e1000_get_stats() just returns dev->stats so we can leave it
out altogether and let dev_get_stats() do the job.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I just found that when we had changed the Rx path to check for length
instead of the DD bit we introduced an issue in ixgbe_dump since we were no
longer clearing the status bits.
To correct this I am updating ixgbe_dump to look for the length bits in the
descriptor since that is what we are using in the Rx path.
Fixes: c3630cc40b ("ixgbe: Use length to determine if descriptor is done")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch increases the headroom allocated when using build_skb on a
system with 4K pages. Specifically the breakdown of headroom versus cache
size is as follows:
L1 Cache Size Headroom
64 192
64, NET_IP_ALIGN == 2 194
128 128
128, NET_IP_ALIGN == 2 130
256 512
256, NET_IP_ALIGN == 2 258
I stopped at supporting only a cache line size of 256 as that was the
largest cache size I could find supported in the kernel.
With this we are guaranteeing at least 128 bytes of headroom to spare in
the frame. This should be enough for us to insert a couple of IPv6 headers
if needed which is likely enough room for anything XDP should need.
I'm leaving the padding for systems with pages larger than 4K unmodified
for now. XDP currently isn't really setup to work on those types of
systems so we can cross that bridge when we get there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We did not have a check in place for MMNGC.MNG_VETO when setting up link
on X550EM_X KR devices which resulted in link loss for the BMC when
loading the driver.
This patch adds a check for ixgbe_check_reset_blocked() in setup_link()
since in that case there is no PHY reset function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the Marvell 1145 PHY define as we have never had a device that
supports it and have no plan to in the future. The existence of this
define has caused confusing on whether or not this PHY was supported
by ixgbe.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid setting adapter->num_vfs early in the init code path when
using the max_vfs module parameter by passing it to ixgbe_enable_sriov()
as a function parameter.
This fixes an issue where if we failed to allocate vfinfo in
__ixgbe_enable_sriov() the driver will crash with NULL pointer in
ixgbe_disable_sriov() when attempting to free the vfinfo struct based
on adapter->num_vfs. Also it cleans up the assignment of adapter->num_vfs
since now it will only be set in __ixgbe_enable_sriov() and cleared in
ixgbe_disable_sriov().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we exit at the end of the block, we can save a level of
indentation by performing an early return, and make the next several
sections of code more legible, with fewer 80 character line breaks.
Also moved allocating vfinfo at the beginning and the notification
for enabling SRIOV at the end of the function when we know that it
will succeed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the code allocating memory for list of MAC addresses that
the VFs can use for MACVLAN into its own function.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add default setting for mac->ops.setup_link on x550em_a MAC types.
This fixes a link issue on KR parts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We forgot to indicate some of the supported speed on the X553
backplane. This patch attempts to correct for that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch add support for X552 XFI backplane interface. The XFI
backplane requires a custom tuned link. HW/FW owns the link config
for XF backplane and SW must not interfere with it.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial patches supporting X553 sgmii forgot some details. This patch
should cover those missing spots.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The KX4 PHY is configured by the NVM. Currently, the driver is overwriting
the config; remove the code associated with KX4 configuration.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
As pr_cont output can be interleaved by other processes,
using pr_cont should be avoided where possible.
Miscellanea:
- Use a temporary pointer to hold the next descriptions and
consolidate the pr_cont uses
- Use the temporary buffer to hold the 8 u32 register values and
emit those in a single go
- Coalesce formats and logging neatening around those changes
- Fix a defective output for the rx ring entry description when
also emitting rx_buffer_info data
This reduces overall object size a tiny bit too.
$ size drivers/net/ethernet/intel/ixgbe/*.o*
text data bss dec hex filename
62167 728 12 62907 f5bb drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.new
62273 728 12 63013 f625 drivers/net/ethernet/intel/ixgbe/ixgbe_main.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is enabled, add checks to ensure creation of number of VF's is
valid based on the traffic classes configured by the device.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to improve the performance of the Rx path.
Specifically by using build_skb we have several distinct advantages.
In the case of small frames we were previously using a copy-break approach.
This means that we were allocating a page fragment to use for skb->head,
and were having to copy the packet into that region. Both of those calls
are now avoided since we just build the skb around the data.
In the case of large frames the gains are much more significant.
