IEEE-802.11n spec says the RX highest data rate field does
not specify the highest supported RX data rate if its not set.
Ignore it if not set then. Refer to section 7.3.56.4
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging you want to be lazy and not have to parse
bits yourself so let mac80211 debugfs do the parsing for you.
This is what I get against my WRT610N:
root@tux:~# cat /sys/kernel/debug/ieee80211/phy0/stations/00\:22\:6b\:aa\:bb\:01/ht_capa
ht supported
cap: 0x000e
HT20/HT40
SM Power Save disabled
No RX STBC
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
ampdu factor/density: 2/6
MCS mask: ff ff 00 00 00 00 00 00 00 00
MCS rx highest: 0
MCS tx params: 0
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS set is 16 bits so when debugging ensure the full 16 bits
are represented. Current reading would make you think its only
8 bits.
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hw rate control is used, these parameters have
no meaning because the hardware cannot get at them
right now, so disallow setting them. Also clean up
the function a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean out some cruft that could use an already existing
sta_info struct -- that case cannot happen. Also, there's
a bug there -- if allocation/insertion fails then it is
possible that we are left in a lingering state where
mac80211 waits for the AP, cfg80211 waits for mac80211,
but the AP has already replied. Since there's no way to
indicate an internal error, pretend there was a timeout,
i.e. that the AP never responded.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it is required that a system be
configured with no support for 40 MHz channels in
the 2.4 GHz band. Rather than imposing any such
restrictions on everybody, allow configuration a
system like that with a module parameter. It is
writable at runtime but only takes effect at the
time of the next association.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the A-MSDU handling code from mac80211 to cfg80211 so that more
drivers can use it. The new created function ieee80211_amsdu_to_8023s
converts an A-MSDU frame to a list of 802.3 frames.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 tkip code won't call update_tkip_key, if rx packets
are received without KEY_FLAG_UPLOADED_TO_HARDWARE. This can happen on
first packet because the hardware key stuff is called asynchronously with
todo workqueue.
This patch workaround that by tracking if we sent the key to the driver.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The payload alignment warning enabled by MAC80211_DEBUG_PACKET_ALIGNMENT is
difficult. To fix it, a firmware change is needed but in most cases that's
very difficult. So the benefit from the warning is low and most probably
it just creates more confusion for people who just enable all warnings
(like it did for me).
Remove the unaligned IP payload warning and the kconfig option. But
leave the unaligned packet warning, it will be enabled with
MAC80211_VERBOSE_DEBUG.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not all that useful to have the vif/sdata pointer,
we'd rather refer to the interfaces by their name.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station management currently uses the virtual
interface, but you cannot add the same station to
multiple virtual interfaces if you're communicating
with it in multiple ways.
This restriction should be lifted so that in the
future we can, for instance, support bluetooth 3
with an access point that mac80211 is already
associated to.
We can do that by requiring all sta_info_get users
to provide the virtual interface and making the RX
code aware that an address may match more than one
station struct. Thanks to the previous patches this
one isn't all that large and except for the RX and
TX status paths changes has low complexity.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My
commit 77fdaa12ce
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Jul 7 03:45:17 2009 +0200
mac80211: rework MLME for multiple authentications
inadvertedly broke WMM because it removed, along with
a bunch of other now useless initialisations, the line
initialising sdata->u.mgd.wmm_last_param_set to -1
which would make it adopt any WMM parameter set. If,
as is usually the case, the AP uses WMM parameter set
sequence number zero, we'd never update it until the
AP changes the sequence number.
Add the missing initialisation back to get the WMM
settings from the AP applied locally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.31+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch ("mac80211: Use correct sign for mesh active path
refresh.") was actually a bug. Reverted it and improved the
explanation of how mesh path refresh works.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paths to mesh portals were being timed out immediately after each use in
intermediate forwarding nodes. mppath->exp_time is set to the expiration time
so assigning it to jiffies was marking the path as expired.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Memset should be given the size of the structure, not the size of the pointer.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
expression E;
@@
memset(x, E, sizeof(
+ *
x))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This part was missed in "cfg80211: implement get_wireless_stats",
probably because sta_set_sinfo already existed and was only handling
dBm signals.
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a 32-bit machine, BIT() macro does not give the required
bit value if the bit is mroe than 31. In ieee802_11_parse_elems_crc(),
BIT() is suppossed to get the bit value more than 31 (42 (id of ERP_INFO_IE),
37 (CHANNEL_SWITCH_IE), (42), 32 (POWER_CONSTRAINT_IE), 45 (HT_CAP_IE),
61 (HT_INFO_IE)). As we do not get the required bit value for the above
IEs, crc over these IEs are never calculated, so any dynamic change in these
IEs after the association is not really handled on 32-bit platforms.
