omap_dmm_tiler.c can't be compiled as a module and it is built
unconditionally as part of omapdrm. Since it can't be used as a module,
there is no need for it to have an unused MODULE_ALIAS().
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
prism54 checks for dma mapping errors by comparison returned address
with zero, while pci_dma_mapping_error() should be used.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable the FW Logger to work over the SDIO interface in addition to over UART
interface. In the new design we use fw internal memory instead of packet ram
that was used in older (wl12xx) design. This change reduces the impact on TP
and stability.
A new event was added to notify fw logger is ready for reading. Dynamic
configuration to debugfs was added as well.
Signed-off-by: Shahar Patury <shaharp@ti.com>
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far we were using fs_initcall. It was (and still is) needed because
struct bus_type has to be registered early. However main bus
initialization has to happen later as it requires SPROM which depends on
NVRAM which depends on mtd.
Solve it by using fs_initcall only for bus_register call and module_init
for the rest. It affects bcma only when built-in obviously.
This was tested with BCM4706 and BCM5357C0 (BCM47XX), BCM4708A0
(ARCH_BCM_5301X) and BCM43225 (PCIe card with bcma as module).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: a67719d182 ("drm/rockchip: vop: spilt register related into rockchip_reg_vop.c")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Andrew Lunn says:
====================
Ethtool support for phy stats
This patchset add ethtool support for reading statistics from the PHY.
The Marvell and Micrel Phys are then extended to report receiver
packet errors and idle errors.
v2:
Fix linking when phylib is not enabled.
v3:
Inline helpers into ethtool.c, so fixing when phylib is a module.
v4:
Add missing static
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet PHYs can maintain statistics, for example errors while idle
and receive errors. Add an ethtool mechanism to retrieve these
statistics, using the same model as MAC statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.
This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.
But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Added a safeguard in the shutdown case. At least while not being
attached it is also possible to trigger a kernel bug by writing into
writeback_running. This change adds the same check before trying to
wake up the thread for that case.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Allows to use register, not register_quiet in udev to avoid "device_busy" error.
The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis
<g2p.code@gmail.com> does not unlock the mutex and hangs the kernel.
See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion.
Cc: Denis Bychkov <manover@gmail.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Gabriel de Perthuis <g2p.code@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
In bcache_init() function it forgot to unregister reboot notifier if
bcache fails to unregister a block device. This commit fixes this.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Subject : [PATCH v2] bcache: fix a livelock in btree lock
Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM)
This commit tries to fix a livelock in bcache. This livelock might
happen when we causes a huge number of cache misses simultaneously.
When we get a cache miss, bcache will execute the following path.
->cached_dev_make_request()
->cached_dev_read()
->cached_lookup()
->bch->btree_map_keys()
->btree_root() <------------------------
->bch_btree_map_keys_recurse() |
->cache_lookup_fn() |
->cached_dev_cache_miss() |
->bch_btree_insert_check_key() -|
[If btree->seq is not equal to seq + 1, we should return
EINTR and traverse btree again.]
In bch_btree_insert_check_key() function we first need to check upgrade
flag (op->lock == -1), and when this flag is true we need to release
read btree->lock and try to take write btree->lock. During taking and
releasing this write lock, btree->seq will be monotone increased in
order to prevent other threads modify this in cache miss (see btree.h:74).
But if there are some cache misses caused by some requested, we could
meet a livelock because btree->seq is always changed by others. Thus no
one can make progress.
This commit will try to take write btree->lock if it encounters a race
when we traverse btree. Although it sacrifice the scalability but we
can ensure that only one can modify the btree.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Joshua Schmid <jschmid@suse.com>
Cc: Zhu Yanhai <zhu.yanhai@gmail.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
The missing break means that we always return EAFNOSUPPORT when
faced with a request for an IPv6 loopback address.
Reported-by: coverity (CID 401987)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When an i2c-hid device is resumed from system sleep the driver resets
the device to be sure it is in known state. The device is expected to
issue an interrupt when reset is complete.
This reset might take few milliseconds to complete so if the HID driver
on top (hid-rmi) starts to set up the device by sending feature reports
etc. the device might not issue the reset complete interrupt anymore.
