The Intel IOMMU driver will put devices into a static identity
mapped domain during boot if the kernel parameter "iommu=pt" is
used. That means the IOMMU hardware will translate a DMA address
into the same memory address.
Unfortunately, hot-added devices are not subject to this. That
results in some devices not working properly after hot added. A
quick way to reproduce this issue is to boot a system with
iommu=pt
and, remove then readd the pci device with
echo 1 > /sys/bus/pci/devices/[pci_source_id]/remove
echo 1 > /sys/bus/pci/rescan
You will find the identity mapped domain was replaced with a
normal domain.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Reported-by: Jis Ben <jisben@google.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: James Dong <xmdong@google.com>
Fixes: 99dcadede4 ('intel-iommu: Support PCIe hot-plug')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
As per Intel vt-d specification, Rev 3.0 (section 7.5.1.1, title "Page
Request Descriptor"), Intel IOMMU page request descriptor only uses
bits[63:12] of the page address. Hence Intel IOMMU driver would only
permit devices that advertise they would only send Page Aligned Requests
to participate in ATS service.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In Intel IOMMU, if the Page Request Queue (PRQ) is full, it will
automatically respond to the device with a success message as a keep
alive. And when sending the success message, IOMMU will include PASID in
the Response Message when the Page Request has a PASID in Request
Message and it does not check against the PRG Response PASID requirement
of the device before sending the response. Also, if the device receives
the PRG response with PASID when its not expecting it the device behavior
is undefined. So if PASID is enabled in the device, enable PRI only if
device expects PASID in PRG Response Message.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When a device has multiple aliases that all are from the same bus,
we program the IRTE to accept requests from any matching device on the
bus.
This is so NTB devices which can have requests from multiple bus-devfns
can pass MSI interrupts through across the bridge.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The current code uses set_irte_sid() with SVT_VERIFY_BUS and PCI_DEVID
to set the SID value. However, this is very confusing because, with
SVT_VERIFY_BUS, the SID value is not a PCI devfn address, but the start
and end bus numbers to match against.
According to the Intel Virtualization Technology for Directed I/O
Architecture Specification, Rev. 3.0, page 9-36:
The most significant 8-bits of the SID field contains the Startbus#,
and the least significant 8-bits of the SID field contains the Endbus#.
Interrupt requests that reference this IRTE must have a requester-id
whose bus# (most significant 8-bits of requester-id) has a value equal
to or within the Startbus# to Endbus# range.
So to make this more clear, introduce a new set_irte_verify_bus() that
explicitly takes a start bus and end bus so that we can stop abusing
the PCI_DEVID macro.
This helper function will be called a second time in an subsequent patch.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The "Domain 0 is reserved, so dont process it" comment suggests that a NULL
pointer corresponds to domain 0. I don't think that's true, and in any
case, every caller supplies a non-NULL domain pointer that has already been
dereferenced, so the test is unnecessary.
Remove the test for a null "domain" pointer. No functional change
intended.
This null pointer check was added by 5e98c4b1d6 ("Allocation and free
functions of virtual machine domain").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
domain_remove_dev_info() takes a struct dmar_domain * argument, but doesn't
use it. Remove it. No functional change intended.
The last use of this argument was removed by 127c761598 ("iommu/vt-d:
Pass device_domain_info to __dmar_remove_one_dev_info").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A local variable initialization is a hint that the variable will be used in
an unusual way. If the initialization is unnecessary, that hint becomes a
distraction.
Remove unnecessary initializations. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use dev_printk() when possible so the IOMMU messages are more consistent
with other messages related to the device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The change_pte() interface is tailored for PFN updates, while the
other notifier invalidate_range() should be enough for Intel IOMMU
cache flushing. Actually we've done similar thing for AMD IOMMU
already in 8301da53fb ("iommu/amd: Remove change_pte mmu_notifier
call-back", 2014-07-30) but the Intel IOMMU driver still have it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently the Intel IOMMU uses the default dma_[un]map_resource()
implementations does nothing and simply returns the physical address
unmodified.
However, this doesn't create the IOVA entries necessary for addresses
mapped this way to work when the IOMMU is enabled. Thus, when the
IOMMU is enabled, drivers relying on dma_map_resource() will trigger
DMAR errors. We see this when running ntb_transport with the IOMMU
enabled, DMA, and switchtec hardware.
