This event will be generated by the target for packet completions.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new cookie field that would be filled by the host.
This can be used to match the TX status WMI event with
the appropriate packet.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current max queue length of 1024 is quite large
and unnecessary. 256 suffices well enough even for high
throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For all packets sent through the USB_WLAN_TX_PIPE endpoint,
the private area of the SKB's tx_info can be used to store
driver-specific information. For packets sent through USB_REG_OUT_PIPE,
this will not make a difference since they are routed through a
separate routine that doesn't access the private region.
This would help in situations where TX information is required
in the URB callback.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.
Fix this by adjusting the beacon response time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the rx/tx tasklet is pending, new unnecessary interrupts may arrive.
Decrease the load by temporarily disabling the interrupts until the tasklet
has completed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pointers to the debugfs entries do not need to be saved, because they
will be recursively removed when the wiphy is unregistered.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reusing the configured retry counts from the skb cb is more efficient than
reloading the data from uncached memory.
Replace ts_longretry (unused) with ts_final_retry which contains the retry
count for the final rate only
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is no longer necessary for preparing mac80211 tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.
This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.
To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.
Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.
Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory. This patch corrects that oversight.
Reported-by: Eugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update Tx gain 23 for all tx gain table.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
