When wakeirq is not used/enabled, "no wakeirq for uart0" is output for
all TTY as the log message is generated before the port line is
initialized.
[ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.811700] omap_uart 44e09000.serial: no wakeirq for uart0
[ 0.812379] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[ 1.503622] console [ttyO0] enabled
[ 1.509836] omap_uart 48022000.serial: no wakeirq for uart0
[ 1.516118] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[ 1.527711] omap_uart 48024000.serial: no wakeirq for uart0
[ 1.533881] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[ 1.545324] omap_uart 481a6000.serial: no wakeirq for uart0
[ 1.551410] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3
[ 1.562946] omap_uart 481a8000.serial: no wakeirq for uart0
[ 1.569036] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4
Fix by moving wakeirq initialization, check, and dev_info() call to
after port line initialization and validation.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This
makes it impossible for either the serial core or userspace to
manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fixes for omap-serial.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
index 18c30ca..f43ed2c 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an homogeneous lock system between setting and using the rs485
data of the uart_port.
This patch should not be split into multiple ones in order to avoid
leaving the tree in an unstable state.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Suggested-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error message is not necessary. The driver core code will print all
probe error messages. It also resolves some error codes to proper error
messages. For example -EPROBE_DEFER will only be printed as an info message.
This patch removes the error message as the core prints the same
information.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To determine the correct divisor, we need to know the difference between
the desired baud rate and the actual baud rate. The calculation for this
difference is implemented twice within omap_serial_baud_is_mode16().
Pull out the calculation for easier maintenance.
While at it, remove the CamelCasing from the variable names.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nobody passes a DTR_gpio to this driver, so
this code is not necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
just using helper function to remove some duplicated
code a bit. While at that, also move allocation of
struct uart_omap_port higher in the code so that
we return much earlier in case of no memory.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this way we can remove one pointer declaration.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this will make sure gpio gets freed automatically
when this device is destroyed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
per CodingStyle we should have those braces, no
functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0324a82102.
That commit tried to fix a deadlock problem when using
hci_ldisc, but it turns out the bug was in hci_ldsic
all along where it was calling ->write() from within
->write_wakeup() callback.
The problem is that ->write_wakeup() was called with
port lock held and ->write() tried to grab the same
port lock.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lack of pm_runtime_resume handling for the device state leads into
device wake-up interrupts not working after a while for runtime PM.
Also, serial-omap is confused about the use of device_may_wakeup.
The checks for device_may_wakeup should only be done for suspend and
resume, not for pm_runtime_suspend and pm_runtime_resume. The wake-up
events for PM runtime should always be enabled.
The lack of pm_runtime_resume handling leads into device wake-up
interrupts not working after a while for runtime PM.
Rather than try to patch over the issue of adding complex tests to
the pm_runtime_resume, let's fix the issues properly:
1. Make serial_omap_enable_wakeup deal with all internal PM state
handling so we don't need to test for up->wakeups_enabled elsewhere.
Later on once omap3 boots in device tree only mode we can also
remove the up->wakeups_enabled flag and rely on the wake-up
interrupt enable/disable state alone.
2. Do the device_may_wakeup checks in suspend and resume only,
for runtime PM the wake-up events need to be always enabled.
3. Finally just call serial_omap_enable_wakeup and make sure we
call it also in pm_runtime_resume.
4. Note that we also have to use disable_irq_nosync as serial_omap_irq
calls pm_runtime_get_sync.
Fixes: 2a0b965cfb (serial: omap: Add support for optional wake-up)
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided that the SER_RS485_RX_DURING_TX flag is not set, empty the
RX FIFO to prevent reading back the transmitted data.
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that serial_omap_stop_rx() also disables RDI (Receiver Data Interrupt),
otherwise the interrupt handler will call serial_omap_rdi() to read the new data,
resulting in the transmission being echoed back.
When the half-duplex transmission is complete, in order to reverse the effects of
serial_omap_stop_rx(), we should re-enable:
* the RX interrupts _without_ overwriting up->ier
* the UART_LSR_DR bit of the up->port.read_status_mask
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the gpio is not yet available we better also
defer the probing in the rs485 case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This can cause lots of extra messages at boot time, slowing things down. It is
caused by commit 2a0b965cfb (serial: omap: Add support for optional wake-up)
which was applied for v3.13-rc1.
This patch moves the infomessage to the probe function to display it
only once.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RS-485 is enabled, make the OMAP UART fire THR interrupts when both
TX FIFO and TX shift register are empty instead of polling the
equivalent status bit. This removes the burst of interrupt requests
seen at every end of transmission.
Also: the comment said that the TX FIFO trigger level was set at 16
characters when it's 32 in reality.
Signed-off-by: Philippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent pinctrl-single changes, omaps can treat
wake-up events from deeper idle states as interrupts.
There's a separate "io chain" controller on most omaps
that stays enabled when the device hits off-idle and the
regular interrupt controller is powered off.
Let's add support for the optional second interrupt for
wake-up events. And then serial-omap can manage the
wake-up interrupt from it's runtime PM calls to avoid
spurious interrupts during runtime.
Note that the wake interrupt is board specific as it
uses the UART RX pin, and for omap3, there are six pin
options for UART3 RX pin.
Also Note that the legacy platform based booting handles
the wake-ups in the legacy mux driver and does not need to
pass the wake-up interrupt to the driver.
