forked from Minki/linux
123abc06e7
1045 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Vladimir Oltean
|
123abc06e7 |
net: dsa: add support for bridge TX forwarding offload
For a DSA switch, to offload the forwarding process of a bridge device
means to send the packets coming from the software bridge as data plane
packets. This is contrary to everything that DSA has done so far,
because the current taggers only know to send control packets (ones that
target a specific destination port), whereas data plane packets are
supposed to be forwarded according to the FDB lookup, much like packets
ingressing on any regular ingress port. If the FDB lookup process
returns multiple destination ports (flooding, multicast), then
replication is also handled by the switch hardware - the bridge only
sends a single packet and avoids the skb_clone().
DSA keeps for each bridge port a zero-based index (the number of the
bridge). Multiple ports performing TX forwarding offload to the same
bridge have the same dp->bridge_num value, and ports not offloading the
TX data plane of a bridge have dp->bridge_num = -1.
The tagger can check if the packet that is being transmitted on has
skb->offload_fwd_mark = true or not. If it does, it can be sure that the
packet belongs to the data plane of a bridge, further information about
which can be obtained based on dp->bridge_dev and dp->bridge_num.
It can then compose a DSA tag for injecting a data plane packet into
that bridge number.
For the switch driver side, we offer two new dsa_switch_ops methods,
called .port_bridge_fwd_offload_{add,del}, which are modeled after
.port_bridge_{join,leave}.
These methods are provided in case the driver needs to configure the
hardware to treat packets coming from that bridge software interface as
data plane packets. The switchdev <-> bridge interaction happens during
the netdev_master_upper_dev_link() call, so to switch drivers, the
effect is that the .port_bridge_fwd_offload_add() method is called
immediately after .port_bridge_join().
If the bridge number exceeds the number of bridges for which the switch
driver can offload the TX data plane (and this includes the case where
the driver can offload none), DSA falls back to simply returning
tx_fwd_offload = false in the switchdev_bridge_port_offload() call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
5b22d3669f |
net: dsa: track the number of switches in a tree
In preparation of supporting data plane forwarding on behalf of a software bridge, some drivers might need to view bridges as virtual switches behind the CPU port in a cross-chip topology. Give them some help and let them know how many physical switches there are in the tree, so that they can count the virtual switches starting from that number on. Note that the first dsa_switch_ops method where this information is reliably available is .setup(). This is because of how DSA works: in a tree with 3 switches, each calling dsa_register_switch(), the first 2 will advance until dsa_tree_setup() -> dsa_tree_setup_routing_table() and exit with error code 0 because the topology is not complete. Since probing is parallel at this point, one switch does not know about the existence of the other. Then the third switch comes, and for it, dsa_tree_setup_routing_table() returns complete = true. This switch goes ahead and calls dsa_tree_setup_switches() for everybody else, calling their .setup() methods too. This acts as the synchronization point. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Tobias Waldekranz
|
472111920f |
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded
Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
David S. Miller
|
5af84df962 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Conflicts are simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
4e51bf44a0 |
net: bridge: move the switchdev object replay helpers to "push" mode
Starting with commit |
||
|
Vladimir Oltean
|
2f5dc00f7a |
net: bridge: switchdev: let drivers inform which bridge ports are offloaded
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
Lino Sanfilippo
|
37120f23ac |
net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
If the checksum calculation is offloaded to the network device (e.g due to NETIF_F_HW_CSUM inherited from the DSA master device), the calculated layer 4 checksum is incorrect. This is since the DSA tag which is placed after the layer 4 data is considered as being part of the daa and thus errorneously included into the checksum calculation. To avoid this, always calculate the layer 4 checksum in software. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Lino Sanfilippo
|
21cf377a9c |
net: dsa: ensure linearized SKBs in case of tail taggers
The function skb_put() that is used by tail taggers to make room for the DSA tag must only be called for linearized SKBS. However in case that the slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the SKB passed to the slaves transmit function may not be linearized. Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags for tail taggers. Furthermore since the tagging protocol can be changed at runtime move the code for setting up the slaves features into dsa_slave_setup_tagger(). Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
b94dc99c0d |
net: dsa: use switchdev_handle_fdb_{add,del}_to_device
Using the new fan-out helper for FDB entries installed on the software bridge, we can install host addresses with the proper refcount on the CPU port, such that this case: ip link set swp0 master br0 ip link set swp1 master br0 ip link set swp2 master br0 ip link set swp3 master br0 ip link set br0 address 00:01:02:03:04:05 ip link set swp3 nomaster works properly and the br0 address remains installed as a host entry with refcount 3 instead of getting deleted. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
c6451cda10 |
net: switchdev: introduce helper for checking dynamically learned FDB entries
It is a bit difficult to understand what DSA checks when it tries to avoid installing dynamically learned addresses on foreign interfaces as local host addresses, so create a generic switchdev helper that can be reused and is generally more readable. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
c64b9c0504 |
net: dsa: tag_8021q: add proper cross-chip notifier support
The big problem which mandates cross-chip notifiers for tag_8021q is
this:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
When the user runs:
ip link add br0 type bridge
ip link set sw0p0 master br0
ip link set sw2p0 master br0
It doesn't work.
This is because dsa_8021q_crosschip_bridge_join() assumes that "ds" and
"other_ds" are at most 1 hop away from each other, so it is sufficient
to add the RX VLAN of {ds, port} into {other_ds, other_port} and vice
versa and presto, the cross-chip link works. When there is another
switch in the middle, such as in this case switch 1 with its DSA links
sw1p3 and sw1p4, somebody needs to tell it about these VLANs too.
