we added support to set the deleted flag prior to device scan,
then clear the flag for responding devices, leaving the deleted flag only
set for missing devices. The problem is for internal generated host resets,
IO queues are not blocked at scsi mid layer level. IO will be continued
sent to driver, and driver will return SCSI_MLQUEUE_HOST_BUSY. The problem
is the driver checks for the deleted flag before it checks for the
controller being in reset, so there is a window where the driver would be
returning DID_NO_CONNECT for responding devices. This occurs during the
time between calling _scsih_prep_device_scan, and
_scsih_mark_responding_sas_device & _scsih_mark_responding_raid_device.
Fix the queuecommand entry point so ioc->shost_recovery flag sanity check is
given higher presidence then the device "deleted flag" check.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add memcpy to mailbox completion to transfer reply correctly.
- Add support for BSG mailbox commands (dump, update_cfg, and
event_log_status).
- Add warning message and refuse mailbox command while mgmt is blocked.
- Add checks for memory allocation failure.
- Add check for sli4 dump zero BDE size.
- Only copy data if mailbox commands succeed.
- Add support for Read Event Log mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move the code to increase the sg seg count for LP21000 adapters.
- Check pcmd on command completion before dereferencing it.
- Clear queue memory when creating firmware queues to prevent stale entries.
- Replace the use of PAGE_SIZE in many areas that assumed it was always 4k.
- Add an else clause to a conditional that needed to unlock the hba_lock.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update driver for change in T10-PI interface on adapter
- Remove Profiles.
- Add new SLI Opcodes.
- Add new PDE structures used for BlockGuard.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent log message 1801 during vport delete.
- Enable NPIV by default.
- Display correct value for max Vports on SLI4 HBAs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added check before free_pages just to make sure ioc->scsi_lookup is not NULL.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support in the driver to support EEH and
PCIe Advanced Error Recovery. This involves adding new
pci_error_handler interface for recovering the controller from PCI Bus
errors, such as SERR and PERR. Some tools are available for simulating
PCI errors in order to validate this interface:
http://www.kernel.org/pub/linux/utils/pci/aer-inject
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be sending the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are few special cases which needs to be handled deleting old port.
CASE1: In topology you need cascaded expanders. Through sysfs just make sure
topology is up. Erase the manufacturing image of the cascaded expander and
reset the board. In some cases Adapter will receive Exapnder Add event
before expander delete. In such a case, driver needs to delete duplicate
port before adding new port.
CASE2: Enable Device Missing delay of HBA through lsiutils. If expander or
end device is hotswapped with different device before DMD timer expires,
driver will get device add for new device first and then device deletion
event for the original devices will arrive later at DMD timer expires. In
this case also driver need to delete duplicate port before adding port for
new device.
Added new function which will make sure when new port is
added, that its not claiming the same phy resources already in use by
another port. If it does, then it will delete the other port before adding
the new port.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
While testing the midlevel q_at_head and q_at_tail
patch for sg and the block SG_IO ioctl I found it
useful to reduce the queuing within the scsi_debug
driver. The reason is that the midlevel queue only
comes into play when the corresponding LLD queue
is full.
It is also useful when testing to be confident that
your program is the only thing issuing commands
to the (virtual) scsi_debug device. The no_uld=1
parameter will stop a scsi_debug virtual disk
appearing as /dev/sd* .
Changelog:
- add max_queue parameter to reduce the number
of queued commands the driver will accept.
This parameter can be changed after the driver
is loaded.
- add no_uld parameter that restricts scsi_debug's
virtual devices to the sg and bsg drivers
- correct stale url
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hazard testing uncovered yet another bug in sd. Under heavy reset
activity the retry counter might be exhausted and the command will be
returned with sense UNIT_ATTENTION/0x29/00 (POWER ON, RESET, OR BUS
DEVICE RESET OCCURRED). In those cases we should just increase the
retry counter again, retrying one more to clear up this Unit Attention
state.
[jejb: update to work with RC16 devices and not to loop endlessly]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After Host Reset firmware will have new list of device handles for the target.
Device handle refresh in driver is part of Rescan topology logic.
(See functions like *_search_responding_*). This needs to be done from Host
Reset context before making shost_recovery to 0. Currently it is done in
Firwmare event context, which may leads IO to a wrong device.
Now handler refresh is moved to HBA reset context.
Apart from this, Now driver will stop IOs for all device setting deleted
flag to 1 at the time of HBA Reset through _scsih_prep_device_scan.
It will only unblock devices, if devices has been found as part of RESCAN.
This way it will make more safe IO blocking at the time of HBA reset at
mpt2sas driver layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd always tries to submit a READ_CAPACITY(16) CDB,
regardless whether the host actually supports it.
queuecommand() will then return DID_ABORT, which is
not qualified enough to detect the true cause here.
