Currently, DSA programs VLANs on shared (DSA and CPU) ports each time it
does so on user ports. This is good for basic functionality but has
several limitations:
- the VLAN group which must reach the CPU may be radically different
from the VLAN group that must be autonomously forwarded by the switch.
In other words, the admin may want to isolate noisy stations and avoid
traffic from them going to the control processor of the switch, where
it would just waste useless cycles. The bridge already supports
independent control of VLAN groups on bridge ports and on the bridge
itself, and when VLAN-aware, it will drop packets in software anyway
if their VID isn't added as a 'self' entry towards the bridge device.
- Replaying host FDB entries may depend, for some drivers like mv88e6xxx,
on replaying the host VLANs as well. The 2 VLAN groups are
approximately the same in most regular cases, but there are corner
cases when timing matters, and DSA's approximation of replicating
VLANs on shared ports simply does not work.
- If a user makes the bridge (implicitly the CPU port) join a VLAN by
accident, there is no way for the CPU port to isolate itself from that
noisy VLAN except by rebooting the system. This is because for each
VLAN added on a user port, DSA will add it on shared ports too, but
for each VLAN deletion on a user port, it will remain installed on
shared ports, since DSA has no good indication of whether the VLAN is
still in use or not.
Now that the bridge driver emits well-balanced SWITCHDEV_OBJ_ID_PORT_VLAN
addition and removal events, DSA has a simple and straightforward task
of separating the bridge port VLANs (these have an orig_dev which is a
DSA slave interface, or a LAG interface) from the host VLANs (these have
an orig_dev which is a bridge interface), and to keep a simple reference
count of each VID on each shared port.
Forwarding VLANs must be installed on the bridge ports and on all DSA
ports interconnecting them. We don't have a good view of the exact
topology, so we simply install forwarding VLANs on all DSA ports, which
is what has been done until now.
Host VLANs must be installed primarily on the dedicated CPU port of each
bridge port. More subtly, they must also be installed on upstream-facing
and downstream-facing DSA ports that are connecting the bridge ports and
the CPU. This ensures that the mv88e6xxx's problem (VID of host FDB
entry may be absent from VTU) is still addressed even if that switch is
in a cross-chip setup, and it has no local CPU port.
Therefore:
- user ports contain only bridge port (forwarding) VLANs, and no
refcounting is necessary
- DSA ports contain both forwarding and host VLANs. Refcounting is
necessary among these 2 types.
- CPU ports contain only host VLANs. Refcounting is also necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_handle_port_obj_add() helper is good for replicating a
port object on the lower interfaces of @dev, if that object was emitted
on a bridge, or on a bridge port that is a LAG.
However, drivers that use this helper limit themselves to a box from
which they can no longer intercept port objects notified on neighbor
ports ("foreign interfaces").
One such driver is DSA, where software bridging with foreign interfaces
such as standalone NICs or Wi-Fi APs is an important use case. There, a
VLAN installed on a neighbor bridge port roughly corresponds to a
forwarding VLAN installed on the DSA switch's CPU port.
To support this use case while also making use of the benefits of the
switchdev_handle_* replication helper for port objects, introduce a new
variant of these functions that crawls through the neighbor ports of
@dev, in search of potentially compatible switchdev ports that are
interested in the event.
The strategy is identical to switchdev_handle_fdb_event_to_device():
if @dev wasn't a switchdev interface, then go one step upper, and
recursively call this function on the bridge that this port belongs to.
At the next recursion step, __switchdev_handle_port_obj_add() will
iterate through the bridge's lower interfaces. Among those, some will be
switchdev interfaces, and one will be the original @dev that we came
from. To prevent infinite recursion, we must suppress reentry into the
original @dev, and just call the @add_cb for the switchdev_interfaces.
