Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This avoids another inderect call per RX packet which save us around
20-40 ns.
Changelog:
v1 -> v2:
- Move declaraions to fib_rules.h to remove warnings
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Note that the get case is pretty weird in that it actually copies data
back to userspace from setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreive a hash value from the SKB and store it
in the dissector key for future matching.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that touching linux/rhashtable.h causes lib/vsprintf.c to
be rebuilt. This dependency came through a bogus inclusion in the
file net/flow_offload.h. This patch moves it to the right place.
This patch also removes a lingering rhashtable inclusion in cls_api
created by the same commit.
Fixes: 4e481908c5 ("flow_offload: move tc indirect block to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 46 non-merge commits during the last 6 day(s) which contain
a total of 68 files changed, 4929 insertions(+), 526 deletions(-).
The main changes are:
1) Run BPF program on socket lookup, from Jakub.
2) Introduce cpumap, from Lorenzo.
3) s390 JIT fixes, from Ilya.
4) teach riscv JIT to emit compressed insns, from Luke.
5) use build time computed BTF ids in bpf iter, from Yonghong.
====================
Purely independent overlapping changes in both filter.h and xdp.h
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fe80536acf ("bareudp: Added attribute to enable & disable
rx metadata collection") breaks the the original(5.7) default behavior of
bareudp module to collect RX metadadata at the receive. It was added to
avoid the crash at the kernel neighbour subsytem when packet with metadata
from bareudp is processed. But it is no more needed as the
commit 394de110a7 ("net: Added pointer check for
dst->ops->neigh_lookup in dst_neigh_lookup_skb") solves this crash.
Fixes: fe80536acf ("bareudp: Added attribute to enable & disable rx metadata collection")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comment to describe the purpose of devlink instance lock.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the infrastructure in place for calling into the
dsa_ptr->netdev_ops function pointers, install them when we configure
the DSA CPU/management interface and tear them down. The flow is
unchanged from before, but now we preserve equality of tests when
network device drivers do tests like dev->netdev_ops == &foo_ops which
was not the case before since we were allocating an entirely new
structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the dsa_netdevice_ops structure which is a subset of
the net_device_ops structure for the specific operations that we care
about overlaying on top of the DSA CPU port net_device and provide
inline stubs that take core managing whether DSA code is reachable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setsockopt SOL_IP/IP_RECVERR_4884 to return the offset to an
extension struct if present.
ICMP messages may include an extension structure after the original
datagram. RFC 4884 standardized this behavior. It stores the offset
in words to the extension header in u8 icmphdr.un.reserved[1].
The field is valid only for ICMP types destination unreachable, time
exceeded and parameter problem, if length is at least 128 bytes and
entire packet does not exceed 576 bytes.
Return the offset to the start of the extension struct when reading an
ICMP error from the error queue, if it matches the above constraints.
Do not return the raw u8 field. Return the offset from the start of
the user buffer, in bytes. The kernel does not return the network and
transport headers, so subtract those.
Also validate the headers. Return the offset regardless of validation,
as an invalid extension must still not be misinterpreted as part of
the original datagram. Note that !invalid does not imply valid. If
the extension version does not match, no validation can take place,
for instance.
For backward compatibility, make this optional, set by setsockopt
SOL_IP/IP_RECVERR_RFC4884. For API example and feature test, see
github.com/wdebruij/kerneltools/blob/master/tests/recv_icmp_v2.c
For forward compatibility, reserve only setsockopt value 1, leaving
other bits for additional icmp extensions.
Changes
v1->v2:
- convert word offset to byte offset from start of user buffer
- return in ee_data as u8 may be insufficient
- define extension struct and object header structs
- return len only if constraints met
- if returning len, also validate
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_get_shared_info_from_{buff,frame} utility routines to get
skb_shared_info from xdp buffer/frame pointer.
xdp_get_shared_info_from_{buff,frame} will be used to implement xdp
multi-buffer support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compat handling to sock_common_{get,set}sockopt instead,
keyed of in_compat_syscall(). This allow to remove the now unused
->compat_{get,set}sockopt methods from struct proto_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper that copies either a native or compat bpf_fprog from
userspace after verifying the length, and remove the compat setsockopt
handlers that now aren't required.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirred currently does not mix well with blocks executed after the qdisc
root lock is taken. This includes classification blocks (such as in PRIO,
ETS, DRR qdiscs) and qevents. The locking caused by the packet mirrored by
mirred can cause deadlocks: either when the thread of execution attempts to
take the lock a second time, or when two threads end up waiting on each
other's locks.
