Commit Graph

238 Commits

Author SHA1 Message Date
Archit Taneja
d21f43bc39 OMAPDSS: Remove passive matrix LCD support (part 3)
Remove omap_lcd_display_type enum

The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:15:46 +03:00
Archit Taneja
6d523e7b0e OMAPDSS: Remove passive matrix LCD support (part 1)
Remove clock constraints related to passive matrix displays.

There is a constraint (pcd_min should be 3) for passive matrix displays. Remove
this constraint in clock divider calculations as we won't support passive
matrix displays any more.

This cleans up the functions which calculate the clock dividers with DSI's PLL
or DSS_FCLK as the clock source.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 10:10:03 +03:00
Chandrabhanu Mahapatra
6f1891fc70 OMAPDSS: Add dump and debug support for LCD3
DISPC functions have been modified to provide clock and register dumps and debug
support for the LCD3 manager.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 09:41:29 +03:00
Chandrabhanu Mahapatra
e86d456a23 OMAPDSS: Add LCD3 overlay manager and Clock and IRQ support
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.

The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 09:41:24 +03:00
Chandrabhanu Mahapatra
efa70b3b7d OMAPDSS: Cleanup implementation of LCD channels
The current implementation of LCD channels and managers consists of a number of
if-else construct which has been replaced by a simpler interface. A constant
structure mgr_desc has been created in Display Controller (DISPC) module. The
mgr_desc contains for each channel its name, irqs and  is initialized one time
with all registers and their corresponding fields to be written to enable
various features of Display Subsystem. This structure is later used by various
functions of DISPC which simplifies the further implementation of LCD channels
and its corresponding managers.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 09:41:15 +03:00
Tomi Valkeinen
5be3aebd09 OMAPDSS: fix warnings if CONFIG_PM_RUNTIME=n
If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.

One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.

However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>
2012-06-29 09:09:49 +03:00
Archit Taneja
2aefad49d8 OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
DSS2 driver uses the timings in manager's private data to check the validity of
overlay and manager infos written by the user. For VENC interface, we divide the
Y resolution by half when writing to the DISPC_DIGIT_SIZE register as the
content is interlaced. However, the height of the manager/display with respect
to the content shown through VENC still remains the same.

The VENC driver divides the y_res parameter in omap_video_timings by half, and
then applies the configuration. This leads to manager's private data storing
the wrong Y resolution. Hence, overlay related checks fail.

Ensure that manager's private data stores the original timings, and the Y
resolution is halved only when we write to the DISPC register. This is a hack,
the proper solution would be to pass some sort of interlace parameter which
makes the call whether we should divide y_res or not.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-22 11:00:01 +03:00
Chandrabhanu Mahapatra
65e006ff4b OMAPDSS: DISPC: Support rotation through TILER
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.

When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.

The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-22 10:59:15 +03:00
Tomi Valkeinen
c6eee968d4 OMAPDSS: remove compiler warnings when CONFIG_BUG=n
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.

This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-22 10:59:14 +03:00
Tomi Valkeinen
36377357db OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
Commit 05dd0f5308 ("OMAPDSS: DISPC: Update
Accumulator configuration for chroma plane") adds
dispc_ovl_set_accu_uv() function that sets the accu, but the function
only handles YUV and NV12 modes, and BUGs otherwise.

The patch also adds a call to the function, but unfortunately the place
of call was such that the mode could be other than YUV or NV12, thus
crashing the driver.

This patchs moves the call to a slightly later spot, at which point only
YUV and NV12 modes are handled.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Chandrabhanu Mahapatra <cmahapatra@ti.com>
2012-05-22 10:59:14 +03:00
Tomi Valkeinen
3568f2a46f OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
There is a problem related to DSS FIFO thresholds and power management
on OMAP3. It seems that when the full PM hits in, we get underflows. The
core reason is unknown, but after experiments it looks like only
particular FIFO thresholds work correctly.

This bug is related to an earlier patch, which added special FIFO
threshold configuration for OMAP3, because DSI command mode output
didn't work with the normal threshold configuration.

However, as the above work-around worked fine for other output types
also, we currently always configure thresholds in this special way on
OMAP3. In theory there should be negligible difference with this special
way and the standard way. The first paragraph explains what happens in
practice.

This patch changes the driver to use the special threshold configuration
only when the output is a manual update display on OMAP3. This does
include RFBI displays also, and although it hasn't been tested (no
boards using RFBI) I suspect the similar behaviour is present there
also, as the DISPC side should work similarly for DSI command mode and
RFBI.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Joe Woodward <jw@terrafix.co.uk>
2012-05-22 10:59:13 +03:00
Chandrabhanu Mahapatra
05dd0f5308 OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
DISPC has two accumulator registers DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 each
with horizontal and vertical bit fields. The bit fields can take values in the
range of -1024 to 1023. Based on bit field values DISPC decides on which one out
of 8 phases the filtering starts. DISPC_VIDp_ACCU_0 is used for progressive
output and for interlaced output both DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1
are used.

The current accumulator values in DISPC scaling logic for chroma plane takes
default values for all color modes and rotation types. So, the horizontal and
vertical up and downsampling accumulator bit field values have been updated for
better performance.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-15 13:51:56 +03:00
Tomi Valkeinen
6e7e8f06b2 OMAPDSS: add __init & __exit
Now that we are using platform_driver_probe() we can add __inits and
__exits all around.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:52 +03:00
Tomi Valkeinen
e40402cf18 OMAPDSS: move the creation of debugfs files
Instead of having an ugly #ifdef mess in the core.c for creating debugfs
files, add a dss_debugfs_create_file() function that the dss drivers
can use to create the debugfs files.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:52 +03:00
Tomi Valkeinen
852f083843 OMAPDSS: remove uses of dss_runtime_get/put
Now that the omapdss_core device is the parent for all other dss
devices, we don't need to use the dss_runtime_get/put anymore. Instead,
enabling omapdss_core will happen automatically when a child device is
enabled.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:51 +03:00
Tomi Valkeinen
11436e1dd2 OMAPDSS: use platform_driver_probe for core/dispc/dss
The platform devices for omapdss, dss and dispc drivers are always
present, so we can use platform_driver_probe instead of
platform_driver_register.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:51 +03:00
Tomi Valkeinen
04c742c3dc OMAPDSS: remove return from platform_driver_unreg
For unknown reasons we seem to have a return in each of the omapdss's
uninit functions, which is a void function.

Remove the returns.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:51 +03:00
Tomi Valkeinen
00928eaf52 OMAPDSS: clean up the omapdss platform data mess
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-11 14:44:51 +03:00
Archit Taneja
81ab95b7ec OMAPDSS: DISPC: Remove usage of dispc_mgr_get_device()
The functions calc_fclk_five_taps() and check_horiz_timing_omap3() use the
function dispc_mgr_get_device() to get the omap_dss_device pointer to which
the manager is connected, the width of the panel is derived from that.