Specifically we were having to allocate skb->head, and copy the headers as
before. However in addition we were having to parse the header using
eth_get_headlen which could be quite expensive. All of this is avoided by
building the frame around the data. I have seen gains as high as 30% when
using VXLAN for instance due to just header pulling overhead.
Finally with all this in place it also sets us up to start looking at
enabling XDP. Specifically we now have a path in which the data is in the
page and the frame is built around it. So if we parse it with XDP before
we call build_skb we can take care of any necessary processing there.
Change-ID: Id4bdd618e94473d41f892417e5d8019639e421e3
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds padding to the start of frames to make room for headroom
for us to eventually start using build_skb. Right now we guarantee at
least NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
available. For example on x86 the headroom should be 192 bytes.
On systems that have too large of a cache line size to support storing 1.5K
padding and shared info we default to using 3K buffers and reserve
everything that isn't used for skb_shared_info or the data buffer for
headroom.
Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are situations where adding padding to the front and back of an Rx
buffer will require that we add additional padding. Specifically if
NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would need
to use 2K buffers which leaves us with no room for the padding.
To preemptively address these cases I am adding support for 3K buffers to
the Rx path so that we can provide the additional padding needed in the
event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since an early commit a few flags have no longer
been used. Remove these definitions to reduce code clutter.
Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.
Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.
Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor cleanup so that we are always updating pf->flags when we
make a change to the private flags instead of updating a mix of either
pf->flags and/or pf->hw_disabled_flags.
In addition I went through and cleaned out all the spots where we were
using the X722 define in regards to this flag.
Lastly since we changed the logic I went through and flushed out any
redundancy and cleaned up the handling of the flags in the Tx path.
Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Re-word the error message displayed when adding a filter with an
invalid flow type. Additionally, report a distinct error message when
the IPv4 protocol is at fault.
Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.
This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver is removed or shut down, close any attached clients
(i.e. i40iw). This prevents a panic seen sometimes on forced driver
removal or system shutdown when iWarp is running.
Change-ID: I4f6161e5a73ffbb2fd5883567b007310302bfcb5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, a client (i40iw) may already be present when probe is
called. Check for this, and add a client instance if necessary.
Change-ID: I2009312694b7ad81f1023919e4c6c86181f21689
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver is unloaded, we need to remove the client instance,
otherwise we leak memory.
Change-ID: If1e7882ac1f6ce15d004722fafbe31afbe0adc9a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a capability negotiation between VF and PF using ENCAP/
ENCAP_CSUM offload flags in order for the VF to support outer checksum
and TSO offloads for encapsulated packets. These capabilities were assumed
by default and enabled in current hardware. Going forward, these features
needs to be negotiated with PF before advertising to the stack.
Additionally, strip out the mac.type checks for X722 since outer checksums
are enabled based on the ENCAP_CSUM offload negotiation flag and maintain
consistency between drivers in how the features are configured.
Change-ID: Ie380a6f57eca557a2bb575b66b12fae36d308920
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2017-04-05
This series contains updates to fm10k only.
Phil Turnbull from Oracle fixes an issue where the argument provided to
FM10K_REMOVED macro was not what was expecting.
Jake modifies the driver to replace the bitwise operators and defines with
a BITMAP and enumeration values to avoid race conditions. Also future
proof the driver so that developers do not have to remember to re-size the
bitmaps when adding new values. Fixed the wording of a code comment to
avoid stating that we return a value for a void function.
Ngai-Mint makes sure that when configuring the receive ring, we make sure
the receive queue is disabled. Fixed an issue where interfaces were
resetting because the transmit mailbox FIFO was becoming full since the
host was not ready, so ensure the host is ready before queueing up
mailbox messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Interfaces will reset whenever the TX mailbox FIFO has become full. This
occurs more frequently whenever the IES API application is not running
to process and clear the messages in the FIFO. Thus, this could lead to
situations where the interface would enter an infinite reset loop. That
is: if the interface is trying to synchronize a huge number of unicast
and multicast entries with the IES API application, the TX mailbox FIFO
will become full and the interface resets. Once the interface exits
reset, it'll try to synchronize the unicast and multicast entries again.
Ergo, this creates an infinite loop. Other actions such as multiple
mulitcast mode or up/down transitions will fill the TX mailbox FIFO and
induce the interface to reset. To correct these situations, check if the
interface's "host_ready" flag is enabled before enqueuing any messages
to the TX mailbox FIFO. This check will be conducted by a function call.