And finally, to pass the wake-up interrupt in the dts file,
either interrupt-map or the pending interrupts-extended
property needs to be passed. It's probably best to use
interrupts-extended when it's available.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
OMAP serial driver is done through other runpaths these days.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make Mode16 more preferred than Mode13, to match TRM baudrates table.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c441508421.
Kevin writes:
Hmm, another OMAP serial patch that wasn't Cc'd to linux-omap
where OMAP users might have seen it. :(
I just bisected a strange problem in linux-next on OMAP3 down to
this patch. Reverting it fixes the problem.
On OMAP3530 Beagle and Overo, after boot, doing a 'cat
/proc/cpuinfo' was not returning to a prompt, suggesting
something strange with the FIFO. Hitting return gets me back to
a prompt.
Greg, this one should also be dropped from tty-next until it can
be further investgated and the problem solved.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Dmitry Fink <finik@ti.com>
Cc: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 908fd7e566.
Kevin writes:
Greg, without a better justification in the changelog, I think
this patch should be dropped from tty-next.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Ruchika Kharwar <ruchika@ti.com>
Cc: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent patch to add RS485 contained a bug whereby the IER
interrupt was cleared down incorrectly.
This patch fixes the problem.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds RS485 support to the OMAP serial driver, as
defined in:-
Documentation/devicetree/bindings/serial/rs485.txt
When a UART transmitter is connected to (eg) a RS485 driver, it is
necessary to turn the driver on/off as quickly as possible. This is
best achieved in the serial driver itself (rather than in userspace
where the latency can be quite large).
This patch allows a GPIO pin to be defined (via DT) that controls
the enabling of the driver at the start of a message, and disables
the driver when the message has been completed.
When RS485 is disabled, the RTS pin is set to on.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If earlyprintk is enabled and current UART is console port the platform
code can mark it as RPM_ACTIVE to sync real IP state with PM Runtime and
avoid resuming of already active device, but now, driver initialization
will be performed in the wrong way:
pm_runtime_enable(&pdev->dev);
<-- PM runtime alowed (device state RPM_ACTIVE)
if (omap_up_info->autosuspend_timeout == 0)
omap_up_info->autosuspend_timeout = -1;
device_init_wakeup(up->dev, true);
pm_runtime_use_autosuspend(&pdev->dev);
<-- update_autosuspend() will be called and it will disable device
(device state RPM_SUSPENDED)
pm_runtime_set_autosuspend_delay(&pdev->dev,
omap_up_info->autosuspend_timeout);
<-- update_autosuspend() will be called which will re-enable device
(device state RPM_ACTIVE), because autosuspend_timeout < 0
pm_runtime_irq_safe(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
<-- will do nothing
Such behavior isn't expected by OMAP serial drivers and causes
unpredictable calls of serial_omap_runtime_suspend() and
serial_omap_runtime_resume().
Hence, fix it by allowing PM runtime only after all its parameters are
configured.
CC: Tony Lindgren <tony@atomide.com>
CC: Rajendra Nayak <rnayak@ti.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise serial driver would crash accessing platform_data that was
not initialized in functions like:
serial_omap_pm(...)
...
if (!state && pdata->enable_wakeup)
^^^^^^^
...
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revision register is a 32 bit register. The serial_in() function reads
only the lower 16 bits of the register. This leads to an incorrect computation
of the Module revision.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
[oleksandr.savchenko@ti.com: add some whitespaces]
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current logic results in interrupt storm since the fifo
is constantly below the threshold level. Change the logic
to fill all the available spaces in the fifo as long as
we have data to minimize the possibilty of underflow and
elimiate excessive interrupts.
Signed-off-by: Dmitry Fink <finik@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wer has TX wakeup bit available enable the same
by populating the necessary tx wakeup flag for the
applicable module ip blocks and use the same
while configuaring wer reg.
Also wer is not context restored, restore wer when
context is lost.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(for drivers/tty changes)
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the runtime_suspend function pdata is not being used, and
also blocks the function in device tree based booting. Fix it
by removing the unused pdata from the runtime_suspend function.
Further, context loss count is not being passed in pdata, so
let's just reinitialize the port every time for those case.
This can be further optimized later on for the device tree
case by adding detection for the hardware state and possibly
by adding a driver specific autosuspend timeout.
And doing this, we can then make the related dev_err into a
dev_dbg message instead of an error.
In order for the wake-up events to work, we also need to set
autosuspend_timeout to -1 if 0, and also device_init_wakeup()
as that's not being done by the platform init code for the
device tree case.
Note that this does not affect legacy booting, and in fact
might make it work for the cases where the context loss info
is not being passed in pdata.
Thanks to Kevin Hilman <khilman@linaro.org> for debugging
and suggesting fixes for the autosuspend_timeout and
device_init_wakeup() related initializiation.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dereference to 'up' should be moved below the NULL test.
Introduced by commit ddd85e225c
(serial: omap: prevent runtime PM for "no_console_suspend")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent bug fix in 3.10, ddd85e225c "serial: omap: prevent runtime PM for
"no_console_suspend"", introduced a regression from an obvious typo:
drivers/tty/serial/omap-serial.c:1677:14: error: 'serial_omap_complete'
undeclared here (not in a function)
This changes the incorrectly added macro to the one that we need instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