The manager's timing is stored in it's private data in APPLY. This contains
the latest timings applied to the manager. Pass these timings to
dispc_ovl_setup() and use them in the above functions. Remove the function
dispc_mgr_get_device() as it isn't used any more.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-05-09 13:44:09 +03:00
Archit Taneja
3fa03ba854 OMAPDSS: DISPC: Remove omap_dss_device pointer usage from dispc_mgr_pclk_rate()
The pixel clock rate for the TV manager is calculated by checking the device
type connected to the manager, and then requesting the VENC/HDMI interface for
the pixel clock rate.

Remove the use of omap_dss_device pointer from here by checking which interface
generates the pixel clock by reading the DSS_CTRL.VENC_HDMI_SWITCH bit.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-05-09 13:44:09 +03:00
Archit Taneja
b917fa3961 OMAPDSS: MANAGER: Create a function to check manager timings
Create a function dss_mgr_check_timings() which wraps around the function
dispc_mgr_timings_ok(). This is mainly a clean up to hide dispc functions
from interface drivers.

dss_mgr_check_timings() is added in the function dss_mgr_check(), it currently
takes the timings maintained in the omap_dss_device struct. This would be later
replaced by the timings stored in the manager's private data.

Make dss_mgr_check_timings() and dispc_mgr_timings_ok() take a const
omap_video_timings pointer since these functions just check the timings.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-05-09 13:44:07 +03:00
Archit Taneja
408d9dbbc4 OMAPDSS: DISPC: Remove Fake VSYNC support
Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-09 13:43:17 +03:00
Chandrabhanu Mahapatra
8b53d99119 OMAPDSS: DISPC: Correct DISPC functional clock usage
DISPC_FCLK is incorrectly used as functional clock of DISPC in scaling
calculations. So, DISPC_CORE_CLK replaces as functional clock of DISPC.
DISPC_CORE_CLK is derived from DISPC_FCLK divided by an independent DISPC
divisor LCD.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-03 16:13:01 +03:00
Chandrabhanu Mahapatra
7faa92339b OMAPDSS: DISPC: Handle synclost errors in OMAP3
In OMAP3 DISPC video overlays suffer from some undocumented horizontal position
and timing related limitations leading to SYNCLOST errors. Whenever the image
window is moved towards the right of the screen SYNCLOST errors become
frequent. Checks have been implemented to see that DISPC driver rejects
configuration exceeding above limitations.

This code was successfully tested on OMAP3. This code is written based on code
written by Ville Syrjälä <ville.syrjala@nokia.com> in Linux OMAP kernel. Ville
Syrjälä <ville.syrjala@nokia.com> had added checks for video overlay horizontal
timing and DISPC horizontal blanking length limitations.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-03 16:12:57 +03:00
Chandrabhanu Mahapatra
aed74b5500 OMAPDSS: DISPC: Enable predecimation
In OMAP3 and OMAP4, the DISPC Scaler can downscale an image up to 4 times, and
up to 2 times in OMAP2. However, with predecimation, the image can be reduced
to 16 times by fetching only the necessary pixels in memory. Then this
predecimated image can be downscaled further by the DISPC scaler.

The pipeline is configured to use a burst of size 8 * 128 bits which consists
of 8 mini bursts of 16 bytes each. So, horizontal predecimation more than 16
can lead to complete discarding of such mini bursts. L3 interconnect may
handover the bus to some other initiator and inturn delay the fetching of
pixels leading to underflows. So, maximum predecimation limit is fixed at 16.

Based on the downscaling required, a prior calculation of predecimation values
for width and height of an image is done. Since, Predecimation reduces quality
of an image higher priorty is given to DISPC Scaler for downscaling.

This code was successfully tested on OMAP2, OMAP3 and OMAP4. Horizontal and
vertical predecimation worked fine except for some synclost errors due to
undocumented errata in OMAP3 which are fixed later and skewed images were seen
on OMAP2 and OMAP3 during horizontal predecimation which will be addressed in
the future patches.

This code is based on code written by Lajos Molnar <lajos@ti.com> who had added
predecimation support for NV12/YUV/rotated/SDMA buffers.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-05-03 16:12:48 +03:00
Archit Taneja
8f366162d2 OMAPDSS: DISPC: Clean up manager timing/size functions
Clean up the DISPC manager timings related function by:

- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-04-23 10:48:10 +03:00
Archit Taneja
c51d921a0c OMAPDSS: DISPC: Use a common function to set manager timings
Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.

We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.

For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-04-23 10:48:10 +03:00
Archit Taneja
e5c09e06a9 OMAPDSS: DISPC/RFBI: Use dispc_mgr_set_lcd_timings() for setting lcd size
The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.

This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-04-23 10:48:09 +03:00
Linus Torvalds
d61b7a572b ARM: global cleanups
Quite a bit of code gets removed, and some stuff moved around, mostly
 the old samsung s3c24xx stuff. There should be no functional changes
 in this series otherwise. Some cleanups have dependencies on other
 arm-soc branches and will be sent in the second round.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUAT2pCjGCrR//JCVInAQLd8RAAqCxhzSc4ewTUP/974gVhujj3TrpiEQcS
 FKvYWF76yP38Lbf3CJZBZaONRtrQNOhYpVQ0jb3WCV4F8mEH9PCes2q9RObeBYiY
 TNX8VdcuVjX2U9HaH0+RQtBUdujNLHpEOqtO57un7T5UDNssR5JOive1tNAooRv1
 pL0Hgx3AVqUbNOPpqQqHzy/MDdd67S6dX80yysANjFGMX87Nvp/ztYAdNnIdta+Z
 pDJt+DPlmK8LvjoSL3SEUN0p3Thk75621cCuauGq88PLIB2w62tzF0NFFbvIAgJT
 3aMlHM2flOiTJAWkUvA8zJiUzwv/0vYvH3xPoTo84abve3lVfZcY+fHNcfxE/Gge
 ri2MmkHyimVP3rNeyM0GbN1RTej1TN1MezeQW3nq2wP6nvS2k0/t32ObLLtWU7XA
 6iA0hKVMSnhqj4ln6jPAmyaDkaWHyYz97urhgetHqGadvLTiGPXCSBPalSiFmyMo
 11tvuqwUNz9tw4nsvGboFQwS2ZoVquC5inoHp5seqZETkGCB67JyeRGxtAM4gbP/
 wIRa3OBLY99yo1on6QovWNnSOMC6X4cOvBI/qHIjSEY/T9JVkslY87gRg3LkxCBR
 XpXfZ6iuLHoSRUGcIjE8D6KHjMgWIDPRnLkIliK4H+3Jn08g0R1MxCplevFCRtis
 egswZ8C24Xw=
 =o5Xl
 -----END PGP SIGNATURE-----

Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull "ARM: global cleanups" from Arnd Bergmann:
 "Quite a bit of code gets removed, and some stuff moved around, mostly
  the old samsung s3c24xx stuff.  There should be no functional changes
  in this series otherwise.  Some cleanups have dependencies on other
  arm-soc branches and will be sent in the second round.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial conflicts mainly due to #include's being changes on
both sides.

