Adding more context from Ville's reply to Rodrigo's question why we
need this:
"The spec says that on some hardware you need to PLL running before you
can poke at the palette registers. I didn't actually try to anger the
hardware so I'm not really sure what would happen otherwise, but IIRC
Jesse said something about a hard system hang..."
And generally documenting such ordering constraints with asserts is
Just Good.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Spruce up the commit message a lot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make assert_sprites_disabled() operational on all platforms where
we currently have sprite support enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ever since gen4 primary planes were fixed to pipes.
And for gen2-3, don't check plane B if it doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable/restore sprite planes around mode-set just like we do for the
primary and cursor planes. Now that we have working sprite clipping,
this actually works quite decently.
Previosuly we didn't even bother to disable sprites when changing mode,
which could lead to a corrupted sprite appearing on the screen after a
modeset (at least on my IVB). Not sure if all hardware generations would
be so forgiving when enabled sprites end up outside the pipe dimensons.
v2: Disable rather than enable sprites in ironlake_crtc_disable()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV doesn't have the old video overlay.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First disable FBC, then IPS, then disable all planes, and finally
disable the pipe.
v2: Mention IPS in the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again follow the same sequence for all generations, because doing
otherwise just doesn't make sense.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the same sequence when enabling the cursor plane during
modeset. No point in doing this stuff in different order on different
generations.
This should also avoid a needless wait for vblank for the g4x cursor
workaround when the cursor gets enabled anyway.
Acked-by: Egbert Eich <eich@suse.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Loading the palette after the planes are enabled can risk showing
incorrect colors. ILK+ already load the palette before even the pipe
is enabled. Just follow the same order for gen2-4 and VLV.
According to BSpec the requirements for palette access are
display core clock and display PLL running. In certain platforms
just the core clock may be enough. But we definitely should have both
running when this gets called during the modeset.
v2: Amend the commit message with some display PLL/core clock info
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can remove some duplicate code. All the PCHs are very similar
and right now the code is the same. I plan to add more code, so we
would have more duplicated code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By stashing a pointer of who opened the device and keeping a list of
open fd, we can then walk each client and inspect how many objects they
have open. For example,
i915_gem_objects:
1102 objects, 613646336 bytes
663 [662] objects, 468783104 [468750336] bytes in gtt
37 [37] active objects, 46874624 [46874624] bytes
626 [625] inactive objects, 421908480 [421875712] bytes
282 unbound objects, 6512640 bytes
85 purgeable objects, 6787072 bytes
28 pinned mappable objects, 3686400 bytes
40 fault mappable objects, 27783168 bytes
2145386496 [536870912] gtt total
Xorg: 43 objects, 32243712 bytes (10223616 active, 16683008 inactive, 4096 unbound)
gnome-shell: 30 objects, 28381184 bytes (0 active, 28336128 inactive, 0 unbound)
xonotic-linux64: 1032 objects, 569933824 bytes (46874624 active, 383545344 inactive, 6508544 unbound)
v2: Use existing drm->filelist as pointed out by Ben.
v3: Not even stashing the task_struct is required as Ben pointed out
drm_file->pid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can simplify the code quite a bit.
Also add a WARN in the sdvo code to complain about a bogus value
and kill the readout code in intel_ddi.c that Jesse sneaked in.
HW state readout for the pixel multiplier will work a bit differently
in the end.
v2: Rebase on top of the fdi pixel mutliplier handling fix.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two exactly same error messages on different error paths makes debugging
difficult. Clarify the messages and distinguish them from each other.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only lvds/tv did actually check for cloning or not, but many more
places should.
Notices because my ivb tried to enable both cpu edp and vga on the
first crtc - the resulting confusion between has_pch_encoder,
has_dp_encoder but not actually being a pch dp encoder resulting in
hilarity (hitting a BUG).
We _really_ need an igt to random-walk our modeset space more
exhaustively.
The bug seems to have been exposed due to a race in the hw load
detection support for VGA: Right after a hotplug VGA was still
detected as connected, but obviously reading the EDID wasn't possible
any more. Hence why restarting X a bit later fixed things. Due to the
1024x756 fallback resolution suddenly more outputs had the same
resolution.
On top of that SNA was confused with the possible_clones mask, trying
to clone outputs which cannot be cloned. That bug is now fixed with
commit fc1e0702b25e647cb423851fb7228989fec28bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed May 29 11:25:28 2013 +0100
sna: fixup up possible_clones kms->X impedance mismatch
v2: Kill intel_encoder_check_is_cloned, spotted by Paulo.
v3: Drop the now unused pipe param.
v4: Kill the stray printk Chris spotted.
v5: Elaborate on how the bug in userspace happened and why it was racy
to reproduce.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP watermark registers don't exist on VLV, so don't touch them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Panel fitters on ivb/hsw are not created equal since not all of them
support the new high-quality upscaling mode. To offset this the hw
allows us to freely assign the pfits to pipes.
