after the most recent patches, the driver was not using the
correct iterator for updating the receive address registers (RAR)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rename the cryptic "dca_capable" to "dca_capable_firmware"
and "dca_enabled" to "dca_device_present" in the firmware
counters.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Stop scaring people with what looks like a fatal message when DCA support
is compiled into their kernel, but the DCA device is not present.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the bad usage of udelay(5000), which in turns is a
mdelay(5). It causes compilation for ARM where udelay maximum value
is checked.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int. This results in warnings from min() on 64-bit
architectures where they are different. Add a cast to make it match.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This should avoid an interrupt storm, which has been observed in the
field with one faulty board.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This prevents speculative reading of the statistics before the
completion flag.
From: Neil Turton <nturton@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
mdio_clause45_links_ok() correctly checks efx_phy_mode_disabled(), so
tenxpress_link_ok() doesn't need to.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On some boards 10Xpress feeds a 156 MHz clock to the Falcon XMAC. MAC
statistics DMA can fail while this clock is stopped during a PHY reset.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a bug in XAUI synchronisation in early 10Xpress firmware
versions. This is fixed in released firmware and we do not need to
work around it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Match pci_request_region() with pci_release_region(), not
release_mem_region().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I would like to submit a correction to the driver
drivers/net/8139too.c,
which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!
Mats Erik Andersson, meand@users.sourceforge.net
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN doesn't work except if you'd opened the interface in promiscuous
mode before. This happens because VLAN tag stripping is not correctly
marked as enabled at device startup
Also, the vlan_strip_flag field was moved to the private network
structure.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
release_irq label is only used when ALLOW_DMA is defined.
drivers/net/cs89x0.c: In function 'net_open':
drivers/net/cs89x0.c:1401: warning: label 'release_irq' defined but not used
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hso_serial_common_free() mustn't be called if
hso_serial_common_create() fails.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WAN: fixes a NULL dereference in hdlc_x25.
Reported-by: Adrian Bunk <bunk@kernel.org>.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IPv6 all-node-multicasts and DAD probes should not be tx-balanced
on ALB/TLB bonds. The all-node-multicast is an equivalent to IPv4
broadcasts. DAD probes have to be sent only on the primary so that
we don't get false-positive detections.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Lockdep warns about the mdio_lock taken with interrupts enabled then later
taken from interrupt context. Initially, I considered changing these
to spin_lock_irq/spin_unlock_irq, but then I looked at atl1e_phy_init()
and saw that it calls msleep(). Sleeping while holding a spinlock is
not allowed either.
In the probe path, we haven't registered the interrupt handler, so
it can't poke at this card yet. It's before we call register_netdev(),
so I don't think any other threads can reach this card either. If I'm
right, we don't need a spinlock at all.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ehea busmap must be allocated only once in the first of many calls of the
ehea_create_busmap_callback.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A call to pnp_stop_dev and pnp_start_dev now shuts down and
initializes plug and play devices for suspend and resume.
Signed-off-by: David Fries <david@fries.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Seems like the spinlock for the AU1x00 ethernet device is initialised too
late, as it is already used in enable_mac(), which is called via
mii_probe() before the init takes place.
The attached patch is working here for a Linux Au1100 2.6.22.6 kernel,
and as far as I checked should also be applicable to the current head
(just line numbers differ).
Signed-off-by: Martin Gebert <Martin.Gebert@alpha-bit.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sparc32 allmodconfig with linux-next:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:164: error: 'PAGE_KERNEL' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:164: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:164: error: for each function it appears in.)
this is due to some header shuffle in linux-next. I didn't look to see what
it was. I'd sugges that this patch be merged ahead of a linux-next merge to
avoid bisection breaks.
We strictly only need asm/pgtable.h, but going direct to asm includes always
seems grubby.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Self-baked macros cause bunch of compile warnings like below:
CC [M] drivers/net/skfp/pmf.o
CC net/ipv4/fib_semantics.o
drivers/net/skfp/pmf.c:86: warning: cast from pointer to integer of different size
drivers/net/skfp/pmf.c:87: warning: cast from pointer to integer of different size
...