This patch fixes this issue.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not only ps_sdata but also IEEE80211_CONF_PS is to be considered
before restoring PS in scan_ps_disable(). For instance, when ps_sdata
is set but CONF_PS is not set just because the dynamic timer is still
running, a sw scan leads to setting of CONF_PS in scan_ps_disable
instead of restarting the dynamic PS timer.
Also for the above case, a null data frame is to be sent after
returning to operating channel which was not happening with the
current implementation. This patch fixes this too.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hwsim testing has revealed that when the MLME
recalculates the idle state of the device, it
sometimes does so before sending the final
deauthentication or disassociation frame. This
patch changes the place where the idle state
is recalculated, but of course driver transmit
is typically asynchronous while configuration
is expected to be synchronous, so it doesn't
fix all possible cases yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "mac80211: correctly place aMPDU RX reorder code"
uses an skb queue for MPDUs that were released from the
buffer. I intentially didn't initialise and use the skb
queue's spinlock, but in this place forgot that the code
variant that doesn't touch the spinlock is needed.
Thanks to Christian Lamparter for quickly spotting the
bug in the backtrace Reinette reported.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Bug-identified-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier optimization on removing unnecessary traffic on cooked
monitor interfaces ("mac80211: reduce the amount of unnecessary traffic
on cooked monitor interfaces ") ended up removing quite a bit more
than just unnecessary traffic. It was not supposed to remove TX status
reporting for injected frames, but ended up doing it by checking the
injected flag in skb->cb only after that field had been cleared with
memset.. Fix this by taking a local copy of the injected flag before
skb->cb is cleared.
This broke user space applications that depend on getting TX status
notifications for injected data frames. For example, STA inactivity
poll from hostapd did not work and ended up kicking out stations even
if they were still present.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
commit d75636ef9c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
and other parts were already present in the original
commit d92684e660
Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
Date: Mon Jan 28 14:07:22 2008 +0200
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek noticed a remotely triggerable problem
in mac80211, which is due to some code shuffling I did
that ended up changing the order in which things were
done -- this was in
commit d75636ef9c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
The problem is that the BUG_ON moved before the various
checks, and as such can be triggered.
As the comment indicates, the BUG_ON can be removed since
the ampdu_action callback must already exist when the
state is OPERATIONAL.
A similar code path leads to a WARN_ON in
ieee80211_stop_tx_ba_session, which can also be removed.
Cc: stable@kernel.org [2.6.29+]
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable logging of more configuration data when tracing
is enabled. Except for the channel frequency this is
only useful with the binary trace format, but that can
be recorded and replayed with trace-cmd and I will be
working on a plugin that reports all the information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated by the comment, the aMPDU RX reorder code
should logically be after ieee80211_rx_h_check(). The
previous patch moved the code there, and this patch now
hooks it up in that place by introducing a list of skbs
that are then processed by the remaining handlers. The
list may be empty if the function is buffering the skb
to release it later.
The only change needed to the RX data is that the crypto
handler needs to clear the key that may be set from a
previous loop iteration, and that not everything can be
in the rx flags now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code should be part of RX handlers, so move it
to the place where it belongs without changing it.
A follow-up patch will do the changes to hook it up.
The sole purpose of this code move is to make the
other patch readable, it doesn't change the code at
all except that it now requires a different static
function declaration (which will go away too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX flags should soon be used only for flags
that cannot change within an a-MPDU, so move the
cooked monitor flag into the RX status flags.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Speedup ieee80211_remove_interfaces() by factorizing synchronize_rcu() calls
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following htmldocs warnings:
Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a missing rcu_read_unlock() before jumping out
of the ieee80211_change_station() function in the
error case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_local.wstats is a remnant from the
days when we still had to worry about wireless
extensions in mac80211 -- it can be removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is sometimes useful to debug HT issues
as it shows what exactly the stack thinks
the peer supports.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With WEXT, it happens frequently that the SME
requests an authentication but then deauthenticates
right away because some new parameters came along.
Every time this happens we print a deauth message
and send a deauth frame, but both of that is rather
confusing. Avoid it by aborting the authentication
process silently, and telling cfg80211 about that.
The patch looks larger than it really is:
__cfg80211_auth_remove() is split out from
cfg80211_send_auth_timeout(), there's no new code
except __cfg80211_auth_canceled() (a one-liner) and
the mac80211 bits (7 new lines of code).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 resumes, it currently first sets suspended
to false so the driver can start doing things and we can
receive frames.
However, if we actually receive frames then it can end
up starting some work which adds timers and then later
runs into a BUG_ON in the timer code because it tries
add_timer() on a pending timer.