The implementation for intel_map_resource() is nearly identical to
intel_map_page(), we just have to re-create __intel_map_single().
dma_unmap_resource() uses intel_unmap_page() directly as the
functions are identical.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
VT-d Rev3.0 has made a few changes to the page request interface,
1. widened PRQ descriptor from 128 bits to 256 bits;
2. removed streaming response type;
3. introduced private data that requires page response even the
request is not last request in group (LPIG).
This is a supplement to commit 1c4f88b7f1 ("iommu/vt-d: Shared
virtual address in scalable mode") and makes the svm code compliant
with VT-d Rev3.0.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
This check needs to be there and got lost at some point
during development. Add it again.
Fixes: 641fb0efbf ('iommu/of: Don't call iommu_ops->add_device directly')
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Remove the iommu_ prefix from the function and a few other
static data structures so that the iommu_release_device name
can be re-used in iommu core code.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use Use device_iommu_mapped() to check if the device is
already mapped by an IOMMU.
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the new helpers dev_iommu_fwspec_get()/set() to access
the dev->iommu_fwspec pointer. This makes it easier to move
that pointer later into another struct.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
These wrappers will be used to easily change the location of
the field later when all users are converted.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This reverts commit 82db33dc5e.
After the commit 29859aeb8a ("iommu/io-pgtable-arm-v7s: Abort
allocation when table address overflows the PTE"), v7s will return fail
if the page table allocation isn't expected. this PHYS_OFFSET check
is unnecessary now.
And this check may lead to fail. For example, If CONFIG_RANDOMIZE_BASE
is enabled, the "memstart_addr" will be updated randomly, then the
PHYS_OFFSET may be random.
Reported-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Avoid expensive indirect calls in the fast path DMA mapping
operations by directly calling the dma_direct_* ops if we are using
the directly mapped DMA operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Deferred invalidation is an ECS specific feature. It will not be
supported when IOMMU works in scalable mode. As we deprecated the
ECS support, remove deferred invalidation and cleanup the code.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch enables the current SVA (Shared Virtual Address)
implementation to work in the scalable mode.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds an interface to setup the PASID entries for first
level page table translation.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch enables the translation for requests without PASID in
the scalable mode by setting up the root and context entries.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
So that the pasid related info, such as the pasid table and the
maximum of pasid could be used during setting up scalable mode
context.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
when the scalable mode is enabled, there is no second level
page translation pointer in the context entry any more (for
DMA request without PASID). Instead, a new RID2PASID field
is introduced in the context entry. Software can choose any
PASID value to set RID2PASID and then setup the translation
in the corresponding PASID entry. Upon receiving a DMA request
without PASID, hardware will firstly look at this RID2PASID
field and then treat this request as a request with a pasid
value specified in RID2PASID field.
Though software is allowed to use any PASID for the RID2PASID,
we will always use the PASID 0 as a sort of design decision.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds the interfaces to setup or tear down the structures
for second level page table translations. This includes types
of second level only translation and pass through.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Vt-d spec rev3.0 (section 6.2.3.1) requires that each pasid
entry for first-level or pass-through translation should be
programmed with a domain id different from those used for
second-level or nested translation. It is recommended that
software could use a same domain id for all first-only and
pass-through translations.
This reserves a domain id for first-level and pass-through
translations.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Intel vt-d spec rev3.0 requires software to use 256-bit
descriptors in invalidation queue. As the spec reads in
section 6.5.2:
Remapping hardware supporting Scalable Mode Translations
(ECAP_REG.SMTS=1) allow software to additionally program
the width of the descriptors (128-bits or 256-bits) that
will be written into the Queue. Software should setup the
Invalidation Queue for 256-bit descriptors before progra-
mming remapping hardware for scalable-mode translation as
128-bit descriptors are treated as invalid descriptors
(see Table 21 in Section 6.5.2.10) in scalable-mode.
This patch adds 256-bit invalidation descriptor support
if the hardware presents scalable mode capability.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
So that they could also be used in other source files.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In scalable mode, pasid structure is a two level table with
a pasid directory table and a pasid table. Any pasid entry
can be identified by a pasid value in below way.