Below is what happens to touchpad on Lenovo Yoga 900 during resume from
system sleep:
[ 24.790951] i2c_hid i2c-SYNA2B29:00: i2c_hid_hwreset
[ 24.790973] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 24.790982] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 08
[ 24.793011] i2c_hid i2c-SYNA2B29:00: resetting...
[ 24.793016] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 01
Here i2c-hid sends reset command to the touchpad.
[ 24.794012] i2c_hid i2c-SYNA2B29:00: input: 06 00 01 00 00 00
[ 24.794051] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.794059] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=22 00 3f 03 0f 23 00 04 00 0f 01
Now hid-rmi puts the touchpad to correct mode by sending it a feature
report. This makes the touchpad not to issue reset complete interrupt.
[ 24.796092] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: waiting...
i2c-hid starts to wait for the reset interrupt to trigger which never
happens.
[ 24.798304] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.798313] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=25 00 17 00 09 01 42 00 2e 00 19 19 00 10 cc 06 74 04 0f
19 00 00 00 00 00
Yet another output report from hid-rmi driver.
[ 29.795630] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: finished.
[ 29.795637] i2c_hid i2c-SYNA2B29:00: failed to reset device.
After 5 seconds i2c-hid driver times out.
[ 29.795642] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 29.795649] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 01 08
[ 29.797576] dpm_run_callback(): i2c_hid_resume+0x0/0xb0 returns -61
[ 29.797584] PM: Device i2c-SYNA2B29:00 failed to resume: error -61
After this the touchpad does not work anymore (and also resume itself
gets slowed down because of the timeout).
Prevent sending of feature/output reports while the device is being
reset by adding a mutex which is held during that time.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Nish Aravamudan <nish.aravamudan@gmail.com>
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In sctp_close, sctp_make_abort_user may return NULL because of memory
allocation failure. If this happens, it will bypass any state change
and never free the assoc. The assoc has no chance to be freed and it
will be kept in memory with the state it had even after the socket is
closed by sctp_close().
So if sctp_make_abort_user fails to allocate memory, we should abort
the asoc via sctp_primitive_ABORT as well. Just like the annotation in
sctp_sf_cookie_wait_prm_abort and sctp_sf_do_9_1_prm_abort said,
"Even if we can't send the ABORT due to low memory delete the TCB.
This is a departure from our typical NOMEM handling".
But then the chunk is NULL (low memory) and the SCTP_CMD_REPLY cmd would
dereference the chunk pointer, and system crash. So we should add
SCTP_CMD_REPLY cmd only when the chunk is not NULL, just like other
places where it adds SCTP_CMD_REPLY cmd.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dummy_timer_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cs5535audio_dma_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The atiixp_dma_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit ceb5d58b21 ("net: fix sock_wake_async() rcu protection") from
the current 4.4 release cycle introduced a new flags member in
struct socket_wq and moved SOCKWQ_ASYNC_NOSPACE and SOCKWQ_ASYNC_WAITDATA
from struct socket's flags member into that new place.
Unfortunately, the new flags field is never initialized properly, at least
not for the struct socket_wq instance created in sock_alloc_inode().
One particular issue I encountered because of this is that my GNU Emacs
failed to draw anything on my desktop -- i.e. what I got is a transparent
window, including the title bar. Bisection lead to the commit mentioned
above and further investigation by means of strace told me that Emacs
is indeed speaking to my Xorg through an O_ASYNC AF_UNIX socket. This is
reproducible 100% of times and the fact that properly initializing the
struct socket_wq ->flags fixes the issue leads me to the conclusion that
somehow SOCKWQ_ASYNC_WAITDATA got set in the uninitialized ->flags,
preventing my Emacs from receiving any SIGIO's due to data becoming
available and it got stuck.
Make sock_alloc_inode() set the newly created struct socket_wq's ->flags
member to zero.
Fixes: ceb5d58b21 ("net: fix sock_wake_async() rcu protection")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-29
This series contains updates to ixgbe and ixgbevf.