It looks like this:
br0
/ | \
/ | \
/ | \
swp0 swp1 eth0
1. __switchdev_handle_port_obj_add(eth0)
-> check_cb(eth0) returns false
-> eth0 has no lower interfaces
-> eth0's bridge is br0
-> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb))
finds br0
2. __switchdev_handle_port_obj_add(br0)
-> check_cb(br0) returns false
-> netdev_for_each_lower_dev
-> check_cb(swp0) returns true, so we don't skip this interface
3. __switchdev_handle_port_obj_add(swp0)
-> check_cb(swp0) returns true, so we call add_cb(swp0)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(swp1) returns true, so we don't skip this interface
4. __switchdev_handle_port_obj_add(swp1)
-> check_cb(swp1) returns true, so we call add_cb(swp1)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(eth0) returns false, so we skip this interface to
avoid infinite recursion
Note: eth0 could have been a LAG, and we don't want to suppress the
recursion through its lowers if those exist, so when check_cb() returns
false, we still call switchdev_lower_dev_find() to estimate whether
there's anything worth a recursion beneath that LAG. Using check_cb()
and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures
out whether the lowers of the LAG are switchdev, but also whether they
actively offload the LAG or not (whether the LAG is "foreign" to the
switchdev interface or not).
The port_obj_info->orig_dev is preserved across recursive calls, so
switchdev drivers still know on which device was this notification
originally emitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_lower_dev_find() assumes RCU read-side critical section
calling context, since it uses netdev_walk_all_lower_dev_rcu().
Rename it appropriately, in preparation of adding a similar iterator
that assumes writer-side rtnl_mutex protection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major user of replayed switchdev objects is DSA, and so far it
hasn't needed information about anything other than bridge port VLANs,
so this is all that br_switchdev_vlan_replay() knows to handle.
DSA has managed to get by through replicating every VLAN addition on a
user port such that the same VLAN is also added on all DSA and CPU
ports, but there is a corner case where this does not work.
The mv88e6xxx DSA driver currently prints this error message as soon as
the first port of a switch joins a bridge:
mv88e6085 0x0000000008b96000:00: port 0 failed to add a6:ef:77:c8:5f:3d vid 1 to fdb: -95
where a6:ef:77:c8:5f:3d vid 1 is a local FDB entry corresponding to the
bridge MAC address in the default_pvid.
The -EOPNOTSUPP is returned by mv88e6xxx_port_db_load_purge() because it
tries to map VID 1 to a FID (the ATU is indexed by FID not VID), but
fails to do so. This is because ->port_fdb_add() is called before
->port_vlan_add() for VID 1.
The abridged timeline of the calls is:
br_add_if
-> netdev_master_upper_dev_link
-> dsa_port_bridge_join
-> switchdev_bridge_port_offload
-> br_switchdev_vlan_replay (*)
-> br_switchdev_fdb_replay
-> mv88e6xxx_port_fdb_add
-> nbp_vlan_init
-> nbp_vlan_add
-> mv88e6xxx_port_vlan_add
and the issue is that at the time of (*), the bridge port isn't in VID 1
(nbp_vlan_init hasn't been called), therefore br_switchdev_vlan_replay()
won't have anything to replay, therefore VID 1 won't be in the VTU by
the time mv88e6xxx_port_fdb_add() is called.
This happens only when the first port of a switch joins. For further
ports, the initial mv88e6xxx_port_vlan_add() is sufficient for VID 1 to
be loaded in the VTU (which is switch-wide, not per port).
The problem is somewhat unique to mv88e6xxx by chance, because most
other drivers offload an FDB entry by VID, so FDBs and VLANs can be
added asynchronously with respect to each other, but addressing the
issue at the bridge layer makes sense, since what mv88e6xxx requires
isn't absurd.
To fix this problem, we need to recognize that it isn't the VLAN group
of the port that we're interested in, but the VLAN group of the bridge
itself (so it isn't a timing issue, but rather insufficient information
being passed from switchdev to drivers).