Since our code currently doesn't support this we might fall over when
taking over firmware state. So check for this case and WARN about it.
We can then improve the code once we've hit this in the wild. Or once
we decide to support the improved upscale modes, though that requires
global arbitrage of modeset resources across crtcs.
v2: Check for IS_GEN7 instead of IS_IVB || IS_HSW as suggested by
Paulo in his review comment.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can get at this easily through intel_crtc->config now.
v2: Drop more stuff gcc spotted.
v3: Drop even more stuff gcc spotted.
v4: Yet more ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prepares a bit for the next big patch, where we switch the
semantics of the different clocks in the pipe config around.
Since I've broken cpu eDP PLL handling in the first version I've
figured some refactoring is in order.
Split out on request from Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently mutliply the link_bw of the fdi link with the pixel
multiplier, which is wrong: The FDI link doesn't suddenly grow more
bandwidth. In reality the pixel mutliplication only happens in the PCH,
before the pixels are fed into the port.
But since we our code treats the uses the target clock after pixels
are doubled (tripled, ...) already, we need to correct this.
Semantically it's clearer to divide the target clock to get the fdi
dotclock instead of multiplying the bw, so do that instead.
Note that the target clock is already multiplied by the same factor,
so the division will never loose accuracy for the M/N computation.
The lane computation otoh used the wrong value, we also need to feed
the fdi dotclock to that.
Split out on a request from Paulo Zanoni.
v2: Also fix the lane computation, it used the target clock to compute
the bw requirements, not the fdi dotclock (i.e. adjusted with the
pixel multiplier). Since sdvo only uses the pixel multiplier for
low-res modes (with a dotclock below 100MHz) we wouldn't ever have
rejected a bogus mode, but just used an inefficient fdi config.
v3: Amend the commit message to explain better what the change for the
fdi lane config computation is all about. Requested by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I stand by my rule that splitting functions should only do an
exact copy, this is a follow-up patch.
Suggested-by: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the DP madness is cleared out, this is all only per-platform.
So move it out from the intel clock limits structure.
While at it drop the intel prefix on the static functions, call the
vtable entry find_dpll (since it's for the display pll) and rip out
the now unnecessary forward declarations.
Note that the parameters of ->find_dpll are still unchanged, but they
eventually need to be moved over to just take in a pipe configuration.
But currently a lot of things are still missing from the pipe
configuration (reflock, output-specific dpll limits and preferences,
downclocked dotclock). So this will happen in a later step.
Note that intel_g4x_limit has a peculiar case where it selects
intel_limits_i9xx_sdvo as the limit. This is pretty bogus and also not
used since the only output types left are DP and native TV-out which
both use special pre-tuned dpll values.
v2: Re-add comment for the find_pll callback (requested by Paulo) and
elaborate on why the transformation is correct for g4x platforms (to
clarify a review question from Paulo). Double up on that by adding a
WARN as suggested by Paulo Zanoni on irc.
v3: Initialize limits to NULL since gcc is now unhappy.
v4: v2/3 will blow up with a NULL dereference in ->find_dpll for dp and
TV-out ports, spotted by Paulo on irc. So just give up on this madness for
now, and leave this to be fixed in a later patch.
v5: Since the ever-so-slight change for g4x might result in some dpll
parameter computation failing spuriously where before it didn't for
ports with preset dpll settings (DP & TV-out) override this. For
paranoia also do it in the ilk+ code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pineview is just different.
Also split out i9xx_clock from intel_clock and drop the now redundant
struct device * parameter.
Note that in this patch I kill an XXX comment about 100MHz clocks. I
couldn't figure out what this is about, and we don't seem to have any
bug reports about this either. I suspect that it's a remnant from when
the i9xx and ilk+ modeset code was all in the same file since ilk+
does indeed have a 100MHz clock. So I've just killed it to stop the
cargo-culting.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since this is run in the compute config stage we need to check
the new_ pointers, i.e the stage output routing, not the current
modeset layout. Also there was a little logic bug in properly skipping
connectors: The old code did not skip any unused connectors and so
clamped to whatever was left in there (usually 0 if that connector
hasn't seen a EDID 1.4 screen ever since boot-up).
This has been broken when moving the pipe bpp selection in
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
To avoid too much casting switch from drm_ to intel_ types.
Also add a bit of debug output to help reconstructing what's going
on.
v2: Try to clarify this a bit:
- s/pipe_config_set_bpp/compute_baseline_pipe_bpp/ to make it clearer
at which stage this function is run. Also add a comment about what
it does.
- Extract the sink clamping into it's own function.
v3: Actually make it compile.
v4: Split out all the prep refactoring to make the bugfix stick out
really badly. Also elaborate a bit in the commit message about the
nature of the bugfix.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a prep work to fix it up:
- Use intel_connector instead of drm_connector to avoid too much
upcasting in the bugfix patch.