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
  ep93xx: Remove unnecessary includes of ep93xx-regs.h
  ep93xx: Move EP93XX_SYSCON defines to SoC private header
  ep93xx: Move crunch code to mach-ep93xx directory
  ep93xx: Make syscon access functions private to SoC
  ep93xx: Configure GPIO ports in core code
  ep93xx: Move peripheral defines to local SoC header
  ep93xx: Convert the watchdog driver into a platform device.
  ep93xx: Use ioremap for backlight driver
  ep93xx: Move GPIO defines to gpio-ep93xx.h
  ep93xx: Don't use system controller defines in audio drivers
  ep93xx: Move PHYS_BASE defines to local SoC header file
  ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
  ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
  PM / devfreq: update the name of EXYNOS clock registers that were omitted
  PM / devfreq: update the name of EXYNOS clock register
  ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
  ARM: EXYNOS: use static declaration on regarding clock
  ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
  ARM: OMAP2+: Fix build error after merge
  ARM: S3C24XX: remove call to s3c24xx_setup_clocks
  ...
2012-03-27 16:03:32 -07:00
Lajos Molnar
08f3267e26 OMAPDSS: DISPC: Fix OMAP4 supported color formats
Add missing but supported color formats for GFX pipeline in dss features:
RGBX16-4444, RGBA16-4444 and XRGB16-1555.

In dispc_ovl_set_color_mode():

- Remove unsupported modes on GFX pipeline: YUV2 and UYVY. Replace these by
  missing modes supported by GFX pipelines: RGBX16-4444 and RGBA16-4444.

- Fix swapped modes on VID pipelines: RGBX16-4444 and XRGB16-4444.

Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-03-06 14:08:16 +02:00
Tony Lindgren
1ca8c07bda ARM: OMAP2+: Drop DISPC L3 firewall code
This is only needed when using SRAM for framebuffer,
and the support for SRAM framebuffer is about to get
removed.

Otherwise we cannot move most of plat/io.h to be a local
iomap.h for mach-omap2.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-02-24 10:34:32 -08:00
Tomi Valkeinen
973b659cbf Merge branch 'work/old-omapfb-removal' 2012-02-23 09:45:58 +02:00
Tomi Valkeinen
2a803c887b OMAPDSS: Remove video SRAM support
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.

This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2012-02-23 09:38:26 +02:00
Archit Taneja
79ee89cdbd OMAPDSS: DISPC: Fix scaling constraints for OMAP4
The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.

Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-02-21 09:39:30 +02:00
Tomi Valkeinen
cd3b34493f OMAPDSS: cleanup probe functions
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.

This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-02-21 09:39:12 +02:00
Tomi Valkeinen
3f60db4bde Merge commit 'v3.3-rc4' 2012-02-21 09:32:19 +02:00
Tomi Valkeinen
0eaf9f52e9 OMAPDSS: use sync versions of pm_runtime_put
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.

Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.

This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
2012-01-26 13:46:24 +02:00
Tomi Valkeinen
5e36097889 Merge branch 'work/fifomerge' 2012-01-25 13:50:34 +02:00
Julia Lawall
6e2a14d2c5 OMAPDSS: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-25 13:48:35 +02:00
Tomi Valkeinen
e0e405b925 OMAPDSS: DISPC: Add naive threshold calc for fifomerge
Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.

This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-25 13:46:20 +02:00
Tomi Valkeinen
83fa2f2e94 OMAPDSS: DISPC: move fifo threhold calc to dispc.c
Move fifo threshold calculation into dispc.c, as the thresholds are
really dispc internal thing.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-25 13:46:19 +02:00
Tomi Valkeinen
3cb5d966e2 OMAPDSS: DISPC: print fifo threshold values in bytes
Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-25 13:46:19 +02:00
Tomi Valkeinen
e6b0f88452 OMAPDSS: FEAT: Add FIFO_MERGE feature
Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.

dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-25 13:46:17 +02:00
Chandrabhanu Mahapatra
7282f1b7c9 OMAPDSS: DISPC: Update Scaling Clock Logic
Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.

So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-02 08:51:29 +02:00
Chandrabhanu Mahapatra
debd90749b OMAPDSS: DISPC: Update Fir Coefficients
The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.

New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.

This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.

Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-02 08:51:29 +02:00
Rob Clark
00f17e4560 OMAPDSS: fix potential NULL pointer ref in OCP_ERR handling path
The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.

Signed-off-by: Rob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-02 08:51:26 +02:00
Tomi Valkeinen
7d1365c998 OMAPDSS: DISPC: add dispc_mgr_get_framedone_irq
Add dispc_mgr_get_framedone_irq() which returns the irq number for
FRAMEDONE for the given channel.

Note that the function returns always 0 for DIGIT channel, even if OMAP4
does have FRAMEDONE_TV interrupt. The reason for this is that this
function is currently used only to track manual updates, and thus
FRAMEDONE_TV is not needed.

If there's need in the future to also get the FRAMEDONE_TV this needs
revisiting. However, as FRAMEDONE_TV doesn't exist on OMAP2/3, the use
of this function for that purpose needs some extra code to handle the
OMAP2/3 case.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:45 +02:00
Tomi Valkeinen
3dcec4d6ba OMAPDSS: DISPC: Add dispc_mgr_get_vsync_irq()
Add dispc_mgr_get_vsync_irq() which returns the irq number for vsync on
the given channel.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:36 +02:00
Tomi Valkeinen
c3f96fee1e OMAPDSS: DISPC: remove unused functions
Remove unused functions:

dispc_mgr_get_default_color
dispc_mgr_get_trans_key
dispc_mgr_trans_key_enabled
dispc_mgr_alpha_fixed_zorder_enabled

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:28 +02:00
Tomi Valkeinen
c64dca40c5 OMAPDSS: setup manager with dispc_mgr_setup()
Change manager configuration to be similar to overlay configuration by
creating dispc_mgr_setup() which takes omap_overlay_manager_info as
parameter.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:27 +02:00
Tomi Valkeinen
2cc5d1af5a OMAPDSS: separate overlay channel from ovl_setup
Overlay channel is configured with ovl_setup, with all the other overlay
attriutes. This patch separates overlay channel setup so that we can
later configure the channel only when needed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:26 +02:00
Tomi Valkeinen
f38545da53 OMAPDSS: separate FIFO threshold setup from ovl_setup
Overlay FIFO thresholds are configured with ovl_setup, with all the
other overlay attributes. This patch separates FIFO threshold setup so
that we can later configure FIFO thresholds only when needed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:26 +02:00
Tomi Valkeinen
cf0736681e OMAPDSS: DISPC: handle 0 out_width/out_height in ovl_setup()
Overlay out_width/height are set to 0 when scaling is not used by the
users of omapdss. Currently ovl_setup() expects the caller of
ovl_setup() to convert those zero values to width or height.