As mentioned, currently nbp_switchdev_sync_objs() only calls
br_switchdev_vlan_replay() for VLANs corresponding to the port, but the
VLANs corresponding to the bridge itself, for local termination, also
need to be replayed. In this case, VID 1 is not (yet) present in the
port's VLAN group but is present in the bridge's VLAN group.
So to fix this bug, DSA is now obligated to explicitly handle VLANs
pointing towards the bridge in order to "close this race" (which isn't
really a race). As Tobias Waldekranz notices, this also implies that it
must explicitly handle port VLANs on foreign interfaces, something that
worked implicitly before:
https://patchwork.kernel.org/project/netdevbpf/patch/20220209213044.2353153-6-vladimir.oltean@nxp.com/#24735260
So in the end, br_switchdev_vlan_replay() must replay all VLANs from all
VLAN groups: all the ports, and the bridge itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be switchdev drivers that can add/remove a FDB or MDB entry
only as long as the VLAN it's in has been notified and offloaded first.
The nbp_switchdev_sync_objs() method satisfies this requirement on
addition, but nbp_switchdev_unsync_objs() first deletes VLANs, then
deletes MDBs and FDBs. Reverse the order of the function calls to cater
to this requirement.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a VLAN entry is added multiple times in a row to a
bridge port, nbp_vlan_add() calls br_switchdev_port_vlan_add() each
time, even if the VLAN already exists and nothing about it has changed:
bridge vlan add dev lan12 vid 100 master static
Similarly, when a VLAN is added multiple times in a row to a bridge,
br_vlan_add_existing() doesn't filter at all the calls to
br_switchdev_port_vlan_add():
bridge vlan add dev br0 vid 100 self
This behavior makes driver-level accounting of VLANs impossible, since
it is enough for a single deletion event to remove a VLAN, but the
addition event can be emitted an unlimited number of times.
The cause for this can be identified as follows: we rely on
__vlan_add_flags() to retroactively tell us whether it has changed
anything about the VLAN flags or VLAN group pvid. So we'd first have to
call __vlan_add_flags() before calling br_switchdev_port_vlan_add(), in
order to have access to the "bool *changed" information. But we don't
want to change the event ordering, because we'd have to revert the
struct net_bridge_vlan changes we've made if switchdev returns an error.
So to solve this, we need another function that tells us whether any
change is going to occur in the VLAN or VLAN group, _prior_ to calling
__vlan_add_flags().
Split __vlan_add_flags() into a precommit and a commit stage, and rename
it to __vlan_flags_update(). The precommit stage,
__vlan_flags_would_change(), will determine whether there is any reason
to notify switchdev due to a change of flags (note: the BRENTRY flag
transition from false to true is treated separately: as a new switchdev
entry, because we skipped notifying the master VLAN when it wasn't a
brentry yet, and therefore not as a change of flags).
With this lookahead/precommit function in place, we can avoid notifying
switchdev if nothing changed for the VLAN and VLAN group.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a very subtle aspect to the behavior of
__vlan_add_flags(): it changes the struct net_bridge_vlan flags and
pvid, yet it returns true ("changed") even if none of those changed,
just a transition of br_vlan_is_brentry(v) took place from false to
true.
This can be seen in br_vlan_add_existing(), however we do not actually
rely on this subtle behavior, since the "if" condition that checks that
the vlan wasn't a brentry before had a useless (until now) assignment:
*changed = true;
Make things more obvious by actually making __vlan_add_flags() do what's
written on the box, and be more specific about what is actually written
on the box. This is needed because further transformations will be done
to __vlan_add_flags().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port and it doesn't exist on the bridge
device yet, it gets created for the multicast context, but it is
'hidden', since it doesn't have the BRENTRY flag yet:
ip link add br0 type bridge && ip link set swp0 master br0
bridge vlan add dev swp0 vid 100 # the master VLAN 100 gets created
bridge vlan add dev br0 vid 100 self # that VLAN becomes brentry just now
All switchdev drivers ignore switchdev notifiers for VLAN entries which
have the BRENTRY unset, and for good reason: these are merely private
data structures used by the bridge driver. So we might just as well not
notify those at all.
