Not all platforms have all of the four currently supported wakeup
interrupts so use the optional irq helpers when looking up interrupts to
avoid printing error messages when an optional interrupt is not found:
dwc3-qcom a6f8800.usb: error -ENXIO: IRQ hs_phy_irq not found
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220713131340.29401-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the programming guide, it is recommended to
perform a GCTL_CORE_SOFTRESET only when switching the mode
from device to host or host to device. However, it is found
that during bootup when __dwc3_set_mode() is called for the
first time, GCTL_CORESOFTRESET is done with suspendable bit(BIT 17)
of DWC3_GUSB3PIPECTL set. This some times leads to issues
like controller going into bad state and controller registers
reading value zero. Until GCTL_CORESOFTRESET is done and
run/stop bit is set core initialization is not complete.
Setting suspendable bit of DWC3_GUSB3PIPECTL and then
performing GCTL_CORESOFTRESET is therefore not recommended.
Avoid this by only performing the reset if current_dr_role is set,
that is, when doing subsequent role switching.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Signed-off-by: Rohith Kollalsi <quic_rkollals@quicinc.com>
Link: https://lore.kernel.org/r/20220714045625.20377-1-quic_rkollals@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a 3 stage SETUP transfer, if the host sends another SETUP token
before completing the status phase, it signifies that the host has aborted
the current control transfer. Currently, if a setup_packet_pending is
received, there are no subsequent calls to dwc3_ep0_out_start() to fetch
the new SETUP packet. This leads to a stall on EP0, as host does not
expect another STATUS phase as it has aborted the current transfer.
Fix this issue by explicitly stalling and restarting EP0, as well as
resetting the trb_enqueue indexes. (without this, there is a chance the
SETUP TRB is set up on trb_endqueue == 1)
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220712014403.2977-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For High-Speed Transfers the prepare_one_trb function is calculating the
multiplier setting for the trb based on the length parameter of the trb
currently prepared. This assumption is wrong. For trbs with a sg list,
the length of the actual request has to be taken instead.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function __dwc3_prepare_one_trb has many parameters. Since it is
only used in dwc3_prepare_one_trb there is no point in keeping the
function. We merge both functions and get rid of the big list of
parameters.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clk get by devm_clk_get() will be released in devres_release_all(),
so there is no need explicitly call clk_put(), or it will cause UAF.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220629094635.3116961-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3_EVENT_PENDING flag is used to protect against invalid call to
top-half interrupt handler, which can occur when there's a delay in
software detection of the interrupt line deassertion.
However, the clearing of this flag was done prior to unmasking the
interrupt line, creating opportunity where the top-half handler can
come. This breaks the serialization and creates a race between the
top-half and bottom-half handler, resulting in losing synchronization
between the controller and the driver when processing events.
To fix this, make sure the clearing of the DWC3_EVENT_PENDING is done at
the end of the bottom-half handler.
Fixes: d325a1de49 ("usb: dwc3: gadget: Prevent losing events in event cache")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8670aaf1cf52e7d1e6df2a827af2d77263b93b75.1656380429.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The multiplier parameter of dwc3_gadget_calc_tx_fifo_size() was
not documented:
drivers/usb/dwc3/gadget.c:675: warning: Function parameter or member 'mult' not described in 'dwc3_gadget_calc_tx_fifo_size'
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/bd599a18cea45c57d91c69d3e30d8b1e8ea69dd1.1656409369.git.mchehab@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is wakeup capable, keep the power domain always ON so that
wakeup from system suspend can be supported. Otherwise, keep the
power domain ON only during runtime suspend to support wakeup from
runtime suspend.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-6-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-5-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check wakeup-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.
If the dwc3 is wakeup capable, don't power down the USB PHY(s).
