This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We should never be busy performing transfers at suspend late, thus
there are no reason to check for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At system suspend_late, runtime PM has been disabled by the PM core
which means we can safely operate on these resources. Consequentially
we no longer have to wait until the noirq phase of the system suspend.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since the runtime PM state is expected to be active according to the
amba bus, we must align our behaviour while probing to it.
Moreover, this is needed to be able to have the driver fully functional
without depending on CONFIG_RUNTIME_PM.
Since the device is active while a successful probe has been completed,
the reference counting for the clock will be screwed up and never reach
zero. We resolve this by implementing runtime PM callbacks and let them
handle the resources accordingly, including the clock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[wsa: s/#if/#ifdef/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The amba bus are responsible for pm_runtime_enable|disable, remove the
redundant pm_runtime_disable at driver removal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* functions to simplify code and error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the former platform data struct nmk_i2c_controller into the
per-device state container struct i2c_nmk_client, and remove all
the platform data probe path hacks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: use 100kHz as default]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new drivers: Kontron PLD, Wondermedia VT
- mv64xxx driver gained sun4i support and a bigger cleanup
- duplicate driver 'intel-mid' removed
- added generic device tree binding for sda holding time (and
designware driver already uses it)
- we tried to allow driver probing with only device tree and no i2c
ids, but I had to revert it because of side effects. Needs some
rethinking.
- driver bugfixes, cleanups...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c-designware: use div_u64 to fix link
i2c: Kontron PLD i2c bus driver
i2c: iop3xxx: fix build failure after waitqueue changes
i2c-designware: make SDA hold time configurable
i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
i2c: imx: allow autoloading on dt ids
i2c: mv64xxx: Fix transfer error code
i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
i2c: omap: correct usage of the interrupt enable register
i2c-pxa: prepare clock before use
Revert "i2c: core: make it possible to match a pure device tree driver"
i2c: nomadik: allocate adapter number dynamically
i2c: nomadik: support elder Nomadiks
i2c: mv64xxx: Add Allwinner sun4i compatible
i2c: mv64xxx: make the registers offset configurable
i2c: mv64xxx: Add macros to access parts of registers
i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
i2c: designware: fix race between subsequent xfers
i2c: bfin-twi: Read and write the FIFO in loop
i2c: core: make it possible to match a pure device tree driver
...
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nomadik I2C was using a local atomic counter to number
the I2C adapters. This does not work on configurations where
you also add, say a GPIO bit-banged adapter to the system.
They will start to conflict about being adapter 0.
There is no reason to use the numbered adapter function, and
the semantic effect on systems with only Nomadik I2C blocks
will be none - instead of increasing the number atomically
in the driver itself, it is done in the I2C core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C block was introduced with the Nomadik STn8815
SoC (the STn8810 incidentally is identical to the one named
i2c-stu300.c). However as developments have only been tested
on the DB8500 family, it was not properly working with the
STn8815 anymore.
Rectify this by adding some vendor variant data in the same
manner as other PrimeCells, and switch code path depending
on version.
Tested on the S8815 Nomadik dongle.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases. This is just extra
cruft code that can be removed.
A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
twice.
* I verified that there were no cases where xxx_get_drvdata() was
being called in these drivers and checking for / relying on the NULL
return value.
This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
cppcheck rightfully reports those as "reassigned a value before the old
one has been used."
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Amend the I2C nomadik pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
i2c xfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle, and for runtime cases inbetween
I2C transfers.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: fixed braces on one else-branch]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.
[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
Now that u5500 is obsolete, u8500 is the only user of the Nomadik
i2c driver. As such there is no requirement to differentiate between
initialisation values. By the time a new SoC is released, almost all
of the ux500 platform will be DT:ed, so we can make decisions based
on the compatible property instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The i2c-nomadik gateware is really a PrimeCell APB device. By hosting
the driver under the amba bus we can access it more easily, for
example using the generic pci-amba driver. The patch also fixes the
mach-ux500 users, so they register an amba device instead than a
platform device.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The header and driver are only used by arm/mach-u8500 (and potentially
arm/mach-nomadik), but the STA2X11 I/O Hub exports on PCIe a number of
devices, including i2c-nomadik. This patch allows compilation of the
driver under x86.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This fixes a number of whitespace and punctuation problems
around the Nomadik I2C driver.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There was a missing struct item in the kerneldoc, add it and fix
another pretty-printing formatting issue with a missing space.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If there is a signal pending and wait_for_completion_interruptible_timeout
exited because of the -ERESTARTSYS error we are unable to send any more
i2c messages.
So, deprecate this _interruptible_ variant call.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.
2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus/i2c-2638' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: move setup to the earlier subsys initcall
i2c-bfin-twi: handle faulty slave devices better
i2c-mv64xxx: send repeated START between messages in xfer
i2c-nomadik: fix regression on adapter name
i2c-omap: Set latency requirements only once for several messages
i2c-eg20t: add driver for Intel EG20T
i2c-ocores: add some device tree documentation
i2c-ocores: Use devres for resource allocation
i2c-ocores: Adapt for device tree
i2c-iop3xx: add iomem annotation