Fix this by keeping track of the resuming process by
introducing a new variable 'resuming' which gets set to
true early on instead of setting 'suspended' to false,
and allow queueing work but not receiving frames while
resuming.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's enough code to have its own file, I think.
Especially since I'm going to add to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not assigning the vif pointer causes an oops.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.
It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The netdev broadcast address cannot change from
all-ones so there's no need to use it; we can
instead hard-code it. Since we already have an
instance in tkip.c, which will be shared if it
is marked static const, doing this reduces text
size at no data/bss cost.
The real motivation for this is, of course, the
desire to get rid of almost all uses of netdevs
in mac80211 so that auditing their use becomes
easier.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we move the rcu sections a little, there's
no need to touch the device refcount.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code currently assumes that there's a valid
rate pointer even in the HT case, but there can't
be. To reduce reliance on that, remove the rate
pointer from the RX data struct and pass it where
it's needed.
Also, for now, in radiotap announce HT frames as
having a DYN channel type, and remove their rate
from cooked monitor radiotap completely (it isn't
present in the regular monitor radiotap either.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX data contains the netdev, which is
duplicated since we have the sdata, and the
RX status pointer, which is duplicate since
we have the skb. Remove those two fields to
have fewer fields that depend on each other
and simply load them as necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reorder buffer handling is written in a quite
peculiar style (especially comments) and also has
a quirk where it invokes the entire reorder code
in ieee80211_sta_manage_reorder_buf() for just a
handful of lines in it with a special argument.
Split out ieee80211_release_reorder_frames which
can then be invoked from BAR handling and other
reordering code, clean up code and comments and
remove function arguments that are now unused from
ieee80211_sta_manage_reorder_buf().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a michael MIC failure report from the
hardware we currently do not check whether it is actually
reported on a frame that is destined to us. It shouldn't
be possible to get a michael MIC failure report on other
frames, but it also doesn't hurt to verify.
Also, since we then don't need the station struct that
early, move looking it up a bit later in the RX path.
Finally, while at it, a few code cleanups in the area.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of filtering by device, directly look up by sdata.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle association and authentication in AP mode,
hostapd needs access to the tx status info of its own frames
through a cooked monitor interface. Without this patch the
cooked monitor interfaces also passed on tx status information
for packets from other virtual interfaces. This creates a
significant performance issue on embedded system. Hostapd
tries to work around this by installing a Linux Socket Filter
that only captures the frames it's interested in, however
data duplication and socket filter matching still uses up
enough CPU cycles to be very noticeable on small systems.
This patch ensures that tx status information of non-injected
frames does not make it to cooked monitor interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 2171abc586
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Thu Oct 29 08:34:00 2009 +0100
mac80211: fix addba timer
left a problem in there, even if the timer was
never started it could be deleted and then added.
Linus pointed out that del_timer_sync() isn't
actually needed if we make the timer able to
deal with no longer being needed when it gets
queued _while_ we're in the locked section that
also deletes it. For that the timer function only
needs to check the HT_ADDBA_RECEIVED_MSK bit as
well as the HT_ADDBA_REQUESTED_MSK bit, only if
the former is clear should it do anything.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cooked monitor interfaces cannot currently receive Probe Request
frames when the interface is in station mode. However, we do not
process Probe Request frames internally in the station MLME, so there
is no point in queueing the frame here. Remove Probe Request frames
from the queued frame list to allow cooked monitor interfaces to
receive these frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this patch, broadcast frames from the station behind a
4-addr AP VLAN would be reflected back to the source.
Fix this by checking the 4-addr flag before bridging multicast
frames in the cell.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RANN (Root Annoucement) frame TX. Send an action frame every second
trying to build a path to all nodes on the mesh.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resulting object files have the same MD5 as before.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BSSID is now set to the TA.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This sets the AID field correctly for mesh peer confirm frames.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase hopcount and convert metric to LE before forwarding the RANN
action frame.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PERR IE frame format according to latest draft (3.03).
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process the RANN (Root Annoucement) Frame and try to find the HWMP
root station by sending a PREQ.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max MCS index is 76, fix the higher check to allow through
frames received at MCS 76. This is a non-issue for current drivers
as MCS 76 is only possible with a device supporting 4 spatial
streams.
While at it change the WARN_ON() on invalid HT rates to a WARN()
to provide more useful information. This will help debug issues
when the driver is passing up a bogus HT rate value.
The rate must map to a valid MCS index which can be any of the
values in the set [0 - 76] (inclusive).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it might be useful to run a network with an
Access Point and multiple clients, but with each client bridged
to a network behind it. For this to work, both the client and the
AP need to transmit 4-address frames, containing both source and
destination MAC addresses.