1
9 6 5 0
.-----------------------.-------.
| PASID | |
'-----------------------'-------' .-------------.
| | | |
| | | |
| | | |
| .-----------. | .-------------.
| | | |----->| PASID Entry |
| | | | '-------------'
| | | |Plus | |
| .-----------. | | |
|---->| DIR Entry |-------->| |
| '-----------' '-------------'
.---------. |Plus | |
| Context | | | |
| Entry |------->| |
'---------' '-----------'
This changes the pasid table APIs to support scalable mode
PASID directory and PASID table. It also adds a helper to
get the PASID table entry according to the pasid value.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Intel vt-d spec rev3.0 introduces a new translation
mode called scalable mode, which enables PASID-granular
translations for first level, second level, nested and
pass-through modes. At the same time, the previous
Extended Context (ECS) mode is deprecated (no production
ever implements ECS).
This patch adds enumeration for Scalable Mode and removes
the deprecated ECS enumeration. It provides a boot time
option to disable scalable mode even hardware claims to
support it.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Change function __iommu_dma_alloc_pages() to allocate pages for DMA from
respective device NUMA node. The ternary operator which would be for
alloc_pages_node() is tidied along with this.
The motivation for this change is to have a policy for page allocation
consistent with direct DMA mapping, which attempts to allocate pages local
to the device, as mentioned in [1].
In addition, for certain workloads it has been observed a marginal
performance improvement. The patch caused an observation of 0.9% average
throughput improvement for running tcrypt with HiSilicon crypto engine.
We also include a modification to use kvzalloc() for kzalloc()/vzalloc()
combination.
[1] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1692998.html
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
[JPG: Added kvzalloc(), drop pages ** being device local, remove ternary operator, update message]
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
qcom,smmu-v2 is an arm,smmu-v2 implementation with specific
clock and power requirements.
On msm8996, multiple cores, viz. mdss, video, etc. use this
smmu. On sdm845, this smmu is used with gpu.
Add bindings for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Finally add the device link between the master device and
smmu, so that the smmu gets runtime enabled/disabled only when the
master needs it. This is done from add_device callback which gets
called once when the master is added to the smmu.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enable pm-runtime on devices that implement a pm domain. Then,
add pm runtime hooks to several iommu_ops to power cycle the
smmu device for explicit TLB invalidation requests, and
register space accesses, etc.
We need these hooks when the smmu, linked to its master through
device links, has to be powered-up without the master device
being in context.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
[vivek: Cleanup pm runtime calls]
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The smmu needs to be functional only when the respective
master's using it are active. The device_link feature
helps to track such functional dependencies, so that the
iommu gets powered when the master device enables itself
using pm_runtime. So by adapting the smmu driver for
runtime pm, above said dependency can be addressed.
This patch adds the pm runtime/sleep callbacks to the
driver and the corresponding bulk clock handling for all
the clocks needed by smmu.
Also, while we enable the runtime pm, add a pm sleep suspend
callback that pushes devices to low power state by turning
the clocks off in a system sleep.
Add corresponding clock enable path in resume callback as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
[Thor: Rework to get clocks from device tree]
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
[vivek: rework for clock and pm ops]
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
After removing an entry from a queue (e.g. reading an event in
arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer
pointer to free the queue slot back to the SMMU. A memory barrier is
required here so that all reads targetting the queue entry have
completed before the consumer pointer is updated.
The implementation of queue_inc_cons() relies on a writel() to complete
the previous reads, but this is incorrect because writel() is only
guaranteed to complete prior writes. This patch replaces the call to
writel() with an mb(); writel_relaxed() sequence, which gives us the
read->write ordering which we require.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The GITS_TRANSLATER MMIO doorbell register in the ITS hardware is
architected to be 4 bytes in size, yet on hi1620 and earlier, Hisilicon
have allocated the adjacent 4 bytes to carry some IMPDEF sideband
information which results in an 8-byte MSI payload being delivered when
signalling an interrupt:
MSIAddr:
|----4bytes----|----4bytes----|
| MSIData | IMPDEF |
This poses no problem for the ITS hardware because the adjacent 4 bytes
are reserved in the memory map. However, when delivering MSIs to memory,
as we do in the SMMUv3 driver for signalling the completion of a SYNC
command, the extended payload will corrupt the 4 bytes adjacent to the
"sync_count" member in struct arm_smmu_device. Fortunately, the current
layout allocates these bytes to padding, but this is fragile and we
should make this explicit.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[will: Rewrote commit message and comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