The glue drivers are expected to take care of configuring the
additional wakeup settings if needed based on the dwc3 wakeup
capability status. In some SOC designs, powering off the PHY is
resulting in higher leakage, so this patch save power on such boards.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-3-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys IP DWC_usb32 and DWC_usb31 version 1.90a and above deprecated
GCTL.CORESOFTRESET. The DRD mode switching flow is updated to remove the
GCTL soft reset. Add version checks to prevent using deprecated setting
in mode switching flow.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9df529fde6e55f5508321b6bc26e92848044ef2b.1655338967.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge v5.19-rc3 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57303488cd ("usb: dwc3: adapt dwc3 core to use Generic PHY
Framework") added if statements that check 'ret == -ENOSYS || ret ==
-ENODEV', but the function phy_get() which is called by devm_phy_get()
returns the phy driver or -ENODEV if the phy driver was not found. So,
remove the check of -ENOSYS in the if statements.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/HK0PR01MB2801E19D4FE569545BB7592DF8A19@HK0PR01MB2801.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC(e.g NXP imx8MQ) may have a wrong default power down scale
setting so need init it to be the correct value, the power down
scale setting description in DWC3 databook:
Power Down Scale (PwrDnScale)
The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source to
a small part of the USB3 core that operates when the SS PHY is in its
lowest power (P3) state, and therefore does not provide a clock.
The Power Down Scale field specifies how many suspend_clk periods fit
into a 16 kHz clock period. When performing the division, round up the
remainder.
For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz Suspend
clock,
Power Down Scale = 25000 kHz/16 kHz = 13'd1563 (rounder up)
So use the suspend clock rate to calculate it.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1654568404-3461-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today's linux-next merge of the extcon tree got a conflict in:
drivers/usb/dwc3/drd.c
between commit:
0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
from the usb tree and commit:
88490c7f43c4 ("extcon: Fix extcon_get_extcon_dev() error handling")
from the extcon tree.
I fixed it up (the former moved the code modified by the latter, so I
used the former version of this files and added the following merge fix
patch) and can carry the fix as necessary.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220426152739.62f6836e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 582ab24e09 ("usb: dwc3: pci: Set "linux,phy_charger_detect"
property on some Bay Trail boards") added a new swnode similar to the
existing ones for boards where the PHY handles charger detection.
Unfortunately, the "linux,sysdev_is_parent" property got lost in the
merge conflict resolution of commit ca9400ef7f ("Merge 5.17-rc6 into
usb-next"). Now dwc3_pci_intel_phy_charger_detect_properties is the
only swnode in dwc3-pci that is missing "linux,sysdev_is_parent".
It does not seem to cause any obvious functional issues, but it's
certainly unintended so restore the line to make the properties
consistent again.
Fixes: ca9400ef7f ("Merge 5.17-rc6 into usb-next")
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220528170913.9240-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic to assign the max packet limit for IN endpoints attempts
to take the default HW value and apply the optimal endpoint settings based
on it. However, if the default value reports a TxFIFO size large enough
for only one max packet, it will divide the value and assign a smaller ep
max packet limit.
For example, if the default TxFIFO size fits 1024B, current logic will
assign 1024/3 = 341B to ep max packet size. If function drivers attempt to
request for an endpoint with a wMaxPacketSize of 1024B (SS BULK max packet
size) then it will fail, as the gadget is unable to find an endpoint which
can fit the requested size.
Functionally, if the TxFIFO has enough space to fit one max packet, it will
be sufficient, at least when initializing the endpoints.
Fixes: d94ea53198 ("usb: dwc3: gadget: Properly set maxpacket limit")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220523213948.22142-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 controller soft reset is important operation for USB functionality.
In case when it fails, currently there is no failure log. Hence add
error log when core soft reset failed.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1652897572-14461-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes: 2628844812 ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1651693001-29891-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller hasn't DMA'ed the Setup data from its fifo, it won't
process the End Transfer command. Polling for the command completion may
block the driver from servicing the Setup phase and cause a timeout.
Previously we only check and delay issuing End Transfer in the case of
endpoint dequeue. Let's do that for all End Transfer scenarios.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2fcf3b5d90068d549589a57a27a79f76c6769b04.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver shouldn't be able to issue End Transfer to the control
endpoint at anytime. Typically we should only do so in error cases such
as invalid/unexpected direction of Data Phase as described in the
control transfer flow of the programming guide. It _may_ end started
data phase during controller deinitialization from soft disconnect or
driver removal. However, that should not happen because the driver
should be maintained in EP0_SETUP_PHASE during driver tear-down. On
soft-connect, the controller should be reset from a soft-reset and there
should be no issue starting the control endpoint.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3c6643678863a26702e4115e9e19d7d94a30d49c.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we can't guarantee that the host won't send new Setup packet
before going through the device-initiated disconnect, don't prepare
beyond the Setup stage and keep the device in EP0_SETUP_PHASE. This
ensures that the device-initated disconnect sequence can go through
gracefully. Note that the controller won't service the End Transfer
command if it can't DMA out the Setup packet.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6bacec56ecabb2c6e49a09cedfcac281fdc97de0.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB GPIO based reset for dwc3-xilinx driver. The PHY
needs to be reset after the completion of phy initialization. As part
of the reset, check for gpio-reset binding before toggling the pin.
