Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U8500 UIB contains a Synaptics RMI touchpanel and
a matrix keyboard via the TC35893 port expander device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST-UIB contains a matrix keypad interfaced with the
STMPE1601 port expander and a ROHM BU2101 touch panel.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include ab8500 regulators for DB8500 SoC by default
and fix build issues
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
[Small fixup for changed boardfiles]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Try to make the regulators a little bit more useful by adding some
of the most basic consumers we're going to have in the end.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the PMU resources necessary to get perf working with
the DB5500 ASIC.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates HRT driver for supporting PM.
The resume function of PWM4 timer which is used clocksource is needed
when kernel is resuming for restarting.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support suspend to ram for EXYNOS4210.
As a note, this includes function of outer cache flush
because it is used before entering PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions of PMU and CMU registers for EXYNOS4 PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for fourth FIMC platform device definition and define
resources for FIMC modules on EXYNOS4 machines.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates s5pv210_defconfig and s5p64x0_defconfig for
HRT support and CONFIG_S5P_HRT is used for its configuration.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HRT for machines of S5P64X0 and S5PV210.
Basically, PWM Timer3 is used for clockevent and PWM Timer4 is
used for clocksource. Since PWM Timer3 is used for other purpose,
PWM Timer2 is used on SMDKV210.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HR-Timer(High Resolution Timer) and dynamic
tick system for S5P SoCs. There are many clock sources for HR-Timer
on S5P SoCs. The PWM timer, RTC, System Timer, and MCT can be used
for clock source.
This patch can only support PWM timer for clock source of S5P64X0
and S5PV210.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add macro for defining static pins in the board file.
We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 75e2ea643f (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add spi clock information for da850.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The spi driver name called out for the da830 spi clock list is not correct,
fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Extract magic numbers from DMA resource initializers to #defines.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The DA830_edma_ch enum set is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The patch adds the new power management trace points for
the OMAP architecture.
The trace points are for:
- default idle handler. Since the cpuidle framework is
instrumented in the generic way there is no need to
add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
the actually hit state.
Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.
Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This Patch adds OPP enteries for IVA in OMAP4 OPP Table
Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.
This will avoid opp table and voltage layer having conflicting values.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
prototypes to use u32 types for the futex as this is the data type the
futex core code uses all over the place.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311025058.GD26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cmpxchg_futex_value_locked API was funny in that it returned either
the original, user-exposed futex value OR an error code such as -EFAULT.
This was confusing at best, and could be a source of livelocks in places
that retry the cmpxchg_futex_value_locked after trying to fix the issue
by running fault_in_user_writeable().
This change makes the cmpxchg_futex_value_locked API more similar to the
get_futex_value_locked one, returning an error code and updating the
original value through a reference argument.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile]
Acked-by: Tony Luck <tony.luck@intel.com> [ia64]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <monstr@monstr.eu> [microblaze]
Acked-by: David Howells <dhowells@redhat.com> [frv]
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024851.GC26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kernel/futex.c disables page faults before calling
futex_atomic_cmpxchg_inatomic(), so there is no need to do it again
within that function.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024731.GB26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are two dividers used to derive bus clock from system clock:
system clock is divided by SCKDIV+1, then by BCKDIV+1. SCKDIV divider
has been ignored up to now, which is no problem as long as it is 0.
Take SCKDIV into account for bus clock calculation.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove double definition of ACLKUSBH, change parameter name in
root_clk_disable, as there is no reason to have a different name than
in root_clk_enable.
No functional change.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason why in case of PLL2 the configuration register
should be read twice, while for PLL0/1 using the value previously read
is used. Do the same for PLL2.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The calculation of the best divider value for a requested clock rate
always returned a value that was slightly too large. It was also not
protected against possible divisions by zero.
Request for very low, but non zero rates would cause the ACLK divisor
field to overflow. Catch this situation by using the maximum value.
The internal function aclk_set_rate() calculates the correct divider
value, but doesn't write it back to the register. Add the write back.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If NAND is enabled we better have the include around.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add common code for MIPI-CSIS and MIPI-DSIM drivers to support
their corresponding D-PHY's enable and reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Extend MIPI-CSIS driver's platform data structure with a callback
for D-PHY enable and reset control. Also add a flag indicating
whether the external MIPI-CSI (VDD18_MIPI) power supply should
be managed in the driver through the "vdd" power supply. On some
boards this regulator may be a fixed voltage regulator without
an inhibit function.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add functions for configuration of the parallel camera
bus pins on S5PV210 and Exynos4 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.
