Use ethtool -S to query physical layer statistical counters including:
- rx_symbol_errors_phy: Number of symbol errors that were not corrected
by FEC correction algorithm or that FEC was not active on this interface.
- rx_corrected_bits_phy: Number of corrected bits according to active
FEC (RS/FC).
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Today when the driver enter to promiscuous mode or vlan
filter is disabled, we add flow rule to receive any c-taggd
packets, therefore s-tagged packets are dropped.
In order to receive s-tagged packets as well we need to add
flow rule to receive any s-tagged packet.
Fixes: 7cb21b794b ('net/mlx5e: Rename en_flow_table.c to en_fs.c')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch enables the 1PPS IN and 1PPS OUT support according
to the advertised HCA capability. Single pin may be configured
to one of the above mutual exclusive functions via standard
Linux tools and APIs. For example, testptp open source application.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement query and set functionality for MTPPS and MTPPSE registers.
MTPPS (Management Pulse Per Second) provides the device PPS capabilities,
configures the PPS in and out modules and holds the PPS in time stamp.
Query MTPPS is supported only when HCA_CAP.pps is set and modify is supported
when HCA_CAP.pps_modify is set.
MTPPSE (Management Pulse Per Second Event) configures the different event
generation modes for PPS. Supported when HCA_CAP.pps is set.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Firmware representation of the firmware version on the health buffer has
changed for newer device. The representation in the initialization
segment does not and will not change. In addition, we print the health
buffer firmware version as a raw hex number.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Infiniband part of mlx5 driver can be compiled as a module
or as a part of bzImage (compiled in). In the second case,
the call to request_module will return an error -ENOENT.
It will cause to a misleading print "failed request module
on mlx5_ib".
This patch removes this print, In order to comply with mlx4.
Fixes: f66f049fb7 ("net/mlx5_core: Request the mlx5 IB module on driver load")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds bpf_xdp_adjust_head() support to mlx5e.
1. rx_headroom is added to struct mlx5e_rq. It uses
an existing 4 byte hole in the struct.
2. The adjusted data length is checked against
MLX5E_XDP_MIN_INLINE and MLX5E_SW2HW_MTU(rq->netdev->mtu).
3. The macro MLX5E_SW2HW_MTU is moved from en_main.c to en.h.
MLX5E_HW2SW_MTU is also moved to en.h for symmetric reason
but it is not a must.
v2:
- Keep the xdp specific logic in mlx5e_xdp_handle()
- Update dma_len after the sanity checks in mlx5e_xmit_xdp_frame()
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb5 ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save the qp context flags byte containing the flag disabling vlan stripping
in the RESET to INIT qp transition, rather than in the INIT to RTR
transition. Per the firmware spec, the flags in this byte are active
in the RESET to INIT transition.
As a result of saving the flags in the incorrect qp transition, when
switching dynamically from VGT to VST and back to VGT, the vlan
remained stripped (as is required for VST) and did not return to
not-stripped (as is required for VGT).
Fixes: f0f829bf42 ("net/mlx4_core: Add immediate activate for VGT->VST->VGT")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_cq_completion() and mlx4_cq_event(), the
radix_tree_lookup requires a rcu_read_lock.
This is mandatory: if another core frees the CQ, it could
run the radix_tree_node_rcu_free() call_rcu() callback while
its being used by the radix tree lookup function.
Additionally, in function mlx4_cq_event(), since we are adding
the rcu lock around the radix-tree lookup, we no longer need to take
the spinlock. Also, the synchronize_irq() call for the async event
eliminates the need for incrementing the cq reference count in
mlx4_cq_event().
Other changes:
1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock:
we no longer take this spinlock in the interrupt context.
The spinlock here, therefore, simply protects against different
threads simultaneously invoking mlx4_cq_free() for different cq's.