This patch makes ovl_setup() accept zero values for out_width/height,
making calling ovl_setup() a bit simpler as the overlay_info can be
just passed to this function without modifications.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:25 +02:00
Tomi Valkeinen
6f04e1bfc3 OMAPDSS: DISPC: make dispc_ovl_set_fifo_threshold() public
Make dispc_ovl_set_fifo_threshold() public so that later patches can
handle overlay fifo configuration.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:22 +02:00
Tomi Valkeinen
f427984e89 OMAPDSS: DISPC: make dispc_ovl_set_channel_out() public
Make dispc_ovl_set_channel_out() public so that later patches can handle
changing overlay's manager.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:22 +02:00
Tomi Valkeinen
b6a44e7748 OMAPDSS: DISPC: Flush posted writes when enabling outputs
Flush posted write in _enable_lcd_out() and _enable_digit_out(). This
ensures the the lcd/digit bit is written before the code starts waiting
for interrupts about enabling/disabling the output.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02 08:54:14 +02:00
Tomi Valkeinen
f95cb5ebd8 OMAPDSS: DISPC: skip scaling calculations when not scaling
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.

This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:

omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz

A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-11-18 10:09:17 +02:00
Paul Gortmaker
a8a3593185 video: Add export.h for THIS_MODULE/EXPORT_SYMBOL to drivers/video
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:33 -04:00
Archit Taneja
54128701ec OMAPDSS: DISPC: zorder support for DSS overlays
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.

Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.

Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:55 +03:00
Archit Taneja
b8c095b4d6 OMAPDSS: DISPC: VIDEO3 pipeline support
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:54 +03:00
Archit Taneja
11354dd58d OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.

Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.

Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.

Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.

Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03 16:51:54 +03:00
Archit Taneja
0373cac6cc OMAPDSS: FEATURES: Create a range param to get max downscaling
Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:27 +03:00
Archit Taneja
79ad75f27b OMAPDSS: DISPC: Clean up scaling related clock and five tap calculations
Move DISPC scaling related code from dispc_ovl_setup() to a new function
dispc_ovl_calc_scaling(). Use overlay caps to check if the overlay can scale or
not. No functional changes are made.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:26 +03:00
Archit Taneja
ebdc52499f OMAPDSS: DISPC: Remove hardcoded use of PPL in five tap clock calculation
The function calc_fclk_five_taps() uses a fixed value of pixels per line which
is used in calculations to get the minimum fclk needed for scaling with five
taps to work.

Remove this by providing the width of the panel connected to the manager.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:26 +03:00
Archit Taneja
c3dc6a7afb OMAPDSS: DISPC: Get correct pixel clock for TV manager
dispc_mgr_pclk_rate() is used to calculate minimum required functional clock for
scaling in calc_fclk() and calc_fclk_five_taps(). This function returns the
correct pixel clock for LCD and LCD2 managers, but not for TV manager. Extend
this function so that it gets the correct pixel clock for TV manager.

This also prevents the crash we get when we try to scale overlays connected to
TV manager. The current code leads to a BUG() being executed if we call
dispc_mgr_pclk_rate() for the TV manager.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:25 +03:00
Archit Taneja
dac57a05fc OMAPDSS: DISPC: Create helper function dispc_mgr_is_lcd()
Create a helper function called dispc_mgr_is_lcd() which returns true if the
manager is LCD or LCD2.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:25 +03:00
Archit Taneja
c3d92529c3 OMAPDSS: DISPC: Pass overlay params as arguments to dispc_ovl_setup()
dispc_ovl_enable_replication() and dispc_ovl_set_fifo_threshold() are currently
called in configure_overlay(). These are the only functions which cause DISPC
register writes of overlay parameters outside of dispc_ovl_setup().

Move these to dispc_ovl_setup() and pass replication, fifo_low and fifo_high
thresholds as arguments to dispc_ovl_setup() in order to be aligned with other
overlay parameters. No functional changes are made.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:25 +03:00
Archit Taneja
a4273b7cca OMAPDSS: DISPC: Reduce the number of arguments in dispc_ovl_setup()
dispc_ovl_setup() currently takes a large number of overlay arguments, most of
these are members of the overlay_info struct. Replace these arguments by
passing a overlay_info pointer instead.

In configure_overlay(), we create an overlay_info struct called new_oi, this is
a copy of the overlay cache's overlay_info member. Update the new_oi parameters
which could have been possibly changed in configure_overlay(). Pass its pointer
pointer to dispc_ovl_setup().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:17:24 +03:00
Tomi Valkeinen
e82b090b80 OMAP: DSS2: DISPC: improve dispc_mgr_enable_digit_out()
dispc_mgr_enable_digit_out() didn't handle HDMI case very well.

Improve the function to use FRAMEDONETV interrupt to see when HDMI has
been disabled.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:43 +03:00
Tomi Valkeinen
9eaaf2076d OMAP: DSS2: DISPC: Fix minimum PCD value
The current driver had a hardcoded minimum value of 2 for pixel clock
divisor (PCD). This doesn't seem to be right.

OMAP4 TRM says that PCD can be 1 when not downscaling, and inverted
pixel clock (IPC) is off.

OMAP3 TRM says the same, but also in the register descriptions that PCD
value 1 is invalid.

OMAP2 TRM says PCD 2 is the minimum.

OMAP2 is still untested, but for both OMAP3 and OMAP4 PCD of 1 seems to
work fine.

This patch adds a new DSS feature, FEAT_PARAM_DSS_PCD, which is used to
find the minimum and maximum PCD. The minimum is set to 2 for OMAP2, and
1 for OMAP3/4.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:35 +03:00
Archit Taneja
569969d601 OMAP: DSS2: Clean up stallmode and io pad mode selection
Split the function dispc_set_parallel_interface_mode() into 2 separate
functions called dispc_mgr_set_io_pad_mode() and dispc_mgr_enable_stallmode().
The current function tries to set 2 different modes(io pad mode and stall mode)
based on a parameter omap_parallel_interface_mode which loosely corresponds to
the panel interface type.

This isn't correct because a) these 2 modes are independent to some extent,
b) we are currently configuring gpout0/gpout1 for DSI panels which is
unnecessary, c) a DSI Video mode panel won't get configured correctly.

Splitting the functions allows the interface driver to set these modes
independently and hence allow more flexibility.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:28 +03:00
Tomi Valkeinen
26d9dd0dbe OMAP: DSS2: DISPC: rename manager related funcs
Rename dispc's manager related functions as follows:

- Remove prepending underscores, which were originally used to inform
  that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_mgr_*
- Remove "channel" from the name, e.g. dispc_enable_channel ->
  dispc_mgr_enable

The idea is to group manager related functions so that it can be deduced
from the function name that it writes to manager spesific registers.

