Add support to set polarity on PWM devices, allowing for inverted
duty cycles.
Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.
A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5
PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.
This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.
This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for encoding PWM properties in bit encoded form with
of_pwm_xlate_with_flags() function support. Platforms require platform
specific PWM properties has to populate in 3rd cell of the pwm-specifier
and PWM driver should also set .of_xlate support with this function.
Currently PWM property polarity encoded in bit position 0 of the third
cell in pwm-specifier.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.
More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.
1. http://www.st.com/internet/mcu/product/251211.jsp
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch updates pwm-vt8500.c to support devicetree probing and
make use of the common clock subsystem.
A binding document describing the PWM controller found on
arch-vt8500 is also included.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
The second cell in the PWM specifier denotes the period in nanoseconds,
not the duty cycle. The latter can be freely configured at runtime and
a PWM with a fixed duty cycle would be rather pointless.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
At the same time remove platform based support. No user for
this driver has made it into mainline so far, so all we break
is out of tree stuff.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In the reg field we should annotate the register address space in hexadecimal
format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Encode soc name in the compatible string to know the specific version
hardware block. This is the general approach adopted for most bindings.
Change mxs-pwm binding to use the approach.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds helpers to support device tree bindings for the generic
PWM API. Device tree binding documentation for PWM controllers is also
provided.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
