This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.
The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.
As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Exposes the ADC device present on, at least, Intel Merrifield platform.
Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>
Though it has been heavily rewritten for upstream.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS0 6-axis (acc + gyro) Mems sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix typos in gyro gain definitions for LSM9DS1 sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change replaces indio_dev's mlock with the driver's own lock. The lock
is mostly needed to protect state when changing the `dac_cache` info.
The lock has been extended to `ad7303_read_raw()`, to make sure that the
cache is updated if an SPI-write is already in progress.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On LSM6DSO/LSM6DSR/LSM6DSOX/ASM330LHH and ISH330DHCX
devices it is possible to trim the hardware timestamp
resolution through the FREQ_FINE[7:0] bits of the
INTERNAL_FREQ_FINE register, which contains the difference
in percentage of the effective ODR (and timestamp rate)
with respect to the typical value.
The formula for calculating the effective ODR reported
in the application notes has been linearized to the first
order to simplify the calculation (pls. see note on source
code).
This change may be useful in the outcome of CTS
tests regarding the SingleSensorTests and the
SensorTest#testSensorTimeStamps for high ODRs
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable drdy mask if available in order to mark invalid samples during
sensor bootstrap phase
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for runtime PM & sleep.
Provide pclk to regmap as registers access doesn't need full power
(e.g. regulator). Always restore HFSEL when resuming. It may get lost
depending on low power level that has been achieved.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing wake-up register info for LSM6DSO/LSM6DSOX sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing kernel doc for st_lsm6dsx_hw data structure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warnings:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
WARNING: line over 80 characters
+ if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source"))
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always grub conf mutex in st_lsm6dsx_write_event_config since it can run
concurrently with FIFO configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_update_bits_locked in st_lsm6dsx_write_event and
st_lsm6dsx_event_setup routines since they can run concurrently with
sensor hub configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if enable_reg of event_settings data structure is defined before
writing on it
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bdu, boot and reset register definitions in hw_settings register
map since not all supported sensors (e.g lsm9ds1) rely on the same
definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move active low and open drain register definitions in hw_settings
register map since not all supported sensors (e.g lsm9ds1) rely on the
same definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check read_fifo pointer before using it since we can't assume it
is always set adding new sensors. This patch fixes the following crash:
irq 277: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc5-00322-g792b824-dirty #7
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0112750>] (unwind_backtrace) from [<c010d018>] (show_stack+0x10/0x14)
[<c010d018>] (show_stack) from [<c0c2bfc8>] (dump_stack+0xd8/0x10c)
[<c0c2bfc8>] (dump_stack) from [<c01923fc>] (__report_bad_irq+0x24/0xc0)
[<c01923fc>] (__report_bad_irq) from [<c0192820>] (note_interrupt+0x27c/0x2dc)
[<c0192820>] (note_interrupt) from [<c018f174>] (handle_irq_event_percpu+0x54/0x7c)
[<c018f174>] (handle_irq_event_percpu) from [<c018f1d4>] (handle_irq_event+0x38/0x5c)
[<c018f1d4>] (handle_irq_event) from [<c0193664>] (handle_level_irq+0xc8/0x154)
[<c0193664>] (handle_level_irq) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c053c348>] (mxc_gpio_irq_handler+0xc4/0xf8)
[<c053c348>] (mxc_gpio_irq_handler) from [<c053c3e0>] (mx3_gpio_irq_handler+0x64/0xb8)
[<c053c3e0>] (mx3_gpio_irq_handler) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c018e550>] (__handle_domain_irq+0x64/0xe0)
[<c018e550>] (__handle_domain_irq) from [<c0529610>] (gic_handle_irq+0x4c/0xa0)
[<c0529610>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
Exception stack(0xc1301f10 to 0xc1301f58
1f00: 00000001 00000006 00000000 c130c340
1f20: c1300000 c1308928 00000001 c1308960 00000000 c12b9db0 c1308908 00000000
1f40: 00000000 c1301f60 c0182010 c0109508 20000013 ffffffff