All dispc_mgr_* functions have enum omap_channel as the first parameter.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:23 +03:00
Tomi Valkeinen
f0e5caab97 OMAP: DSS2: DISPC: rename overlay related funcs
Rename dispc's overlay related functions as follows:

- Remove prepending underscores, which were originally used to inform
  that the clocks needs to be enabled. This meaning is no longer valid.
- Prepend the functions with dispc_ovl_*
- Remove "plane" from the name, e.g. dispc_set_plane_ba0 ->
  dispc_ovl_set_ba0

The idea is to group overlay related functions so that it can be deduced
from the function name that it writes to overlay spesific registers.

All dispc_ovl_* functions have enum omap_plane as the first parameter.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:23 +03:00
Tomi Valkeinen
f6dc815098 OMAP: DSS2: Add GLOBAL_ALPHA & PRE_MULT_ALPHA to ovl caps
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.

Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
2011-09-30 16:16:21 +03:00
Tomi Valkeinen
fe3cc9d6cd OMAP: DSS2: DISPC: use lookup tables for bit shifts
Use lookup tables instead of switch/if in some DISPC functions to make
the code cleaner.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
2011-09-30 16:16:20 +03:00
Tomi Valkeinen
4a9e78abb7 OMAP: DSS2: Remove support for non-DISPC overlays
Remove support for non-DISPC overlays and overlay managers.

The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:

- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
  update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
  omapdss driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
2011-09-30 16:16:20 +03:00
Tomi Valkeinen
8fa8031c54 OMAP: DSS2: Handle manager change in apply
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.

Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().

A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30 16:16:19 +03:00
Tomi Valkeinen
f36465822d OMAP: DSS2: remove unneeded fck enable/disables
Now that the HWMOD fmwk handles the fcks of DSS modules properly, the
DSS driver no longer needs to explicitely enable/disable the fck.

This patch removes the enables/disables of fck from dispc, dsi and dss.
The clk_get(fck) is still needed there, as the modules need to know the
frequency of the clock.

For hdmi and venc this patch also removes the clk_get(fck), as they
don't need the clock at all.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-20 11:21:31 +03:00
Archit Taneja
e13a138bc6 OMAP: DSS2: Use a macro to declare size of the fifo_size array in dispc.c
The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Archit Taneja
ac01c29e52 OMAP: DSS2: DISPC: Shorten _dispc_set_color_conv_coef()
Iterate over overlay id's to shorten _dispc_set_color_conv_coef()

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Archit Taneja
c6104b8e24 OMAP: DSS2: DISPC: dispc_save_context() and dispc_restore_context() cleanup
Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Archit Taneja
4dd2da15fc OMAP: DSS2: DISPC: Shorten dispc_dump_regs()
Iterate over manager and overlay id's to shorten dispc_dump_regs().

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Archit Taneja
5010be8012 OMAP: DSS2: DISPC: Prepare dispc_dump_regs() for shortening
Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).

Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Dima Zavin
13eae1f982 OMAP: DSS: dispc: enable/disable clocks in error handler
There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.

Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-14 18:08:24 +03:00
Tomi Valkeinen
49ea86f3fa OMAP: DSS2: DISPC: Fix context save/restore
The current method of saving and restoring the context could cause a
restore before saving, effectively "restoring" zero values to registers.

Add ctx_valid field to indicate if the saved context is valid and can be
restored.

Also restructure the code to save the ctx_loss_count in save_context(),
which makes more sense than the previous method of storing new
ctx_loss_count in dispc_need_ctx_restore.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:07 +03:00
Tomi Valkeinen
e6d80f950a OMAP: DSS2: DISPC: remove finegrained clk enables/disables
dispc.c enables and disables clocks in almost every function to make
sure the clocks are enabled when the function is called. This is rather
unoptimal way to handle the problem.

With pm_runtime other components have to call dispc_runtime_get() to
enable dispc clocks before calling any other dispc functions. Thus the
finegrained clk enables/disables can be removed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:05 +03:00
Tomi Valkeinen
4fbafaf371 OMAP: DSS2: Use PM runtime & HWMOD support
Use PM runtime and HWMOD support to handle enabling and disabling of DSS
modules.

Each DSS module will have get and put functions which can be used to
enable and disable that module. The functions use pm_runtime and hwmod
opt-clocks to enable the hardware.

Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25 10:22:04 +03:00
Tomi Valkeinen
5ed8cf5b8e OMAP: DSS2: Fix FIFO threshold and burst size for OMAP4
The DMA FIFO threshold registers and burst size registers have changed
for OMAP4.  The current code only handles OMAP2/3 case, and so the
values are a bit off for OMAP4.  A summary of the differences between
OMAP2/3 and OMAP4:

Burst size:
OMAP2/3: 4 x 32 bits / 8 x 32 bits / 16 x 32 bits
OMAP4: 2 x 128 bits / 4 x 128 bits / 8 x 128 bits

Threshold size:
OMAP2/3: in bytes (8 bit units)
OMAP4: in 128bit units

This patch fixes the issue by creating two new helper functions in
dss_features: dss_feat_get_buffer_size_unit() and
dss_feat_get_burst_size_unit(). These return (in bytes) the unit size
for threshold registers and unit size for burst size register,
respectively, and are used to calculate correct values.

For the threshold size the usage is straightforward. However, the burst
size register has different multipliers for OMAP2/3 and OMAP4. This
patch solves the problem by defining the multipliers for the burst size
as 2x, 4x and 8x, which fit fine for the OMAP4 burst size definition
(i.e. burst size unit for OMAP4 is 128bits), but requires a slight twist
on OMAP2/3 by defining the burst size unit as 64bit.

As the driver in practice always uses the maximum burst size, and no use
case currently exists where we would want to use a smaller burst size,
this patch changes the driver to hardcode the burst size when
initializing DISPC. This makes the threshold configuration code somewhat
simpler.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:07:14 +03:00
Tomi Valkeinen
3c07cae2cc OMAP: DSS2: Add Color Phase Rotation support
Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and
to set the CPR coefficient matrix.