- Extract the connector bpp clamping from the loop-over-connectors
logic.
- Bikeshed function names (to make it clearer that
acompute_baseline_pipe_bpp runs in the compute stage of the modeset
sequence) and add a comment to make it clearer what it does.
No functional change in this patch.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to do them if the pipe is actually running and if the
framebuffers have changed. Removes two "wait for vblank timed out"
messages when doing a suspend/resume cycle on my i855gm.
v2: s/to_intel_ctrc(crtc)/intel_crtc/ spotted by Chris.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
People don't like typedefs these days. Eliminate their use from intel_fb.c.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use container_of() instead of a cast to get struct intel_fbdev
from struct drm_fb_helper.
Also populate the fb_info->par correctly with the drm_fb_helper pointer
instead of the intel_fbdev pointer.
There's no actual functional change since the drm_fb_helper happens to
be the first member inside intel_fbdev.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rework of per ring hangcheck made this obsolete.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Keep track of ring seqno progress and if there are no
progress detected, declare hang. Use actual head (acthd)
to distinguish between ring stuck and batchbuffer looping
situation. Stuck ring will be kicked to trigger progress.
This commit adds a hard limit for batchbuffer completion time.
If batchbuffer completion time is more than 4.5 seconds,
the gpu will be declared hung.
Review comment from Ben which nicely clarifies the semantic change:
"Maybe I'm just stating the functional changes of the patch, but in case
they were unintended here is what I see as potential issues:
1. "If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low.
2. "There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped"
v2: use atchd to detect stuck ring from loop (Ben Widawsky)
v3: Use acthd to check when ring needs kicking.
Declare hang on third time in order to give time for
kick_ring to take effect.
v4: Update commit msg
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Paste in Ben's review comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it will be used for the global bound/unbound list with full PPGTT,
this helps clarify things for upcoming code rework.
Recommended-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we properly keep track of the pages_pin_count, then when we later add
multiple address spaces, the put_pages doesn't need any special checks
to be able to perform it's job.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased on top of the fix for stolen memory pinning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The way the stolen handling works is we take a pin on the backing pages,
but we never actually get a reference to the bo. On freeing objects
allocated with stolen memory, the final unref will end up freeing the
object with pinned pages count left. To enable an assertion to catch
bugs in this code path, this patch cleans up that remaining pin.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not terribly interesting to know that a parameter doesn't exist,
and it can get in the way of interesting messages, especially with the
staggered VECS merging as we've done.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It just prints whether it's supported/enabled/disabled. Feature
requested by the power management team.
v2: Checkpatch started complaining about seq_printf with 1 argument.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IPS is still enabled by default. Feature requested by the power
management team.
This should also help testing the feature on some early pre-production
hardware where there were relationship problems between IPS and PSR.
v2: Rebase on top of the newest IPS implementation.
v3: Check i915_enable_ips at compute_config, not supports_ips, so the
kernel parameter will be ignored at haswell_get_pipe_config.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we track the cpu transcoder we need accurately in the pipe
config we can finally fix up the transcoder check. With the current
code eDP on port D will be broken since we'd errornously cut the
power.
For reference see
commit 2124b72e62
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 22 14:07:23 2013 -0300
drm/i915: don't disable the power well yet
v2:
- Kill the now outdated comment (Paulo)
- Add the missing crtc->base.enabled check and consolidate it (Paulo)
- Smash all checks together, looks neater that way.
v3: Kill the unused encoder variable.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will let userland only try to use the new ring
when the appropriate kernel is present
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A user can run batchbuffer via VEBOX ring.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Removed rebase relic VECS ring from i915_gem_request_info (Damien)
v3: s/hsw/hws in debugfs which I introduced in v2 (Jon)
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
[Order changed, and modified by]
CC: "Bloomfield, Jon" <jon.bloomfield@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the correct lock to protect PM interrupt regs, this was
accidentally lost from earlier (Haihao)
Fix return types (Ben)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's overkill on older gens, but it's useful for newer gens.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment, these values are wiped out anyway by the rps
enable/disable. That will be changed in the next patch though.
v2: Add post install setup to address issue found by Damien in the next
patch.
replaced
WARN_ON(dev_priv->rps.pm_iir != 0);
with rps.pm_iir = 0;
With the v2 of this patch and the deferred pm enabling (which changed
since the original patches) we're now able to get PM interrupts before
we've brought up enabled rps. At this point in boot, we don't want to do
anything about it, so we simply ignore it. Since writing the original
assertion, the code has changed quite a bit, and I believe removing this
assertion is perfectly safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: I don't agree with the justification to drop the WARN and
added a FIXME to that effect.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