Which is exactly why the problem is quadratic: when a port joins a
bridge, for each port in the tree that's already in that same bridge we
notify a tag_8021q VLAN addition of that port's RX VLAN to the entire
tree. It is a very complicated web of VLANs.
It must be mentioned that currently we install tag_8021q VLANs on too
many ports (DSA links - to be precise, on all of them). For example,
when sw2p0 joins br0, and assuming sw1p0 was part of br0 too, we add the
RX VLAN of sw2p0 on the DSA links of switch 0 too, even though there
isn't any port of switch 0 that is a member of br0 (at least yet).
In theory we could notify only the switches which sit in between the
port joining the bridge and the port reacting to that bridge_join event.
But in practice that is impossible, because of the way 'link' properties
are described in the device tree. The DSA bindings require DT writers to
list out not only the real/physical DSA links, but in fact the entire
routing table, like for example switch 0 above will have:
sw0p3: port@3 {
link = <&sw1p4 &sw2p4>;
};
This was done because:
/* TODO: ideally DSA ports would have a single dp->link_dp member,
* and no dst->rtable nor this struct dsa_link would be needed,
* but this would require some more complex tree walking,
* so keep it stupid at the moment and list them all.
*/
but it is a perfect example of a situation where too much information is
actively detrimential, because we are now in the position where we
cannot distinguish a real DSA link from one that is put there to avoid
the 'complex tree walking'. And because DT is ABI, there is not much we
can change.
And because we do not know which DSA links are real and which ones
aren't, we can't really know if DSA switch A is in the data path between
switches B and C, in the general case.
So this is why tag_8021q RX VLANs are added on all DSA links, and
probably why it will never change.
On the other hand, at least the number of additions/deletions is well
balanced, and this means that once we implement reference counting at
the cross-chip notifier level a la fdb/mdb, there is absolutely zero
need for a struct dsa_8021q_crosschip_link, it's all self-managing.
In fact, with the tag_8021q notifiers emitted from the bridge join
notifiers, it becomes so generic that sja1105 does not need to do
anything anymore, we can just delete its implementation of the
.crosschip_bridge_{join,leave} methods.
Among other things we can simply delete is the home-grown implementation
of sja1105_notify_crosschip_switches(). The reason why that is wrong is
because it is not quadratic - it only covers remote switches to which we
have a cross-chip bridging link and that does not cover in-between
switches. This deletion is part of the same patch because sja1105 used
to poke deep inside the guts of the tag_8021q context in order to do
that. Because the cross-chip links went away, so needs the sja1105 code.
Last but not least, dsa_8021q_setup_port() is simplified (and also
renamed). Because our TAG_8021Q_VLAN_ADD notifier is designed to react
on the CPU port too, the four dsa_8021q_vid_apply() calls:
- 1 for RX VLAN on user port
- 1 for the user port's RX VLAN on the CPU port
- 1 for TX VLAN on user port
- 1 for the user port's TX VLAN on the CPU port
now get squashed into only 2 notifier calls via
dsa_port_tag_8021q_vlan_add.
And because the notifiers to add and to delete a tag_8021q VLAN are
distinct, now we finally break up the port setup and teardown into
separate functions instead of relying on a "bool enabled" flag which
tells us what to do. Arguably it should have been this way from the
get go.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
e19cc13c9c |
net: dsa: tag_8021q: manage RX VLANs dynamically at bridge join/leave time
There has been at least one wasted opportunity for tag_8021q to be used by a driver: https://patchwork.ozlabs.org/project/netdev/patch/20200710113611.3398-3-kurt@linutronix.de/#2484272 because of a design decision: the declared purpose of tag_8021q is to offer source port/switch identification for a tagging driver for packets coming from a switch with no hardware DSA tagging support. It is not intended to provide VLAN-based port isolation, because its first user, sja1105, had another mechanism for bridging domain isolation, the L2 Forwarding Table. So even if 2 ports are in the same VLAN but they are separated via the L2 Forwarding Table, they will not communicate with one another. The L2 Forwarding Table is managed by the sja1105_bridge_join() and sja1105_bridge_leave() methods. As a consequence, today tag_8021q does not bother too much with hooking into .port_bridge_join() and .port_bridge_leave() because that would introduce yet another degree of freedom, it just iterates statically through all ports of a switch and adds the RX VLAN of one port to all the others. In this way, whenever .port_bridge_join() is called, bridging will magically work because the RX VLANs are already installed everywhere they need to be. This is not to say that the reason for the change in this patch is to satisfy the hellcreek and similar use cases, that is merely a nice side effect. Instead it is to make sja1105 cross-chip links work properly over a DSA link. For context, sja1105 today supports a