CPR is enabled via manager?/cpr_enable file, and the coefficient matrix
is set via manager?/cpr_coef file. The values in cpr_coef are in the
following order:

RR RG RB GR GG GB BR BG BB

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:07:13 +03:00
Tomi Valkeinen
332e9d7051 OMAP: DSS2: Add new FEAT definitions for features missing from OMAP2
OMAP2 doesn't have CPR, PRELOAD nor FIR_COEF_V registers. Add new
feature definitions for those, and check the feature before accessing
those registers.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:06:49 +03:00
Tomi Valkeinen
24e6289c02 OMAP: DSS2: remove extra includes from include/video/omapdss.h
omapdss.h included platform_device.h and atomic.h, neither of which is
needed by omapdss.h. Remove those includes from omapdss.h, and fix the
affected .c files which did not include platform_device.h even though
they should.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01 12:01:12 +03:00
Amber Jain
0d66cbb53e OMAP: DSS2: Add support for NV12 format
Add the support for NV12 color format.
Configure base address for UV component of NV12 color format.
Change the way chroma scaling is handled for YUV formats on OMAP4 by enabling
chroma-resampling for video pipeline and hence using FIR2 register set for
scaling UV.
Changes to _dispc_set_scaling(), because of the reason above, are:
- call _dispc_set_scaling_common() to handle scaling for all color formats
  except for OMAP4 where it only handles scaling for RGB or Y-component
- call _dispc_set_scaling_uv() for special handling required for UV
  component on OMAP4.
- dispc_set_scaling_uv() also resets chroma-resampling bit for RGB color modes.

Contains chroma scaling (_dispc_set_scaling_uv) design and implemented by
Lajos Molnar <molnar@ti.com>

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Amber Jain
ab5ca071e2 OMAP: DSS2: Add new registers for NV12 support
Add new registers specific to UV color component that are introduced in OMAP4.
Add simple helper functions to configure the newly added registers.
These new registers are mainly:
- UV base address registers used specifically for NV12 color-format
- FIR registers used for UV-color-component scaling on OMAP4
- Accumulator registers used for UV-color-component scaling
Add these new registers to save/restore and DUMPREG functions.
Also add two new features for OMAP4:
- FEAT_HANDLE_UV_SEPARATE - this is used on OMAP4 as UV color-component requires
  separate handling.
- FEAT_ATTR2 - this is used on OMAP4 to configure new ATTRIBUTES2 register.

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Amber Jain
5719d35cce OMAP: DSS2: Use for loop where ever possible in SR(), RR()
Use for loop instead of individual entries for OVL_FIR_COEF_H, OVL_FIR_COEF_HV,
OVL_FIR_COEF_V and OVL_CONV_COEF in SR() and  RR().

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Amber Jain
ed14a3ce98 OMAP: DSS2: Ensure non-zero FIR values are configured
FIR values can never be zero as per TRM, and the current code writes zero
when scaling is not used. It was not causing any problem as scaling was
disabled when zero was written. Its still safer to not write zero to
it in any case.
Now we configure correct FIR values even when scaling is not used (i.e. set FIR
to 1024 when scaling is not used), but the scaling enable bits are still kept
off if the scaling is not needed.

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Amber Jain
f20e42205a OMAP: DSS2: Add new color formats for OMAP4
Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16,
ARGB16_1555, XRGB16_1555.
NV12 color format is defined here, its support in DSS will be added separately.

Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23 08:29:47 +03:00
Archit Taneja
5a8b572d83 OMAP4: DSS2: DSI: Changes for DSI2 on OMAP4
Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol
engine and DISPC Functional clock. Do the following:

- Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the
  dsi module number as an argument.
- Create debugfs files for dsi2, split the corresponding debugfs functions.
- Allow DPI to use these new clock sources.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:30:27 +03:00
Archit Taneja
a72b64b999 OMAP: DSS2: Pass platform_device as an argument in dsi functions
The DSI interface is represented as a platform device, using the DSI platform
driver(dsi.c). The current DSI driver design is capable of running only one
instance of a DSI device. On OMAP4, there are 2 very similar DSI modules which
can be represented as instances of "omapdss_dsi" platform device.

Add member "module" in "dssdev.phy.dsi" that tells us which DSI module's lanes
the panel is connected to. Modify dsi.c functions to take the device's
platform_device struct pointer, provide functions dsi_get_dsidev_from_dssdev()
and dsi_get_dsidev_from_id() take the panel's omap_dss_device and module number
respectively, and return the platform_device pointer. Currently, the dsi struct
is declared globally and is accessed when dsi data is needed. The new pdev
argument will be used later to provide the platform device's dsi related data.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12 19:30:26 +03:00
Archit Taneja
55978cc20e OMAP: DSS2: Remove usage of struct dispc_reg
struct dispc_reg was originally used while migrating from old omapfb to
catch cases where the arguments to dispc_read_reg/dispc_write_reg were in
wrong order, since old omapfb had the arguments in reverse order.

Remove this struct and use u16 instead

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:53 +03:00
Archit Taneja
702d144845 OMAP: DSS2: Clean up DISPC overlay manager register definitions
Represent manager/channel specific DISPC registers as inline functions returning
the required dispc_reg struct. This is done since the current method is not
scalable as the number of overlay managers increase in number.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:52 +03:00
Archit Taneja
9b372c2d9d OMAP: DSS2: Clean up DISPC overlay register definitions
Move all DISPC register definitions to a new header dispc.h. There are
separate register offset definitions for GFX, VID1 and VID2 pipeline share
register definitions by using an argument. The introduction of VID3 pipeline
on OMAP4 will not let us use the above method since VID3 pipe register offsets
don't map with VID1 and VID2 offsets.

Represent overlay registers as DISPC_OVL_XXXX(plane), where the plane argument
tells the overlay. Register offsets are calculated as:

DISPC_OVL_XXXX(plane) = DISPC_OVL_BASE(plane) + DISPC_XXXX_OFFSET(plane)

Idea suggested by Tomi Valkeinen.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:20:52 +03:00
Archit Taneja
89a35e5170 OMAP2PLUS: DSS2: Change enum "dss_clk_source" to "omap_dss_clk_source"
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:19:27 +03:00
Tomi Valkeinen
a0b38cc4d3 OMAP: DSS2: Move display.h to include/video/
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11 14:05:07 +03:00
Mythri P K
d3862610c9 OMAP4: DSS2: HDMI: Dispc gamma enable set/reset function for TV.
Adding function to reset/set gamma table bit for TV interface, currently
only support for disabled is added.

Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-16 11:45:49 +05:30
Taneja, Archit
ea75159ee6 OMAP4: DSS2: Clock source changes for OMAP4
On OMAP3, the pixel clock for the LCD manager was derived through DISPC_FCLK as:

Lcd Pixel clock = DISPC_FCLK / lcd / pcd

Where lcd and pcd are divisors in the DISPC_DIVISOR register.

On OMAP4, the pixel clocks for LCD1 and LCD2 managers are derived from 2 new
clocks named LCD1_CLK and LCD2_CLK. The pixel clocks are calculated as:

Lcd_o Pixel clock = LCDo_CLK / lcdo /pcdo, o = 1, 2

Where lcdo and pcdo registers are divisors in DISPC_DIVISORo registers.

LCD1_CLK and LCD2_CLK can have DSS_FCLK, and the M4 divider clocks of DSI1 PLL
and DSI2 PLL as clock sources respectively. Introduce functions to select and
get the clock source for these new clocks. Modify DISPC functions get the
correct lck and pck rates based on the clock source of these clocks. Since
OMAP2/3 don't have these clocks, force OMAP2/3 to always have the LCD_CLK source
as DSS_CLK_SRC_FCK by introducing a dss feature.

