Using bit operations makes it easier to improve the driver.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert to watchdog subsystem. As part of that rework, use devm functions
where possible, and replace almost all static variables with a dynamically
allocated data structure.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use more common function and variable names.
Use pdev instead of dev for platform device.
Use sp5100_tco_probe() instead of sp5100_tco_init() for the probe function.
Drop sp5100_tco_cleanup(); just move the code into sp5100_tco_remove().
Use sp5100_tco_init() instead of sp5100_tco_init_module() for the module
initialization function.
Use sp5100_tco_exit() instead of sp5100_tco_cleanup_module() for the module
exit function.
Use consistent defines for accessing the watchdog control register.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use dev_ instead of pr_ functions where possible.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Match PCI device in module init function, not in the probe function.
It is pointless trying to probe if we can determine early that the device
is not supported.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There are too many unnecessary goto statements in sp5100_tco_setupdevice().
Rearrange the code and limit goto statements to error handling.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
By using standard error codes, we can identify and return more than one
error condition.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use request_muxed_region for multiplexed IO memory regions.
Also, SP5100_IO_PM_INDEX_REG/SP5100_IO_PM_DATA_REG are only
used during initialization; it is unnecessary to keep the
address range reserved.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to all published information, the watchdog disable bit for SB800
compatible controllers is bit 1 of PM register 0x48, not bit 2. For the
most part that doesn't matter in practice, since the bit has to be cleared
to enable watchdog address decoding, which is the default setting, but it
still needs to be fixed.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
SP5100_IO_PM_INDEX_REG and SB800_IO_PM_INDEX_REG are used inconsistently
and define the same value. Just use SP5100_IO_PM_INDEX_REG throughout.
Do the same for SP5100_IO_PM_DATA_REG and SB800_IO_PM_DATA_REG.
Use helper functions to access the indexed registers.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job") has the
effect of deferring timer handling in case of high CPU load, hence
delaying the delayed work allthought the worker is running which
high realtime priority.
As hrtimers are not managed by softirqs, this patch replaces the
delayed work by a plain work and uses an hrtimer to schedule that work.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This does the necessary cleanup on driver unload automatically.
Signed-off-by: André Draszik <git@andred.net>
Cc: linux-watchdog@vger.kernel.org
Cc: John Crispin <john@phrozen.org>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the watchdog hardware is enabled/running during boot, e.g.
due to a boot loader configuring it, we must tell the
watchdog framework about this fact so that it can ping the
watchdog until userspace opens the device and takes over
control.
Do so using the WDOG_HW_RUNNING flag that exists for exactly
that use-case.
Given the watchdog driver core doesn't know what timeout was
originally set by whoever started the watchdog (boot loader),
we make sure to update the timeout in the hardware according
to what the watchdog core thinks it is.
Signed-off-by: André Draszik <git@andred.net>
Cc: linux-watchdog@vger.kernel.org
Cc: John Crispin <john@phrozen.org>
Reviewed-by: Guenter Roeck <Linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When the watchdog device is suspended, its timeout is set to the maximum
value. During resume, the previously set timeout should be restored.
This does not work at the moment.
The suspend function calls
imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
and resume reverts this by calling
imx2_wdt_set_timeout(wdog, wdog->timeout);
However, imx2_wdt_set_timeout() updates wdog->timeout. Therefore,
wdog->timeout is set to IMX2_WDT_MAX_TIME when we enter the resume
function.
Fix this by adding a new function __imx2_wdt_set_timeout() which
only updates the hardware settings. imx2_wdt_set_timeout() now calls
__imx2_wdt_set_timeout() and then saves the new timeout to
wdog->timeout.
During suspend, we call __imx2_wdt_set_timeout() directly so that
wdog->timeout won't be updated and we can restore the previous value
during resume. This approach makes wdog->timeout different from the
actual setting in the hardware which is usually not a good thing.
However, the two differ only while we're suspended and no kernel code is
running, so it should be ok in this case.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Cc: stable@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When running a command like 'chrt -f 50 dd if=/dev/zero of=/dev/null',
the watchdog_worker fails to service the HW watchdog and the
HW watchdog fires long before the watchdog soft timeout.
At the moment, the watchdog_worker is invoked as a delayed work.
Delayed works are handled by non realtime kernel threads. The
WQ_HIGHPRI flag only increases the niceness of that threads.
This patch replaces the delayed work logic by kthread delayed work,
and sets the associated kernel task to SCHED_FIFO with the highest
priority, in order to ensure that the watchdog worker will run as
soon as possible.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a restart function to the davinci watchdog timer driver.
This is copied from arch/arm/mach-davinci/time.c and will allow us to
remove the code from there.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All parameters of watchdog_init_timeout() are documented with exception
of wdd, thus generating a build warning.
This patch document it and so remove the following build warning:
drivers/watchdog/watchdog_core.c:113: warning: No description found for parameter 'wdd'
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The new hpwdt_my_nmi() function is used conditionally, which produces
a harmless warning in some configurations:
drivers/watchdog/hpwdt.c:478:12: error: 'hpwdt_my_nmi' defined but not used [-Werror=unused-function]
This moves it inside of the #ifdef that protects its caller, to silence
the warning.
Fixes: 621174a92851 ("watchdog: hpwdt: Check source of NMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when it is defined just a few lines
above from where it is used.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The initial info message (early in the xen_wdt_init_module() function)
is not very useful and we already have a message on successful probe. If
the probe fails, additional messages are printed anyway.