degenerate form of cross-chip bridging, where the switches are interconnected through their CPU ports ("disjoint trees" topology). There is some code which has been generalized into dsa_8021q_crosschip_link_{add,del}, but it is not enough, and frankly it is impossible to build upon that. Real multi-switch DSA trees, like daisy chains or H trees, which have actual DSA links, do not work. The problem is that sja1105 is unlike mv88e6xxx, and does not have a PVT for cross-chip bridging, which is a table by which the local switch can select the forwarding domain for packets from a certain ingress switch ID and source port. The sja1105 switches cannot parse their own DSA tags, because, well, they don't really have support for DSA tags, it's all VLANs. So to make something like cross-chip bridging between sw0p0 and sw1p0 to work over the sw0p3/sw1p3 DSA link to work with sja1105 in the topology below: | | sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0 [ user ] [ user ] [ cpu ] [ dsa ] ---- [ dsa ] [ cpu ] [ user ] [ user ] we need to ask ourselves 2 questions: (1) how should the L2 Forwarding Table be managed? (2) how should the VLAN Lookup Table be managed? i.e. what should prevent packets from going to unwanted ports? Since as mentioned, there is no PVT, the L2 Forwarding Table only contains forwarding rules for local ports. So we can say "all user ports are allowed to forward to all CPU ports and all DSA links". If we allow forwarding to DSA links unconditionally, this means we must prevent forwarding using the VLAN Lookup Table. This is in fact asymmetric with what we do for tag_8021q on ports local to the same switch, and it matters because now that we are making tag_8021q a core DSA feature, we need to hook into .crosschip_bridge_join() to add/remove the tag_8021q VLANs. So for symmetry it makes sense to manage the VLANs for local forwarding in the same way as cross-chip forwarding. Note that there is a very precise reason why tag_8021q hooks into dsa_switch_bridge_join() which acts at the cross-chip notifier level, and not at a higher level such as dsa_port_bridge_join(). We need to install the RX VLAN of the newly joining port into the VLAN table of all the existing ports across the tree that are part of the same bridge, and the notifier already does the iteration through the switches for us. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
328621f613 |
net: dsa: tag_8021q: absorb dsa_8021q_setup into dsa_tag_8021q_{,un}register
Right now, setting up tag_8021q is a 2-step operation for a driver, first the context structure needs to be created, then the VLANs need to be installed on the ports. A similar thing is true for teardown. Merge the 2 steps into the register/unregister methods, to be as transparent as possible for the driver as to what tag_8021q does behind the scenes. This also gets rid of the funny "bool setup == true means setup, == false means teardown" API that tag_8021q used to expose. Note that dsa_tag_8021q_register() must be called at least in the .setup() driver method and never earlier (like in the driver probe function). This is because the DSA switch tree is not initialized at probe time, and the cross-chip notifiers will not work. For symmetry with .setup(), the unregister method should be put in .teardown(). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
5da11eb407 |
net: dsa: make tag_8021q operations part of the core
Make tag_8021q a more central element of DSA and move the 2 driver specific operations outside of struct dsa_8021q_context (which is supposed to hold dynamic data and not really constant function pointers). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
d7b1fd520d |
net: dsa: let the core manage the tag_8021q context
The basic problem description is as follows:
Be there 3 switches in a daisy chain topology:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
The CPU will not be able to ping through the user ports of the
bottom-most switch (like for example sw2p0), simply because tag_8021q
was not coded up for this scenario - it has always assumed DSA switch
trees with a single switch.
To add support for the topology above, we must admit that the RX VLAN of
sw2p0 must be added on some ports of switches 0 and 1 as well. This is
in fact a textbook example of thing that can use the cross-chip notifier
framework that DSA has set up in switch.c.
There is only one problem: core DSA (switch.c) is not able right now to
make the connection between a struct dsa_switch *ds and a struct
dsa_8021q_context *ctx. Right now, it is drivers who call into
tag_8021q.c and always provide a struct dsa_8021q_context *ctx pointer,
and tag_8021q.c calls them back with the .tag_8021q_vlan_{add,del}
methods.
But with cross-chip notifiers, it is possible for tag_8021q to call
drivers without drivers having ever asked for anything. A good example
is right above: when sw2p0 wants to set itself up for tag_8021q,
the .tag_8021q_vlan_add method needs to be called for switches 1 and 0,
so that they transport sw2p0's VLANs towards the CPU without dropping
them.
So instead of letting drivers manage the tag_8021q context, add a
tag_8021q_ctx pointer inside of struct dsa_switch, which will be
populated when dsa_tag_8021q_register() returns success.