With this patch, you can configure a client to communicate using
only 4-address frames for data traffic.
On the AP side you can enable 4-address frames for individual
clients by isolating them in separate AP VLANs which are configured
in 4-address mode.
Such an AP VLAN will be limited to one client only, and this client
will be used as the destination for all traffic on its interface,
regardless of the destination MAC address in the packet headers.
The advantage of this mode compared to regular WDS mode is that it's
easier to configure and does not require a static list of peer MAC
addresses on any side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print the FSM state strings instead of just the numbers.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the HWMP IEs are now all optional and the action code is fixed,
allow the HWMP code to find and process each IE on the path
selection action frames.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <rpaulo@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add MAC80211_VERBOSE_MHWMP_DEBUG, a debugging option for HWMP
frame processing.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the format of path selection frames according to latest
draft (3.03).
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the length and format of the peer link management action frames.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Mesh Configuration Formation Info field contains the number of
neighbors. This means that the beacon must be updated every time a
peer joins or leaves.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <rpaulo@gmail.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the mesh time to live field to 31 according to draft 3.03.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the Mesh Configuration IE according to the latest
draft (3.03).
Notable changes include the simplified protocol IDs.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices require that all frames to a station
are flushed when that station goes into powersave
mode before being able to send frames to that
station again when it wakes up or polls -- all in
order to avoid reordering and too many or too few
frames being sent to the station when it polls.
Normally, this is the case unless the station
goes to sleep and wakes up very quickly again.
But in that case, frames for it may be pending
on the hardware queues, and thus races could
happen in the case of multiple hardware queues
used for QoS/WMM. Normally this isn't a problem,
but with the iwlwifi mechanism we need to make
sure the race doesn't happen.
This makes mac80211 able to cope with the race
with driver help by a new WLAN_STA_PS_DRIVER
per-station flag that can be controlled by the
driver and tells mac80211 whether it can transmit
frames or not. This flag must be set according to
very specific rules outlined in the documentation
for the function that controls it.
When we buffer new frames for the station, we
normally set the TIM bit right away, but while
the driver has blocked transmission to that sta
we need to avoid that as well since we cannot
respond to the station if it wakes up due to the
TIM bit. Once the driver unblocks, we can set
the TIM bit.
Similarly, when the station just wakes up, we
need to wait until all other frames are flushed
before we can transmit frames to that station,
so the same applies here, we need to wait for
the driver to give the OK.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal scan request mac80211 uses to
scan for IBSS networks was set up to contain
no channels at all because n_channels wasn't
set after setting up the channels array. Fix
this to properly scan for networks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, in IBSS mode, a single creator would go into
a loop trying to merge/scan. This happens because the IBSS timer is
rearmed on finishing a scan and the subsequent
timer invocation requests another scan immediately.
This patch fixes this issue by checking if we have just completed
a scan run trying to merge with other IBSS networks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently it is possible to request a scan on only
disabled channels, which could be problematic for
some drivers. Reject such scans, and also ignore
disabled channels that are given. This resuls in
the scan begin/end event only including channels
that are actually used.
This makes the mac80211 check for disabled channels
superfluous. At the same time, remove the no-IBSS
check from mac80211 -- nothing says that we should
not find any networks on channels that cannot be
used for an IBSS, even when operating in IBSS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since sometimes mac80211 queues up a scan request
to only act on it later, it must be allowed to
(internally) cancel a not-yet-running scan, e.g.
when the interface is taken down. This condition
was missing since we always checked only the
local->scanning variable which isn't yet set in
that situation.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The multi-line code in this macro wasn't wrapped
in do {} while (0) so we cannot use it in an if()
branch safely in the future -- fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some strange reason the netif_running() check
ended up after the actual type change instead of
before, potentially causing all kinds of problems
if the interface is up while changing the type;
one of the problems manifests itself as a warning:
WARNING: at net/mac80211/iface.c:651 ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]()
Hardware name: Aspire one
Pid: 2596, comm: wpa_supplicant Tainted: G W 2.6.31-10-generic #32-Ubuntu
Call Trace:
[] warn_slowpath_common+0x6d/0xa0
[] warn_slowpath_null+0x15/0x20
[] ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]
[] ieee80211_if_change_type+0x4a/0xc0 [mac80211]
[] ieee80211_change_iface+0x61/0xa0 [mac80211]
[] cfg80211_wext_siwmode+0xc7/0x120 [cfg80211]
[] ioctl_standard_call+0x58/0xf0
(http://www.kerneloops.org/searchweek.php?search=ieee80211_teardown_sdata)
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not right to do something here when returning an
error, and hostapd should never have relied on it as
it only fixes up a small part of the problem anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is set once, and tested once.
