This makes easier to identify vendor ID, since AC97 vendors are
generally identified by 3 bytes. The remaining byte is used by the
vendor to identify its devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch properly implements audio handling on em28xx. Before this
patch, it was assumed that every device has an Empia 202 audio chip.
However, this is not true.
After this patch, specific AC97 chipset setup and configurations can be
done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the em28xx chip configuration register to determine whether
we have AC97 audio, I2S audio, or no audio support at all.
Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactor the em28xx IR support based on the em2860/em2880 and em2874
datasheets.
Tested on the HVR-950 (em2883), Pinnacle 800e (em2883), Pinnacle 80e (em2874)
using the remote controls that came with those products.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first em28xx were based on i2c IR's. However, some newer designs
are coming with a polling-based IR. Those are done by reading a register
set at em28xx.
This patch adds core polling support for those devices. Later patches will
add support for some device-specific IR's.
This patch adds the same basic IR polling code used by bttv, cx88 and saa7134, and
shares the common getkey masks defined at ir-common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add registration for Pinnacle 80e ATSC tuner
Register the em2874 based Pinnacle 80e device. Note that support for this
device also requires the new drx-j driver (which is not available yet)
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Thanks to Joerg Schindler from Pinnacle for providing sample hardware.
Thanks to Rainer Miethling from Pinnacle for providing engineering support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the logic so that the em28xx-alsa module does not get loaded for devices
that don't support analog audio (such as the em2874)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia moved the location of the GPIO/GPO registers in newer devices. Add the
ability to specify the relocated registers (including caching of register
contents).
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When setting up the device, remember the chip id, so we can control behavior
in the future without having to read the register continuously.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a EM28XX_NODECODER option to the list of available decoders. This option
becomes important for devices that do not have analog support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we have a polling task for IR, there's a race condition, since
IR can be polling while other operations are being doing. Also, we are
now sharing the same urb_buf for both read and write control urb
operations. So, we need a mutex.
Thanks to Davin Heitmueller <devin.heitmueller@gmail.com> for warning me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch, every register setup on em28xx were dynamically
allocating a temporary buffer for control URB's to be handled.
To avoid this ping-pong, use, instead a pre-allocated buffer.
Also, be sure that read control URB's also use the buffer, instead of
relying on a stack buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warnings. None are serious, but cutting down on these helps find
future serious sparse warnings/errors.
Redid the av7710.c patch based on a suggestion by Oliver Endriss.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two videomate boards supporded by em28xx. The names are almost
identical.
This patch renames one of such entries to something else.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- New supported IDs for analog models
(Based on Markus Rechberger <mrechberger@gmail.com> version of em28xx driver)
- Validation field for new em28xx boards.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
[mchehab@infradead.org: Need to fix some merge conflicts]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
em28xx-dvb.c
em28xx.h
- Add support for the ATI TV Wonder HD 600, based on a 94 email exchange and
USB traces provided by Ronnie Bailey
Thanks to Ronnie Bailey <purevw@wtxs.net> for testing the changes
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
em28xx-input.c
em28xx-video.c
em28xx.h
- Add support for the PointNix Intra-Oral Camera, which required addition of
a construct for reading the "snapshot" button (provided on the em2860 and
em2880 chips, but this is the first case where I have seen it actually used
in a product). The button is wired to pin 56 on the em2880.
http://www.pointnix.com/ENG/dental/product_02.asp
Thanks to Roberto Mantovani <rmantovani@libero.it> for testing the changes
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, HVR900/HVR950 were incorreclty going back to analog. The
result is that only digital were working.
This patch provides the proper setup for analog/digital and tuner callback.
It also properly resets analog into a sane state at open().
Thanks to Steven Toth <stoth@linuxtv.org> and Michael Krufky <mkrufky@linuxtv.org>
for helping to set the proper parameters to GPO/GPIO em2883 ports.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, all registers will follow the same convension:
EM28XX_R<reg_number>_<reg_name>
This allows to associate a register with its value, and also with a canonical
name. Also, registers that are specific to a given chip were renamed accordingly,
as EM2800_foo (for 2800 only registers) or EM2880_foo (for registers that started
to appear on em2880).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx.h contains lots of different stuff inside. The better is to break it on
some files.
