There's currently a bug on em28xx-i2c that makes it write the
wrong values to register 06, that controlls the I2C bus speed
and bus.
Fix it to change only the I2C bus flag.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It used to be a code that returns arror at ov7660_init.
However, this was removed by changeset c84e412f:
@@ -231,33 +116,40 @@ int ov7660_init(struct sd *sd)
if (dump_sensor)
ov7660_dump_registers(sd);
- err = ov7660_set_gain(&sd->gspca_dev, sensor_settings[GAIN_IDX]);
- if (err < 0)
- return err;
+ return 0;
+}
- err = ov7660_set_auto_white_balance(&sd->gspca_dev,
- sensor_settings[AUTO_WHITE_BALANCE_IDX]);
- if (err < 0)
- return err;
As complained by gcc:
drivers/media/usb/gspca/m5602/m5602_ov7660.c: In function 'ov7660_init':
drivers/media/usb/gspca/m5602/m5602_ov7660.c:99:9: warning: variable 'err' set but not used [-Wunused-but-set-variable]
It should be noticed that the original error code was crappy, as it wasn't
returning any error if sensor init fails.
Fix it by returning an error if the sensor can't be initialized.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason there seems to be value 0x03 in eeprom for dual mode
(and 0x00 for single mode). Boolean is not always 1 bit wide - it
could be 8 bit wide too. Storing number 0x03 to boolean causes driver
to thing there is 4 tuners in some cases :o
Add also some comments regarding to eeprom.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no difference towards AF9035 remote controller, so enable it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
eeprom memory mapped base address is detected at the very first.
Use it everywhere.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AF9035 and IT9135 supports two different firmware format. Select
correct loader according to first byte of firmware file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't need it. Tuner ID and device address are enough.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now it supports IT9135 based dual tuner devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That same USB ID is used both AF9015 and AF9035 driver.
iManufacturer is only thing we can select correct driver without a I/O.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That same USB ID is used both AF9015 and AF9035 driver.
iManufacturer is only thing we can select correct driver without a I/O.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ADC needs to be also multiplied to 2 as it9135.
Fixes bug I introduced few commits ago.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detect automatically multiple chip versions and select configuration
according to that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the remaining CamelCase checkpatch.pl compliants.
There are still a few left, but those are due to USB and
DVB APIs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is almost impossible to see a compliant with checkpatch.pl
on those Siano drivers, as there are simply too much violations
on it. So, now that a big change was done, the better is to
cleanup the checkpatch compliants.
Let's first replace all CammelCase symbols found at smscoreapi.h
using camel_case namespace. That removed 144 checkpatch.pl
compliants on this file. Of course, the other files need to be
fixed accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that detects the types of sms devices is bogus. It returns
[ 4645.187790] smsusb_init_device: line: 372: Unspecified sms device type!
For several devices, including the one I have (SMS_RIO). In a matter
of fact, the right thing to do there is to print an error only if
the device is really unknown (SMS_UNKNOWN_TYPE).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To avoid mixing two different things at the same place, move the
debugfs code into a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, every time a message is sent or received, the endiannes
need to be fixed on big endian machines. This is currently done
on every call to the send API, and on every msg reception logic.
Instead of doing that, move it to the send/receive functions.
That simplifies the logic and avoids the risk of forgetting to
fix it somewhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using hardcoded descriptors, detect them from the
USB descriptors.
This patch is rebased form Doron Cohen's patch:
http://patchwork.linuxtv.org/patch/7883/
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of printing a message for some random messages, print
it for all sent/received ones. That helps a lot to debug
what's going on.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for the GOTVIEW SatelliteHD card which is based on
Montage M88DS3000 and works very well with this driver.
Signed-off-by: Andrey Pavlenko <andrey.a.pavlenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turned out that some devices return less bytes then requested via i2c when
ALL of the following 3 conditions are met:
- i2c bus B is used
- there was no attempt to write to the specified slave address before
- no device present at the specified slave address
With the current code, this triggers an -EIO error and prints a message to the
system log.
Because it can happen very often during device probing, it is better to ignore
this error and bail out silently after the follwing i2c transaction success
check with -ENODEV.
[mchehab@redhat.com: a small CodingStyle fix]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver obtains the timestamps using function v4l2_get_timestamp(),
which produces a montonic timestamp.
