Replace EXTRA_CFLAGS with ccflags-y and EXTRA_AFLAGS with asflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware. This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pin 0 of the EPORT is not connected on the 523x, 5271, 5275 and 528x and the
TIMER on the 523x has 8 pins, not 4.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
With the common intc-2 interrupt controller code in place the ColdFire
527x family startup code can be greatly simplified. Remove all the
interrupt masking code, and the per-device interrupt config here.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This processor only have one FEC and its MDIO pins are
located at a different offset than the code used for
the current CONFIG_M527x.
Tesed on M5271EVB eval platform.
Without this patch the FEC driver will report no PHY attached
if the bootloader does not pre-initialize the PAR_FECI2C GPIO register.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
m68knommu: add FEC platform support to ColdFire CPU's setup code
Move the per-CPU FEC driver setup code into the actual platform
setup code for each ColdFire CPU varient.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the extra asm flags for debugger capabilities, use asflags instead for
EXTRA_AFLAGS. Suggestion from Sam Ravnborg.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 527x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.
Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In most cases when AFALGS is manipuled direct this is a bug
and EXTRA_AFLAGS should have been used.
Fix the obvious candidates.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