This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
This is a first pass at reorganizing mach-omap2/voltage.c:
- Separate almost all of the data from the code of mach-omap2/voltage.c.
The code remains in mach-omap2/voltage.c. The data goes into one
of several places, depending on what type of data it is:
- Silicon process/validation data: mach-omap2/opp*_data.c
- VC (Voltage Controller) data: mach-omap2/vc*_data.c
- VP (Voltage Processor) data: mach-omap2/vp*_data.c
- Voltage domain data: mach-omap2/voltagedomains*_data.c
The ultimate goal is for all this data to be autogenerated, the same
way we autogenerate the rest of our data.
- Separate VC and VP common data from VDD-specific VC and VP data.
- Separate common voltage.c code from SoC-specific code; reuse common code.
- Reorganize structures to avoid unnecessary memory loss due to unpacked
fields.
There is much left to be done. VC code and VP code should be separated out
into vc*.c and vp*.c files. Many fields in the existing structures are
superfluous, and should be removed. Some code in voltage.c seems to be
duplicated; that code should be moved into functions of its own. Proper
voltage domain code should be created, as was done with the powerdomain
and clockdomains, and powerdomains should reference voltagedomains.
Thanks to Shweta Gulati <shweta.gulati@ti.com> for comments. Thanks
to Rajendra Nayak <rnayak@ti.com> for finding and fixing some bugs
that prevented OMAP4 from booting:
https://patchwork.kernel.org/patch/587311/
His patch has been folded into this one to avoid breaking OMAP4
between patches. Thanks also to Kevin Hilman <khilman@ti.com> for
finding and fixing a compile problem when !CONFIG_PM:
http://www.spinics.net/lists/arm-kernel/msg118067.html
His patch has also been folded into this one to avoid breaking
!CONFIG_PM builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shweta Gulati <shweta.gulati@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
The Multi-Core Timer(MCT) of EXYNOS4 is designed for implementing
clock source timer and clock event timers. This patch implements
1 clock source timer with 64 bit free running counter of MCT and
2 clock event timers with two of 31-bit tick counters.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds IRQ_MCT_G0 to irq map. IRQ_MCT_G0 is an interrupt
of MCT comparator and used for kernel global timer.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The MCT(Multi-Core Timer) is used for implementing kernel timers
for EXYNOS4210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.
Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.
Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.
While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When we're interrupted on the secure side, we should just issue
another smc instruction again instead of replaying the arguments
to smc. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Assign the registers used in the inline assembly immediately
before the inline assembly block. This ensures the compiler
doesn't optimize away dead register assignments when it
shouldn't.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Brown <davidb@codeaurora.org>
We don't want the compiler to remove these asm statements or
reorder them in any way. Mark them as volatile to be sure.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various binutils versions can resolve Thumb-2 branches to
locally-defined, preemptible global symbols as short-range "b.n"
branch instructions.
This is a problem, because there's no guarantee the final
destination of the symbol, or any candidate locations for a
trampoline, are within range of the branch. For this reason, the
kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
relocation in modules at all, and it makes little sense to add
support.
The symptom is that the kernel fails with an "unsupported
relocation" error when loading some modules.
Until fixed tools are available, passing
-fno-optimize-sibling-calls to gcc should prevent gcc generating
code which hits this problem, at the cost of a bit of extra runtime
stack usage in some cases.
The problem is described in more detail at:
https://bugs.launchpad.net/binutils-linaro/+bug/725126
Only Thumb-2 kernels are affected.
This patch adds a new CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 config
option which adds -fno-optimize-sibling-calls to CFLAGS_MODULE
when building a Thumb-2 kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding Thumb2 support to the runtime patching of the virt_to_phys and
phys_to_virt opcodes.
Tested both the 8-bit and the 16-bit fixups, using different placements
in memory to exercize all code paths.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The removal of the single-step emulation from ptrace on ARM means that
thread_struct no longer has software breakpoint fields in its debug
member.
This patch fixes the a.out core dump code so that the debug registers
are zeroed rather than trying to copy from non-existent fields.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the correct I/O address definitions for Footbridge
peripherals when the kernel is compiled without MMU
support.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_sr_probe() creates the smartreflex debug directory and its
underlying nvalue debug directory. These directories are removed in
omap_sr_remove().
Basic smartreflex functionality tested on OMAP3630 Zoom3 & OMAP4430 SDP
Signed-off-by: Anand S Sawant <sawant@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Fix an out-of-range ADR when building for ARM.
* Remove deprecated PC-relative stores.
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words.