The patch is fairly long-winded because we are partly reverting commit
|
||
|
Vladimir Oltean
|
8b6e638b4b |
net: dsa: build tag_8021q.c as part of DSA core
Upcoming patches will add tag_8021q related logic to switch.c and port.c, in order to allow it to make use of cross-chip notifiers. In addition, a struct dsa_8021q_context *ctx pointer will be added to struct dsa_switch. It seems fairly low-reward to #ifdef the *ctx from struct dsa_switch and to provide shim implementations of the entire tag_8021q.c calling surface (not even clear what to do about the tag_8021q cross-chip notifiers to avoid compiling them). The runtime overhead for switches which don't use tag_8021q is fairly small because all helpers will check for ds->tag_8021q_ctx being a NULL pointer and stop there. So let's make it part of dsa_core.o. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
cedf467064 |
net: dsa: tag_8021q: create dsa_tag_8021q_{register,unregister} helpers
In preparation of moving tag_8021q to core DSA, move all initialization and teardown related to tag_8021q which is currently done by drivers in 2 functions called "register" and "unregister". These will gather more functionality in future patches, which will better justify the chosen naming scheme. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
69ebb37064 |
net: dsa: tag_8021q: use symbolic error names
Use %pe to give the user a string holding the error code instead of just a number. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
a81a45744b |
net: dsa: tag_8021q: use "err" consistently instead of "rc"
Some of the tag_8021q code has been taken out of sja1105, which uses "rc" for its return code variables, whereas the DSA core uses "err". Change tag_8021q for consistency. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
0fac6aa098 |
net: dsa: sja1105: delete the best_effort_vlan_filtering mode
Simply put, the best-effort VLAN filtering mode relied on VLAN retagging from a bridge VLAN towards a tag_8021q sub-VLAN in order to be able to decode the source port in the tagger, but the VLAN retagging implementation inside the sja1105 chips is not the best and we were relying on marginal operating conditions. The most notable limitation of the best-effort VLAN filtering mode is its incapacity to treat this case properly: ip link add br0 type bridge vlan_filtering 1 ip link set swp2 master br0 ip link set swp4 master br0 bridge vlan del dev swp4 vid 1 bridge vlan add dev swp4 vid 1 pvid When sending an untagged packet through swp2, the expectation is for it to be forwarded to swp4 as egress-tagged (so it will contain VLAN ID 1 on egress). But the switch will send it as egress-untagged. There was an attempt to fix this here: https://patchwork.kernel.org/project/netdevbpf/patch/20210407201452.1703261-2-olteanv@gmail.com/ but it failed miserably because it broke PTP RX timestamping, in a way that cannot be corrected due to hardware issues related to VLAN retagging. So with either PTP broken or pushing VLAN headers on egress for untagged packets being broken, the sad reality is that the best-effort VLAN filtering code is broken. Delete it. Note that this means there will be a temporary loss of functionality in this driver until it is replaced with something better (network stack RX/TX capability for "mode 2" as described in Documentation/networking/dsa/sja1105.rst, the "port under VLAN-aware bridge" case). We simply cannot keep this code until that driver rework is done, it is super bloated and tangled with tag_8021q. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
bcb9928a15 |
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
This was not caught because there is no switch driver which implements
the .port_bridge_join but not .port_bridge_leave method, but it should
nonetheless be fixed, as in certain conditions (driver development) it
might lead to NULL pointer dereference.
Fixes:
|
||
|
Vladimir Oltean
|
b71d098715 |
net: dsa: return -EOPNOTSUPP when driver does not implement .port_lag_join
The DSA core has a layered structure, and even though we end up returning 0 (success) to user space when setting a bonding/team upper that can't be offloaded, some parts of the framework actually need to know that we couldn't offload that. For example, if dsa_switch_lag_join returns 0 as it currently does, dsa_port_lag_join has no way to tell a successful offload from a software fallback, and it will call dsa_port_bridge_join afterwards. Then we'll think we're offloading the bridge master of the LAG, when in fact we're not even offloading the LAG. In turn, this will make us set skb->offload_fwd_mark = true, which is incorrect and the bridge doesn't like it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
63c51453c8 |
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
When we join a bridge that already has some local addresses pointing to itself, we do not get those notifications. Similarly, when we leave that bridge, we do not get notifications for the deletion of those entries. The only switchdev notifications we get are those of entries added while the DSA port is enslaved to the bridge. This makes use cases such as the following work properly (with the number of additions and removals properly balanced): ip link add br0 type bridge ip link add br1 type bridge ip link set br0 address 00:01:02:03:04:05 ip link set br1 address 00:01:02:03:04:05 ip link set swp0 up ip link set swp1 up ip link set swp0 master br0 ip link set swp1 master br1 ip link set br0 up ip link set br1 up ip link del br1 # 00:01:02:03:04:05 still installed on the CPU port ip link del br0 # 00:01:02:03:04:05 finally removed from the CPU port Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
4bed397c3e |
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
When
(a) "dev" is a bridge port which the DSA switch tree offloads, but is
otherwise not a dsa slave (such as a LAG netdev), or
(b) "dev" is the bridge net device itself
then strange things happen to the dev_hold/dev_put pair:
dsa_schedule_work() will still be called with a DSA port that offloads
that netdev, but dev_hold() will be called on the non-DSA netdev.
Then the "if" condition in dsa_slave_switchdev_event_work() does not
pass, because "dev" is not a DSA netdev, so dev_put() is not called.
This results in the simple fact that we have a reference counting
mismatch on the "dev" net device.
This can be seen when we add support for host addresses installed on the
bridge net device.
ip link add br1 type bridge
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 master br1
ip link del br1
[ 968.512278] unregister_netdevice: waiting for br1 to become free. Usage count = 5
It seems foolish to do penny pinching and not add the net_device pointer
in the dsa_switchdev_event_work structure, so let's finally do that.