So better check in sd_try_rc16 first if the cdblen
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When bnx2/cnic/bnx2i drivers are loaded in certain order, bnx2i will
will not initialize the device correctly because 'hba->cnic' will be
NULL when bnx2i_start() is called from register_device() context.
Under this condition 'ifdown' and 'ifup' of associated network
interface is required to bring iscsi adapter state to ready state so
that it will accept iscsi connection setup within the chip
Initializing 'hba->cnic' before calling register_device() will fix
this issue
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
instruct firmware to use driver/iscsid provided expected statsn field
while constructing login pdu header.
Initialize 'flags' to instruct chip to use driver/iscsid provided
ExpStatSN value while constructing iSCSI login PDU header
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the scsi eh is running and then a FC LLD calls
fc_remote_port_delete, the SCSI commands sent from the eh will fail.
To prevent this, a FC LLD can call fc_block_scsi_eh from the eh
callback, blocking the eh thread until the dev_loss_tmo fires or the
remote port is available again.
If (e.g. for a multipathing setup) the dev_loss_tmo is set to a very
large value, thus preventing the scsi device removal , the scsi eh can
block for a long time. For multipathing, the fast_io_fail_tmo is then
set to a low value to detect path problems sooner.
This patch introduces a new return code FAST_IO_FAIL. The function
fc_block_scsi_eh now returns FAST_IO_FAIL when the fast_io_fail_tmo
fires. This indicates that the LLD terminated all pending I/O requests
and there are no more pending SCSI commands for the scsi eh to wait
for. This return code can be passed back to the scsi eh to stop the
escalation and finish the recovery process for this device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default is enabled since 7e47e5ca18.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla84xx_mgmt_cmd function supports multiple subcommands.
Some subcommands require DMA memory and some do not.
Therefore check before freeing DMA memory whether it is allocated or not.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.
[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sg address in IO request is not set up correctly for big endian platform.
add new macros to properly swap the address.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
idr is a global resource, protect it with global bfad_mutex.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use pci_iomap() and pci_iounmap() to simplify the code. Remove uncessary #ifdef
check for ia64 (it was added as a workaound for some RHEL 5.x release which
doesn't export iounmap function)
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently the driver doesn't take into consideraion of possible sg chaining
when it walks through the sg list. This is fixed by using the sg_next()
which automatically handles the chaining case. Obosolete code is removed
as a result of this change.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use duplicate fc transport template for physical and vitual port. Add
vport create/delete/disalbe functions in the transport template of physical
port. Changes to make the vport create/delete function to work under this
framework.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1359) fixes a bug in scsi_alloc_target(). After a
device structure has been initialized (and especially after its name
has been set), it must not be freed directly. One has to call
put_device() instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1358) fixes a bug in the error pathway of
scsi_target_add(). If registration fails, the target should not be
reaped. The reaping occurs later, when scanning is finished and all
the child devices are removed. The current code leaves an unbalanced
value in starget->reap_ref.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be send the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added proper return type values in case memory allocation failed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed all the mutex's for ioc->tm_cmds.mutex, then created one
single mutex inside the function mpt2sas_scsih_issue_tm. This is the
single function used when sending task management. Also the sanity
checks required for scsi mid layer escalation were moved to inside the
same function because these checks need to be done while the mutex is
held. The ioc->tm_cmds.mutex inside the IOCTL branch is really not
required since there is another mutex in this code called for ctl_cmds
handling this sync.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Fixes for little endian issues.
2. Now Debug info for Discovery event is more readable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now Driver will not treat NEEDS_INIT as failure. In addition to this,
the driver will now display message to describe the the access flags
when bits are set, so the end user can better understand failures.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Aded checks for shost_recovery flag for early return from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
use the get_free_pages API for larger contigious physical memory chunk.
Also, the ioc->chain_depth need to be changed from
a 16bit to 32bit variable because the number of chains will exceed 64k
when the queue depth is large.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bug fix in the handling of the internal device reset event
The reason code check in scsih_sas_device_status_change_event never
evaluates as true for internal device reset, hence driver never quiesce s IO
when firmware is sending a device reset. The fix is to change the
evaluate to:
if (event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET &&
event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET)
return;
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
incorrect timestamp on 32 bit platforms: The upper 32 bit of
the timestamp was getting truncated when converting seconds to
milliseconds, which was due to the variable being long. To fix the problem,
the variable needs to be u64. Also the microseconds conversion to
milliseconds was incorrect; it should be divide by 1000 instead of divide by
8.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Setting handle to zero is not required before _scsih_remove_device.
Driver uses sas_device->handle reference in _scsih_remove_device.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Only abort outstanding I/O to force the OS to retry failed I/Os for AER
uncorrectable non-fatal errors instead of reseting the adapter.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add BSG support for PCI loopback testing.
- Add BSG support for extended mailbox commands.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