The version number serves no useful purpose and it ran out of favor
upstream anyway.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the xen_wdt driver to use the watchdog subsystem instead of
registering and manipulating the char device directly through the misc
API. This is mainly getting rid of the "write" and "ioctl" methods and
part of the watchdog control logic (which are all implemented by the
watchdog subsystem).
Even though the watchdog subsystem supports registering and handling
multiple watchdog devices at the same time, the xen_wdt driver has an
inherent limitation of only one device due to the way the Xen hypervisor
exposes watchdog functionality. However, the driver can now coexist with
other watchdog devices (supported by different drivers).
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for Spreadtrum SC9860 platform.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog core includes a worker function which pings the
watchdog until user app starts pinging it and which also
pings it if the HW require more frequent pings.
Use that function instead of the dedicated timer.
In the mean time, we can allow the user to change the timeout.
Then change the timeout module parameter to use seconds and
use the watchdog_init_timeout() core function.
On some HW (eg: the 8xx), SWCRR contains bits unrelated to the
watchdog which have to be preserved upon write.
This driver has nothing preventing the use of the magic close, so
enable it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The first patch above (https://patchwork.kernel.org/patch/9970181/)
makes the oops go away, but it just papers over the problem. The real
problem is that the watchdog core clears WDOG_HW_RUNNING in
watchdog_stop, and the gpio driver fails to set it in its stop
function when it doesn't actually stop it. This means that the core
doesn't know that it now has responsibility for petting the device, in
turn causing the device to reset the system (I hadn't noticed this
because the board I'm working on has that reset logic disabled).
How about this (other drivers may of course have the same problem, I
haven't checked). One might say that ->stop should return an error
when the device can't be stopped, but OTOH this brings parity between
a device without a ->stop method and a GPIO wd that has always-running
set. IOW, I think ->stop should only return an error when an actual
attempt to stop the hardware failed.
From: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The watchdog framework clears WDOG_HW_RUNNING before calling
->stop. If the driver is unable to stop the device, it is supposed to
set that bit again so that the watchdog core takes care of sending
heart-beats while the device is not open from user-space. Update the
gpio_wdt driver to honour that contract (and get rid of the redundant
clearing of WDOG_HW_RUNNING).
Fixes: 3c10bbde10 ("watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The initial info message (early in the esb_probe() function) is not very
useful and we already have a message on successful probe, which includes
device identification. If the probe fails (e.g. PCI related errors),
additional messages are printed anyway.
The version number was only used in the initial info message. Other than
that, it serves no useful purpose and it ran out of favor upstream
anyway.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The minimum, maximum and default values for the watchdog heartbeat
(timeout) were hardcoded in several places (including module parameter
description and warning message for invalid module parameter value).
This patch adds macros for the aforementioned values and replaces all
occurences of hardcoded values by these macros.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Support multiple i6300esb devices simultaneously, by removing the single
device restriction in the original design and leveraging the multiple
device support of the watchdog subsystem.
This patch replaces the global definitions of watchdog device data with
a dynamically allocated structure. This structure is allocated during
device probe, so multiple independent structures can be allocated if
multiple devices are probed.
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the i6300esb driver to use the watchdog subsystem instead of the
legacy watchdog API. This is mainly just getting rid of the "write" and
"ioctl" methods and part of the watchdog control logic (which are all
implemented by the watchdog subsystem).
Even though the watchdog subsystem supports registering and handling
multiple watchdog devices at the same time, the i6300esb driver still
has a limitation of only one i6300esb device due to some global variable
usage that comes from the original design. However, the driver can now
coexist with other watchdog devices (supported by different drivers).
Signed-off-by: Radu Rendec <rrendec@arista.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Do not claim the NMI (i.e. return NMI_DONE) if the source of
the NMI isn't the iLO watchdog or debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Xen watchdog driver uses __kernel_time_t and ktime_to_timespec()
internally for managing its timeouts. Both are deprecated because of
y2038 problems. The driver itself is fine, since it only uses monotonic
times, but converting it to use ktime_get_seconds() avoids the deprecated
interfaces and is slightly simpler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch removes the windows protection routine that got
now covered by the wdt core.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The DA9062 watchdog occasionally enters error condition and resets the
system if the timeout is changed quickly after the timer was enabled.
The method of disabling and waiting for > 150 µs before setting the
new timeout is taken from the DA9052 driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9062 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Moxart does not appear to be using the interrupt from the
watchdog timer, maybe it's not even routed, so as to support
more architectures with this driver, make the interrupt
optional.
While we are at it: actually enable the use of the interrupt
if present by setting the right bit in the control register
and define the missing control register bits.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This renames all the driver files and symbols for the Gemini
watchdog to FTWDT010 as it has been revealed that this IP block
is a generic watchdog timer from Faraday Technology used in
several SoC designs.
Select this driver by default for the Gemini, it is a sensible
driver to always have enabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This converts the GPIO watchdog driver to use GPIO descriptors
instead of relying on the old method to read out GPIO numbers
from the device tree and then using those with the old GPIO
API.
The descriptor API keeps track of whether the line is active
low so we can remove all active low handling and rely on the
GPIO descriptor to deal with this for us.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This add "dev" and "np" variables to make the probe() function
a bit easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