However, the code path that can set it is
mutually exclusive with the code path that
tests it, so the test is always true. Thus
we also don't need to set it either and can
just remove the variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We drop nullfunc frames, but not qos-nullfunc frames,
even though those could be used for PS state control
as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 is asked to buffer multicast frames
in AP mode, it will not set the flag indicating
that the frames should be sent after the DTIM
beacon for those frames buffered in software. Fix
this little inconsistency by always setting that
flag in the buffering code path.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value is unused by mac80211, because it was only
be used by wireless extensions, and turned out to not
be useful there because the quality value needs to be
comparable between scan results and the current value
which is impossible when the qual value is calculated
taking into account noise, for example.
Since it is unused anyway, this patch deprecates it
in the hope that drivers will remove their sometimes
quite expensive calculations of the value.
I'm open to actual uses of the value, but the best
way of using it seems to be what the Intel drivers do
which should probably be generalised if we have noise
values from the hardware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compared to ieee80211_beacon_get(), the new function
ieee80211_beacon_get_tim() returns information on the
location and length of the TIM IE, which some drivers
need in order to generate the TIM on the device. The
old function, ieee80211_beacon_get(), becomes a small
static inline wrapper around the new one to not break
all drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixed a BUG_ON in __skb_trim() when paged rx is used in
iwlwifi driver. Yes, the whole mac80211 stack doesn't support
paged SKB yet. But let's start the work slowly from small
code snippets.
Reported-and-tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While there may be a case for a driver adding its
own bits of radiotap information, none currently
does. Also, drivers would have to copy the code
to generate the radiotap bits that now mac80211
generates. If some driver in the future needs to
add some driver-specific information I'd expect
that to be in a radiotap vendor namespace and we
can add a different way of passing such data up
and having mac80211 include it.
Additionally, rename IEEE80211_CONF_RADIOTAP to
IEEE80211_CONF_MONITOR since it's still used by
b43(legacy) to obtain per-frame timestamps.
The purpose of this patch is to simplify the RX
code in mac80211 to make it easier to add paged
skb support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In
commit 601ae7f25a
Author: Bruno Randolf <br1@einfach.org>
Date: Thu May 8 19:22:43 2008 +0200
mac80211: make rx radiotap header more flexible
code was added that tried to align the radiotap header
position in memory based on the radiotap header length.
Quite obviously, that is completely useless.
Instead of trying to do that, use unaligned accesses
to generate the radiotap header. To properly do that,
we also need to mark struct ieee80211_radiotap_header
packed, but that is fine since it's already packed
(and it should be marked packed anyway since its a
wire format).
Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's currently a very odd bug in mac80211 -- a
hardware scan that is done while the hardware is
really operating on 2.4 GHz will include CCK rates
in the probe request frame, even on 5 GHz (if the
driver uses the mac80211 IEs). Vice versa, if the
hardware is operating on 5 GHz the 2.4 GHz probe
requests will not include CCK rates even though
they should.
Fix this by splitting up cfg80211 scan requests by
band -- recalculating the IEs every time -- and
requesting only per-band scans from the driver.
Apparently this bug hasn't been a problem yet, but
it is imaginable that some older access points get
confused if confronted with such behaviour.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This comment hasn't been a real TODO item for a long
time now since we fixed that quite a while ago.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In TX path it was assumed that dynamic power save works only if
IEEE80211_HW_PS_NULLFUNC_STACK is set. But is not the case, there are
devices which have nullfunc support in hardware but need mac80211
to handle dynamic power save timers, TI's wl1251 is one of them.
The fix is to not check for IEEE80211_HW_PS_NULLFUNC_STACK in
is_dynamic_ps_enabled(), instead check IEEE80211_HW_SUPPORTS_PS and
IEEE80211_HW_SUPPORTS_DYNAMIC_PS flags and act accordingly.
Tested with wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor dynamic power save checks to a function of it's own for better
readibility. No functional changes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can save a lot of code and pointers in the structs
by using debugfs_remove_recursive().
First, change cfg80211 to use debugfs_remove_recursive()
so that drivers do not need to clean up any files they
added to the per-wiphy debugfs (if and only if they are
ok to be accessed until after wiphy_unregister!).
Then also make mac80211 use debugfs_remove_recursive()
where necessary -- it need not remove per-wiphy files
as cfg80211 now removes those, but netdev etc. files
still need to be handled but can now be removed without
needing struct dentry pointers to all of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When HT debugging is enabled and we receive a DelBA
frame we print out the reason code in the wrong byte
order. Fix that so we don't get weird values printed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addba timer function acquires the sta spinlock,
but at the same time we try to del_timer_sync() it
under the spinlock which can produce deadlocks.
