Currently there are two different implementations (in the firmware) for
the QAM demodulator command: one takes 4 and the other takes 2
parameters. The driver shows an error in dmesg When using the
4-parameter command with firmware that implements the 2-parameter
command. Unfortunately this happens every time when chaning the
frequency (on DVB-C).
This patch simply makes configurable, how many command parameters will
be used. All existing drxk_config instances using the "drxk_a3.mc" were
updated because this firmware is the only loadable firmware where the
QAM demodulator command takes 4 parameters. Some firmwares in the ROM
might also use it. The drxk instances in the em28xx-dvb driver were also
updated to silence the warnings.
If no qam_demod_parameter_count is given in the drxk_config struct, then
the correct number of parameters will be auto-detected.
[mchehab@redhat.com: Fix a small CodingStyle issue at one comment]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating two DVB frontend entries for the same device,
create just one entry, and fill the delivery_system according with
the supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.
Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If those demods are unselected, but a bridge driver requires them,
produce a runtime message, instead of missing symbols.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver is too limited: it assumes that UIO is used only for
controlling the antenna, and that only UIO-1 is in usage. However,
from Terratec H7 driver [1], 3 UIO's can be used. In fact, it seems
that H7 needs to use all 3. So, make the code generic enough to handle
the most complex scenario. For now, only antena GPIO can be specified,
but is is easier now to add the other GPIO/UIO needs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Terratec H5 doesn't require to switch mode, but generates
an error due to this logic. Also, GPIO's are board-dependent.
So, add it at the board config struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On em28xx, tda18271C2 is accessible when the i2c port
is not touched. Touching on it breaks the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The microcode firmware provided on Terratec H5 seems to be
different. Add a parameter to allow specifying a different
firmware per-device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using #ifdef I2C_LONG_ADR for some devices, convert
it into a parameter. Terratec H5 logs from the original driver
seems to need this mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the only parameter to be configured is the I2C
address. However, Terratec H5 logs shows that it needs a different
setting for some things, and it has its own firmware.
So, move the addr into a config structure, in order to allow adding
the required configuration bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for the DRX-K DVB-C/T demodulator.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