Use the standard offsetof() macro instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 159198862a added SMC_IO_SHIFT
platform data support. After that ARM board support was added.
The default case is still missing though, so on SuperH SMC_IO_SHIFT
is constantly zero regardless of what you pass as platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Test-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit c4f0e76747 added nowait platform
data support. The printout code was however not updated, so the value
of SMC_NOWAIT is still used. This patch makes sure that nowait is printed
accordingly to platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- the register is defined for the 8169 chipset only and there is
no 8169 beyond RTL_GIGA_MAC_VER_06.
- only the lower 3 bytes of the register are valid
Fixes:
1. http://bugzilla.kernel.org/show_bug.cgi?id=10180
2. http://bugzilla.kernel.org/show_bug.cgi?id=11062 (bits of)
Tested by Hermann Gausterer and Adam Huffman.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix typo in ehea_h_query_ehea() which prevents building when DEBUG is on.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The de2104x did a pci_disable_device() in it's close function, but
the open function never does a pci_enable_device() and assumes that
the device is already enabled. Considering that downing the interface
is just a temporary thing the pci_disable_device() isn't a pretty good
idea and removing it from the close function just fixes the bug.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reported by Thomas Graf.
If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.
Add __skb_unlink() call to fix that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob looks like this...
__le16 load_address
unsigned char data[]
[akpm@linux-foundation.org: include vmalloc.h]
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
In the case of the file drivers/atm/eni.c, I am a little bit suspicious of
the -1 at the end of the affected expression. Please check that that is
what is wanted.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_mb is enough for ordering memory operations among processors,and mb is
more expensive than smp_mb for UP machine, so replace it with smp_mb().
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format used by
lspci(8).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove noop VFS stubs. The VFS does that on a NULL pointer anyways.
- Fix timer handler prototype to be correct
- Comment ugly SMP race I didn't fix.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found two possible bugs where the z1 value was used directly without
byteswapping.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling capi_ctr_get, error handling code should call capi_ctr_put.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S;
position p1,p2,p3;
@@
(
if ((x = capi_ctr_get@p1(...)) == NULL || ...) S
|
x = capi_ctr_get@p1(...)
... when != x
if (x == NULL || ...) S
)
<...
if@p3 (...) { ... when != capi_ctr_put(x)
when != if (x) { ... capi_ctr_put(x); ...}
return@p2 ...;
}
...>
(
return x;
|
return 0;
|
x = E
|
E = x
|
capi_ctr_put(x)
)
@exists@
position r.p1,r.p2,r.p3;
expression x;
int ret != 0;
statement S;
@@
* x = capi_ctr_get@p1(...)
<...
* if@p3 (...)
S
...>
* return@p2 \(NULL\|ret\);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This minor cleanup simplifies later changes which will convert
struct sk_buff and friends over to using struct list_head.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following build warning:
drivers/net/qlge/qlge_main.c:3897: warning: ‘qlge_resume’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/qlge/qlge_dbg.c: In function ‘ql_dump_qdev’:
drivers/net/qlge/qlge_dbg.c:369: warning: cast to pointer from integer of different size
drivers/net/qlge/qlge_dbg.c:373: warning: cast to pointer from integer of different size
drivers/net/qlge/qlge_dbg.c: In function ‘ql_dump_tx_ring’:
drivers/net/qlge/qlge_dbg.c:457: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:461: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c: In function ‘ql_dump_rx_ring’:
drivers/net/qlge/qlge_dbg.c:557: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:565: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:575: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:579: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:598: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
drivers/net/qlge/qlge_dbg.c:602: warning: format ‘%llx’ expects type ‘long long unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch mv643xx_eth from using drivers/net/mii.c to using phylib.