2. In function mlx4_cq_free(), we move the radix tree delete to before
the synchronize_irq() calls. This guarantees that we will not
access this cq during any subsequent interrupts, and therefore can
safely free the CQ after the synchronize_irq calls. The rcu_read_lock
in the interrupt handlers only needs to protect against corrupting the
radix tree; the interrupt handlers may access the cq outside the
rcu_read_lock due to the synchronize_irq calls which protect against
premature freeing of the cq.
3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg.
4. We leave the cq reference count mechanism in place, because it is
still needed for the cq completion tasklet mechanism.
Fixes: 6d90aa5cf1 ("net/mlx4_core: Make sure there are no pending async events when freeing CQ")
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As found by Olof's build bot, we gain a harmless warning about a
potential uninitialized variable reference in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'parse_tc_fdb_actions':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:769:13: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:811:21: note: 'out_dev' was declared here
This was introduced through the addition of an 'IS_ERR/PTR_ERR' pair
that gcc is unfortunately unable to completely figure out.
The problem being gcc cannot tell that if(IS_ERR()) in
mlx5e_route_lookup_ipv4() is equivalent to checking if(err) later,
so it assumes that 'out_dev' is used after the 'return PTR_ERR(rt)'.
The PTR_ERR_OR_ZERO() case by comparison is fairly easy to detect
by gcc, so it can't get that wrong, so it no longer warns.
Hadar Hen Zion already attempted to fix the warning earlier by adding fake
initializations, but that ended up not fully addressing all warnings, so
I'm reverting it now that it is no longer needed.
Link: http://arm-soc.lixom.net/buildlogs/mainline/v4.10-rc3-98-gcff3b2c/
Fixes: a42485eb0e ("net/mlx5e: TC ipv4 tunnel encap offload error flow fixes")
Fixes: a757d108dc ("net/mlx5e: Fix kbuild warnings for uninitialized parameters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable BH around the call to napi_schedule() to avoid following warning
[ 52.095499] NOHZ: local_softirq_pending 08
[ 52.421291] NOHZ: local_softirq_pending 08
[ 52.608313] NOHZ: local_softirq_pending 08
Fixes: 8d59de8f7b ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event_data starts from address 0x00-0x0C and not from 0x08-0x014. This
leads to duplication with other fields in the Event Queue Element such as
sub-type, cqn and owner.
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.
Fix this by adding the original skb release to the main path.
Fixes: d003462a50 ("mlxsw: Simplify mlxsw_sx_port_xmit function")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.
Fix this by adding the original skb release to the main path.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not attempt to drain the health workqueue when unloading the device in
the recovery flow, this can cause a deadlock when the recovery work
tries to cancel itself with sync.
Because the work is no longer unconditionally canceled when unloading, it
must be explicitly canceled in the AER flow.
fixes: 689a248df8 ("net/mlx5: Cancel recovery work in remove flow")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to do interface down or changing interface configuration
under heavy traffic, some of the adaptive moderation corner cases can
occur and leave a WARN_ONCE call trace in the kernel log.
Those WARN_ONCE are meant for debug only, and should have been inserted
only under debug. We avoid such call traces by removing those WARN_ONCE.
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code before this patch registered uplink e-Switch representor
on nic_enable and unregistered on nic_cleanup, the right place
for this unregister is in nic_disable.
Fixes: 127ea380ac ("net/mlx5: Add Representors registration API")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware returns an error (common example is an attempt to
add twice the same rule which is refused by the some FWs), we are not
properly derefing/cleaning few resources allocated on the way.
Examples are vport vlan deref under eswitch vlan offloads, and encap
entry/neighbour deref under eswitch encapsulation offloads, fix that.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild warn about parameters that may be used uninitialized, fix it.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For e-switch level matching on packets being an IP fragment, we
need to make sure the source vport inline mode is L3, fix that.
Fixes: 3f7d0eb42d ('net/mlx5e: Offload TC matching on packets being IP fragments')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As done elsewhere in our TC/flower offload code, the address type of
the encapsulation IP headers should be realized accroding to the
addr_type field of the encapsulation control dissector key, do that.