Cleanup in the switchdev drivers that check for the BRENTRY flag is now
possible, and will be handled separately, since those checks just became
dead code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port, a master VLAN gets created on the
bridge for context, but it doesn't have the BRENTRY flag.
Then, when the same VLAN is added to the bridge itself, that enters
through the br_vlan_add_existing() code path and gains the BRENTRY flag,
thus it becomes "existing".
It seems natural to check for this condition early, because the current
code flow is to notify switchdev of the addition of a VLAN that isn't a
brentry, just to delete it immediately afterwards.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the following call path returns an error from switchdev:
nbp_vlan_flush
-> __vlan_del
-> __vlan_vid_del
-> br_switchdev_port_vlan_del
-> __vlan_group_free
-> WARN_ON(!list_empty(&vg->vlan_list));
then the deletion of the net_bridge_vlan is silently halted, which will
trigger the WARN_ON from __vlan_group_free().
The WARN_ON is rather unhelpful, because nothing about the source of the
error is printed. Add a print to catch errors from __vlan_del.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever rt6_uncached_list_flush_dev() swaps rt->rt6_idev
to the blackhole device, parts of IPv6 stack might still need
to increment one SNMP counter.
Root cause, patch from Ido, changelog from Eric :)
This bug suggests that we need to audit rt->rt6_idev usages
and make sure they are properly using RCU protection.
Fixes: e5f80fcf86 ("ipv6: give an IPv6 dev to blackhole_netdev")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts and in the RPS case locking input_pkt_queue is
split into local_irq_disable() and optional spin_lock().
This breaks on PREEMPT_RT because the spinlock_t typed lock can not be
acquired with disabled interrupts.
The sections in which the lock is acquired is usually short in a sense that it
is not causing long und unbounded latiencies. One exception is the
skb_flow_limit() invocation which may invoke a BPF program (and may
require sleeping locks).
By moving local_irq_disable() + spin_lock() into rps_lock(), we can keep
interrupts disabled on !PREEMPT_RT and enabled on PREEMPT_RT kernels.
Without RPS on a PREEMPT_RT kernel, the needed synchronisation happens
as part of local_bh_disable() on the local CPU.
____napi_schedule() is only invoked if sd is from the local CPU. Replace
it with __napi_schedule_irqoff() which already disables interrupts on
PREEMPT_RT as needed. Move this call to rps_ipi_queued() and rename the
function to napi_schedule_rps as suggested by Jakub.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave suggested a while ago (eleven years by now) "Let's make netif_rx()
work in all contexts and get rid of netif_rx_ni()". Eric agreed and
pointed out that modern devices should use netif_receive_skb() to avoid
the overhead.
In the meantime someone added another variant, netif_rx_any_context(),
which behaves as suggested.
netif_rx() must be invoked with disabled bottom halves to ensure that
pending softirqs, which were raised within the function, are handled.
netif_rx_ni() can be invoked only from process context (bottom halves
must be enabled) because the function handles pending softirqs without
checking if bottom halves were disabled or not.
netif_rx_any_context() invokes on the former functions by checking
in_interrupts().
netif_rx() could be taught to handle both cases (disabled and enabled
bottom halves) by simply disabling bottom halves while invoking
netif_rx_internal(). The local_bh_enable() invocation will then invoke
pending softirqs only if the BH-disable counter drops to zero.
Eric is concerned about the overhead of BH-disable+enable especially in
regard to the loopback driver. As critical as this driver is, it will
receive a shortcut to avoid the additional overhead which is not needed.
Add a local_bh_disable() section in netif_rx() to ensure softirqs are
handled if needed.
Provide __netif_rx() which does not disable BH and has a lockdep assert
to ensure that interrupts are disabled. Use this shortcut in the
loopback driver and in drivers/net/*.c.
Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they
can be removed once they are no more users left.
Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preempt_disable() () section was introduced in commit
cece1945bf ("net: disable preemption before call smp_processor_id()")
and adds it in case this function is invoked from preemtible context and
because get_cpu() later on as been added.
The get_cpu() usage was added in commit
b0e28f1eff ("net: netif_rx() must disable preemption")
because ip_dev_loopback_xmit() invoked netif_rx() with enabled preemption
causing a warning in smp_processor_id(). The function netif_rx() should
only be invoked from an interrupt context which implies disabled
preemption. The commit
e30b38c298 ("ip: Fix ip_dev_loopback_xmit()")
was addressing this and replaced netif_rx() with in netif_rx_ni() in
ip_dev_loopback_xmit().
Based on the discussion on the list, the former patch (b0e28f1eff)
should not have been applied only the latter (e30b38c298).
Remove get_cpu() and preempt_disable() since the function is supposed to
be invoked from context with stable per-CPU pointers. Bottom halves have
to be disabled at this point because the function may raise softirqs
which need to be processed.
Link: https://lkml.kernel.org/r/20100415.013347.98375530.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reasons to __udp6_lib_rcv for skb drops. The only twist is that the
NO_SOCKET takes precedence over the CSUM or other counters for that
path (motivation behind this patch - csum counter was misleading).
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduces a lock-free version of smc_tx_work() to
solve unnecessary lock contention, which is expected to be held lock.
So this adds comment to remind people to keep an eye out for locks.
Suggested-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate RTM_NEWROUTE netlink notification when the route preference
changes on an existing kernel generated default route in response to
RA messages. Currently netlink notifications are generated only when
this route is added or deleted but not when the route preference
changes, which can cause userspace routing application state to go
out of sync with kernel.
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in current Linux, MTU policing does not take into account that packets at
the TC ingress have the L2 header pulled. Thus, the same TC police action
(with the same value of tcfp_mtu) behaves differently for ingress/egress.
In addition, the full GSO size is compared to tcfp_mtu: as a consequence,
the policer drops GSO packets even when individual segments have the L2 +
L3 + L4 + payload length below the configured valued of tcfp_mtu.
Improve the accuracy of MTU policing as follows:
- account for mac_len for non-GSO packets at TC ingress.
- compare MTU threshold with the segmented size for GSO packets.
Also, add a kselftest that verifies the correct behavior.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLrkRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZsgWAf/aQb18PB2Wh+tH4qxkNW6jK3zfYSRDbDQ
QvrHcnN4BINorTLcGDvWqw3VANiETCW6mVBG8BWo1NyAlvkNziKaAFI3xVhuOE38
6d+wRVElG9JHeb6OwWCX2vWJmqWVxmEIAkTQrqT9VSSUjGDpS1mc3dAssABeEZhn
yzSKJomSRaRv/aC2f/4eYPAyeMUIZbN3VWFOvElGPls0mdrSBmt9OhAKkf3A3E0M
PuJzhnHgoKhpZ/Gmn+IrDZGC/RkUOfT2zZ5gUK0GVvpTFg2/80ilC7RJk2iF5Ibs
xGuRN9WSo9xWILF3SyRgrrx3ocZG0H2dvkJj4ZQbR485U8iXa+HC1g==
=AUlw
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt_flush_dev() changes one rtable dst.dev
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt_del_uncached_list().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt6_uncached_list_flush_dev() changes one rt6_info
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt6_uncached_list_del().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 addrconf notifiers wants the loopback device to
be the last device being dismantled at netns deletion.
This caused many limitations and work arounds.
Back in linux-5.3, Mahesh added a per host blackhole_netdev
that can be used whenever we need to make sure objects no longer
refer to a disappearing device.
If we attach to blackhole_netdev an ip6_ptr (allocate an idev),
then we can use this special device (which is never freed)
in place of the loopback_dev (which can be freed).
