When turning this from inline to an exported function I was a bit
over-eager and made it GPL only. This prevents the use of pretty much
all non-GPL PCI driver which is a bit over the top. Let's bring it
back in line with other architecture.
Fixes: 817820b022 ("powerpc/iommu: Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Or Gerlitz says:
====================
Mellanox mlx4 driver fixes for 4.3-rc7
Jack's fix is for a regression introduced in 4.3-rc1
Carol's fix addresses an issue which exists for while and
turns to beat us hard on PPC, please queue for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not set the ins_vlan field to zero when no vlan id is present in the packet.
Since WQEs in the TX ring are not zeroed out between uses, this oversight
could result in having vlan flags present in the WQE ctrl segment when no
vlan is preset.
Fixes: e38af4faf0 ('net/mlx4_en: Add support for hardware accelerated 802.1ad vlan')
Reported-by: Gideon Naim <gideonn@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2751c9882b ("vhost: cross-endian
support for legacy devices") introduced a minor regression: even with
cross-endian disabled, and even on LE host, vhost_is_little_endian is
checking is_le flag so there's always a branch.
To fix, simply check virtio_legacy_is_little_endian first.
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define aarch64 specific registers for building bpf samples correctly.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Either of pskb_pull() or pskb_trim() may fail under low memory conditions.
If rds_tcp_data_recv() ignores such failures, the application will
receive corrupted data because the skb has not been correctly
carved to the RDS datagram size.
Avoid this by handling pskb_pull/pskb_trim failure in the same
manner as the skb_clone failure: bail out of rds_tcp_data_recv(), and
retry via the deferred call to rds_send_worker() that gets set up on
ENOMEM from rds_tcp_read_sock()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcedeth currently uses disable_irq_lockdep and enable_irq_lockdep, which in
some configurations simply calls local_irq_disable. This causes errant warnings
in the netpoll path as in netpoll_send_skb_on_dev, where we disable irqs using
local_irq_save, leading to the following warning:
WARNING: at net/core/netpoll.c:352 netpoll_send_skb_on_dev+0x243/0x250() (Not
tainted)
Hardware name:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll
(nv_start_xmit_optimized+0x0/0x860 [forcedeth])
Modules linked in: netconsole(+) configfs ipv6 iptable_filter ip_tables ppdev
parport_pc parport sg microcode serio_raw edac_core edac_mce_amd k8temp
snd_hda_codec_realtek snd_hda_codec_generic forcedeth snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore
snd_page_alloc i2c_nforce2 i2c_core shpchp ext4 jbd2 mbcache sr_mod cdrom sd_mod
crc_t10dif pata_amd ata_generic pata_acpi sata_nv dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 1940, comm: modprobe Not tainted 2.6.32-573.7.1.el6.x86_64.debug #1
Call Trace:
[<ffffffff8107bbc1>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107bcc6>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffffa00fe5b0>] ? nv_start_xmit_optimized+0x0/0x860 [forcedeth]
[<ffffffff814b3593>] ? netpoll_send_skb_on_dev+0x243/0x250
[<ffffffff814b37c9>] ? netpoll_send_udp+0x229/0x270
[<ffffffffa02e3299>] ? write_msg+0x39/0x110 [netconsole]
[<ffffffffa02e331b>] ? write_msg+0xbb/0x110 [netconsole]
[<ffffffff8107bd55>] ? __call_console_drivers+0x75/0x90
[<ffffffff8107bdba>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107c445>] ? release_console_sem+0xe5/0x250
[<ffffffff8107d200>] ? register_console+0x190/0x3e0
[<ffffffffa02e71a6>] ? init_netconsole+0x1a6/0x216 [netconsole]
[<ffffffffa02e7000>] ? init_netconsole+0x0/0x216 [netconsole]
[<ffffffff810020d0>] ? do_one_initcall+0xc0/0x280
[<ffffffff810d4933>] ? sys_init_module+0xe3/0x260
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
---[ end trace f349c7af88e6a6d5 ]---
console [netcon0] enabled
netconsole: network logging started
Fix it by modifying the forcedeth code to use
disable_irq_nosync_lockdep_irqsavedisable_irq_nosync_lockdep_irqsave instead,
which saves and restores irq state properly. This also saves us a little code
in the process
Tested by the reporter, with successful restuls
Patch applies to the head of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_ct_frag6_gather() makes a clone of each skb passed to it, and if the
reassembly is successful, expects the caller to free all of the original
skbs using nf_ct_frag6_consume_orig(). This call was previously missing,
meaning that the original fragments were never freed (with the exception
of the last fragment to arrive).
