Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.
Fix this by aborting the authentication attempt when suspending.
Cc: stable@vger.kernel.org
Fixes: 12e7f51702 ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When still authenticating the mac80211 code handling a deauthentication
requests from userspace doesn't verify that the request is valid in any
way, fix that. Additionally, it never returns an error, even if there's
no connection or authentication attempt, fix that as well.
While at it, move the message to not print a message in the error case
and to distinguish between the two cases.
Also simplify the code by duplicating the cfg80211 call.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The bss struct might be freed in ieee80211_rx_bss_put(),
so we shouldn't use it afterwards.
Cc: stable@vger.kernel.org (3.10+)
Fixes: 817cee7675 ("mac80211: track AP's beacon rate and give it to the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In certain situations we want to trigger reprocessing
of the last regulatory hint. One situation in which
this makes sense is the case where the cfg80211 was
built-in to the kernel, CFG80211_INTERNAL_REGDB was not
enabled and the CRDA binary is on a partition not availble
during early boot. In such a case we want to be able to
re-process the same request at some other point.
When we are asked to re-process the same request we need
to be careful to not kfree it, addresses that.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[rename function]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add missing update on the rx status vht flag of the last
data packet. Otherwise, cfg80211_calculate_bitrate_vht
may not consider the channel width resulting in wrong
calculation of the received bitrate.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function was quite big. This splits out beacon
updating into a separate function for improved
maintenance and extension.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "nl80211: send event when AP operation is stopped" added an
event to notify user space that an AP interface has been stopped, to
handle cases such as suspend etc. The event is sent regardless
if the stop AP flow was triggered by user space or due to internal state
change.
This might cause issues with wpa_supplicant/hostapd flows that consider
stop AP flow as a synchronous one, e.g., AP/GO channel change in the
absence of CSA support. In such cases, the flow will restart the AP
immediately after the stop AP flow is done, and only handle the stop
AP event after the current flow is done, and as a result stop the AP
again.
Change the current implementation to only send the event in case the
stop AP was triggered due to an internal reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send Channel Availability Check time as a parameter
of start_radar_detection() callback.
Get CAC time from regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce DFS CAC time as a regd param, configured per REG_RULE and
set per channel in cfg80211. DFS CAC time is close connected with
regulatory database configuration. Instead of using hardcoded values,
get DFS CAC time form regulatory database. Pass DFS CAC time to user
mode (mainly for iw reg get, iw list, iw info). Allow setting DFS CAC
time via CRDA. Add support for internal regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to set world regulatory domain in case of user
request (iw reg set 00).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the struct device_type with the uevent function
etc., just fill the country alpha2 when sending the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Error codes returned by cfg80211_chandef_dfs_required() are ignored
when trying to join an IBSS. Fix this by printing an error and
returning.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct. We should just make sure
they *are* when we call this function.
Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mesh support for DFS channels was added, we also need to check
for DFS channels when performing a channel switch with
NL80211_IFTYPE_MESHPOINT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[use switch statement, slight code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously we were warning and using automatic when a driver sent an
update request with SMPS off. This patch makes it possible for
drivers to disable SMPS at runtime, for whatever reason.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce NL80211_RRF_AUTO_BW rule flag. If this flag set
maximum available bandwidth should be calculated base on
contiguous rules and wider channels will be allowed to cross
multiple contiguous/overlapping frequency ranges.
In case of old kernels maximum bandwidth from regulatory
rule will be used, while there is no NL80211_RRF_AUTO_BW flag.
This fixes the previous commit 9752482083
("cfg80211: regulatory introduce maximum bandwidth calculation")
which was found to be a problem for userspace API compatibility.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[edit commit log, use sizeof()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NAPI was originally added to mac80211 a long time ago (by John in
commit 4e6cbfd09c in July 2010), but then removed years later
(by Stanislaw in commit 30c97120c6 in February 2013). No driver
ever used it, so that was fine.
Now I'm adding support for NAPI to our driver, so add some code
to mac80211 again to support NAPI. John was originally wrapping
some (but not nearly all NAPI-related functions), but that doesn't
scale very well with the number of functions that are there, some
of which are even only inlines. Thus, instead of doing that, let
the drivers manage the NAPI struct, except for napi_add() which is
needed so mac80211 knows how to call napi_gro_receive().