This will permit improvements in netdev_run_todo() and other parts
of the stack where had steps to make sure loopback_dev was
the last device to disappear.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->rtm_tos option is normally used to route packets based on both
the destination address and the DS field. However it's ignored for
IPv6 routes. Setting ->rtm_tos for IPv6 is thus invalid as the route
is going to work only on the destination address anyway, so it won't
behave as specified.
Suggested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA slave interfaces to have their own lockdep
class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA masters to have their own lockdep class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no legacy ports, DSA registers a devlink instance with ports
unconditionally for all switch drivers. Therefore, delete the old-style
ndo operations used for determining bridge forwarding domains.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can control SMC handshake limitation through socket options,
which means that applications who need it must modify their code. It's
quite troublesome for many existing applications. This patch modifies
the global default value of SMC handshake limitation through netlink,
providing a way to put constraint on handshake without modifies any code
for applications.
Suggested-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to add dynamic control for SMC handshake limitation for
every smc sockets, in production environment, it is possible for the
same applications to handle different service types, and may have
different opinion on SMC handshake limitation.
This patch try socket options to complete it, since we don't have socket
option level for SMC yet, which requires us to implement it at the same
time.
This patch does the following:
- add new socket option level: SOL_SMC.
- add new SMC socket option: SMC_LIMIT_HS.
- provide getter/setter for SMC socket options.
Link: https://lore.kernel.org/all/20f504f961e1a803f85d64229ad84260434203bd.1644323503.git.alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intends to provide a mechanism to put constraint on SMC
connections visit according to the pressure of SMC handshake process.
At present, frequent visits will cause the incoming connections to be
backlogged in SMC handshake queue, raise the connections established
time. Which is quite unacceptable for those applications who base on
short lived connections.
There are two ways to implement this mechanism:
1. Put limitation after TCP established.
2. Put limitation before TCP established.
In the first way, we need to wait and receive CLC messages that the
client will potentially send, and then actively reply with a decline
message, in a sense, which is also a sort of SMC handshake, affect the
connections established time on its way.
In the second way, the only problem is that we need to inject SMC logic
into TCP when it is about to reply the incoming SYN, since we already do
that, it's seems not a problem anymore. And advantage is obvious, few
additional processes are required to complete the constraint.
This patch use the second way. After this patch, connections who beyond
constraint will not informed any SMC indication, and SMC will not be
involved in any of its subsequent processes.
Link: https://lore.kernel.org/all/1641301961-59331-1-git-send-email-alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation does not handling backlog semantics, one
potential risk is that server will be flooded by infinite amount
connections, even if client was SMC-incapable.
This patch works to put a limit on backlog connections, referring to the
TCP implementation, we divides SMC connections into two categories:
1. Half SMC connection, which includes all TCP established while SMC not
connections.
2. Full SMC connection, which includes all SMC established connections.
For half SMC connection, since all half SMC connections starts with TCP
established, we can achieve our goal by put a limit before TCP
established. Refer to the implementation of TCP, this limits will based
on not only the half SMC connections but also the full connections,
which is also a constraint on full SMC connections.
For full SMC connections, although we know exactly where it starts, it's
quite hard to put a limit before it. The easiest way is to block wait
before receive SMC confirm CLC message, while it's under protection by
smc_server_lgr_pending, a global lock, which leads this limit to the
entire host instead of a single listen socket. Another way is to drop
the full connections, but considering the cast of SMC connections, we
prefer to keep full SMC connections.
Even so, the limits of full SMC connections still exists, see commits
about half SMC connection below.
After this patch, the limits of backend connection shows like:
For SMC:
1. Client with SMC-capability can makes 2 * backlog full SMC connections
or 1 * backlog half SMC connections and 1 * backlog full SMC
connections at most.
2. Client without SMC-capability can only makes 1 * backlog half TCP
connections and 1 * backlog full TCP connections.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multithread and 10K connections benchmark, the backend TCP connection
established very slowly, and lots of TCP connections stay in SYN_SENT
state.