To fix this, always del_timer_sync() the timer in
ieee80211_process_addba_resp() and add it again
after checking the conditions, if necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code leaks a BSS struct after telling
cfg80211 about a given BSS by passing a frame.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
qlge: Fix firmware mailbox command timeout.
qlge: Fix EEH handling.
AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)
bonding: fix a race condition in calls to slave MII ioctls
virtio-net: fix data corruption with OOM
sfc: Set ip_summed correctly for page buffers passed to GRO
cnic: Fix L2CTX_STATUSB_NUM offset in context memory.
MAINTAINERS: rt2x00 list is moderated
airo: Reorder tests, check bounds before element
mac80211: fix for incorrect sequence number on hostapd injected frames
libertas spi: fix sparse errors
mac80211: trivial: fix spelling in mesh_hwmp
cfg80211: sme: deauthenticate on assoc failure
mac80211: keep auth state when assoc fails
mac80211: fix ibss joining
b43: add 'struct b43_wl' missing declaration
b43: Fix Bugzilla #14181 and the bug from the previous 'fix'
rt2x00: Fix crypto in TX frame for rt2800usb
...
This makes the mesh housekeeping timer work properly on big endian
systems.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh portals proxy traffic for nodes external to the mesh. When a
proxied frame is received by a mesh interface, it should update its mesh
portal table. This was only happening for unicast frames. With this
change we also learn about mesh portals from proxied multicast frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace netif_tx_{start,stop,wake}_all_queues with the single-queue
equivalents (i.e. netif_{start,stop,wake}_queue). Since we are down to
a single queue, these should peform slightly better.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of cookies in cfg80211_send_XXX() functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.
A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in the description of hwmp_route_info_get(), no function
changes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When association fails, we should stay authenticated,
which in mac80211 is represented by the existence of
the mlme work struct, so we cannot free that, instead
we need to just set it to idle.
(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commit "mac80211: fix logic error ibss merge bssid check" fixed
joining of ibss cell when static bssid is provided. In this case
ifibss->bssid is set before the cell is joined and comparing that address
to a bss should thus always succeed. Unfortunately this change broke the
other case of joining a ibss cell without providing a static bssid where
the value of ifibss->bssid is not set before the cell is joined.
Since ifibss->bssid may be set before or after joining the cell we do not
learn anything by comparing it to a known bss. Remove this check.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx() must be called with softirqs disabled
since the networking stack requires this for netif_rx()
and some code in mac80211 can assume that it can not
be processing its own tasklet and this call at the same
time.
It may be possible to remove this requirement after a
careful audit of mac80211 and doing any needed locking
improvements in it along with disabling softirqs around
netif_rx(). An alternative might be to push all packet
processing to process context in mac80211, instead of
to the tasklet, and add other synchronisation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan completes, we call ieee80211_sta_find_ibss(),
which is also called from other places. When the scan was
done in software, there's no problem as both run from the
single-threaded mac80211 workqueue and are thus serialised
against each other, but with hardware scan the completion
can be in a different context and race against callers of
this function from the workqueue (e.g. due to beacon RX).
So instead of calling ieee80211_sta_find_ibss() directly,
just arm the timer and have it fire, scheduling the work,
which will invoke ieee80211_sta_find_ibss() (if that is
appropriate in the current state).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
kfree_skb() should be used to free struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following step-by step:
1. A STA authenticates and associates with the AP and exchanges
traffic.
2. The STA reports to the AP that it is going to PS state.
3. Some time later the STA device goes to the stand-by mode (not only
its wi-fi card, but the device itself) and drops the association state
without sending a disassociation frame.
4. The STA device wakes up and begins authentication with an
Auth frame as it hasn't been authenticated/associated previously.
At the step 4 the AP "remembers" the STA and considers it is still in
the PS state, so the AP buffers frames, which it has to send to the STA.
But the STA isn't actually in the PS state and so it neither checks
TIM bits nor reports to the AP that it isn't power saving.
Because of that authentication/[re]association fails.
To fix authentication/[re]association stage of this issue, Auth, Assoc
Resp and Reassoc Resp frames are transmitted disregarding of STA's power
saving state.
N.B. This patch doesn't fix further data frame exchange after
authentication/[re]association. A patch in hostapd is required to fix
that.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's useful to know the MAC address when being
disassociated; fix a typo (missing colon) and
move some messages so we get them only when they
are actually taking effect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the DTIM setting is read from beacons, mac80211 will
assume it is 1 if the TIM IE is not present or the value
is 0. This sounds fine, but the same function processes
probe responses as well, which don't have a TIM IE. This
leads to overwriting any values previously parsed out of
beacon frames.