William Dauchy provides a fix for ixgbevf that was implemented for ixgbe,
commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI budget when multiple
queues are enabled per vector"). The issue was that the polling routine
would increase the budget for receive to at least 1 per queue if multiple
queues were present, which resulted in receive packets being processed
when the budget was 0.
Emil provides minor cleanups for ixgbevf, one being that we need to
check rx_itr_setting with == and not &, since it is not a mask. Added
QSFP PHY support in ixgbe to allow for more accurate reporting of port
settings. Fixed the max RSS limit for X550 which is 63, not 64.
Veola fixes ixgbe ethtool reporting of backplane type interfaces as
1000/10000baseT link modes, instead, report the media as KR, KX or KX4
based on the backplane interface present.
Mark cleans up redundancy in the setting of hw_enc_features that makes
it appear that X550 has more encapsulation features than other devices.
Also do not set NETIF_F_SG any longer since that is set by the
register_netdev() call. Also fixed the X550EM_x revision check, which
needs to check a value, not just a bit.
Alex Duyck fixes additional bugs in ixgbe_clear_vf_vlans(), one being
that the mask was using a divide instead of a modulus, which resulted
in the mask bit being incorrectly set to 0 or 1 based on the value of
the VF being tested. Alex also found that he was not consistent in
using the "word" argument as an offset or as a register offset, so
made the code consistently use word as the offset in the array.
v2: dropped patch 8 of the original series, as it was undoing a part of
the fix Alex Duyck was doing in patch 9 of the original series.
Dropped based on feedback from Emil (the author).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
The following patch set contains some feature additions, code re-organization
and cleanup and a few non-critical fixes. Pls consider applying this to
the net-next tree. Thanks.
v3 changes: add a default case to the switch statement in patch 5 to
satisfy the compiler (-Wswitch).
v2 changes: replaced an if/else block that checks for error values with a
switch/case statement in patch 5.
Patch 1 fixes VF link state transition from disabled to auto that did
not work due to an issue in the FW. This issue could not be fixed in FW due
to some backward compatibility issues it causes with released drivers.
The issue has been fixed by introducing a new version (v2) of the cmd
from 10.6 FW onwards. This patch adds support for v2 version of this cmd.
Patch 2 reports a EOPNOTSUPP status to ethtool when the user tries to
configure BE3/SRIOV in VEPA mode as it is not supported by the chip.
Patch 3 cleansup FW flash image related constant definitions. Many of these
definitions (such as section offset values) were defined in decimal format
rather than hexa-decimal. This makes this part of the code un-readable.
Also some defines related to BE2 are labeld "g2" and defines related to BE3
are labeled "g3". This patch cleans up all of this to make this code more
readable.
Patch 4 moves the FW cmd code to be_cmds.c. All code relating to FW cmds
has been in be_cmds.[ch], excepting FW flash cmd related code.
This patch moves these routines from be_main.c to be_cmds.c.
Patch 5 adds a log message to report digital signature errors while
flashing a FW image. From FW version 11.0 onwards, the FW supports a new
"secure mode" feature (based on a jumper setting on the adapter.) In this
mode, the FW image when flashed is authenticated with a digital signature.
Patch 6 removes a line of code that has no effect.
Patch 7 removes some unused variables.
Patch 8 fixes port resource descriptor query via the GET_PROFILE FW cmd.
An earlier commit passed a specific pf_num while issuing this cmd as FW
returns descriptors for all functions when pf_num is zero. But, when pf_num
is set to a non-zero value, FW does not return the port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.
Patch 9 adds support for ethtool get-dump feature. In the past when this
option was not yet available, this feature was supported via the
--register-dump option as a workaround. This patch removes support for
FW-dump via --register-dump option as it is now available via --get-dump
option. Even though the "ethtool --register-dump" cmd which used to work
earlier, will now fail with ENOTSUPP error, we feel it is not an issue as
this is used only for diagnostics purpose.
Patch 10 bumps up the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's --get-dump option in be2net,
to retrieve FW dump. In the past when this option was not yet available,
this feature was supported via the --register-dump option as a workaround.