Client: smc_run wrk -c 10000 -t 4 http://server
the netstate of server host shows like:
145042 times the listen queue of a socket overflowed
145042 SYNs to LISTEN sockets dropped
One reason of this issue is that, since the smc_tcp_listen_work() shared
the same workqueue (smc_hs_wq) with smc_listen_work(), while the
smc_listen_work() do blocking wait for smc connection established. Once
the workqueue became congested, it's will block the accept() from TCP
listen.
This patch creates a independent workqueue(smc_tcp_ls_wq) for
smc_tcp_listen_work(), separate it from smc_listen_work(), which is
quite acceptable considering that smc_tcp_listen_work() runs very fast.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF,
avoid overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jlhJ
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF, avoid
overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload"
* tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (53 commits)
net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
net: mscc: ocelot: fix mutex lock error during ethtool stats read
ice: Avoid RTNL lock when re-creating auxiliary device
ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
ice: fix IPIP and SIT TSO offload
ice: fix an error code in ice_cfg_phy_fec()
net: mpls: Fix GCC 12 warning
dpaa2-eth: unregister the netdev before disconnecting from the PHY
skbuff: cleanup double word in comment
net: macb: Align the dma and coherent dma masks
mptcp: netlink: process IPv6 addrs in creating listening sockets
selftests: mptcp: add missing join check
net: usb: qmi_wwan: Add support for Dell DW5829e
vlan: move dev_put into vlan_dev_uninit
vlan: introduce vlan_dev_free_egress_priority
ax25: fix UAF bugs of net_device caused by rebinding operation
net: dsa: fix panic when DSA master device unbinds on shutdown
net: amd-xgbe: disable interrupts during pci removal
tipc: rate limit warning for received illegal binding update
net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
...
Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kmalloc(). For example:
struct switchdev_deferred_item {
...
unsigned long data[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 563f8e97e0 ("ipv4: Stop taking ECN bits into account in
fib4-rules") replaced the validation test on frh->tos. While the new
test is stricter for ECN bits, it doesn't detect the use of high order
DSCP bits. This would be fine if IPv4 could properly handle them. But
currently, most IPv4 lookups are done with the three high DSCP bits
masked. Therefore, using these bits doesn't lead to the expected
result.
Let's reject such configurations again, so that nobody starts to
use and make any assumption about how the stack handles the three high
order DSCP bits in fib4 rules.
Fixes: 563f8e97e0 ("ipv4: Stop taking ECN bits into account in fib4-rules")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having to acquire rtnl from netdev_run_todo() for every dismantled
device is not desirable when/if rtnl is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable outside the switch, which silences the warning:
./net/mpls/af_mpls.c:1624:21: error: statement will never be executed [-Werror=switch-unreachable]
1624 | int err;
| ^~~
Signed-off-by: Victor Erminpour <victor.erminpour@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor reordering of the code and a call to sock_cmsg_send()
gives us support for setting the common socket options via
cmsg (the usual ones - SO_MARK, SO_TIMESTAMPING_OLD, SCM_TXTIME).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing prevents the user from requesting timestamping
on ping6 sockets, yet timestamps are not going to be reported.
Plumb the flags through.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have ftrace and BPF today, there's no need for printing arguments
at the start of a function.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2022-02-10
An update from ieee802154 for your *net-next* tree.
There is more ongoing in ieee802154 than usual. This will be the first pull
request for this cycle, but I expect one more. Depending on review and rework
times.
Pavel Skripkin ported the atusb driver over to the new USB api to avoid unint
problems as well as making use of the modern api without kmalloc() needs in he
driver.
Miquel Raynal landed some changes to ensure proper frame checksum checking with
hwsim, documenting our use of wake and stop_queue and eliding a magic value by
using the proper define.
David Girault documented the address struct used in ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change updates mptcp_pm_nl_create_listen_socket() to create
listening sockets bound to IPv6 addresses (where IPv6 is supported).