This patch removes the register names, moving them to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is more conservative than just removing the msleep() from
em28xx_write_regs_req(), since some old hardware may still need it.
So, it will remove the sleep time only for those chips where this
removal were tested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Modifies em28xx-dvb not to use videobuf-dvb, but instead to include the code
for registering dvb devices locally and use the URB management code in the
em28xx driver directly. DVB data streaming should now work.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move the URB setup and management code to em28xx-core.c and generalise
it slighlty so that the DVB code can use it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c:
- Fix reversed val/rst values in both analog_gpio and digital_gpio
vectors
- Fix crash that would was occurring during every analog startup
while looping over gpio_ctl
- Remove what appears to be a redundant setting of gpio_ctl->val
- Don't use OREN538 demodulation for the HVR-950 (prevents ATSC
scanning from working)
em28xx-dvb.c:
- Tuner should be in digital mode when issuing the reset
- Add copyright
- Change struct definition (corresponds to fix in em28xx-cards.c for
gpio_ctl looping)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Devin Heitmueller <devin.heitmueller@gmail.com> and Aidan
Thornton" <makosoft@googlemail.com> for pointing some errors with the
previous scenario.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx based devices with xc3028 may require some specific gpio values.
This patch adds a generic handling for such values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds em28xx-dvb. This driver is highly based on cx88-dvb and
saa7134-dvb.
This code currently loads and unloads successfully. However, some
changes are needed to properly support the mpeg streams and to setup
em28xx to work on DVB mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes some fields from data structs.
There are some fields that are just caching some calculus for buffer
size. The calculus were moved to the places it were needed and the now
unused fields were removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes three related issues and a fourth trivial one:
- Use buffers even if no-one's currently waiting for them (fixes
underrun issues);
- Don't return incomplete/mangled frames at the start of streaming and
in the case of buffer underruns;
- Fix an issue which could cause the driver to write to a buffer that's
been freed after videobuf_queue_cancel is called (exposed by the
previous two fixes - for some reason, ignoring buffers that weren't
being waited on worked around the issue);
- Fix a bug which could cause only one field to be filled in the first
buffer (or first few buffers) after streaming is started.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It fixes a couple of minor bugs, comments out a bogus BUG_ON, sets fh->type
correctly, uses dev->width and dev->height for now, and adds a missing spinlock
init (nasty - caused a system lockup). It also adds some debug code which
probably isn't all that useful. I haven't tested this version of the patch yet,
though, so I'm not sure what you can expect if you try it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The usage of videobuf-vmalloc allows to cleanup em28xx logic.
Also, it reduced its size by about 5.42% on i386 arch (and about 7.5% on x86_64):
39113 4876 40 44029 abfd old/em28xx.ko
36731 4868 40 41639 a2a7 /home/v4l/master/v4l/em28xx.ko
Also, the preliminary tests, made on a single core 1.5 MHz Centrino showed
that CPU usage reduced from 42%-75% to 28%-33% (reports from "top") command.
A test with time command presented an even better result:
This is the performance tests I did, running code_example to get 1,000 frames
@29.995 Hz (about 35 seconds of stream), tested on a i386 machine, running at
1,5GHz:
The old driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:34.21: 8.22s User time, 25.16s Kernel time, 97% CPU used
The videobuf-based driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:35.36: 0.01s User time, 0.05s Kernel time, 0% CPU used
Conclusion:
The time consumption to receive the stream where reduced from about 33.38
seconds to 0.05 seconds.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.
Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=480/800 us (60%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=232/800 us (29%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- em28xx-core.c:em28xx_write_reg_bits()
- em28xx-video.c:em28xx_vdev_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
has_tuner flag doesn't make much sense, since tuner_type=TUNER_ABSENT
means the same thing.
Having two ways to say that a tuner is not present is
not nice, since it may lead to bad setups. In fact, with the previous
code, if a device were using has_tuner=0, but the user forces a tuner,
with modprobe option tuner=type, the modprobe option won't work.
Also, tveeprom returns TUNER_ABSENT, when tuner is unknown or absent.
So, with the previous logic, in this case, the driver should set
has_tuner=0, or has_tuner=1 otherwise.
Instead of adding several additional tests and setups, better just to
remove .has_tuner.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