* Handle non-interworking return from v7_flush_dcache_all.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Remove deprecated PC-relative stores
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For various reasons, Linux now only officially supports being built
with tools which are new enough to understand the SMC instruction.
Replacing the hand-encoded instructions when the mnemonic also
allows for correct assembly in Thumb-2 (otherwise, the result is
random data in the middle of the code).
The Makefile already ensures that this file is built with a high
enough gcc -march= flag (armv7-a).
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Code marked with ENTRY() also needs a matching ENDPROC() directive,
in order to ensure that the type and instruction set of the
symbol are correctly annotated.
ENDPROC() tags the affected symbol as a function symbol, which will
ensure that link-time fixups don't accidentally switch to the
wrong instruction set.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For CONFIG_THUMB2_KERNEL, the existing definition of do_wfi() will
insert invalid code into the instruction stream.
Any assembler which can assemble Thumb-2 is guaranteed to accept
the "wfi" mnemonic, so for the Thumb-2 case, just use the mnemonic.
The ARM case is left as-is.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
IVA device is not present in many OMAP3 variants.
This patch ensures that initialization is tied to
the presence of IVA on the device.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Voltage control on TWL can be done using VMODE/I2C1/I2C_SR.
Since almost all platforms use I2C_SR on omap3, omap3_twl_init by
default expects that OMAP's I2C_SR is plugged in to TWL's I2C
and calls omap3_twl_set_sr_bit. On platforms where I2C_SR is not connected,
the board files are expected to call omap3_twl_set_sr_bit(false) to
ensure that I2C_SR path is not set for voltage control and prevent
the default behavior of omap3_twl_init.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a description field to each idle C-state. This helps to give
better data with PowerTop and one don't have to refer to the code
to link what Cx means from system point of view while analysing
PowerTop data.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the custom restore_control_register() and use the exported
set_cr() instead to set the system control register(SCTRL) value.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP2 and OMAP3 PM code clears clockdomain wakeup and sleep
dependencies. This is unnecessary after commit
6f7f63cc9a ("OMAP clockdomain:
initialize clockdomain registers when the clockdomain layer starts")
which clears these dependencies during clockdomain init.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.
Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.
Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: Kevin Hilman <khilman@ti.com>
kzalloc() may fail, if so return -ENOMEM. Also Walter Harms suggested
to use kasprintf() instead of kzalloc+strcpy+strcat.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMP3630 silicon can enable higher frequencies only depending on the board
characteristics meeting the recommended standards, and has to be selectively
toggled.
Beagle XM uses 3730 variant and the board design allows enabling 800MHz and
1GHz OPPs. However, We need Smart reflex class 1.5 and ABB to enable 1GHz
safely. For the moment, we tweak the default table to allow for 800Mhz OPP
usage.
Reported-by: Koen Kooi <koen@beagleboard.org>
Tested-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap3 and omap4 opp_init should be made non-static to allow
for platform specific opp table tweaking. making these static
conflicts with the definition in pm.h(global) as well.
we include pm.h as well to ensure that there are no such prototype
conflicts with actual implementation in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case in user has a OMAP3630 < ES1.2 the kernel should warn the user
about the ERRATUM, but using pr_warn instead of WARN_ON is already
enough, as there is nothing else the user can do besides changing the
board.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On revisions of the Cortex-A9 prior to r2p0, the Store Buffer does not
have any automatic draining mechanism and therefore a livelock may occur
if an external agent continuously polls a memory location waiting to
observe an update.
This workaround defines cpu_relax() as smp_mb(), preventing correctly
written polling loops from denying visibility of updates to memory.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p* and r3p* versions of the Cortex-A9, a speculative memory
access may cause a page table walk which starts prior to an ASID switch
but completes afterwards. This can populate the micro-TLB with a stale
entry which may be hit with the new ASID.
This workaround places two dsb instructions in the mm switching code so
that no page table walks can cross the ASID switch.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This applies errata fix 753970 for all ux500 platforms. All
current ASICs suffer from this. If the problem is resolved in
later ASICs, the errata selection can be pushed down to other
Kconfig options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect. The error information
gives the detail regarding the target that was attempted
to be accessed and its corresponding address.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod data base.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod change is aligned with Benoit Cousson.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect.The error info provides
the details regarding the master or the target that
generated the error, type of error and the corresponding address.
The stack dump is also provided.
