intel-pinctrl for v5.10-2
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1604561884-10166-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:
000 none
001 1 kOhm (if available)
010 5 kOhm
100 20 kOhm
As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:
011 ~833.3 Ohm
101 ~952.4 Ohm
110 ~4 kOhm
111 ~800 Ohm
That said, convert TERM definitions to be the bit masks to reflect the above.
While at it, enable the same setting for pull down case.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Pull GPIO updates from Linus Walleij:
"This time very little driver changes but lots of core changes.
We have some interesting cooperative work for ARM and Intel alike,
making the GPIO subsystem more and more suitable for industrial
systems and the like, in addition to the in-kernel users.
We touch driver core (device properties) and lib/* by adding one
simple string array free function, these are authored by Andy
Shevchenko who is a well known and recognized core helpers maintainers
so this should be fine.
We also see some Android GKI-related modularization in the MXC
drivers.
Core changes:
- The big core change is the updated (v2) userspace character device
API.
This corrects badly designed 64-bit alignment around the line
events. We also add the debounce request feature. This echoes the
often quotes passage from Frederick Brooks "The mythical man-month"
to always throw one away, which we have seen before in things such
as V4L2. So we put in a new one and deprecate and obsolete the old
one.
- All example tools in tools/gpio/* are migrated to the new API to
set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in device
properties.
- Provide a generic library function kfree_strarray() that can be
used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now uses the
IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial code
clean-up and now use more of the core kernel inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized, which
makes modularized GKI Android kernels happy"
* tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpiolib: Update header block in gpiolib-cdev.h
gpiolib: cdev: switch from kstrdup() to kstrndup()
docs: gpio: add a new document to its index.rst
gpio: pca953x: Add support for the NXP PCAL9554B/C
tools: gpio: add debounce support to gpio-event-mon
tools: gpio: add multi-line monitoring to gpio-event-mon
tools: gpio: port gpio-event-mon to v2 uAPI
tools: gpio: port gpio-hammer to v2 uAPI
tools: gpio: rename nlines to num_lines
tools: gpio: port gpio-watch to v2 uAPI
tools: gpio: port lsgpio to v2 uAPI
gpio: uapi: document uAPI v1 as deprecated
gpiolib: cdev: support setting debounce
gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL
gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL
gpiolib: cdev: support edge detection for uAPI v2
gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL
gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL
gpiolib: add build option for CDEV v1 ABI
gpiolib: make cdev a build option
...
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
msmgpio irqchip was not using return value of irq_set_irq_wake() callback
since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor
it implemented .irq_set_wake callback. This lead to irq_set_irq_wake()
return error -ENXIO.
However from 'commit 4110b5cbb0 ("irqchip/gic-v3: Allow interrupt to be
configured as wake-up sources")' GIC irqchip has IRQCHIP_SKIP_SET_WAKE
flag.
Use return value from irq_set_irq_wake() and irq_chip_set_wake_parent()
instead of always returning success.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-3-git-send-email-mkshah@codeaurora.org
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-2-git-send-email-mkshah@codeaurora.org
When PINCTRL_BCM2835 is enabled and GPIOLIB is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_BCM2835 [=y] && PINCTRL [=y] && OF [=y] && (ARCH_BCM2835 [=n] || ARCH_BRCMSTB [=n] || COMPILE_TEST [=y])
The reason is that PINCTRL_BCM2835 selects GPIOLIB_IRQCHIP without
depending on or selecting GPIOLIB while GPIOLIB_IRQCHIP is subordinate to
GPIOLIB.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200914144025.371370-1-fazilyildiran@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed pinconf data structures are split into 'conf' and 'map'
types, where the 'conf' struct defines which register and bitfield to
manipulate, while the 'map' struct defines what value to write to
the register and bitfield.
Both structs have a mask member, and the wrong mask was being used to
tell the regmap which bits to update.
A todo is to look at whether we can remove the mask from the 'map'
struct.
Fixes: 5f52c85384 ("pinctrl: aspeed: Use masks to describe pinconf bitfields")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Link: https://lore.kernel.org/r/20200910025631.2996342-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use function callbacks for SCU related functions in pinctrl-imx.c
in order to support the scenario of PINCTRL_IMX is built in while
PINCTRL_IMX_SCU is built as module, all drivers using SCU pinctrl
driver need to initialize the SCU related function callback, and
no need to check CONFIG_PINCTRL_IMX_SCU anymore, hence stub functions
also can be removed.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1599552721-24872-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v5.10-1
* Add last part of cleanup Cherryview driver to align with other drivers
* Due to above clean up Cherryview and Baytrail drivers to use common API
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to use intel_pinctrl_get_soc_data()
cherryview:
- Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
- Switch to use intel_pinctrl_get_soc_data()
- Utilize temporary variable to hold device pointer
- Switch to use struct intel_pinctrl
- Move custom community members to separate data struct
- Drop stale comment
intel:
- Update header block to reflect direct dependencies
- Extract intel_pinctrl_get_soc_data() helper for wider use
pinctrl: renesas: Updates for v5.10
- Add CAN and USB1 PWEN pin groups on R-Car H2 and RZ/G1,
- Three more conversion of DT bindings to json-schema,
- Group all Renesas pinctrl drivers and improve visual Kconfig
structure,
- Rename drivers/pinctrl/sh-pfc to drivers/pinctrl/renesas,
- Minor fixes and improvements.
