BB_A0 is a development model that is will not reach actual clients.
In fact, future firmware would simply fail to initialize such chip.
This changes the configuration into B0 instead of A0, and adds a safeguard
against the slim chance someone would actually try this with an A0 adapter
in which case probe would gracefully fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver learns the inner bar sized from a register configured by management
firmware, but older versions are not setting this register.
But since we know which values were configured back then, use them instead.
Signed-off-by: Ram Amrani <Ram.Amrani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch utilizes the attention infrastructure to log additional
information that relates only to specific HW blocks.
For some of those HW blocks, it also stops automatically disabling the
attention generation as the attention is considered benign and thus
should only be logged; No fear of it flooding the system.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each HW block contains common information about attention reasons,
raising a bit for each one of the different sub-reasons that caused it
to raise an attention.
This patch extends the infrastructure by allowing logging of the various
reasons causing the HW blocks to generate an attention.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW is capable of generating attentnions for a multitude of reasons,
but current driver is enabling attention generation only for management
firmware [required for link notifications].
This patch enables almost all of the possible reasons for HW attentions,
logging the HW block generating the attention and preventing further
attentions from that source [to prevent possible attention flood].
It also lays the infrastructure for additional exploration of the various
attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.
Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).
Caller will now have to choose whether to map via
write-combining API or not.
mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.
Fixes: 88a85f99e5 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By its role, there is no need to set all the other parameters
for the drop RQ.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For data cache locality considerations, we moved the nop and
csum_offload_inner within sq_stats struct as they are more
commonly accessed in xmit path.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the pair (channel, tc), we now use a single number that
goes over all tx queues of a TC, for all TCs.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More proper to declare carrier state UP only after the channels
are ready for traffic.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to flush the irq handler to make sure it does not
queue a work into the global work queue after we start to flush it.
So using synchronize_irq() is more appropriate than a spin lock.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to split or unsplit a port using the newly introduced
devlink ops.
Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting and unsplitting we'll destroy usable ports on the fly, so
mark them using a NULL pointer to indicate that their local port number
is free and can be re-used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.
When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.
When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.
Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port we replace it with 2 or 4 other ports. To be able
to do that we need to remove the original port netdev and unmap it from
its module. However, we first mark it as disabled, as active ports
cannot be unmapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add middle layer in mlxsw core code to forward port split/unsplit calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, there has been an mlx4-specific sysfs file allowing user to
change port type to either Ethernet of InfiniBand. This is very
inconvenient.
Allow to expose the same ability to set port type in a generic way
using devlink interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.
This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used to send NVM_FIND_DIR_ENTRY messages which can return error
if the entry is not found. This is normal and the error message will
cause unnecessary alarm, so silence it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_do_send_msg() to do essentially the same thing
with an additional paramter to silence error response messages. All
current callers will set silent to false.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For everything to fit, we remove the PHY microcode version and replace it
with the firmware package version in the fw_version string.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use appropriate firmware request header structure to prepare the
firmware messages. This avoids the unnecessary conversion of the
fields to 32-bit fields. Add appropriate endian conversion when
printing out the message fields in dmesg so that they appear correct
in the log.
Reported-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, we used a hardcoded value of 500 msec as the default
value for firmware message response timeout. For better portability with
future hardware or debug platforms, use the value provided by firmware in
the first response and store it for all susequent messages. Redefine the
macro HWRM_CMD_TIMEOUT to the stored value. Since we don't have the
value yet in the first message, use the 500 ms default if the stored value
is zero.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tx and rx rings don't share the same completion ring, tx coalescing
parameters can be set differently from the rx coalescing parameters.
Otherwise, use rx coalescing parameters on shared completion rings.
Adjust rx coalescing default values to lower interrupt rate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to set all the coalescing parameters. The function can
be used later to set both rx and tx coalescing parameters.
v2: Fixed function parameters formatting requested by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't convert these to internal hardware tick values before storing
them. This avoids the confusion of ethtool -c returning slightly
different values than the ones set using ethtool -C when we convert
hardware tick values back to micro seconds. Add better comments for
the hardware settings.
Also, rename the current set of coalescing fields with rx_ prefix.
The next patch will add support of tx coalescing values.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remove_one() when SRIOV is enabled, the PF driver
should broadcast PF driver unload notification to all
VFs that are attached to VMs. Upon receiving the PF
driver unload notification, the VF driver should print
a warning message to message log. Certain operations on the
VF may not succeed after the PF has unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VF to setup its own MAC address if the PF has not administratively
set it for the VF. To do that, we should always store the MAC address
from the firmware. There are 2 cases:
1. The MAC address is valid. This MAC address is assigned by the PF and
it needs to override the current VF MAC address.