Introduce clock source names for OMAP4 and some register field changes in
DSS_CTRL on OMAP4.

Currently, LCD2_CLK can only have DSS_FCLK as its clock source as DSI2 PLL
functionality hasn't been introduced yet. BUG for now if DSI2 PLL is selected as
clock.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:31 +02:00
Taneja, Archit
66534e8e93 OMAP2PLUS: DSS2: Cleanup clock source related code
Clean up some of the DSS functions which select/get clock sources, use switch
to select the clock source members since more clock sources will be introduced
later on.

Remove the use of macro CONFIG_OMAP2_DSS_DSI in dispc_fclk_rate, use a dummy
inline for function for dsi_get_pll_hsdiv_dispc_rate() instead for code clarity.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:30 +02:00
Tomi Valkeinen
b9cb0984a6 OMAP: DSS2: fix omap_dispc_register_isr() fail path
Fix handling of error in omap_dispc_register_isr() in case there are no
free isr slots available.

Reported-by: Ben Tucker <btucker@mpcdata.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:30 +02:00
Murthy, Raghuveer
0cf35df353 OMAP4: DSS2: Using dss_features to set independent core clock divider
Using dss_features to select independent core clock divider and setting
it. Added the register used, to DISPC context save and restore group

-----------------------------------------------------------------------
In OMAP4, the minimum DISPC_CORE_CLK required can be expressed as:

	DISPC_CORE_CLK >= max(PCLK1*HSCALE1, PCLK2*HSCALE2, ...)

Where PCLKi is the pixel clock generated by MANAGERi and HSCALEi is the
maximum horizontal downscaling done through MANAGERi

Based on the usecase, core clk can be increased or decreased at runtime
to save power. Such mechanism are not yet implemented. Hence, we set the
core clock divisor to 1, to support maximum range of resolutions
------------------------------------------------------------------------

Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:29 +02:00
Murthy, Raghuveer
ce7fa5eb1e OMAP: DSS2: Renaming register macro DISPC_DIVISOR(ch)
The OMAP4 DISPC_DIVISOR1 is backward compatible to OMAP3xxx DISPC_DIVISOR.
However DISPC_DIVISOR is also provided in OMAP4, to control DISPC_CORE_CLK
independent of Primary and Secondary display clocks.

Renamed DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch), to facilitate introduction
of DISPC_DIVISOR register, which is specific for OMAP4. OMAP4 has 3 registers
DISPC_DIVISOR, DISPC_DIVISOR1 and DISPC_DIVISOR2.

Also updated, all the usages of DISPC_DIVISOR(ch) to DISPC_DIVISORo(ch).
Use DISPC_DIVISORo(ch) when DISPC_DIVISOR1 or DISPC_DIVISOR2 has to be
configured

OMAP4 TRM uses DISPC_DIVISORo generically to refer to DISPC_DIVISOR1 and
DISPC_DIVISOR2

Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:29 +02:00
Archit Taneja
1bb4783506 OMAP2PLUS: DSS2: DSI: Generalize DSI PLL Clock Naming
DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.

dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.

Functions and macros named on the basis of these clock names have also been
made generic.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:27 +02:00
Archit Taneja
067a57e48e OMAP2PLUS: DSS2: Use dss features to get clock source names of current OMAP
Clock source names vary across OMAP2/3 and OMAP4, the clock source enum
names have been made generic in the driver, but for purposes of debugging
and dumping clock sources, it is better to preserve the actual TRM name of
the clock.

Introduce a dss feature function 'dss_feat_get_clk_source_name()' which
returns a string with the TRM clock name for the current OMAP in use. The OMAP
specific name is printed along the generic name within brackets.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:27 +02:00
Archit Taneja
88134fa138 OMAP2PLUS: DSS2: Make members of dss_clk_source generic
The enum members of 'dss_clk_source' have clock source names specific to
OMAP2/3. Change the names to more generic terms such that they now describe
where the clocks come from and what they are used for.

Also, change the enum member names to have "DSS_CLK_SRC" instead of "DSS_SRC"
for more clarity.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:27 +02:00
Archit Taneja
87a7484b6a OMAP2PLUS: DSS2: FEATURES: DISPC overlay code cleanup
Add dss_features and register fields to incorporate changes in DISPC pipelines
between OMAP3 and OMAP4.

Register fields added: FEAT_REG_HORIZONTALACCU, FEAT_REG_VERTICALACCU
DSS Features added: FEAT_LINEBUFFERSPLIT, FEAT_ROWREPEATENABLE, FEAT_RESIZECONF

_dispc_set_scaling() and _dispc_set_rotation_attrs() have been cleaned up.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:26 +02:00
archit taneja
affe360d13 OMAP: DSS2: Have separate irq handlers for DISPC and DSI
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.

On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.

On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.

Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.

Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.

The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:24 +02:00
Archit Taneja
6af9cd1431 OMAP2PLUS: DSS2: Generalize naming of PRCM related clock enums in DSS driver
enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:22 +02:00
Senthilvadivu Guruswamy
ea9da36a30 OMAP2,3: DSS2: Use platform device to get baseaddr
DSS, DISPC, DSI, RFBI, VENC baseaddr can be obtained from platform_get_resource().
This API in turn picks the right silicon baseaddr from the hwmod database.
So hardcoding of base addr could be removed.

Reviewed-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:21 +02:00
Sumit Semwal
a06b62f800 OMAP2,3: DSS2: replace printk with dev_dbg in init
This patch replaces printk's in the init/probe functions to dev_dbg
for boot time optimization.

Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:21 +02:00
Senthilvadivu Guruswamy
060b6d9cba OMAP2, 3: DSS2: DISPC: create platform_driver, move init, exit to driver
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DISPC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

DISPC platform driver is registered from inside omap_dss_probe, in the order desired.

Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:20 +02:00
Sumit Semwal
18faa1b68a OMAP: DSS2: Introduce omap_channel as an omap_dss_device parameter, add new overlay manager.
A panel connects to one of the overlay managers of DSS through some interface block.
On OMAP4, specifying the type of the display is not sufficient to conclude which manager
the panel should be connected to.
Hence, a new member 'channel' is introduced in omap_dss_device structure to determine
which manager the panel uses. The dss_recheck_connections() called in dss_driver_probe()
uses this channel parameter to set the correct manager to the corresponding omap_dss_device.

The channel parameter is used only once to ensure the correct managers are set for each
panel. The parameter dssdev->manager->id will take care of ensuring that the panel and
then the interface driver configures the correct DISPC channel.

Also, add a new Overlay Manager in manager.c, make other changes needed for LCD2 channel.