As an added bonus, when we start offloading local entries pointing
towards the bridge, these will now properly appear as 'offloaded' in
'bridge fdb' (this was not possible before, because 'dev' was assumed to
only be a DSA net device):
00:01:02:03:04:05 dev br0 vlan 1 offload master br0 permanent
00:01:02:03:04:05 dev br0 offload master br0 permanent
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
81a619f787 |
net: dsa: include fdb entries pointing to bridge in the host fdb list
The bridge supports a legacy way of adding local (non-forwarded) FDB
entries, which works on an individual port basis:
bridge fdb add dev swp0 00:01:02:03:04:05 master local
As well as a new way, added by Roopa Prabhu in commit
|
||
|
Tobias Waldekranz
|
10fae4ac89 |
net: dsa: include bridge addresses which are local in the host fdb list
The bridge automatically creates local (not forwarded) fdb entries pointing towards physical ports with their interface MAC addresses. For switchdev, the significance of these fdb entries is the exact opposite of that of non-local entries: instead of sending these frame outwards, we must send them inwards (towards the host). NOTE: The bridge's own MAC address is also "local". If that address is not shared with any port, the bridge's MAC is not be added by this functionality - but the following commit takes care of that case. NOTE 2: We mark these addresses as host-filtered regardless of the value of ds->assisted_learning_on_cpu_port. This is because, as opposed to the speculative logic done for dynamic address learning on foreign interfaces, the local FDB entries are rather fixed, so there isn't any risk of them migrating from one bridge port to another. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
3068d466a6 |
net: dsa: sync static FDB entries on foreign interfaces to hardware
DSA is able to install FDB entries towards the CPU port for addresses which were dynamically learnt by the software bridge on foreign interfaces that are in the same bridge with a DSA switch interface. Since this behavior is opportunistic, it is guarded by the "assisted_learning_on_cpu_port" property which can be enabled by drivers and is not done automatically (since certain switches may support address learning of packets coming from the CPU port). But if those FDB entries added on the foreign interfaces are static (added by the user) instead of dynamically learnt, currently DSA does not do anything (and arguably it should). Because static FDB entries are not supposed to move on their own, there is no downside in reusing the "assisted_learning_on_cpu_port" logic to sync static FDB entries to the DSA CPU port unconditionally, even if assisted_learning_on_cpu_port is not requested by the driver. For example, this situation: br0 / \ swp0 dummy0 $ bridge fdb add 02:00:de:ad:00:01 dev dummy0 vlan 1 master static Results in DSA adding an entry in the hardware FDB, pointing this address towards the CPU port. The same is true for entries added to the bridge itself, e.g: $ bridge fdb add 02:00:de:ad:00:01 dev br0 vlan 1 self local (except that right now, DSA still ignores 'local' FDB entries, this will be changed in a later patch) Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
26ee7b06a4 |
net: dsa: install the host MDB and FDB entries in the master's RX filter
If the DSA master implements strict address filtering, then the unicast and multicast addresses kept by the DSA CPU ports should be synchronized with the address lists of the DSA master. Note that we want the synchronization of the master's address lists even if the DSA switch doesn't support unicast/multicast database operations, on the premises that the packets will be flooded to the CPU in that case, and we should still instruct the master to receive them. This is why we do the dev_uc_add() etc first, even if dsa_port_notify() returns -EOPNOTSUPP. In turn, dev_uc_add() and friends return error only if memory allocation fails, so it is probably ok to check and propagate that error code and not just ignore it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
3f6e32f92a |
net: dsa: reference count the FDB addresses at the cross-chip notifier level
The same concerns expressed for host MDB entries are valid for host FDBs just as well: - in the case of multiple bridges spanning the same switch chip, deleting a host FDB entry that belongs to one bridge will result in breakage to the other bridge - not deleting FDB entries across DSA links means that the switch's hardware tables will eventually run out, given enough wear&tear So do the same thing and introduce reference counting for CPU ports and DSA links using the same data structures as we have for MDB entries. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
3dc80afc50 |
net: dsa: introduce a separate cross-chip notifier type for host FDBs
DSA treats some bridge FDB entries by trapping them to the CPU port. Currently, the only class of such entries are FDB addresses learnt by the software bridge on a foreign interface. However there are many more to be added: - FDB entries with the is_local flag (for termination) added by the bridge on the user ports (typically containing the MAC address of the bridge port) - FDB entries pointing towards the bridge net device (for termination). Typically these contain the MAC address of the bridge net device. - Static FDB entries installed on a foreign interface that is in the same bridge with a DSA user port. The reason why a separate cross-chip notifier for host FDBs is justified compared to normal FDBs is the same as in the case of host MDBs: the cross-chip notifier matching function in switch.c should avoid installing these entries on routing ports that route towards the targeted switch, but not towards the CPU. This is required in order to have proper support for H-like multi-chip topologies. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
161ca59d39 |
net: dsa: reference count the MDB entries at the cross-chip notifier level
Ever since the cross-chip notifiers were introduced, the design was
meant to be simplistic and just get the job done without worrying too
much about dangling resources left behind.
For example, somebody installs an MDB entry on sw0p0 in this daisy chain
topology. It gets installed using ds->ops->port_mdb_add() on sw0p0,
sw1p4 and sw2p4.
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Then the same person deletes that MDB entry. The cross-chip notifier for
deletion only matches sw0p0:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
Why?
Because the DSA links are 'trunk' ports, if we just go ahead and delete
the MDB from sw1p4 and sw2p4 directly, we might delete those multicast
entries when they are still needed. Just consider the fact that somebody
does:
- add a multicast MAC address towards sw0p0 [ via the cross-chip
notifiers it gets installed on the DSA links too ]
- add the same multicast MAC address towards sw0p1 (another port of that
same switch)
- delete the same multicast MAC address from sw0p0.
At this point, if we deleted the MAC address from the DSA links, it
would be flooded, even though there is still an entry on switch 0 which
needs it not to.
So that is why deletions only match the targeted source port and nothing
on DSA links. Of course, dangling resources means that the hardware
tables will eventually run out given enough additions/removals, but hey,
at least it's simple.
But there is a bigger concern which needs to be addressed, and that is
our support for SWITCHDEV_OBJ_ID_HOST_MDB. DSA simply translates such an
object into a dsa_port_host_mdb_add() which ends up as ds->ops->port_mdb_add()
on the upstream port, and a similar thing happens on deletion:
dsa_port_host_mdb_del() will trigger ds->ops->port_mdb_del() on the
upstream port.
