the core to support this.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start to propagate the error code here as the end of the
series fixes this to work for all drivers.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by:Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