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:36:51 +02:00
Archit Taneja
6ced40bfc0 OMAP: DSS2: Use dss_features to handle DISPC bits removed on OMAP4
DISPC_CONFIG bits LCDENABLEPOL, LCDENABLESIGNAL, PCKFREEENABLE and FUNCGATED
have been removed from OMAP4, use dss_features to handle them correctly.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:36:50 +02:00
Sumit Semwal
2a205f34b8 OMAP: DSS2: LCD2 Channel Changes for DISPC
DISPC functions are modified in order to work when the manager is LCD2.
This includes:
Adding new IRQs specific to LCD2 and their handling.
Provide dumps of the new manager's registers.
Provide dumps of the new manager's clocks.
Checks for channel for registers DISPC_CONTROL2 and DISPC_CONFIG2
which can't be parametrized.

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:36:49 +02:00
Sumit Semwal
ff1b2cde3f OMAP: DSS2: Change remaining DISPC functions for new omap_channel argument
The following dispc functions are also changed to incorporate channel as an argument:
	-dispc_lclk_rate()
	-dispc_pclk_rate()
	-dispc_set_pol_freq()
	-dispc_set_clock_div()
	-dispc_get_clock_div()

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:36:34 +02:00
Sumit Semwal
64ba4f748a OMAP: DSS2: Introduce omap_channel argument to DISPC functions used by interface drivers
The interface drivers (dsi.c, sdi.c etc) need to call dispc functions with
dssdev->manager->id as a parameter to specify the DISPC channel which they want
to configure/use, this is required as the same functions are now used to configure
dispc registers of different channels.

The following dispc functions are changed to incorporate channel as an argument:
	-dispc_enable_fifohandcheck()
	-dispc_set_lcd_size()
	-dispc_set_parallel_interface_mode()
	-dispc_set_tft_data_lines()
	-dispc_set_lcd_display_type()
	-dispc_set_lcd_timings()

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:35:59 +02:00
Sumit Semwal
8613b0005d OMAP: DSS2: Represent DISPC register defines with channel as parameter
On OMAP4, we have a new DISPC channel for Overlay Manager LCD2. There is a set
of regsiters for LCD2 channel similar to the existing LCD channel, like
DISPC_CONTROL2, DISPC_DIVISOR2, DISPC_CONFIG2 and so on.

Introduce new enum members for LCD2 Channel and corresponding Overlay Manager
in display.h.

Represent the following DISPC register defines with channel as a parameter
to differentiate between LCD and LCD2 registers (and also DIGIT in some cases):

DISPC_DEFAULT_COLOR, DISPC_TRANS_COLOR, DISPC_TIMING_H, DISPC_TIMING_V,
DISPC_POL_FREQ, DISPC_DIVISOR, DISPC_SIZE_LCD, DISPC_DATA_CYCLEk,
DISPC_CPR_COEF_R, DISPC_CPR_COEF_G and DISPC_CPR_COEF_B

This parametrization helps in reducing the number of register defines for DISPC.
Replace the existing reads/writes to these registers in this new way.
Also, Introduce defines for registers DISPC_CONTROL2 and DISPC_CONFIG2 which
are used exclusively for LCD2 channel.

Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:09:54 +02:00
Archit Taneja
8dad2ab672 OMAP: DSS2: Clean up DISPC color mode validation checks
The supported set of color modes varies for different DISPC pipelines(plane)
and omap version. This makes the checks for validation of a color mode more
complicated as new omap versions are added.

A dss_feature function is created which tells if a color_mode is supported
for a plane on the current omap revision.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 11:09:54 +02:00
Rajkumar N
fd28a39071 OMAP3630: DSS2: Enable Pre-Multiplied Alpha Support
Enable dss to process color formats with pre-mulitplied alpha.
With this we can have alpha values defined for each pixel
and hence can have different blending values for each pixel.
sysfs entry has been created for this and pre-multiplied alpha
support is turned off by default.

Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Rajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: Samreen <samreen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 10:54:19 +02:00
Archit Taneja
712247a681 OMAP: DSS2: Fix: Read correct bit in dispc_enable_alpha_blending()
Read correct DISPC_CONFIG bit when the channel is DIGIT, remove extra line
at the end of the function.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2011-01-10 10:54:18 +02:00
Archit Taneja
a0acb5574b OMAP: DSS2: Use dss_features framework on DSS2 code
Calls init functions of dss_features during dss_probe, and the following
features are made omapxxxx independent:
  - number of managers, overlays
  - supported color modes for each overlay
  - supported displays for each manager
  - global aplha, and restriction of global alpha for video1 pipeline
  - The register field ranges : FIRHINC, FIRVINC, FIFOHIGHTHRESHOLD
    FIFOLOWTHRESHOLD and FIFOSIZE

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-10-22 23:21:04 +03:00
Grazvydas Ignotas
66be8f6cec OMAP: DSS2: make filter coefficient tables human readable
Reorganize scaler FIR filter data as FIR value tables from raw
register values. This makes them easier to understand and simplifies
register programming code.

No functional changes.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-09-29 10:34:46 +03:00
Tomi Valkeinen
ab83b14c82 OMAP: DSS2: DSI: use BTA to end the frame transfer
Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.

This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.

This will give us much better latency to handle the end of the frame
than with the previous work based solution.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-05 16:52:02 +03:00
Ville Syrjälä
75c7d59daf OMAP: DSS2: clear spurious SYNC_LOST_DIGIT interrupts
When DSS transitions from off mode to on VENC may generate a spurious
SYNC_LOST_DIGIT error. Just ack it when restoring the context. Also
restore IRQENABLE last to avoid triggering interrupts before the
context is fully restored.

Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03 15:18:45 +03:00
Tomi Valkeinen
37ac60e414 OMAP: DSS2: move enable/disable/suspend/resume
Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-24 14:31:28 +02:00
Tomi Valkeinen
a2faee84f6 OMAP: DSS2: move enable/disable_channel to overlay manager
Move enable/disable_channel() from omap_dss_device to overlay manager.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-24 14:31:27 +02:00
Tomi Valkeinen
63cf28ac3e OMAP: DSS2: fix get_dsi/dispc_clk_source() usage
After changing the selection of DSI and DISPC clock source the users of
get_dsi/dispc_clk_source() functions were left unchanged.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-23 17:43:39 +02:00
Tomi Valkeinen
853525d778 OMAP: DSS2: fix irq-stats compilation
Fix compilation of the CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS feature.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-15 15:14:39 +02:00
Ville Syrjälä
2d9c5597ad OMAP: DSS2: Reject scaling settings when they cannot be supported
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.

Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-12 12:10:19 +02:00
Tomi Valkeinen
dfc0fd8d88 OMAP: DSS2: Collect interrupt statistics
Collect interrupt statistics, printable via debugfs:

debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq

The counters are reset when printed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-08 15:32:18 +02:00
Tomi Valkeinen
80c397120f OMAP: DSS2: DISPC
This file implements DISPC (display controller) block of the OMAP DSS.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2009-12-09 12:04:35 +02:00