This patch removes support for FW-dump via --register-dump option as it is
now available via --get-dump option. Even though the
"ethtool --register-dump" cmd which used to work earlier, will now fail
with ENOTSUPP error, we feel it is not an issue as this is used only
for diagnostics purpose.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd") passed a specific pf_num while issuing a
GET_PROFILE_CONFIG cmd as FW returns descriptors for all functions when
pf_num is zero. But, when pf_num is set to a non-zero value, FW does not
return the Port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.
Fixes: 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd")
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eeh_error, fw_timeout, hw_error variables in the be_adapter structure are
not used anymore. An earlier patch that introduced adapter->err_flags to
store this information missed removing these variables.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a line of code that changes adapter->recommended_prio
value followed by yet another assignment.
Also, the variable is used to store the vlan priority value that is already
shifted to the PCP bits position in the vlan tag format. Hence, the name of
this variable is changed to recommended_prio_bits.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(based on a jumper setting on the adapter.) In this mode, the FW image when
flashed is authenticated with a digital signature. This patch logs
appropriate error messages and return a status to ethtool when errors
relating to FW image authentication occur.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3". This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BE3 chip doesn't support VEPA mode.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.
The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two rules to handle aborting volatile or atomic writes.
1. drop atomic writes
- we don't need to keep any stale db data.
2. write journal data
- we should keep the journal data with fsync for db recovery.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If filesystem is readonly, leave user message info instead of recovering
inline dot inode.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Pull block fixes from Jens Axboe:
"Make the block layer great again.
Basically three amazing fixes in this pull request, split into 4
patches. Believe me, they should go into 4.4. Two of them fix a
regression, the third and last fixes an easy-to-trigger bug.
- Fix a bad irq enable through null_blk, for queue_mode=1 and using
timer completions. Add a block helper to restart a queue
asynchronously, and use that from null_blk. From me.
- Fix a performance issue in NVMe. Some devices (Intel Pxxxx) expose
a stripe boundary, and performance suffers if we cross it. We took
that into account for merging, but not for the newer splitting
code. Fix from Keith.
- Fix a kernel oops in lightnvm with multiple channels. From Matias"
* 'for-linus' of git://git.kernel.dk/linux-block:
lightnvm: wrong offset in bad blk lun calculation
null_blk: use async queue restart helper
block: add blk_start_queue_async()
block: Split bios on chunk boundaries
The MMCFG PCI accessors weren't being setup for NumacConnect2
correctly due to over-early assignment; this would create the
potential for the wrong PCI domain to be accessed.
Fix this by using the correct arch-specific PCI init function.
Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Acked-by: Steffen Persvold <sp@numascale.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1451498807-15920-1-git-send-email-daniel@numascale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Otherwise, we can get mismatched largest extent information.
One example is:
1. mount f2fs w/ extent_cache
2. make a small extent
3. umount
4. mount f2fs w/o extent_cache
5. update the largest extent
6. umount
7. mount f2fs w/ extent_cache
8. get the old extent made by #2
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Use f2fs_sync_fs to clean up codes in f2fs_ioc_write_checkpoint.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: remove unused err variable]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds a max block check for get_data_block_bmap.
Trinity test program will send a block number as parameter into
ioctl_fibmap, which will be used in get_node_path(), when the block
number large than f2fs max blocks, it will trigger kernel bug.
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Xue Liu <liuxueliu.liu@huawei.com>
[Jaegeuk Kim: fix missing condition, pointed by Chao Yu]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
fix bugs:
1. len could be updated incorrectly when start+len is beyond isize.
2. If there is a hole consisting of more than two blocks, it could
fail to add FIEMAP_EXTENT_LAST flag for the last extent.
3. If there is an extent beyond isize, when we search extents in a range
that ends at isize, it will also return the extent beyond isize,
which is outside the range.
Signed-off-by: Fan li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Sometimes we keep dumb when IO error occur in lower layer device, so user
will not receive any error return value for some operation, but actually,
the operation did not succeed.
This sould be avoided, so this patch reports such kind of error to user.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
__recover_do_dentries will try to grab free space in storage, so fix to
add missing f2fs_balance_fs here.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