The qevent patchset attempted to not introduce further badness of this
sort, and dropped the lock before executing the qevent block. However this
lead to too little locking and races between qdisc configuration and packet
enqueue in the RED qdisc.
Before the deadlock issues are solved in a way that can be applied across
many qdiscs reasonably easily, do for qevents what is done for the
classification blocks and just keep holding the root lock.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce XDP_REDIRECT support for eBPF programs attached to cpumap
entries.
This patch has been tested on Marvell ESPRESSObin using a modified
version of xdp_redirect_cpu sample in order to attach a XDP program
to CPUMAP entries to perform a redirect on the mvneta interface.
In particular the following scenario has been tested:
rq (cpu0) --> mvneta - XDP_REDIRECT (cpu0) --> CPUMAP - XDP_REDIRECT (cpu1) --> mvneta
$./xdp_redirect_cpu -p xdp_cpu_map0 -d eth0 -c 1 -e xdp_redirect \
-f xdp_redirect_kern.o -m tx_port -r eth0
tx: 285.2 Kpps rx: 285.2 Kpps
Attaching a simple XDP program on eth0 to perform XDP_TX gives
comparable results:
tx: 288.4 Kpps rx: 288.4 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/2cf8373a731867af302b00c4ff16c122630c4980.1594734381.git.lorenzo@kernel.org
Introduce the capability to attach an eBPF program to cpumap entries.
The idea behind this feature is to add the possibility to define on
which CPU run the eBPF program if the underlying hw does not support
RSS. Current supported verdicts are XDP_DROP and XDP_PASS.
This patch has been tested on Marvell ESPRESSObin using xdp_redirect_cpu
sample available in the kernel tree to identify possible performance
regressions. Results show there are no observable differences in
packet-per-second:
$./xdp_redirect_cpu --progname xdp_cpu_map0 --dev eth0 --cpu 1
rx: 354.8 Kpps
rx: 356.0 Kpps
rx: 356.8 Kpps
rx: 356.3 Kpps
rx: 356.6 Kpps
rx: 356.6 Kpps
rx: 356.7 Kpps
rx: 355.8 Kpps
rx: 356.8 Kpps
rx: 356.8 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/5c9febdf903d810b3415732e5cd98491d7d9067a.1594734381.git.lorenzo@kernel.org
Move the guts of xdp_convert_buff_to_frame to a new helper,
xdp_update_frame_from_buff so it can be reused removing code duplication
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/90a68c283d7ebeb48924934c9b7ac79492300472.1594734381.git.lorenzo@kernel.org
Drop doubled words in several comments.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "the" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "to" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled words "or" and "the" in several comments.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "not" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled words in two comments.
Fix a spello/typo.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 263e1201a2 ("mptcp: consolidate synack processing.")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not used since commit 09c7570480 ("xfrm: remove flow cache")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are not used any more since commit b1edeb1023 ("netlabel: Replace
protocol/NetLabel linking with refrerence counts")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend switchdev API to add support for MRP interconnect. The HW is
notified in the following cases:
SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role
of the node changes. The supported roles are MIM and MIC.
SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring
changes it states to open or closed.
SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending
MRP_InTest frames on all MRP ports. This is called only on nodes that
have the interconnect role MIM.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful for the user to know the reason behind a dropped packet.
Introduce new counters which track drops on the receive path caused by:
1. rx ring being full
2. fill ring being empty
Also, on the tx path introduce a counter which tracks the number of times
we attempt pull from the tx ring when it is empty.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-2-ciara.loftus@intel.com