Lastly, this issue mainly affects the PF and, thus, the VF is exempt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Write to RXQCTL register to disable the receive queue when configuring
the RX ring.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Re-word the comment to avoid stating that we return a value for this
void function. Additionally, there is no need to mention older kernels,
since this is the upstream kernel.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If some code path executes fm10k_service_event_schedule(), it is
guaranteed that we only queue the service task once, since we use
__FM10K_SERVICE_SCHED flag. Unfortunately this has a side effect that if
a service request occurs while we are currently running the watchdog, it
is possible that we will fail to notice the request and ignore it until
the next time the request occurs.
This can cause problems with pf/vf mailbox communication and other
service event tasks. To avoid this, introduce a FM10K_SERVICE_REQUEST
bit. When we successfully schedule (and set the _SCHED bit) the service
task, we will clear this bit. However, if we are unable to currently
schedule the service event, we just set the new SERVICE_REQUEST bit.
Finally, after the service event completes, we will re-schedule if the
request bit has been set.
This should ensure that we do not miss any service event schedules,
since we will re-schedule it once the currently running task finishes.
This means that for each request, we will always schedule the service
task to run at least once in full after the request came in.
This will avoid timing issues that can occur with the service event
scheduling. We do pay a cost in re-running many tasks, but all the
service event tasks use either flags to avoid duplicate work, or are
tolerant of being run multiple times.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that future programmers do not have to remember to re-size
the bitmaps due to adding new values. Although this is unlikely for this
driver, it may happen and it's best to prevent it from ever being an
issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace bitwise operators and #defines with a BITMAP and enumeration
values. This is similar to how we handle the "state" values as well.
This has two distinct advantages over the old method. First, we ensure
correctness of operations which are currently problematic due to race
conditions. Suppose that two kernel threads are running, such as the
watchdog and an ethtool ioctl, and both modify flags. We'll say that the
watchdog is CPU A, and the ethtool ioctl is CPU B.
CPU A sets FLAG_1, which can be seen as
CPU A read FLAGS
CPU A write FLAGS | FLAG_1
CPU B sets FLAG_2, which can be seen as
CPU B read FLAGS
CPU A write FLAGS | FLAG_2
However, "|=" and "&=" operators are not actually atomic. So this could
be ordered like the following:
CPU A read FLAGS -> variable
CPU B read FLAGS -> variable
CPU A write FLAGS (variable | FLAG_1)
CPU B write FLAGS (variable | FLAG_2)
Notice how the 2nd write from CPU B could actually undo the write from
CPU A because it isn't guaranteed that the |= operation is atomic.
In practice the race windows for most flag writes is incredibly narrow
so it is not easy to isolate issues. However, the more flags we have,
the more likely they will cause problems. Additionally, if such
a problem were to arise, it would be incredibly difficult to track down.
Second, there is an additional advantage beyond code correctness. We can
now automatically size the BITMAP if more flags were added, so that we
do not need to remember that flags is u32 and thus if we added too many
flags we would over-run the variable. This is not a likely occurrence
for fm10k driver, but this patch can serve as an example for other
drivers which have many more flags.
This particular change does have a bit of trouble converting some of the
idioms previously used with the #defines for flags. Specifically, when
converting FM10K_FLAG_RSS_FIELD_IPV[46]_UDP flags. This whole operation
was actually quite problematic, because we actually stored flags
separately. This could more easily show the problem of the above
re-ordering issue.
This is really difficult to test whether atomics make a difference in
practical scenarios, but you can ensure that basic functionality remains
the same. This patch has a lot of code coverage, but most of it is
relatively simple.
While we are modifying these files, update their copyright year.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'.
Fixes: 5cb8db4a4c ("fm10k: Add support for VF")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a delay to Rx queue disables to accommodate HW needs.
v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.
Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode. The legacy Rx mode is what we currently do when performing
Rx. As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.
Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean up the code in preparation for us adding
support for build_skb. Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.
Specifically with this change we split out the code for adding a page to an
exiting skb.
Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions. This allows us
to commonize the bits that handle either freeing or recycling the buffers.
As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer. It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.
Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.
The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer. We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.
Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag hasn't been used since commit 1e1be8f622 ("i40e: ATR policy
change to flush the table to clean stale ATR rules").
Lets simplify things and just remove it.
Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