Signed-off-by: sricharan <r.sricharan@ti.com>
[r.sricharan@ti.com: Enhacements, major cleanup and made it functional]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[santosh.shilimkar@ti.com: Driver design changes as per OMAP4 version]
Signed-off-by: Felipe Balbi <balbi@ti.com>
[balbi@ti.com: Initial version of the driver]
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod database.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Now we used standard SZ_* macros instead of self defined *_SIZE macros. This
patch removes all such unused *_SIZE macros for spear3xx & 6xx.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resource size required mostly is 4K for all devices, whereas currently
reserved space is much beyond that. This patch replaces SIZE macro's used at
multiple places with SZ_4K.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of declarations should be: pmx_devs, shirq support, amba_devices,
plat_devices, routines. This patch moves gpio_device below shirq support.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Device name of SD/MMC/SDIO controller in linux is sdhci. To maintain
consistency across all spear code, rename sdio to sdhci.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes inclusion of hardware.h and spear.h consistent over all spear
variants. Now we will include hardware.h, wherever we need to use hardware
macros. spear.h will be automatically included by hardware.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of inclusion of .h files must be: <linux/...>, <asm/...>, <plat/...>,
<mach/...>. This patch corrects this ordering whereever it is not followed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add a dummy clk_set_rate() function. This is required for compilation
of a few drivers.
- Make functions in plat-spear/clock.c more generic over all SPEAr
platforms.
- Add div_factor in struct clk for clks with .recalc = follow_parent
- Change type of register pointers to void __iomem *
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform specific timer initialization code is moved into platform
specific files.
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- compile padmux only for spear3xx
- padmux initialization code rearranged in evaluation board and machine
files.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IOMEM(x) definition, and use it with MISC_BASE for SPEAr platform.
With this there is no need to typecast misc macros to (unsigned int *).
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use straight 64-bit values as 64-bit operations are fairly efficient on ARM.
Comparing the asm output with and without KTIME_SCALAR, using 64-bit math
generates clearly better code.
Comparing kernel/hrtimer.c .text size, it goes from 0x1414 to 0x119c with
this change.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The simply expanded variable may be evaluated before the target file for
the stat command is up to date or even exists. Switching to a recursively
expanded variable move the execution of the stat command to the location
where LDFLAGS_vmlinux is actually used, fixing the dependency issue
introduced by patch #6746/1.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Few architectures combine the GIC with an external interrupt
controller. On such systems it may be necessary to update both
the GIC registers and the external controller's registers to control
IRQ behavior.
This can be addressed in couple of possible methods.
1. Export common GIC routines along with 'struct irq_chip gic_chip'
and allow architectures to have custom function by override.
2. Provide architecture specific function pointer hooks
within GIC library and leave platforms to add the necessary
code as part of these hooks.
First one might be non-intrusive but have few shortcomings like arch
needs to have there own custom gic library. Locks used should be
common since it caters to same IRQs etc. Maintenance point of view
also it leads to multiple file fixes.
The second probably is cleaner and portable. It ensures that all the
common GIC infrastructure is not touched and also provides archs to
address their specific issue.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Populate the l2x0 set_debug function pointer with OMAP secure call
and enable the PL310 Errata 727915
This patch has dependency on the earlier patch
ARM: l2x0: Errata fix for flush by Way operation can cause data
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 implements the Clean & Invalidate by Way L2 cache maintenance
operation (offset 0x7FC). This operation runs in background so that
PL310 can handle normal accesses while it is in progress. Under very
rare circumstances, due to this erratum, write data can be lost when
PL310 treats a cacheable write transaction during a Clean & Invalidate
by Way operation.
Workaround:
Disable Write-Back and Cache Linefill (Debug Control Register)
Clean & Invalidate by Way (0x7FC)
Re-enable Write-Back and Cache Linefill (Debug Control Register)
This patch also removes any OMAP dependency on PL310 Errata's
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i2c_board_info entry supporting AIC23 codec was added into
the i2c2 bus.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3cf32bba8c ("OMAP: McBSP: Convert
McBSP to platform device model") breaks compilation with non-multi-OMAP1
configs:
CC arch/arm/mach-omap1/mcbsp.o
arch/arm/mach-omap1/mcbsp.c: In function 'omap1_mcbsp_init':
arch/arm/mach-omap1/mcbsp.c:384: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:387: error: invalid use of void expression
arch/arm/mach-omap1/mcbsp.c:390: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:393: error: invalid use of void expression
Fix by avoiding NULL dereferences.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated description not to remove unnecessary branch name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow the MSM8960 IOMMU to access its page tables directly
through the L2 cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Don't read from V2Pxx command registers when doing
iova-to-phys operations. These registers are write-only and
reading the value before modifying the VA bits is
unnecessary.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