Fixes: bbd00f7e23 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the route lookup fails we should return the actual error.
When the neigh isn't valid, we should return -EOPNOTSUPP as done
in similar cases along the code.
When the offload can't take place as of invalid neigh etc, we
must release the neigh.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We silently reject offloading of IPv6 tunnels, non vxlan tunnels,
vxlan tunnels where the dst port to match is not provided, etc.
Be a bit more verbose and print a warning so the user better
realizes what went wrong here and can fix it.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes: bbd00f7e23 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can offload the matching on source udp port of ip tunnels for
decapsulation. We can not offload setting source udp port for tunnels
as part of encapsulation. Fix both the code that deals with matching
offload (decap) and the code that deal with encap offload to align with
that.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes: bbd00f7e23 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit b45f0674b9 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs"),
it changed EOPNOTSUPP to ENOTSUPP by mistake. This patch fixes it.
Fixes: b45f0674b9 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches optimizes the usage of the UAR area which is
contained within the BAR 0-1. Previous versions of the firmware and the driver
assumed each system page contains a single UAR. This patch set will query the
firmware for a new capability that if published, means that the firmware can
support UARs of fixed 4K regardless of system page size. In the case of
powerpc, where page size equals 64KB, this means we can utilize 16 UARs per
system page. Since user space processes by default consume eight UARs per
context this means that with this change a process will need a single system
page to fulfill that requirement and in fact make use of more UARs which is
better in terms of performance.
In addition to optimizing user-space processes, we introduce an allocator
that can be used by kernel consumers to allocate blue flame registers
(which are areas within a UAR that are used to write doorbells). This provides
further optimization on using the UAR area since the Ethernet driver makes
use of a single blue flame register per system page and now it will use two
blue flame registers per 4K.
The series also makes changes to naming conventions and now the terms used in
the driver code match the terms used in the PRM (programmers reference manual).
Thus, what used to be called UUAR (micro UAR) is now called BFREG (blue flame
register).
In order to support compatibility between different versions of
library/driver/firmware, the library has now means to notify the kernel driver
that it supports the new scheme and the kernel can notify the library if it
supports this extension. So mixed versions of libraries can run concurrently
without any issues.
Thanks,
Eli and Matan
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYc9kSAAoJEEg/ir3gV/o+a0EH/jEGiopH7CHc4T4nXT1I4kQa
TicrkMNV3Sr9MBWwn8TLOyx+Fi1dex4cumrJI/BNVjC6h/nS6JHbslYoZxTkX9lT
L0vRsHJBVr/PODqimIGNnlJFBPhNJSGiHG4JHlJHlpvcGNahitN3gXmUjcRNju+V
ExnvgwWzAXM0qg1qWf5A/3HmqbtYES1rJXQUsimtc2QAif/SIayBD4fEA8x5zNBA
i0p8xcDrzUqmeblkpnsJA3w40s1rsuqvJnvLPDpbpKENtHfw1UFZ2987P7LvOrIv
NF/mZBkStC0gOZX6dLEAdoZXL1gTsJX19hTkUMfYH4BHqHARa2/oCS3wcCf1Giw=
=C+cp
-----END PGP SIGNATURE-----
Merge tag 'mlx5-4kuar-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5 4K UAR
The following series of patches optimizes the usage of the UAR area which is
contained within the BAR 0-1. Previous versions of the firmware and the driver
assumed each system page contains a single UAR. This patch set will query the
firmware for a new capability that if published, means that the firmware can
support UARs of fixed 4K regardless of system page size. In the case of
powerpc, where page size equals 64KB, this means we can utilize 16 UARs per
system page. Since user space processes by default consume eight UARs per
context this means that with this change a process will need a single system
page to fulfill that requirement and in fact make use of more UARs which is
better in terms of performance.