[<c0101a70>] (__irq_svc) from [<c0109508>] (arch_cpu_idle+0x20/0x3c)
[<c0109508>] (arch_cpu_idle) from [<c015ed70>] (do_idle+0x1bc/0x2bc)
[<c015ed70>] (do_idle) from [<c015f204>] (cpu_startup_entry+0x18/0x1c)
[<c015f204>] (cpu_startup_entry) from [<c1200e68>] (start_kernel+0x440/0x504)
[<c1200e68>] (start_kernel) from [<00000000>] (0x0)
handlers:
[<62052c0d>] st_lsm6dsx_handler_irq threaded
[<f2004b92>] st_lsm6dsx_handler_thread
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Tested-by: Bobby Jones <rjones@gateworks.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event since
it can run concurrently with sensor hub configuration. Move event
related code in st_lsm6dsx_report_motion_event
Fixes: 1aabad1fb5 ("iio: imu: st_lsm6dsx: add motion report function and call from interrupt")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max1027/29/31 series returns the measured voltages with a
resolution of 10 bits. There is a very similar series, max1227/29/31
which works identically but uses a resolution of 12 bits. Prepare the
support for these chips by turning the 'depth' into a macro parameter
instead of hardcoding it everywhere. Also reorganize just a bit the
macros at the top to avoid repeating tens of lines when adding support
for a new chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip has a 'start conversion' and a 'end of conversion' pair of
pins. They can be used but this is absolutely not mandatory as regular
polling of the value is totally fine with the current internal
clocking setup. Turn the interrupts optional and do not error out if
they are not inquired in the device tree. This has the effect to
prevent triggered buffers use though.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, only write operations were supported. Force two bytes read
operation when reading, which should fit most of the development
purposes. Of course, extended operations like buffered reads on
multiple channels or even temperature + voltage reads will not be read
entirely. Usually, just starting a new operation will work but in any
case a software reset (done through the debufs interface too) will
return the device in a usable state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for Analog Devices ADUX1020 Photometric sensor.
Only proximity mode has been enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
-----BEGIN PGP SIGNATURE-----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=nIWU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, cleanups and features for the 5.5 cycle
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (41 commits)
iio: pressure: bmp280: remove stray newline
iio: adc: sc27xx: Use devm_hwspin_lock_request_specific() to simplify code
iio: chemical: atlas-ph-sensor: fix iio_triggered_buffer_predisable() position
iio: gyro: clean up indentation issue
counter: stm32: clean up indentation issue
iio: proximity: sx9500: fix iio_triggered_buffer_{predisable,postenable} positions
iio: core: Add optional symbolic label to device attributes
dt-binding: iio: Add optional label property
iio: gyro: adis16080: replace mlock with own lock
counter: stm32-lptimer-cnt: fix a kernel-doc warning
counter: stm32-timer-cnt: fix a kernel-doc warning
iio: gyro: adis16130: remove mlock usage
MAINTAINERS: add entry for ROHM BH1750 driver
dt-bindings: iio: light: bh1750: convert bindings to yaml
iio: imu: st_lsm6dsx: add motion report function and call from interrupt
iio: imu: st_lsm6dsx: always enter interrupt thread
iio: imu: st_lsm6dsx: add wakeup-source option
iio: imu: st_lsm6dsx: add motion events
iio: imu: st_lsm6dsx: move interrupt thread to core
iio: imu: inv_mpu6050: add fifo support for magnetometer data
...
Remove a stray newline from the probe callback.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change to use devm_hwspin_lock_request_specific() to help to simplify the
cleanup code for drivers requesting one hwlock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
The position of iio_triggered_buffer_postenable() is correct.
Note this is not stable material. It's a fix in the logical
model rather fixing an actual bug. These are being tidied up
throughout the subsystem to allow more substantial rework that
was blocked by variations in how things were done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a return statement that is indented incorrectly, add in
the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
This change re-organizes things a bit so that the postenable & predisable
are symmetrical. It also converts the preenable() to a postenable().
Not stable material as there is no known problem with the current
code, it's just not consistent with the form we would like all the
IIO drivers to adopt so as to allow subsystem wide changes.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