Thus, instead of checking for the presence of the TIM IE
when setting the default, simply check whether the DTIM
period value is valid already. If the TIM IE is not there
then the value cannot be valid (it is initialised to 0)
and probe responses received after beacons will not lead
to overwriting an already valid value.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The contention window is supposed to be a power of two minus one, i.e.
15, 31, 63, 127... minstrel_rate_init() forgets to subtract 1, so the
sequence becomes 15, 32, 66, 134...
Bug reported by Dan Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can just display this upon enabling mac80211 with an
'if MAC80211 != n' check.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All instances of file_operations should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the queued management work items are processed in
ieee80211_sta_work() an item could be removed. This could change the
anybusy from true to false, so we better check whether we can start a
new scan only after having processed the pending work first.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is taken down while a scan is
pending -- i.e. a scan request was accepted but
not yet acted upon due to other work being in
progress -- we currently do not properly cancel
that scan and end up getting stuck. Fix this by
doing better checks when an interface is taken
down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An integer overflow in the minstrel debug code prevented the
throughput to be displayed correctly. This patch fixes that,
by permutating operations like proposed by Pavel Roskin.
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mac80211's RX path some of the warnings that
warn about drivers passing invalid status values
leak the skb, fix that by refactoring the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that the throughput field of the minstrel_rate struct is never used,
so remove it.
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way the tasklets work in mac80211 there's
no need to ever disable them.
However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).
I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.
Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh config information element has changed significantly since draft 1.08
This patch brings it up to date.
Thanks to Sam Leffler and Rui Paulo for identifying this.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: fix alignment problem in scan request"
introduced a bug into the error path, because now
we allocate the entire scan request and not just
the channel list (the channel list is allocated
together with the scan request) -- on errors we
thus also need to free the entire scan request.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This expands on the current fwded_frames stat counter which should be equal to
the total of these two new counters. The new counters are called "fwded_mcast"
and "fwded_unicast".
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] net/mac80211/rc80211_pid_algo.o
net/mac80211/rc80211_pid_algo.c: In function ‘rate_control_pid_rate_init’:
net/mac80211/rc80211_pid_algo.c:304: warning: unused variable ‘si’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh uses the tx failure average to compute the (m)path metric. This used to
be done inside the rate control module. This patch breaks the dependency
between the mesh stack and the rate control algorithm. Mesh will now work
independently of the chosen rate control algorithm.
The mesh stack keeps a moving average of the average transmission losses for
each mesh peer station. If the fail average exceeds a certain threshold, the
peer link is marked as broken.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames. This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid. This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.
Also, minor fix to coding style on that file.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif. This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx(). This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents calling rcu_synchronize from within the tx path by moving the
table growth code to the mesh workqueue.
Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and
declare them static.
Also, re-enable mesh in Kconfig and update the configuration description.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh stack was enabling beaconing without specifying an interval. This
patch defines a default beaconing interval of 1s.
Incidentally, this fixes mesh beaconing in mac80211_hwsim devices.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change triggers a path discovery as soon as the link quality degrades
below a certain threshold. This results in a faster path recovery time than
by simply relying on the periodic path refresh mechanism to detect broken
links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fail_avg value is used to compute the mesh metric, and was only being set
by the pid rate control module. This fixes the mesh path selection mechanism
for cards that use mistrel for rate control.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On locally originated traffic, we refresh active paths after a timeout. The
decision to do this was using the wrong sign and therefore the refresh timer
was triggered for every frame.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, fix typo in comment.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The memory layout for scan requests was rather wrong,
we put the scan SSIDs before the channels which could
lead to the channel pointers being unaligned in memory.
It turns out that using a pointer to the channel array
isn't necessary anyway since we can embed a zero-length
array into the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have a lot of frames to transmit at once, for
instance with fragmentation, it can be an optimisation
to only tell the DMA engine about them on the last
fragment/frame to avoid banging the IO too much. This
patch allows implementation such an optimisation by
telling the driver when more frames can be expected.
Currently, this is used by mac80211 only on fragmented
frames, but could also be used in the future on other
frames when the queue was full and there are multiple
frames pending.
Note that drivers need to be careful when using this
flag, they need to kick their DMA engines not just
when this flag is clear, but also when the queue gets
full so that progress can be made.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.
This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.
The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After being disassociated by the AP, mac80211 currently
reports this to cfg80211, and then goes to delete the
association. That's fine, but cfg80211 assumes that it's
still authenticated, however, mac80211 throws away all
state.
This fixes mac80211 to keep track of the authentication
in that case so that cfg80211 can request a deauth or
new association properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh is currently disabled on mac80211, its marked
as broken. This patch gets it to compile though,
to account for the mac80211 workqueue changes.