Fix this by ensuring that all original fragments except for the last
fragment are freed via nf_ct_frag6_consume_orig(). The last fragment
will be morphed into the head, so it must not be freed yet. Furthermore,
retain the ->next pointer for the head after skb_morph().
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in openvswitch to fix an skb leak in the next patch.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ip_defrag() returns an error other than -EINPROGRESS, then the skb is
freed. When handle_fragments() passes this back up to
do_execute_actions(), it will be freed again. Prevent this double free
by never freeing the skb in do_execute_actions() for errors returned by
ovs_ct_execute. Always free it in ovs_ct_execute() error paths instead.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were computing the child index in cases where the key value we were
looking for was actually less than the base key of the tnode. As a result
we were getting incorrect index values that would cause us to skip over
some children.
To fix this I have added a test that will force us to use child index 0 if
the key we are looking for is less than the key of the current tnode.
Fixes: 8be33e955c ("fib_trie: Fib walk rcu should take a tnode and key instead of a trie and a leaf")
Reported-by: Brian Rak <brak@gameservers.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit b49a087("block: remove split code in
blkdev_issue_{discard,write_same}"), discard_granularity and alignment
checks were removed. Ideally, with bio late splitting, the upper layers
shouldn't need to depend on device's limits.
Christoph reported a discard regression on the HGST Ultrastar SN100 NVMe
device when mkfs.xfs. We have not found the root cause yet.
This patch re-adds discard_granularity and alignment checks by reverting
the related changes in commit b49a087. The good thing is now we can
remove the 2G discard size cap and just use UINT_MAX to avoid bi_size
overflow.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull ARM fixes from Russell King:
"Two fixes for ARM and one for clkdev:
- Fix another build issue with vdsomunge on non-glibc systems
- Fix a randconfig build error caused by an invalid configuration
- Fix a clkdev problem causing the Nokia n700 to no longer boot"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clkdev: fix clk_add_alias() with a NULL alias device name
ARM: 8445/1: fix vdsomunge not to depend on glibc specific byteswap.h
ARM: make RiscPC depend on MMU
Pull blkcg fix from Jens Axboe:
"One final fix that should go into 4.3. It's a simple 2x1 liner,
fixing a blkcg accounting issue. It was using the wrong bio member to
look at the sync and write bits..."
* 'for-linus' of git://git.kernel.dk/linux-block:
blkcg: fix incorrect read/write sync/async stat accounting
Pull crypto fix from Herbert Xu:
"This fixes a problem in the Crypto API that may cause spurious errors
when signals are received by the process that made the orignal system
call into the kernel"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Only abort operations on fatal signal
someone finally caught it thanks to Peter Z's additional checks.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8AgP
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module preemption fix from Rusty Russell:
"Turns out we should have always been disabling preemption here;
someone finally caught it thanks to Peter Z's additional checks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: Fix locking in symbol_put_addr()
Recently 'perf <tool> -h' was made aware of arguments and would show
just the help for the arguments specified, but that required a strict
form, i.e.:
$ perf -h --tui
worked, but:
$ perf -h tui
didn't.
Make it support both cases and also look at the option help when neither
matches, so that he following examples works:
$ perf report -h interface
Usage: perf report [<options>]
--gtk Use the GTK2 interface
--stdio Use the stdio interface
--tui Use the TUI interface
$ perf report -h stack
Usage: perf report [<options>]
-g, --call-graph <print_type,threshold[,print_limit],order,
sort_key[,branch]>
Display call graph (stack chain/backtrace):
print_type: call graph printing style (graph|flat|fractal|none)
threshold: minimum call graph inclusion threshold (<percent>)
print_limit: maximum number of call graph entry (<number>)
order: call graph order (caller|callee)
sort_key: call graph sort key (function|address)
branch: include last branch info to call graph (branch)
Default: graph,0.5,caller,function
--max-stack <n> Set the maximum stack depth when parsing the
callchain, anything beyond the specified depth
will be ignored. Default: 127
$
Suggested-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-xzqvamzqv3cv0p6w3inhols3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently any time we need to access socket or core id for given cpu, we
access the sysfs topology file.