Also remove some no longer needed definitions that were left when
NAPI support was removed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've already checked the IE length and assigned request->ie
based on that, so continue using it to make the code a bit
clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no driver using this flag and consequently no userspace
application is actually looking at it. As it seems unlikely for
any driver to start using it, remove it and the (very little)
code that used it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Create a function to return a descriptive string for each reason code,
and print that in addition to the numeric value in the kernel log. These
codes are easily found on popular search engines, but one is generally
not able to access the internet when dealing with wireless connectivity
issues.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
[use 'unknown' rather than 'invalid' since more valid codes exist]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to start iterating the list only to break on the
first item, just use !list_empty() and also simplify the whole
conditional into a single expression.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove size of SSID IE from the IE buffer in scan and
sched scan, since this IE isn't added to this buffer.
Reviewed-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add beacon_loss debugfs file that emulates
ieee80211_beacon_loss call from the driver.
This can be used for various testing scenarios.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of beacon_loss with IEEE80211_HW_CONNECTION_MONITOR
device, mac80211 probes the ap (and disconnects on timeout)
but ignores the ack.
If we already got an ack, there's no reason to continue
disconnecting. this can help devices that supports
IEEE80211_HW_CONNECTION_MONITOR only partially (e.g. take
care of keep alives, but does not probe the ap.
In case the device wants to disconnect without probing,
it can just call ieee80211_connection_loss.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit f38a5181d9 ("ceph: Convert to immutable biovecs") introduced
a NULL pointer dereference, which broke rbd in -rc1. Fix it.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Handling redirect replies requires both map_sem and request_mutex.
Taking map_sem unconditionally near the top of handle_reply() avoids
possible race conditions that arise from releasing request_mutex to be
able to acquire map_sem in redirect reply case. (Lock ordering is:
map_sem, request_mutex, crush_mutex.)
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Factor out logic from ceph_osdc_start_request() into a new helper,
__ceph_osdc_start_request(). ceph_osdc_start_request() now amounts to
taking locks and calling __ceph_osdc_start_request().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
We already have a band variable, so the new one is just
shadowing it, but the existing one already holds the
same value so just remove the inner one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During channel context assignment, the interface should
be found by interface iteration, so we need to assign the
pointer before the channel context.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "new" fragmentation code (since my rewrite almost 5 years ago)
erroneously sets skb->len rather than using skb_trim() to adjust
the length of the first fragment after copying out all the others.
This leaves the skb tail pointer pointing to after where the data
originally ended, and thus causes the encryption MIC to be written
at that point, rather than where it belongs: immediately after the
data.
The impact of this is that if software encryption is done, then
a) encryption doesn't work for the first fragment, the connection
becomes unusable as the first fragment will never be properly
verified at the receiver, the MIC is practically guaranteed to
be wrong
b) we leak up to 8 bytes of plaintext (!) of the packet out into
the air
This is only mitigated by the fact that many devices are capable
of doing encryption in hardware, in which case this can't happen
as the tail pointer is irrelevant in that case. Additionally,
fragmentation is not used very frequently and would normally have
to be configured manually.
Fix this by using skb_trim() properly.
Cc: stable@vger.kernel.org
Fixes: 2de8e0d999 ("mac80211: rewrite fragmentation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a station leaves an IBSS network, the
corresponding BSS is not dropped from cfg80211 if there are
other active stations in the network. But, the small
window that is present when trying to determine a station's
status based on IEEE80211_IBSS_MERGE_INTERVAL introduces
a race.
Instead of trying to keep the BSS, always remove it when
leaving an IBSS network. There is not much benefit to retain
the BSS entry since it will be added with a subsequent join
operation.
This fixes an issue where a dangling BSS entry causes ath9k
to wait for a beacon indefinitely.
