For the forwarding selftests to work, we need network namespaces when
using veth/vrf otherwise ping/ping6 commands like these:
ip vrf exec vveth0 /bin/ping 192.0.2.2 -c 10 -i 0.1 -w 5
will fail because network namespaces may not be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global variable RET needs to be initialized before each call to
log_test. This test case sets it once before running the tests, but then
calls log_tests for every individual test. Thus a failure in one of the
tests causes spurious failures in follow-up tests as well.
Fix by moving the initialization of RET from test_all() to
full_test_span_gre_dir_acl(), a function that implements the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test sets up mirroring such that it mirrors all overlay traffic.
That includes ARP, which causes occasional miscounts and spurious
failures. Ignore ARP explicitly to avoid these problems.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test relies on routing in the primary traffic path, but neglects to
enable forwarding. Do so.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After one LAG slave is downed and another upped, it takes a while for
the neighbor on a bridge to time out and get renegotiated. The test does
prompt update of FDB entries by arpinging. But because the neighbor
still references another address, offloading is not possible, and some
packets may end up not being mirrored.
To force the neighbor renegotiation, simply flush the neighbor table at
the bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARP or ND traffic can cause spurious migration of FDB back to $swp3.
Mirroring is then updated in accordance with the change, and mirrored
packets are seen at h3, causing a failure.
Detect the case of this spurious roaming, and retry the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged egress test sets up mirroring to {,ip6}gretap such that the
underlay goes through a bridge. Then VLAN flags are manipulated to test
that the traffic leaves the bridge 802.1q-tagged or not, as appropriate.
However, when a neighbor expires at the time that the bridge VLAN is
configured as PVID and egress untagged, the following discovery process
can't finish, because the IP address on H3 is still at the VLAN-tagged
netdevice. This manifests by occasional failures where only several of
the 10 required packets get through.
Therefore, when reconfiguring the VLAN flags, move the IP address to the
appropriate device in the H3 VRF.
In addition to that, take this opportunity to embed an ASCII art diagram
to make the topology move obvious.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in an environment with poor performance (such as a
simulator), processing mirrored packets can take a while. Evaluating the
condition too soon leads to spurious "seen 9, expected 10" failures as
the last packet doesn't have enough time to get mirrored and the mirror
to arrive and bump the observed counters.
Wait for one ping interval before evaluating the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a simulator, the TTL change takes a while to settle and
during this time the performance of the packet processing is lowered.
The resulting instability leads to ping sending more packets as it
assumes some have been dropped. This then leads to regular spurious
failures as more packets than expected are observed.
Sleep a bit to give the system time to stabilize.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. Those
are mirrored, and over a certain threshold the test case run is
considered a failure, because too much traffic is observed.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier to distinguish "[ OK ]" from "[FAIL]" than "[PASS]".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARP suppression allows the Linux bridge to answer ARP requests on behalf
of remote hosts. It reduces the amount of packets a VTEP needs to flood.
This test verifies that ARP suppression on / off works when a neighbour
exists and when it does not exist. It does so by sending an ARP request
from a host connected to one VTEP and checking whether it was received
by a second VTEP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VXLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI. Different tenants
(VRFs) use different L3 VNIs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that ARP packets are correctly decapsulated by the ingress VTEP
by removing the neighbours configured on both VLAN interfaces and
running a ping test.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In asymmetric routing the ingress VTEP routes the packet into the
correct VXLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.
The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).
While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on flat topology described in file
ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on flat topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a library with helper functions, to be used in testing IP-in-IP and GRE
tunnels, both in flat and in hierarchical topologies.
The topologies used in this library cover the three scenarios of tunnels -
a tunel with no bound device, a tunnel with bound device in the same VRF
and a tunnel with a bound device in a different VRF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that externally learned FDB entries can roam, but not age out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a VLAN on a bridge port, delete it and make sure the PVID VLAN is
not affected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the test on the Spectrum ASIC the generated packets are
counted on the ingress filter and injected back to the pipeline because
of the 'pass' action. The router block then drops the packets due to
checksum error, as the test generates packets with zero checksum.