Fixes: 1729cf186d ("mptcp: create the listening socket for new port")
Acked-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Conntrack sets on CHECKSUM_UNNECESSARY for UDP packet with no checksum,
from Kevin Mitchell.
2) skb->priority support for nfqueue, from Nicolas Dichtel.
3) Remove conntrack extension register API, from Florian Westphal.
4) Move nat destroy hook to nf_nat_hook instead, to remove
nf_ct_ext_destroy(), also from Florian.
5) Wrap pptp conntrack NAT hooks into single structure, from Florian Westphal.
6) Support for tcp option set to noop for nf_tables, also from Florian.
7) Do not run x_tables comment match from packet path in nf_tables,
from Florian Westphal.
8) Replace spinlock by cmpxchg() loop to update missed ct event,
from Florian Westphal.
9) Wrap cttimeout hooks into single structure, from Florian.
10) Add fast nft_cmp expression for up to 16-bytes.
11) Use cb->ctx to store context in ctnetlink dump, instead of using
cb->args[], from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: ctnetlink: use dump structure instead of raw args
nfqueue: enable to set skb->priority
netfilter: nft_cmp: optimize comparison for 16-bytes
netfilter: cttimeout: use option structure
netfilter: ecache: don't use nf_conn spinlock
netfilter: nft_compat: suppress comment match
netfilter: exthdr: add support for tcp option removal
netfilter: conntrack: pptp: use single option structure
netfilter: conntrack: remove extension register api
netfilter: conntrack: handle ->destroy hook via nat_ops instead
netfilter: conntrack: move extension sizes into core
netfilter: conntrack: make all extensions 8-byte alignned
netfilter: nfqueue: enable to get skb->priority
netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY
====================
Link: https://lore.kernel.org/r/20220209133616.165104-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit
9652dc2eb9 ("tcp: relax listening_hash operations")
removed the need to disable bottom half while acquiring
listening_hash.lock. There are still two callers left which disable
bottom half before the lock is acquired.
On PREEMPT_RT the softirqs are preemptible and local_bh_disable() acts
as a lock to ensure that resources, that are protected by disabling
bottom halves, remain protected.
This leads to a circular locking dependency if the lock acquired with
disabled bottom halves is also acquired with enabled bottom halves
followed by disabling bottom halves. This is the reverse locking order.
It has been observed with inet_listen_hashbucket:🔒
local_bh_disable() + spin_lock(&ilb->lock):
inet_listen()
inet_csk_listen_start()
sk->sk_prot->hash() := inet_hash()
local_bh_disable()
__inet_hash()
spin_lock(&ilb->lock);
acquire(&ilb->lock);
Reverse order: spin_lock(&ilb2->lock) + local_bh_disable():
tcp_seq_next()
listening_get_next()
spin_lock(&ilb2->lock);
acquire(&ilb2->lock);
tcp4_seq_show()
get_tcp4_sock()
sock_i_ino()
read_lock_bh(&sk->sk_callback_lock);
acquire(softirq_ctrl) // <---- whoops
acquire(&sk->sk_callback_lock)
Drop local_bh_disable() around __inet_hash() which acquires
listening_hash->lock. Split inet_unhash() and acquire the
listen_hashbucket lock without disabling bottom halves; the inet_ehash
lock with disabled bottom halves.
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/12d6f9879a97cd56c09fb53dee343cbb14f7f1f7.camel@gmx.de
Link: https://lkml.kernel.org/r/X9CheYjuXWc75Spa@hirez.programming.kicks-ass.net
Link: https://lore.kernel.org/r/YgQOebeZ10eNx1W6@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the commit c504e5c2f9 ("net: skb: introduce kfree_skb_reason()")
drop reason is introduced to the tracepoint of kfree_skb. Therefore,
drop_monitor is able to report the drop reason to users by netlink.
The drop reasons are reported as string to users, which is exactly
the same as what we do when reporting it to ftrace.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220209060838.55513-1-imagedong@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