When there are 2 VLAN-unaware bridges spanning the same switch (which is
a use case DSA proudly supports), each bridge will install its own
SWITCHDEV_OBJ_ID_HOST_MDB entries. But upon deletion, DSA goes ahead and
emits a DSA_NOTIFIER_MDB_DEL for dp->cpu_dp, which is shared between the
user ports enslaved to br0 and the user ports enslaved to br1. Not good.
The host-trapped multicast addresses installed by br1 will be deleted
when any state changes in br0 (IGMP timers expire, or ports leave, etc).
To avoid this, we could of course go the route of the zero-sum game and
delete the DSA_NOTIFIER_MDB_DEL call for dp->cpu_dp. But the better
design is to just admit that on shared ports like DSA links and CPU
ports, we should be reference counting calls, even if this consumes some
dynamic memory which DSA has traditionally avoided. On the flip side,
the hardware tables of switches are limited in size, so it would be good
if the OS managed them properly instead of having them eventually
overflow.
To address the memory usage concern, we only apply the refcounting of
MDB entries on ports that are really shared (CPU ports and DSA links)
and not on user ports. In a typical single-switch setup, this means only
the CPU port (and the host MDB entries are not that many, really).
The name of the newly introduced data structures (dsa_mac_addr) is
chosen in such a way that will be reusable for host FDB entries (next
patch).
With this change, we can finally have the same matching logic for the
MDB additions and deletions, as well as for their host-trapped variants.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
b8e997c490 |
net: dsa: introduce a separate cross-chip notifier type for host MDBs
Commit
|
||
|
Vladimir Oltean
|
b117e1e8a8 |
net: dsa: delete dsa_legacy_fdb_add and dsa_legacy_fdb_del
We want to add reference counting for FDB entries in cross-chip topologies, and in order for that to have any chance of working and not be unbalanced (leading to entries which are never deleted), we need to ensure that higher layers are sane, because if they aren't, it's garbage in, garbage out. For example, if we add a bridge FDB entry twice, the bridge properly errors out: $ bridge fdb add dev swp0 00:01:02:03:04:07 master static $ bridge fdb add dev swp0 00:01:02:03:04:07 master static RTNETLINK answers: File exists However, the same thing cannot be said about the bridge bypass operations: $ bridge fdb add dev swp0 00:01:02:03:04:07 $ bridge fdb add dev swp0 00:01:02:03:04:07 $ bridge fdb add dev swp0 00:01:02:03:04:07 $ bridge fdb add dev swp0 00:01:02:03:04:07 $ echo $? 0 But one 'bridge fdb del' is enough to remove the entry, no matter how many times it was added. The bridge bypass operations are impossible to maintain in these circumstances and lack of support for reference counting the cross-chip notifiers is holding us back from making further progress, so just drop support for them. The only way left for users to install static bridge FDB entries is the proper one, using the "master static" flags. With this change, rtnl_fdb_add() falls back to calling ndo_dflt_fdb_add() which uses the duplicate-exclusive variant of dev_uc_add(): dev_uc_add_excl(). Because DSA does not (yet) declare IFF_UNICAST_FLT, this results in us going to promiscuous mode: $ bridge fdb add dev swp0 00:01:02:03:04:05 [ 28.206743] device swp0 entered promiscuous mode $ bridge fdb add dev swp0 00:01:02:03:04:05 RTNETLINK answers: File exists So even if it does not completely fail, there is at least some indication that it is behaving differently from before, and closer to user space expectations, I would argue (the lack of a "local|static" specifier defaults to "local", or "host-only", so dev_uc_add() is a reasonable default implementation). If the generic implementation of .ndo_fdb_add provided by Vlad Yasevich is a proof of anything, it only proves that the implementation provided by DSA was always wrong, by not looking at "ndm->ndm_state & NUD_NOARP" (the "static" flag which means that the FDB entry points outwards) and "ndm->ndm_state & NUD_PERMANENT" (the "local" flag which means that the FDB entry points towards the host). It all used to mean the same thing to DSA. Update the documentation so that the users are not confused about what's going on. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
7491894532 |
net: dsa: replay a deletion of switchdev objects for ports leaving a bridged LAG
When a DSA switch port leaves a bonding interface that is under a bridge, there might be dangling switchdev objects on that port left behind, because the bridge is not aware that its lower interface (the bond) changed state in any way. Call the bridge replay helpers with adding=false before changing dp->bridge_dev to NULL, because we need to simulate to dsa_slave_port_obj_del() that these notifications were emitted by the bridge. We add this hook to the NETDEV_PRECHANGEUPPER event handler, because we are calling into switchdev (and the __switchdev_handle_port_obj_del fanout helpers expect the upper/lower adjacency lists to still be valid) and PRECHANGEUPPER is the last moment in time when they still are. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
4ede74e73b |
net: dsa: refactor the prechangeupper sanity checks into a dedicated function
We need to add more logic to the DSA NETDEV_PRECHANGEUPPER event handler, more exactly we need to request an unsync of switchdev objects. In order to fit more code, refactor the existing logic into a helper. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
7e8c18586d |
net: bridge: allow the switchdev replay functions to be called for deletion
When a switchdev port leaves a LAG that is a bridge port, the switchdev objects and port attributes offloaded to that port are not removed: ip link add br0 type bridge ip link add bond0 type bond mode 802.3ad ip link set swp0 master bond0 ip link set bond0 master br0 bridge vlan add dev bond0 vid 100 ip link set swp0 nomaster VLAN 100 will remain installed on swp0 despite it going into standalone mode, because as far as the bridge is concerned, nothing ever happened to its bridge port. Let's extend the bridge vlan, fdb and mdb replay functions to take a 'bool adding' argument, and make DSA and ocelot call the replay functions with 'adding' as false from the switchdev unsync path, for the switch port that leaves the bridge. Note that this patch in itself does not salvage anything, because in the current pull mode of operation, DSA still needs to call the replay helpers with adding=false. This will be done in another patch. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
