This SSP Controller supports a number of serial communication methods
and as such cannot be registered using of_register_spi_devices.
Instead we register it simply as a primecell device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This provides PL310 Level 2 Cache Controller Device Tree
support for all u8500 based devices.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enables the 3 UARTs found on a u8500 using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the embedded GIC on all u8500 based hardware using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.
This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This lets us move over evertything to device tree one by one.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This provides very basic Device Tree support for ST-Ericsson's
low-cost development platform, Snowball. If Device Tree for
ux500 is enabled and the correct board is configured within the
Device Tree blob, the correct *_init_machine() will be called.
This patch is based on some original work completed by:
Niklas Hernaeus <niklas.hernaeus@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mach-ux500/timer.c lacked the inclusion of mach/irqs.h, and thus
failed to compile. Fix it and also remove an unused variable.
Test compiled only.
Reported-by: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergman <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the new smp_twd runtime registration interface
to the ux500 platforms, and remove the old compile-time support.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* ux500/timers:
ARM: plat-nomadik: modernize MTU timer
ARM: plat-nomadik: handle clocking properly
ARM: plat-nomadik: get rid of global mtu base pointer
These are no longer required since a 'parent' pointer is now
passed to each registering device.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we make use of the new System-On-Chip bus driver to export
vital SoC information out to userspace via sysfs. This patch
provides a data structure of strings to populate the base
nodes found in:
/sys/devices/soc[0|1|2|...]/[family|machine|revision|soc_id].
It also adds one more node as requested by ST-Ericsson.
'process' depicts the way in which the silicon was manufactured.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pass the base offset to the Nomadik MTU timer in the init call
instead of keeping a global pointer to be assigned.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (31 commits)
ARM: 7304/1: ioremap: fix boundary check when reusing static mapping
ARM: 7301/1: Rename the T() macro to TUSER() to avoid namespace conflicts
ARM: 7299/1: ftrace: clear zero bit in reported IPs for Thumb-2
ARM: 7298/1: realview: fix mapping of MPCore private memory region
PCMCIA: fix sa1111 oops on remove
ARM: 7288/1: mach-sa1100: add missing module_init() call
ARM: 7297/1: smp_twd: make sure timer is stopped before registering it
ARM: 7296/1: proc-v7.S: remove HARVARD_CACHE preprocessor guards
ARM: 7295/1: cortex-a7: move proc_info out of !CONFIG_ARM_LPAE block
ARM: 7293/1: logical_cpu_map: decouple CPU mapping from SMP
ARM: 7291/1: cache: assume 64-byte L1 cachelines for ARMv7 CPUs
ARM: 7290/1: vmlinux.lds.S: align the exception fixup table to a 4-byte boundary
ARM: 7289/1: vmlinux.lds.S: do not hardcode cacheline size as 32 bytes
MFD: ucb1x00-ts: fix resume failure
MFD: ucb1x00-core: fix gpiolib direction_output handling
MFD: ucb1x00-core: fix missing restore of io output data on resume
MFD: mcp-core: fix mcp_priv() to be more type safe
MFD: mcp-core: fix complaints from the genirq layer
Revert "ARM: sa11x0: Implement autoloading of codec and codec pdata for mcp bus."
Revert "ARM: sa1100: Refactor mcp-sa11x0 to use platform resources."
...
Fix up conflict due to arch/arm/mach-mx5/Kconfig having been merged into
mach-imx5 (commit 784a90c0a7: "ARM i.MX: Merge i.MX5 support into
mach-imx"), but the ARM_L1_CACHE_SHIFT_6 entry was moved to be driven by
the CPU_V7 logic from it in the old location in rmk's branch (commit
a092f2b153: "ARM: 7291/1: cache: assume 64-byte L1 cachelines for
ARMv7 CPUs").
It turns out that the logical CPU mapping is useful even when !CONFIG_SMP
for manipulation of devices like interrupt and power controllers when
running a UP kernel on a CPU other than 0. This can happen when kexecing
a UP image from an SMP kernel.
In the future, multi-cluster systems running AMP configurations will
require something similar for mapping cluster IDs, so it makes sense to
decouple this logic in preparation for this support.
Acked-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MMC_CAP_SD_HIGHSPEED is not supported on Snowball board resulting on
initialization errors.
Cc: stable@kernel.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This applies ARM errata 764369 for all ux500 platforms.
Cc: stable@kernel.org
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Invalidating outer cache without disabling it is a big
nono, and so, remove the machine specific outer.inv_all
And at the same time it does not prevent us overriding
outer.disable as we do not have any such secure SMI to
handle the same while kexec disables the outer cache.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change is needed after 622859634 "usb: musb: drop a
gigantic amount of ifdeferry", where CONFIG_USB_MUSB_PERIPHERAL
& CONFIG_USB_MUSB_HOST has been removed.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Once the ENDPROC is in place, BSYM() in not longer necessary
to get correct pointer to u8500_secondary_startup().
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch_reset() is deprecated; systems should hook into system restart via
the 'restart' method in the platforms machine description record.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add default value for CONFIG_ARCH_NR_GPIO to Kconfig and remove the
definition in gpio.h. We can't remove gpio.h yet as asm/gpio.h still
includes it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clock for the smp_twd block is not equal to the CPU
frequency, actually it is divided by two, so fix this,
and set the initial frequency to half of 1GHz which is
the most common case.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DB8500 ED (Early Drop) and V1 are only available inside of
ST-Ericsson or partners, we have actively replaced and scrapped
these prototypes. All Nova products on the open market (such as
the Snowball board) are based on V2 and later ASIC variants.
So let us focus on supporting the silicon that will be used and
delete this to get a clear overview.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use platform_device_register_simple() rather than a static
struct, so we create and register the PMU device on-the-fly.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a few CPU identification functions for the U5500 variants.
Contains portions of code written by Rabin Vincent.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extend the ux500 ID table to cover the DB8520 variant.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The overlapping iotable mapping entries for the ux500 Cortex
A9 SCU, CPU control and TWD are no longer accepted by the
kernel. Remove the overlaps so the machine boots again.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a more complete list of the MOP500 GPIO pins, especially
for those used with the Snowball board. Sort GPIO number in
falling number order so there is some structure to this file.
Fix some whitespace issues in the process.
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds device sdi1 for ST-Ericsson HREFv60 and later to enable
the possiblity of using the onboard CW1200 chip for WLAN.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Properly support the correct SDI-init sequence on the
ST-Ericsson HREFv60 and later boards in order to get
support for SD cards.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert the ux500 platforms to be using the gic_handle_irq
function as their primary interrupt handler.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
