Lenovo Thinkpad 10 has wacom digitizer connected as a I2C-HID device. Add
generic support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
input_mt_sync_frame() calls input_mt_report_pointer_emulation() and do
some internal steps required to keep in sync the state of the touch within
the various reports.
Given that we use input_mt_get_slot_by_key() in this driver, it is better to
use input_mt_sync_frame().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
27QHD has the same x_min/y_min (WACOM_CINTIQ_OFFSET) as other Cintiqs.
ABS_MISC event is required for PAD packet to work properly with
xf86-input-wacom.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After PAD moved to its own interface, there were duplicated statements in
wacom_setup_pentouch_input_capabilities. Merge them together to reduce future
maintenance effort.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
stylus_in_proximity is used to make sure no touch event is sent while pen is in
proximity. touch_down is used to make sure a touch up event is sent when pen
comes into proximity while touch is down.
Two touch routines didn't store touch_down. One touch routine forgot to check
stylus_in_proximity before sending touch events. This patch fixes those issues.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It appears that the Cintiq Companion Hybrid does not send an ABS_MISC event to
userspace when any of its ExpressKeys are pressed. This is not strictly
necessary now that the pad exists on its own device, but should be fixed for
consistency's sake.
Traditionally both the stylus and pad shared the same device node, and
xf86-input-wacom would use ABS_MISC for disambiguation. Not sending this causes
the Hybrid to behave incorrectly with xf86-input-wacom beginning with its
8f44f3 commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.
While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Users may use unsupported tools on Cintiq or Intuos. When invalid tools or data
are detected, they should be ignored. That is, no event from those tools should
be reported.
Consolidating that code in wacom_intuos_inout simplifies the logic and make it
easier for future code change.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.
wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).
That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a HID descriptor places HID_DG_CONTACTID before HID_DG_X and HID_DG_Y then
the ABS_X and ABS_Y will not be automatically initialized by the call to
input_mt_init_slots. To ensure that this is not a problem, we relocate that
call to occur after HID parsing has been completed and we've initalized all the
multitouch axes.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defined outbound offset for DTU and Cintiq. But didn't update
the relevant maximum values. Oops...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are screen to tablet offsets for newer Cintiq and DTU models.
These offsets serve as outbound tracking for those display tablets.
Use defines instead of hardcoded numbers for the offsets.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is not necessarily sufficient to look only at the physical and logical
usages when determining if a field is for the pen or touch. Some fields
are not contained in a sub-collection and thus only have an application
usage. Not checking the application usage in such cases causes us to
ignore the field entirely, which may lead to incorrect behavior.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide the resolution of several angular axes (tilt, pen rotation, puck
rotation) to userspace. Because these values are natively degree-based, we
need to convert them to into units/radian as required by the input_absinfo
struct. To ensure wraparound behaves properly for the rotation axes, the
converted value was rounded up rather than rounded nearest.
Notably, the touchring axes (ABS_WHEEL and ABS_THROTTLE) are left without a
a declared resolution because the their low resolution cannot be accurately
represented (the worst-case rounding-induced error would be ~16 degrees).
Pre-scaling the values and range by at least 10x would reduce the error in
the resolution to acceptable levels, but the xf86-input-wacom driver is not
able to use pre-scaled values for these axes at this time.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Centers the ABS_TILT_{X,Y} axes so that a value of zero is reported when
the pen is vertical. Combined with resolution information in the next
patch, this makes it possible for userspace to calculate the pen angle
without needing hardware-specific knowledge. The xf86-input-wacom driver
was updated to support signed tilt values in late-2012 (2f2acec).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo models do not support HID_DG_CONTACTMAX. Plus, Bamboo pen-only
has touch descriptor. This leads to some complications in the code.
This patch also fixes duplicated PAD interfeaces for Intuos Pen
models.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Graphire 4 only has two tablet buttons; Bamboo Fun touch ring is only
for PAD.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ENODEV indicates no device is added. Hence, the associated pad input device
is simply freed.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
touch_input is stored in wacom_shared for pen data to report touch
switch status. It is possible, although we didn't see it happen on
Linux yet, that pen data is procesed before touch interface is
fully probed.
As a by-product of this patch, it fixes the FreeBSD issue reported
by Denis Akiyakov http://www.spinics.net/lists/linux-input/msg33971.html
Reviewed-by: Hans Petter Selasky <hps@selasky.org>
Tested-by: Denis Akiyakov <d.akiyakov@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.
This patch implements the pen support only. The finger part will come in
a later patch.
To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, tablets connected to the WL receiver all share the same
VID/PID. There is no way for the user space to know which one is which
besides parsing the name. We can force the PID to be set to the
actual hardware. This way, the input device will have the correct PID
which can be match in libwacom.
With only this trick, the pad input does not inherit the ID_INPUT_TABLET
udev property from its parent. We can force udev to accept it by declaring
a BTN_STYLUS which is never used.
This way, tablets connected through WL can be used from the user point of
view in the same way they are used while connected through wire.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wacom Cintiq Companion shares the same sensor than the Cintiq
Companion Hybrid, with the exception of the different PIDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A good point of this change is that now, the Intuos4 bluetooth can handle
the different tools (artpen, airbrush, mice), and we get a common interface
between USB and BT for accessing the LEDs/OLEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Reports the current status of the battery (discharging, charging, full).
- Also notify the upower daemon when there is a change in the battery
value.
- keep the battery value as a percentage, not the raw value
- add WACOM_QUIRK_BATTERY to easily add a battery to a device (required
for Bluetooth devices)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