Adding a cpus_aggr_map cpu_map to cache those entries.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding cpu_map__empty_new interface to create empty cpumap with given
size. The cpumap entries are initialized with -1.
It'll be used for caching cpu_map in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Because the 'perf stat record' patches will use the id_offset member
together with the priv pointer.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-29-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
__pa() in the x86 pageattr code. Since these virtual addreses are
not part of the direct mapping or kernel text mapping, passing them
to __pa() will trigger a BUG_ON() when CONFIG_DEBUG_VIRTUAL is
enabled - Sai Praneeth Prakhya
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xdZV
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull EFI fix from Matt Fleming:
- Fix a kernel panic by not passing EFI virtual mapping addresses to
__pa() in the x86 pageattr code. Since these virtual addreses are
not part of the direct mapping or kernel text mapping, passing them
to __pa() will trigger a BUG_ON() when CONFIG_DEBUG_VIRTUAL is
enabled. (Sai Praneeth Prakhya)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The description of the XUSB_PADCTL_USB3_PAD_MUX_0 register in the Tegra124
documentation implies that all functions (pcie, usb3 and sata) can be
muxed onto to all lanes (pcie lanes 0-4 and sata lane 0). However, it has
been confirmed that this is not the case and the mux'ing options much more
limited. Unfortunately, the public documentation has not been updated to
reflect this and so detail the actual mux'ing options here by function:
Function: Lanes:
pcie1 x2: pcie3, pcie4
pcie1 x4: pcie1, pcie2, pcie3, pcie4
pcie2 x1 (option1): pcie0
pcie2 x1 (option2): pcie2
usb3 port 0: pcie0
usb3 port 1 (option 1): pcie1
usb3 port 1 (option 2): sata0
sata: sata0
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HW and driver support the GPIO as interrupt-controller.
Document that in the DT binding.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver does not have any real architecture dependencies. To avoid
listing each architecture that might use this driver on some
FPGA-enabled platform, drop these dependencies.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Broxton. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reserved for ACPI actually means that in such case the GPIO hardware will
not update the interrupt status register (GPI_IS) even if the pin is
configured to trigger an interrupt. It will update GPI_GPE_STS instead and
does not trigger an interrupt.
Allow using such pins as GPIOs, only prevent their usage as interrupts.
We also rename function intel_pad_reserved_for_acpi() to be
intel_pad_acpi_mode() which reflects the actual meaning better.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now usage_with_options() setup a pager before printing message so normal
printf() or pr_err() will not be shown. The usage_with_options_msg()
can be used to print some help message before usage strings.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445701767-12731-4-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On Intel Broxton the GPIO hardware consists of several chips that all share
the parent interrupt. It is not possible to handle this by setting chained
handler for each chip (as they will overwrite each other).
To overcome this we need to request the interrupt using devm_request_irq()
and pass IRQF_SHARED with the flags.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Returning an error instead of NULL in bgpio_map if
platform_get_resource_byname does not find a resource was introduced with
commit cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map").
This results in several qemu runtime failures with default and non-default
configurations, if attempts are made to boot from mmcblk0. Examples for
failures with multi_v7_defconfig are
Machine: vexpress-a9 dtb: vexpress-v2p-ca9
Machine: vexpress-a15 dtb: vexpress-v2p-ca15-tc1
Crash:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Looking into the code, always returning an error if bgpio_map fails
does not appear to make much sense, since the code in bgpio_setup_io
specifically supports some of the resources to be NULL.
Fixes: cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
Fixes: 6e90889202 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This new compatible string, "brcm,iproc-gpio", should be used for
all new iproc-based future SoCs.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpio to pinctrl pin mapping code from driver and
address this through standard property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO controller's pins are muxed, pin-controller subsystem
need to be intimated by defining mapping between gpio and
pinmux controller. This patch adds required properties to
define this mapping via DT.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While unifying how blkcg stats are collected, 77ea733884 ("blkcg:
move io_service_bytes and io_serviced stats into blkcg_gq")
incorrectly used bio->flags instead of bio->rw to tell the IO type.
This made IOs to be accounted as the wrong type. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 77ea733884 ("blkcg: move io_service_bytes and io_serviced stats into blkcg_gq")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