When running the test on an emulator that is not as strict about
checksum errors the test fails since packets are counted twice. Once by
the emulated ASIC on its ingress filter and again by the kernel as the
emulator does not perform checksum validation and allows the packets to
be trapped by a matching host route.
Fix this by changing the action to 'drop', which will prevent the packet
from continuing further in the pipeline to the router block.
For veth pairs this change is essentially a NOP given packets are only
processed once (by the kernel).
Fixes: a0b61f3d8e ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.
Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using VLAN-aware bridges with VXLAN, the VLAN that is mapped to the
VNI of the VXLAN device is that which is configured as "pvid untagged"
on the corresponding bridge port.
When these flags are toggled or when the VLAN is deleted entirely,
remote hosts should not be able to receive packets from the VTEP.
Add a test case for above mentioned scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test is very similar to its VLAN-unaware counterpart
(vxlan_bridge_1d.sh), but instead of using multiple VLAN-unaware
bridges, a single VLAN-aware bridge is used with multiple VLANs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that ECN bits in the VXLAN envelope are correctly deduced from the
overlay packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that TOS is inherited from the tunneled packet into the envelope as
configured at the VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether TTL of VXLAN envelope packets is properly set based
on the device configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ordering of the topology creation can have impact on whether a
driver is successful in offloading VXLAN. Therefore add a pseudo-test
that reshuffles bits of the topology, and then reruns the same suite of
tests again to make sure that the new setup is supported as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to a learned MAC address, the traffic is
forwarded accurately only to the right endpoint.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when sending traffic to an unlearned MAC address, the traffic
is flooded to both remote VXLAN endpoints.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test end-to-end reachability between local and remote endpoints.
Note that because learning is disabled on the VXLAN device, the ICMP
requests will end up being flooded to all remotes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This skeleton sets up a topology with three VXLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.
Since VXLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such a function will be useful for counting malformed packets in the ECN
decap test.
To that end, introduce a common handler for handling stat-fetching, and
reuse it in link_stats_tx_packets_get() and link_stats_rx_errors_get().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ping routine more generic by allowing passing arbitrary ping
command-line arguments.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ping_test() recognize an optional argument with a description of
the test. This is handy if there are several ping test, to make it clear
which is which.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to run a certain command inside another network namespace, it's
possible to use "ip netns exec ns command". However then one can't use
functions defined in lib.sh or a test suite.
One option is to do "ip netns exec ns bash -c command", provided that
all functions that one wishes to use (and their dependencies) are
published using "export -f". That may not be practical.
Therefore, introduce a helper in_ns(), which wraps a given command in a
boilerplate of "ip netns exec" and "source lib.sh", thus making all
library functions available. (Custom functions that a script wishes to
run within a namespace still need to be exported.)
Because quotes in "$@" aren't recognized in heredoc, hand-expand the
array in an explicit for loop, leveraging printf %q to handle proper
quoting.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the case of NUM_NETIFS of 0 has not been interesting. However if
one wishes to reuse the lib.sh routines in a setup of a separate
namespace, being able to import like this is handy.
Therefore replace the {1..$NUM_NETIFS} references, which cause iteration
over 1 and 0, with an explicit for loop like we do in setup_wait() and
tc_offload_check(), so that for NUM_NETIFS of 0 no iteration is done.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immediately after mlxsw module is probed and lldpad started, added APP
entries are briefly in "unknown" state before becoming "pending". That's
the state that lldpad_app_wait_set() typically sees, and since there are
no pending entries at that time, it bails out. However the entries have
not been pushed to the kernel yet at that point, and thus the test case
fails.
Fix by waiting for both unknown and pending entries to disappear before
proceeding.
Fixes: d159261f36 ("selftests: mlxsw: Add test for trust-DSCP")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test adds an fdb entry with the sticky flag and sends traffic from
a different port with the same mac as a source address expecting the entry
to not change ports if the flag is operating correctly.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