In addition to optimizing user-space processes, we introduce an allocator
that can be used by kernel consumers to allocate blue flame registers
(which are areas within a UAR that are used to write doorbells). This provides
further optimization on using the UAR area since the Ethernet driver makes
use of a single blue flame register per system page and now it will use two
blue flame registers per 4K.
The series also makes changes to naming conventions and now the terms used in
the driver code match the terms used in the PRM (programmers reference manual).
Thus, what used to be called UUAR (micro UAR) is now called BFREG (blue flame
register).
In order to support compatibility between different versions of
library/driver/firmware, the library has now means to notify the kernel driver
that it supports the new scheme and the kernel can notify the library if it
supports this extension. So mixed versions of libraries can run concurrently
without any issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the order of the free directives to match the port init function
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably some copy-paste error from "int_msix" that caused "int_" prefix to
appear in the comments for all "eq_" APIs.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err" variable is been checked, return always 0.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Activate 4K UAR support for firmware versions that support it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add fields to structs to convey to kernel an indication whether the
library supports multi UARs per page and return to the library the size
of a UAR based on the queried value.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make use of the blue flame registers allocator at mlx5_ib. Since blue
flame was not really supported we remove all the code that is related to
blue flame and we let all consumers to use the same blue flame register.
Once blue flame is supported we will add the code. As part of this patch
we also move the definition of struct mlx5_bf to mlx5_ib.h as it is only
used by mlx5_ib.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A reference to a UAR is required to generate CQ or EQ doorbells. Since
CQ or EQ doorbells can all be generated using the same UAR area without
any effect on performance, we are just getting a reference to any
available UAR, If one is not available we allocate it but we don't waste
the blue flame registers it can provide and we will use them for
subsequent allocations.
We get a reference to such UAR and put in mlx5_priv so any kernel
consumer can make use of it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is an implementation of an allocator that allocates blue flame
registers. A blue flame register is used for generating send doorbells.
A blue flame register can be used to generate either a regular doorbell
or a blue flame doorbell where the data to be sent is written to the
device's I/O memory hence saving the need to read the data from memory.
For blue flame kind of doorbells to succeed, the blue flame register
need to be mapped as write combining. The user can specify what kind of
send doorbells she wishes to use. If she requested write combining
mapping but that failed, the allocator will fall back to non write
combining mapping and will indicate that to the user.
Subsequent patches in this series will make use of this allocator.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This establishes a solid naming conventions for UARs. A UAR (User Access
Region) can have size identical to a system page or can be fixed 4KB
depending on a value queried by firmware. Each UAR always has 4 blue
flame register which are used to post doorbell to send queue. In
addition, a UAR has section used for posting doorbells to CQs or EQs. In
this patch we change names to reflect this conventions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* Update page fault event according to last specification.
* Separate code path for page fault EQ, completion EQ and async EQ.
* Move page fault handling work queue from mlx5_ib static variable
into mlx5_core page fault EQ.
* Allocate memory to store ODP event dynamically as the
events arrive, since in atomic context - use mempool.
* Make mlx5_ib page fault handler run in process context.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update PAGE_FAULT_RESUME command layout.
Three bit fields describing page fault: rdma, rdma_write, req_res gave 8
possible combinations, while only a few were legal. Now they
are interpreted as three-bit type field, where former legal
combinations turns into corresponding types and unused were added as new
types.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this change we turn mlx5_ib_update_mtt() into generic
mlx5_ib_update_xlt() to perfrom HCA translation table modifiactions
supporting both atomic and process contexts and not limited by number
of modified entries.
Using this function we increase preallocated MRs up to 16GB.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Update struct mlx5_wqe_umr_ctrl_seg.
* Currenlty UMR send_flags aim only certain use cases: enabled/disable
cached MR, modifying XLT for ODP. By making flags independent make UMR
more flexible allowing arbitrary manipulations.
* Since different UMR formats have different entry sizes UMR request
should receive exact size of translation table update instead of
number of entries. Rename field npages to xlt_size in struct mlx5_umr_wr
and update relevant code accordingly.
* Add support of length64 bit.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
