This is the initial implementation of the new OGM protocol
(version 2). It has been designed to work on top of the
newly added ELP.
In the previous version the OGM protocol was used to both
measure link qualities and flood the network with the metric
information. In this version the protocol is in charge of
the latter task only, leaving the former to ELP.
This means being able to decouple the interval used by the
neighbor discovery from the OGM broadcasting, which revealed
to be costly in dense networks and needed to be relaxed so
leading to a less responsive routing protocol.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This parameter can be set individually on each interface and
allows the configuration of the elp interval for the link
quality measurements during runtime. Usually it is desirable
to set it to a higher (= slower) value on interfaces which
have a more static characteristic (e.g. wired interfaces)
or very dense neighbourhoods to reduce overhead.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: respin on top of the latest master]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Initially developed by Linus during a 6 months trainee study
period in Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
The B.A.T.M.A.N. protocol originally only used a single
message type (called OGM) to determine the link qualities to
the direct neighbors and spreading these link quality
information through the whole mesh. This procedure is
summarized on the BATMAN concept page and explained in
details in the RFC draft published in 2008.
This approach was chosen for its simplicity during the
protocol design phase and the implementation. However, it
also bears some drawbacks:
* Wireless interfaces usually come with some packet loss,
therefore a higher broadcast rate is desirable to allow
a fast reaction on flaky connections.
Other interfaces of the same host might be connected to
Ethernet LANs / VPNs / etc which rarely exhibit packet
loss would benefit from a lower broadcast rate to reduce
overhead.
* It generally is more desirable to detect local link
quality changes at a faster rate than propagating all
these changes through the entire mesh (the far end of
the mesh does not need to care about local link quality
changes that much). Other optimizations strategies, like
reducing overhead, might be possible if OGMs weren't
used for all tasks in the mesh at the same time.
As a result detecting local link qualities shall be handled
by an independent message type, ELP, whereas the OGM message
type remains responsible for flooding the mesh with these
link quality information and determining the overall path
transmit qualities.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
This allows us to easily add a sysfs parameter for an
unsigned int later, which is not for a batman mesh interface
(e.g. bat0), but for a common interface instead. It allows
reading and writing an atomic_t in hard_iface (instead of
bat_priv compared to the mesh variant).
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: rename functions and move macros]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
BATADV_BONDING_TQ_THRESHOLD is not used anymore since the implementation
of the bat_neigh_is_similar_or_better() API function.
Such function uses the more generic BATADV_TQ_SIMILARITY_THRESHOLD
constant.
Therefore, remove definition of the unused BATADV_BONDING_TQ_THRESHOLD
constant.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
INFO: rcu_sched self-detected stall on CPU
1: (5264 ticks this GP) idle=3e9/140000000000001/0
softirq=144683/144686 fqs=5249
(t=5250 jiffies g=46 c=45 q=43)
Task dump for CPU 1:
insmod R running task 0 247 245 0x00000008
ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140
0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001
ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001
Call Trace:
<IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0
[<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0
[<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180
[<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50
[<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60
[<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90
[<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90
<EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40
[<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv]
[<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0
[...]
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: rewritten description, extracted fix]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batadv_orig_node_vlan reference counter in batadv_tt_global_size_mod
can only be reduced when the list entry was actually removed. Otherwise the
reference counter may reach zero when batadv_tt_global_size_mod is called
from two different contexts for the same orig_node_vlan but only one
context is actually removing the entry from the list.
The release function for this orig_node_vlan is not called inside the
vlan_list_lock spinlock protected region because the function
batadv_tt_global_size_mod still holds a orig_node_vlan reference for the
object pointer on the stack. Thus the actual release function (when
required) will be called only at the end of the function.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batadv_gw_node reference counter in batadv_gw_node_update can only be
reduced when the list entry was actually removed. Otherwise the reference
counter may reach zero when batadv_gw_node_update is called from two
different contexts for the same gw_node but only one context is actually
removing the entry from the list.
The release function for this gw_node is not called inside the list_lock
spinlock protected region because the function batadv_gw_node_update still
holds a gw_node reference for the object pointer on the stack. Thus the
actual release function (when required) will be called only at the end of
the function.
Fixes: bd3524c14b ("batman-adv: remove obsolete deleted attribute for gateway node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batadv_tvlv_container* functions state in their kernel-doc that they
require tvlv.container_list_lock. Add an assert to automatically detect
when this might have been ignored by the caller.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
To allow future use of the window protected function with different
maximum sequence numbers, add a parameter to set this value which
was previously hardcoded. Another parameter added for future use is a
flag to return whether the protection window has started.
While at it, also fix the kerneldoc.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The references to the network device should be dropped inside the release
function for batadv_hard_iface similar to what is done with the batman-adv
internal datastructures.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