Since the mv643xx_eth hardware does all the link state handling and
PHY polling, the driver will use phylib in the "Doing it all yourself"
mode described in the phylib documentation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code. This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
If we don't poll the hardware statistics counters at least once every
~34 seconds, overflow might occur without us noticing. So, set up a
timer to poll the statistics counters at least once every 30 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When the IP header doesn't start 14, 18, 22 or 26 bytes into the packet
(which are the only four cases that the hardware can deal with if asked
to do IP checksumming on transmit), invoke the software checksum helper
instead of letting the packet go out with a corrupt checksum inserted
into the packet in the wrong place.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
We have to explicitly tell the hardware to include the pseudo-header
when doing receive checksumming, otherwise hardware checksumming will
fail for every received packet and we'll end up setting CHECKSUM_NONE
on every received packet.
While we're at it, when skb->ip_summed is set to CHECKSUM_UNNECESSARY
on received packets, skb->csum is supposed to be undefined, and thus
there is no need to set it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The timer_interval field is only assigned once, and never reassigned.
We can safely replace all instances of the timer_interval with a
constant value.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of the board is only used during the initialization of
the adapter. We can save the space of a pointer by not storing
this information.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_mac_link() doesn't need to return any error codes. And
all the callers don't check the return code. It is safe to
change the return type to a void.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CC [M] drivers/net/wireless/libertas/wext.o
drivers/net/wireless/libertas/wext.c: In function ‘lbs_get_rts’:
drivers/net/wireless/libertas/wext.c:307: warning: comparison is always
false due to limited range of data type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use min_t to avoid warnings when the typesafe version is used.
Explicitly cast u64s to unsigned long long when being passed to printk.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This paves the way for dynamic radio additions while the module
is loaded. Also restrict the number of radios to 100 because
creating that many already takes forever.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WPA requires that the PTK is installed immediately after the 4-way handshake
in order to properly decrypt the subsequent incoming EAPOL-GTK frame. If the
PTK is not enabled by the time the EAPOL-GTK frame arrives, the frame is
dropped and the supplicant does not receive the group key.
This will happen with fast Access Points that send the EAPOL-GTK frame before
the suplicant has successfully installed and enabled the PTK. To mitigate
this situation, this patch simplifies and accelerates the SIOCSIWENCODEEXT
execution.
This patch resolves OLPC ticket 7825 (http://dev.laptop.org/ticket/7825)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of QoS parameters.
Reported-by: Lorenzo Nava, Francesco Gringoli
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MODULE_FIRMWARE statement for 3945 HW.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MODULE_FIRMWARE statement for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates PCI IDs for 5350 Wifi/WiMax.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need, at worst ieee80211_start_tx_ba_session
will log a message when debugging is enabled, and poking such
internals of mac80211 definitely doesn't belong into an RC
algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control algorithms may need access to a station's
HT capabilities, so share the ht_info struct in the
public station API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_info->txrate_idx member isn't used by all RC algorithms
in the way it was intended to be used, move it into those that
require it (only PID) and keep track in the core code of which
rate was last used for reporting to userspace and the mesh MLME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As more preparation for a saner rate control algorithm API,
share the supported rates bitmap in the public API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable in sta_info is only used in a meaningful way
by the Intel RC algorithms, so move it into those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In analogy with the previous patch to make mac80211-hwsim
verify that the virtual interface pointers are correct,
this makes it very that it knows about all station structs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211-hwsim is a debugging tool for mac80211, and as such
it can very well verify that mac80211 isn't passing junk to
drivers, especially the vif pointer is prone to this because
for vlan interfaces the AP interface pointer needs to be passed.
This makes mac80211-hwsim add a magic cookie to the private vif
area and verify it whenever an operation is called that gets a
vif pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And support setting both long and short retries independently.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RF kill support is enabled when CONFIG_RFKILL
is set.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the functions in main.c are re-ordered in such
a way that all local functions are defined before mac80211
and pci callbacks.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic reset command is unused. Each interface type needs to
handle the reset command differently since after reset, the firmware is
dead and interface-specific mechanisms must be used to reinitialize the
card.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up zd1211rw's own regulatory work, and makes use of
the new cfg80211 regulatory_hint().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
