Use SMP safe del_timer_sync instead of del_timer for cancelling
timers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed following warnings-
drivers/net/wireless/airo.c:39: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/wireless/airo.c:48: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a relatively old Prism2 card which is correctly supported
by the hostap driver.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logically, config B43_BCMA_PIO should depend on B43. This also solves
the problem that sub options of b43 driver didn't indent correctly in
make menuconfig's ncurses window.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 0baa0fd76f
("rtlwifi: Convert core routines for addition of rtl8192se and
rtl8192de") removed setting HW_VAR_RCR, HW_VAR_MGT_FILTER and
HW_VAR_CTRL_FILTER. The last two are probably done because some hardware
does not support them. The first is probably a mistake. This patch adds
the missing set_hw_reg call.
For PCI support, rx_conf is not touched directly. Instead, get_hw_reg is
used to abstract between receive_config (for PCI) and rx_conf (for USB).
This was tested on a 10ec:8176 Realtek RTL8188CE (according to the
label on the mini-PCIe card). Before this patch, `iw wlan0 set monitor
otherbss` did not capture frames from other BSS's. After this patch, it
does print packets.
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtl*_set_check_bssid functions are mostly the same, but access the
RCR register in different ways. Use the get_hw_reg abstraction layer
(which reads rtlpci->receive_config for PCI devices and mac->rx_conf for
USB).
There is no functional change for cases where receive_config was
accessed directly. For rtl8192ce, there is still no change because
nothing modifies REG_RCR or receive_config. For rtl8192cu, it now also
applies changes to rx_conf from configure_filter, but that can be
considered a bug which is fixed later.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a typo here because the names are confusingly similar. The
intent was sizeof(struct ieee80211_vht_cap) (size 12) but sizeof(struct
ieee80211_ht_cap) (size 32) was used.
Anway, it's cleaner to just specify the variable instead of the type.
Fixes: 5f6d598339 ('mwifiex: add VHT support for TDLS')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the TLV flags as a handshake between the firmware
and the driver. These flags allow the firmware to advertise
its capabilities and API version.
Since we are running short of bits, we add a new
infrastructure which is more scalable, yet backward
compatible.
We make now the difference between API changes and the
capabilities. Both can have an index which allows to scale
at will.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Collect statistics regarding rates and aggregations in Rx
frames and export the data via debugfs.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer firmware support a new bit in the policy that allows
to request to apply the time event immediately. Add this bit
without removing the workarounds we used until now to support
older firmares.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case the firmware didn't assert but we want to restart
it, e.g. we didn't get the reply for a host command, or the
Tx queues are stuck, we should stop the firmware by
provoking an interrupt. This allows to better debug the
firmware in these bad scenarios.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.
Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.
The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.
Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.
Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the min wl18xx fw version to 8.8.0.0.13
This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.
Some modifications were done to the driver-fw api
in order to support multiple APs.
Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.
Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.
Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.
However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.
This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.
Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.
Such case will cause consecutive recoveries due to
command execution failures.
While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_channel_to_frequency() to replace b43_channel_to_freq_{2,5}ghz(),
and remove unused b43_freq_to_channel_{2,5}ghz().
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new API for ALIVE notification was misunderstood.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support the changes below:
- Fields and sections structure were changed.
- the NVM file built from DWord instead of Words.
- sections header format was changed.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New FW enables support for power save on BSS and P2P client MACs
simultaneously when they function on different channels (DCM).
Enable this case in the driver after examining new TLV flag -
IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM. Still power management is not
allowed on both MACs if they function on a same channel.
Remove another redundant TLV flag - IWL_UCODE_TLV_FLAGS_P2P_PS that
is not in use anymore. Remove bound_vif_cnt as redundant.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow reading/writing prph registers.
The address is set in the first argument
of the write operation. second argument
is optional and can be used for writing.
e.g.
echo '0xA01234 0x99' > /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will write 0x99 into reg 0xA01234
cat /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will show its current value (probably 0x99)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking the SKB protocol against EAP, check the
IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag that more generally
indicates whether or not the frame is a port control frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to get sniffer captures with correct
settings for these HT / VHT capabilities.
Also set the corresponding HAVE_MCS / VHT_KNOWN bits in
the registration to mac80211.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The various code blocks in iwl_pcie_[rt]xq_inc_wr_ptr
finally do the same things, so just merge them
all and make the functions cleaner.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to parse FW API version TLVs.
Currently only API version for key_material is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During deauthenticate/link lost event, disable all TDLS links as
TDLS would not work when infra connection is not active.
Also this will avoid an issue where ping to peer station doesn't
work after reassociation to AP where we had created TDLS link in
earlier association.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If TDLS link is 11ac enabled i.e. we as well as peer station
supports VHT, configure seprate TX & RX window sizes during
BA setup. So even if BSS does not support 11ac, we can use VHT
capabilities and higher window sizes on direct link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During TDLS setup request/response, if HW is 11ac capable,
we add VHT Capability IEs in outgoing data frame. Also while
processing received setup request/response, we preserve peer's
11ac capability retrieved from IEs.
Patch also gets VHT parameters from config_station handlers and
sets it to FW using TDLS config command.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mwifiex_fill_vht_cap_tlv function to pass
struct ieee80211_vht_cap instead of mwifiex_ie_types_vhtcap
so that it can be used generically.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds AMPDU support for TDLS link. We have set 11n
capabilities including AMPDU parameters during ENABLE_LINK.
We set a variable in RA list to indicate this as TDLS link.
This patch uses these capabilities to know if AMPDU is allowed
on TDLS link and enables AMPDU aggregation for TX and RX reording
support for RA list for this peer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. If data packet is addressed to TDLS peer for which link is
established, mark these packets with TDLS flag so that FW can
send them on direct link instead of sending via AP.
2. If data packet is addressed to TDLS peer and TDLS setup is
underway, move these packets to TDLS queue.
3. If this packet is TDLS setup packet, do not block it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While TDLS link is being setup, few packets from this station to
peer station may be buffered at AP. It may happen that once TDLS
link is setup, packets sent from station to peer on direct link
get delivered before traffic from AP arrives at peer station.
This results into packet reordering issue at peer station.
To avoid this, we hold data packets destined to TDLS peer during
TDLS setup. These packets are moved to temperory TDLS TX queue.
Upon successful TDLS setup, they are moved to RA list created for
this peer. Upon failure, packets are moved back to AP's RA list
for that particular TID.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass 'struct ieee80211_ht_cap' pointer to
mwifiex_fill_cap_info() instead of
'struct mwifiex_ie_types_htcap' pointer, because the routine
internally uses the later one.
This patch also adds WARN_ON_ONCE check for NULL band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are now needed by TDLS while managing station list.
Move them from AP related file to utility file.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tos_to_tid_inv values are needed even during TDLS restore
operations. Currently tos_to_tid_inv is part of wmm.c and
is declared static.
Make it part of private structure so that it can be used in
other files as well.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where we were checking for AP's AMPDU param
setting even when transmitting traffic to associated station.
Patch adds provision to pass additional parameter ra_list pointer
to function which checks if AMPDU is allowed. If current BSS type is
AP, we check station's AMPDU params else we check AP's AMPDU params.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently MU/SU beamformer and MU beamformee features are
not supported.
Hence this patch modifies VHT capability information accordingly.
Number of sounding dimensions should be zero in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that beamforming capability field in
ht capability info gets filled if hardware supports the feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