There was a simple typo in the patches for mesh
for the workqueue migration, but we never compile
tested it as we couldn't even select mesh as its
broken. Lets at least let it compile for those
interested in getting it fixed.
Reported-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We splice skbs from the pending queue for a TID
onto the local pending queue when tearing down a
block ack request. This is not necessary unless we
actually have received a request to start a block ack
request (rate control, for example). If we never received
that request we should not be splicing the tid pending
queue as it would be null, causing a panic.
Not sure yet how exactly we allowed through a call when the
tid state does not have at least HT_ADDBA_REQUESTED_MSK set,
that will require some further review as it is not quite
obvious.
For more information see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=13922
This fixes this oops:
BUG: unable to handle kernel NULL pointer dereference at 00000030
IP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
*pdpt = 0000000002d1e001 *pde = 0000000000000000
Thread overran stack, or stack corrupted
Oops: 0000 [#1] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: <bleh>
Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051
EIP: 0060:[<f8806c70>] EFLAGS: 00010292 CPU: 0
EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000
ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000)
Stack: <bleh2>
Call Trace:
[<f8806edb>] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211]
[<f8802f1e>] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211]
[<c04862ff>] ? net_rx_action+0xef/0x1d0
[<c0149378>] ? tasklet_action+0x58/0xc0
[<c014a0f2>] ? __do_softirq+0xc2/0x190
[<c018eb48>] ? handle_IRQ_event+0x58/0x140
[<c01205fe>] ? ack_apic_level+0x7e/0x270
[<c014a1fd>] ? do_softirq+0x3d/0x40
[<c014a345>] ? irq_exit+0x65/0x90
[<c010a6af>] ? do_IRQ+0x4f/0xc0
[<c014a35d>] ? irq_exit+0x7d/0x90
[<c011d547>] ? smp_apic_timer_interrupt+0x57/0x90
[<c01094a9>] ? common_interrupt+0x29/0x30
[<c010fd9e>] ? mwait_idle+0xbe/0x100
[<c0107e42>] ? cpu_idle+0x52/0x90
[<c054b1a5>] ? rest_init+0x55/0x60
[<c077492d>] ? start_kernel+0x315/0x37d
[<c07743ce>] ? unknown_bootoption+0x0/0x1f9
[<c0774099>] ? i386_start_kernel+0x79/0x81
Code: <bleh3>
EIP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38
CR2: 0000000000000030
Cc: stable@kernel.org
Testedy-by: Jack Lau <jackelectronics@hotmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is configured in the AP mode, the mac80211
implementation doesn't inform the driver to receive PS Poll frames.
It leads to inability to communicate with power-saving stations
reliably.
The FIF_CONTROL flag isn't passed by mac80211 to
ieee80211_ops.configure_filter when an interface is in the AP mode.
And it's ok, because we don't want to receive ACK frames and other
control ones, but only PS Poll ones.
This patch introduces the FIF_PSPOLL filter flag in addition to
FIF_CONTROL, which means for the driver "pass PS Poll frames".
This flag is passed to the driver:
A) When an interface is configured in the AP mode.
B) In all cases, when the FIF_CONTROL flag was passed earlier (in
addition to it).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do a probe request every 30 seconds, and wait for probe response,
half a second This should lower the traffic that card sends, thus save
power Wainting longer for response makes probe more robust against
'slow' access points
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retry 5 times (chosen arbitary ), before assuming
that station is out of range.
Fixes frequent disassociations while connected to weak,
and sometimes even strong access points.
Signed-off-by: Maxim Levitky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.
Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the recent MLME rework I did broke powersave
because the ps_sdata isn't assigned at the right time,
and the work item wasn't removed from the list before
calling ieee80211_recalc_ps(). To be more specific,
this broke the case where you'd enabled PS before
associating, either automatically or with iwconfig.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains about a shadowed variable, which
we can just rename, and lots of stuff if the API
tracer is enabled, so kick out the tracer code in
a sparse run -- the macros just confuse it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When downing interfaces, it's a good idea to tell the driver to
stop sending beacons; that way the driver doesn't need special
code in ops->remove_interface() when it should already handle the
case in bss_info_changed().
This fixes a potential crash with at least ath5k since the vif
pointer will be nullified while beacon interrupts are still active.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported a problem that seems to be due to
software retry of already transmitted frames. It turns
out that we've never done that correctly, but due to
some recent changes it now crashes in the TX code. I've
added a comment in the patch that explains the problem
better and also points to possible solutions -- which
I can't implement right now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally! This is what you've all been waiting for!
This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!
RIP wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have handlers IWESSID for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have IWAP handlers for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