Cc: <stable@vger.kernel.org>
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver cannot start the AP or when the assignement
of the beacon goes wrong, we need to unassign the vif.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the previous commit, when a scan finishes, it is in theory
possible to hit the following sequence:
1. interface starts being removed
2. scan is cancelled by driver and cfg80211 is notified
3. scan done work is scheduled
4. interface is removed completely, rdev->scan_req is freed,
event sent to userspace but scan done work remains pending
5. new scan is requested on another virtual interface
6. scan done work runs, freeing the still-running scan
To fix this situation, hang on to the scan done message and block
new scans while that is the case, and only send the message from
the work function, regardless of whether the scan_req is already
freed from interface removal. This makes step 5 above impossible
and changes step 6 to be
5. scan done work runs, sending the scan done message
As this can't work for wext, so we send the message immediately,
but this shouldn't be an issue since we still return -EBUSY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface/wdev is removed, any ongoing scan should be
cancelled by the driver. This will make it call cfg80211, which
only queues a work struct. If interface/wdev removal is quick
enough, this can leave the scan request pending and processed
only after the interface is gone, causing a use-after-free.
Fix this by making sure the scan request is not pending after
the interface is destroyed. We can't flush or cancel the work
item due to locking concerns, but when it'll run it shouldn't
find anything to do. This leaves a potential issue, if a new
scan gets requested before the work runs, it prematurely stops
the running scan, potentially causing another crash. I'll fix
that in the next patch.
This was particularly observed with P2P_DEVICE wdevs, likely
because freeing them is quicker than freeing netdevs.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fixes: 4a58e7c384 ("cfg80211: don't "leak" uncompleted scans")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately I forgot this during the merge window, but the
patch seems small enough to go in as a fix. The userspace API
bug that was the reason for disabling it has long been fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the netlink skb is exhausted split_start is left set. In the
subsequent retry, with a larger buffer, the dump is continued from the
failing point instead of from the beginning.
This was causing my rt28xx based USB dongle to now show up when
running "iw list" with an old iw version without split dump support.
Cc: stable@vger.kernel.org
Fixes: 3713b4e364 ("nl80211: allow splitting wiphy information in dumps")
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[avoid the entire workaround when state->split is set]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_start_roc_work() might add a new roc
to existing roc, and tell cfg80211 it has already
started.
However, this might happen before the roc cookie
was set, resulting in REMAIN_ON_CHANNEL (started)
event with null cookie. Consequently, it can make
wpa_supplicant go out of sync.
Fix it by setting the roc cookie earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This capabilities weren't propagated to the radiotap header.
We don't set here the VHT_KNOWN / MCS_HAVE flag because not
all the low level drivers will know how to properly flag
the frames, hence the low level driver will be in charge
of setting IEEE80211_RADIOTAP_MCS_HAVE_FEC,
IEEE80211_RADIOTAP_MCS_HAVE_STBC and / or
IEEE80211_RADIOTAP_VHT_KNOWN_STBC according to its
capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In association request frames, there may be IEs passed from
userspace (such as interworking IEs) between HT and VHT, so
add code to insert those inbetween them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In probe request frames, the VHT IEs should come before any
vendor IEs, but after interworking and similar, so add code
to order them correctly wrt. the IEs passed from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the operating mode field is needed when an association
request contains the operating mode notification element and
it's not just changed later on the fly.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[clarify commit log, comments & fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we will get regulatory request with rule
where max_bandwidth_khz is set to 0 handle this
case as a special one.
If max_bandwidth_khz == 0 we should calculate maximum
available bandwidth base on all frequency contiguous rules.
In case we need auto calculation we just have to set:
country PL: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ AUTO), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
This mean we will calculate maximum bw for rules where
AUTO (N/A) were set, 160MHz (5330 - 5170) in example above.
So we will get:
(5170 - 5250 @ 160), (N/A, 20)
(5250 - 5330 @ 160), (N/A, 20), DFS
In other case:
country FR: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
We will get 80MHz (5250 - 5170):
(5170 - 5250 @ 80), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
Base on this calculations we will set correct channel
bandwidth flags (eg. IEEE80211_CHAN_NO_80MHZ).
We don't need any changes in CRDA or internal regulatory.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[extend nl80211 description a bit, fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