0d2cfbd41c |
net: bridge: ignore switchdev events for LAG ports which didn't request replay
There is a slight inconvenience in the switchdev replay helpers added recently, and this is when: ip link add br0 type bridge ip link add bond0 type bond ip link set bond0 master br0 bridge vlan add dev bond0 vid 100 ip link set swp0 master bond0 ip link set swp1 master bond0 Since the underlying driver (currently only DSA) asks for a replay of VLANs when swp0 and swp1 join the LAG because it is bridged, what will happen is that DSA will try to react twice on the VLAN event for swp0. This is not really a huge problem right now, because most drivers accept duplicates since the bridge itself does, but it will become a problem when we add support for replaying switchdev object deletions. Let's fix this by adding a blank void *ctx in the replay helpers, which will be passed on by the bridge in the switchdev notifications. If the context is NULL, everything is the same as before. But if the context is populated with a valid pointer, the underlying switchdev driver (currently DSA) can use the pointer to 'see through' the bridge port (which in the example above is bond0) and 'know' that the event is only for a particular physical port offloading that bridge port, and not for all of them. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
69bfac968a |
net: switchdev: add a context void pointer to struct switchdev_notifier_info
In the case where the driver asks for a replay of a certain type of event (port object or attribute) for a bridge port that is a LAG, it may do so because this port has just joined the LAG. But there might already be other switchdev ports in that LAG, and it is preferable that those preexisting switchdev ports do not act upon the replayed event. The solution is to add a context to switchdev events, which is NULL most of the time (when the bridge layer initiates the call) but which can be set to a value controlled by the switchdev driver when a replay is requested. The driver can then check the context to figure out if all ports within the LAG should act upon the switchdev event, or just the ones that match the context. We have to modify all switchdev_handle_* helper functions as well as the prototypes in the drivers that use these helpers too, because these helpers hide the underlying struct switchdev_notifier_info from us and there is no way to retrieve the context otherwise. The context structure will be populated and used in later patches. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
f9bcdc362c |
net: dsa: remove cross-chip support from the MRP notifiers
With MRP hardware assist being supported only by the ocelot switch family, which by design does not support cross-chip bridging, the current match functions are at best a guess and have not been confirmed in any way to do anything relevant in a multi-switch topology. Drop the code and make the notifiers match only on the targeted switch port. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
88faba20e2 |
net: dsa: targeted MTU notifiers should only match on one port
dsa_slave_change_mtu() calls dsa_port_mtu_change() twice:
- it sends a cross-chip notifier with the MTU of the CPU port which is
used to update the DSA links.
- it sends one targeted MTU notifier which is supposed to only match the
user port on which we are changing the MTU. The "propagate_upstream"
variable is used here to bypass the cross-chip notifier system from
switch.c
But due to a mistake, the second, targeted notifier matches not only on
the user port, but also on the DSA link which is a member of the same
switch, if that exists.
And because the DSA links of the entire dst were programmed in a
previous round to the largest_mtu via a "propagate_upstream == true"
notification, then the dsa_port_mtu_change(propagate_upstream == false)
call that is immediately upcoming will break the MTU on the one DSA link
which is chip-wise local to the dp whose MTU is changing right now.
Example given this daisy chain topology:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
ip link set sw0p1 mtu 9000
ip link set sw1p1 mtu 9000 # at this stage, sw0p1 and sw1p1 can talk
# to one another using jumbo frames
ip link set sw0p2 mtu 1500 # this programs the sw0p3 DSA link first to
# the largest_mtu of 9000, then reprograms it to
# 1500 with the "propagate_upstream == false"
# notifier, breaking communication between
# sw0p1 and sw1p1
To escape from this situation, make the targeted match really match on a
single port - the user port, and rename the "propagate_upstream"
variable to "targeted_match" to clarify the intention and avoid future
issues.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
4e4ab79500 |
net: dsa: calculate the largest_mtu across all ports in the tree
If we have a cross-chip topology like this:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
and we issue the following commands:
1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600
we notice the following happening:
Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).
Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.
As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.
To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
abd49535c3 |
net: dsa: execute dsa_switch_mdb_add only for routing port in cross-chip topologies
Currently, the notifier for adding a multicast MAC address matches on
the targeted port and on all DSA links in the system, be they upstream
or downstream links.
This leads to a considerable amount of useless traffic.
Consider this daisy chain topology, and a MDB add notifier emitted on
sw0p0. It matches on sw0p0, sw0p3, sw1p3 and sw2p4.
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ x ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
But switch 0 has no reason to send the multicast traffic for that MAC
address on sw0p3, which is how it reaches switches 1 and 2. Those
switches don't expect, according to the user configuration, to receive
this multicast address from switch 1, and they will drop it anyway,
because the only valid destination is the port they received it on.
They only need to configure themselves to deliver that multicast address
_towards_ switch 1, where the MDB entry is installed.
Similarly, switch 1 should not send this multicast traffic towards
sw1p3, because that is how it reaches switch 2.