2. The MAC address is zero. The VF will use a random MAC address by default.
By storing this 0 MAC address in the VF structure, it will allow the VF
user to change the MAC address later using ndo_set_mac_address() when
it sees that the stored MAC address is 0.
v2: Expanded descriptions and added more comments.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 5b6490def9 ("3c59x: Use setup_timer()") Amitoj
removed add_timer which sets up the epires timer. In this patch
the behavior is restore but it uses mod_timer which is a bit more
compact.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We intended to return PTR_ERR() here instead of 1.
Fixes: 1f9993f682 ('rocker: fix a neigh entry leak issue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-02-24
This series contains updates to e1000e, igb and igbvf.
Raanan provides updates for e1000e, first increases the ULP timer since it
now takes longer for the ULP exit to complete on Skylake. Fixes the
configuration of the internal hardware PHY clock gating mechanism, which was
causing packet loss due to mis configuring. Fixed additional ULP
configuration settings which were not being properly cleared after cable
connect in V-Pro capable systems. Added support for more i219 devices.
Takuma Ueba provides a fix for I210 where IPv6 autoconf test sometimes
fails due to DAD NS for link-local is not transmitted. To avoid this
issue, we need to wait until 1000BASE-T status register "Remote receiver
status OK".
Todd provides a patch to override EEPROM WoL settings for specific OEM
devices. Then renamed igb defines to be more generic, since the define
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part.
Roland Hii fixes an issue where only the half cycle time of less than or
equal to 70 millisecond uses the I210 clock output function. His patch
adds additional conditions when half cycle time is equal to 125 or 250 or
500 millisecond to use the clock output function.
Alex Duyck adds support for generic transmit checksums for igb and igbvf.
Jon Maxwell fixes an issues where customer applications are registering
and un-registering multicast addresses every few seconds which is leading
to many "Link is up" messages in the logs as a result of the
netif_carrier_off(netdev) in igbvf_msix_other(). So remove the
link is up message when registering multicast addresses.
Corinna Vinschen provides a fix for when switching off VLAN offloading on
i350, the VLAN interface becomes unusable.
Stefan Assmann updates the driver to use ndo_stop() instead of
dev_close() when running ethtool offline self test. Since dev_close()
causes IFF_UP to be cleared which will remove the interfaces routes
and some addresses.
v2: Dropped patches 6-10 in the original series. Patch 6-7 added support
for character device for AVB and based on community feedback, we do not
want to do this. Patches 8-10 provided fixes to the problematic code
added in patches 6 & 7. So all of them must go!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the `QL4xxx 40G/100G' and use `FastLinQ 4xxxx' instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't allow driver to probe on an adapter at a failed state;
Gracefully block the probe instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module is using a binary firmware file and so should be marked as such.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several corner cases where driver might get a 2nd notification
about the same link change. Don't log any additional changes if the
physical carrier is already reported as it should.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a corner-case in HW where an SKB queued for transmission that
contains too many frags will cause FW to assert.
This patch solves this by linearizing the SKB if necessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device ID for the 10g module has changed. Populate the pci_ids table
accordingly.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the use of kobj_to_dev() helper function instead of open
coding it with container_of()
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
expression a;
symbol kobj;
@@
- container_of(a, struct device, kobj)
+ kobj_to_dev(a)
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
The Coccinelle semantic patch that fixes this problem is
as follows:
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
...
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
The Coccinelle semantic patch that fixes this problem is
as follows:
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
The Coccinelle semantic patch that fixes this problem is
as follows:
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix endianness for the 64-bit hardware timestamp value with
be64_to_cpu to support both PowerPC platforms and ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace get_of_u32 with standard helper function of_property_read_u32
since the latter can process cpu endianness.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_GENEVE is built as a loadable module, and bnx2x is built-in,
we get this link error:
drivers/net/built-in.o: In function `bnx2x_open':
:(.text+0x33322): undefined reference to `geneve_get_rx_port'
drivers/net/built-in.o: In function `bnx2x_sp_rtnl_task':
:(.text+0x3e632): undefined reference to `geneve_get_rx_port'
This avoids the problem by adding a separate Kconfig symbol named
CONFIG_BNX2X_GENEVE that is only enabled when the code is
reachable from the driver.
This is the same trick that BNX2X does for VXLAN support, and
is similar to how I40E handles both.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 883ce97d25 ("bnx2x: Add Geneve inner-RSS support")
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