This feature is advantageous when the user toggle GPIO to trigger the
ULPI-PHY reset.
Delay of milliseconds is added in between low and high to meet the setup
and hold time requirement of the reset. The reset-gpio error handling is
added for error notification.
Some GPIO controllers must be accessed using message-based buses, like
I2C or SPI, to address this problem, updates GPIO access with sleep API.
This reset is specific to the zynqMp.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220504075309.6244-3-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed. The sysdev pointer is now used when
assigning the ACPI companions to the xHCI ports and USB
devices.
Assigning the ACPI companion here resulted in the
fwnode->secondary pointer to be replaced also for the parent
dwc3 device since the primary fwnode (the ACPI companion)
was shared. That was unintentional and it created potential
side effects like resource leaks.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 8eed00b237 ("usb: dwc3: pci: Runtime resume child device from wq")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062652.10575-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list]
->spin_unlock
Fixes: d4f1afe5e8 ("usb: dwc3: gadget: move requests to cancelled_list")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414183521.23451-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_ep_clear_halt() API can be called from the function driver, and
translates to dwc3_gadget_ep_set_halt(). This routine is shared with when
the host issues a clear feature ENDPOINT_HALT, and is differentiated by the
protocol argument. If the following sequence occurs, there can be a
situation where the delayed_status flag is improperly cleared for the wrong
SETUP transaction:
1. Vendor specific control transfer returns USB_GADGET_DELAYED_STATUS.
2. DWC3 gadget sets dwc->delayed_status to '1'.
3. Another function driver issues a usb_ep_clear_halt() call.
4. DWC3 gadget issues dwc3_stop_active_transfer() and sets
DWC3_EP_PENDING_CLEAR_STALL.
5. EP command complete interrupt triggers for the end transfer, and
dwc3_ep0_send_delayed_status() is allowed to run, as delayed_status
is '1' due to step#1.
6. STATUS phase is sent, and delayed_status is cleared.
7. Vendor specific control transfer is finished being handled, and issues
usb_composite_setup_continue(). This results in queuing of a data
phase.
Cache the protocol flag so that DWC3 gadget is aware of when the clear halt
is due to a SETUP request from the host versus when it is sourced from a
function driver. This allows for the EP command complete interrupt to know
if it needs to issue a delayed status phase.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414073902.21960-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.
Fixes: f59dcab176 ("usb: dwc3: core: improve reset sequence")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6aecbd78328f102003d40ccf18ceeebd411d3703.1650594792.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the extcon device exists, get the mode from the extcon device. If
the controller is DRD and the driver is unable to determine the mode,
only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/20220403164907.662860-1-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve performance of isoc transfers in superspeed by increasing the
number of possible endpoints available, matching that of what was
configured for bulk transfers.
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220420183338.445622-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two kerneldoc comments in gadget.c have excess function parameter description or wrong
prototype name and one kerneldoc comment in core.c has an excess function parameter
description, resulting in these three doc-build warnings:
1. ./drivers/usb/dwc3/gadget.c:675: warning: Excess function parameter
'nfifos' description in 'dwc3_gadget_calc_tx_fifo_size'
2. ./drivers/usb/dwc3/gadget.c:700: warning: expecting prototype for
dwc3_gadget_clear_tx_fifo_size(). Prototype was for dwc3_gadget_clear_tx_fifos()
instead
3. ./drivers/usb/dwc3/core.c:347: warning: Excess function parameter 'ref_clk_per'
description in 'dwc3_ref_clk_period'
Fix the warnings by correcting the prototype name and removing excess parameter descriptions.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/SI2PR01MB392995043CACD80884A13764F81C9@SI2PR01MB3929.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a137997 ("usb: dwc3: Registering a role switch in the DRD code.")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
Fixes: 938a5ad1d3 ("usb: dwc3: Check for ESS TX/RX threshold config")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cccfce990b11b730b0dae42f9d217dc6fb988c90.1649727139.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