With this change, the heat map for this MDB notifier changes as follows:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Now the mdb notifier behaves the same as the fdb notifier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
a8986681cc |
net: dsa: export the dsa_port_is_{user,cpu,dsa} helpers
The difference between dsa_is_user_port and dsa_port_is_user is that the former needs to look up the list of ports of the DSA switch tree in order to find the struct dsa_port, while the latter directly receives it as an argument. dsa_is_user_port is already in widespread use and has its place, so there isn't any chance of converting all callers to a single form. But being able to do: dsa_port_is_user(dp) instead of dsa_is_user_port(dp->ds, dp->index) is much more efficient too, especially when the "dp" comes from an iterator over the DSA switch tree - this reduces the complexity from quadratic to linear. Move these helpers from dsa2.c to include/net/dsa.h so that others can use them too. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
8674f8d310 |
net: dsa: assert uniqueness of dsa,member properties
The cross-chip notifiers work by comparing each ds->index against the info->sw_index value from the notifier. The ds->index is retrieved from the device tree dsa,member property. If a single tree cross-chip topology does not declare unique switch IDs, this will result in hard-to-debug issues/voodoo effects such as the cross-chip notifier for one switch port also matching the port with the same number from another switch. Check in dsa_switch_parse_member_of() whether the DSA switch tree contains a DSA switch with the index we're preparing to add, before actually adding it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Oleksij Rempel
|
c916e8e1ea |
net: dsa: dsa_slave_phy_connect(): extend phy's flags with port specific phy flags
The current get_phy_flags() is only processed when we connect to a PHY via a designed phy-handle property via phylink_of_phy_connect(), but if we fallback on the internal MDIO bus created by a switch and take the dsa_slave_phy_connect() path then we would not be processing that flag and using it at PHY connection time. Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
566b18c8b7 |
net: dsa: sja1105: implement TX timestamping for SJA1110
The TX timestamping procedure for SJA1105 is a bit unconventional because the transmit procedure itself is unconventional. Control packets (and therefore PTP as well) are transmitted to a specific port in SJA1105 using "management routes" which must be written over SPI to the switch. These are one-shot rules that match by destination MAC address on traffic coming from the CPU port, and select the precise destination port for that packet. So to transmit a packet from NET_TX softirq context, we actually need to defer to a process context so that we can perform that SPI write before we send the packet. The DSA master dev_queue_xmit() runs in process context, and we poll until the switch confirms it took the TX timestamp, then we annotate the skb clone with that TX timestamp. This is why the sja1105 driver does not need an skb queue for TX timestamping. But the SJA1110 is a bit (not much!) more conventional, and you can request 2-step TX timestamping through the DSA header, as well as give the switch a cookie (timestamp ID) which it will give back to you when it has the timestamp. So now we do need a queue for keeping the skb clones until their TX timestamps become available. The interesting part is that the metadata frames from SJA1105 haven't disappeared completely. On SJA1105 they were used as follow-ups which contained RX timestamps, but on SJA1110 they are actually TX completion packets, which contain a variable (up to 32) array of timestamps. Why an array? Because: - not only is the TX timestamp on the egress port being communicated, but also the RX timestamp on the CPU port. Nice, but we don't care about that, so we ignore it. - because a packet could be multicast to multiple egress ports, each port takes its own timestamp, and the TX completion packet contains the individual timestamps on each port. This is unconventional because switches typically have a timestamping FIFO and raise an interrupt, but this one doesn't. So the tagger needs to detect and parse meta frames, and call into the main switch driver, which pairs the timestamps with the skbs in the TX timestamping queue which are waiting for one. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
4913b8ebf8 |
net: dsa: add support for the SJA1110 native tagging protocol
The SJA1110 has improved a few things compared to SJA1105:
- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.
- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.
- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.
But it also aggravated a few things:
- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.
- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:
* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set
So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:
- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.
So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.
On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.
Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.
On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.
The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).
Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Vladimir Oltean
|
617ef8d937 |
net: dsa: sja1105: make SJA1105_SKB_CB fit a full timestamp
In SJA1105, RX timestamps for packets sent to the CPU are transmitted in separate follow-up packets (metadata frames). These contain partial timestamps (24 or 32 bits) which are kept in SJA1105_SKB_CB(skb)->meta_tstamp. Thankfully, SJA1110 improved that, and the RX timestamps are now transmitted in-band with the actual packet, in the timestamp trailer. The RX timestamps are now full-width 64 bits. Because we process the RX DSA tags in the rcv() method in the tagger, but we would like to preserve the DSA code structure in that we populate the skb timestamp in the port_rxtstamp() call which only happens later, the implication is that we must somehow pass the 64-bit timestamp from the rcv() method all the way to port_rxtstamp(). We can use the skb->cb for that. Rename the meta_tstamp from struct sja1105_skb_cb from "meta_tstamp" to "tstamp", and increase its size to 64 bits. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
233697b3b3 |
net: dsa: tag_8021q: refactor RX VLAN parsing into a dedicated function
The added value of this function is that it can deal with both the case where the VLAN header is in the skb head, as well as in the offload field. This is something I was not able to do using other functions in the network stack. Since both ocelot-8021q and sja1105 need to do the same stuff, let's make it a common service provided by tag_8021q. This is done as refactoring for the new SJA1110 tagger, which partly uses tag_8021q as well (just like SJA1105), and will be the third caller. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Vladimir Oltean
|
baa3ad08de |
net: dsa: tag_sja1105: stop resetting network and transport headers
This makes no sense and is not needed, it is probably a debugging leftover. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> |