Fixes the warnings appearing in the system log since commit 6aa69f99
"[media] vb2: Add support for non monotonic timestamps"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register both buses 0 and 1 via I2C API. For now, bus 0 is used
only by eeprom on all known devices. Later patches will be needed
if this changes in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare to register a separate bus for the second bus.
For now, just add a new field. A latter patch will add the
bits to make it work.
This patch was generated by this script:
perl -e 'while (<>) { if (s/EM2874_I2C_SECONDARY_BUS_SELECT.*\n//) {
printf "\t\t.def_i2c_bus = 1,\n"; $found = 1; print $_ } else { if ($found) { s/^\s+// }; $found = 0; print $_; } }' \
drivers/media/usb/em28xx/em28xx-cards.c >a && mv a drivers/media/usb/em28xx/em28xx-cards.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer em28xx devices have 2 buses. Change the logic to allow
using both buses.
This patch was generated by this small script:
for i in drivers/media/usb/em28xx/*.c; do
sed 's,->i2c_adap,->i2c_adap[dev->def_i2c_bus],g;s,->i2c_client,->i2c_client[dev->def_i2c_bus],'
done
Of course, em28xx.h needed manual edit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit 7543f344e9 ("[media] m920x:
factor out a m920x_write_seq() function") building m920x.o triggers this
GCC warning:
drivers/media/usb/dvb-usb/m920x.c: In function ‘m920x_probe’:
drivers/media/usb/dvb-usb/m920x.c:91:6: warning: ‘ret’ may be used uninitialized in this function [-Wuninitialized]
This warning is caused by m920x_write_seq(), which is apparently inlined
into m920x_probe(). It is clear why GCC thinks 'ret' may be used
uninitialized. But in practice the first seq->address will always be
non-zero when this function is called. That means we can change the
while()-do{} loop into a do{}-while() loop. And that suffices to make
GCC see that 'ret' will not be used uninitialized.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks for the response, I have done as you suggested.
Below is an updated patch for the OTG102 device against http://git.linuxtv.org/hverkuil/media_tree.git/shortlog/refs/heads/cx231xx, kernel version 3.8.
With further testing it appears the extra clauses in cx231xx-cards.c were not necessary (in static in cx231xx_init_dev and static int cx231xx_usb_probe), so those have been also been removed.
Signed-off-by: Matt Gomboc <gomboc0@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I did what I liked to do. Also corrected two long log writings
as checkpatch.pl was complaining about those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement:
dvb_usbv2_generic_rw_locked()
dvb_usbv2_generic_write_locked()
Caller must hold device lock when locked versions are called.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check for (adap == NULL) has to done before accessing adap.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Terratec Cinergy S2 USB HD Rev.2 support.
This commit is a corrected cherry-pick of 03228792 which got reverted in
b7e38636 because it was rebased incorrectly and introduced compilation
errors.
Signed-off-by: Stephan Hilb <stephan@ecshi.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds USB ID for alternative "Terratec Cinergy T Stick".
Tested by a friend: works similarly to 0ccd:0093 version (af9035+tua9001)
Signed-off-by: Fabrizio Gazzato <fabrizio.gazzato@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID for MaxMedia HU394-T USB DVB-T Multi (FM, DAB, DAB+)
dongle (RTL2832U+FC0012)
In Italy, is branded as "DIKOM USB-DVBT HD"
lsusb: ID 1b80:d394 Afatech
Signed-off-by: Fabrizio Gazzato <fabrizio.gazzato@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The planar YUV422P is quite unusual and few if any applications support it.
Instead choose the common YUYV format as the default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All fields after 'type' are already zeroed by the core framework.
Clearing the full struct also clears 'type', which causes a wrong
type value to be returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just set the field value based on the chosen format. It's either INTERLACED
or TOP.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set priv field of struct v4l2_pix_format to 0 and fill in colorspace.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of comparing against STD_NTSC and STD_PAL compare against 60 and
50 Hz formats. That's what you really want.
When the standard is changed, make sure the width and height of the format
are also updated to reflect the current standard.
Also replace the deprecated current_norm by the g_std ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of the V4L2_CID_JPEG_COMPRESSION_QUALITY control is recommended over
the G/S_JPEGCOMP ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead use v4l2_dbg and v4l2_err. Note that the PDEBUG macro is kept to
make this patch-set less invasive, but it is simply a wrapper around
v4l2_dbg now. Most of the other changes are there to make the dev parameter
for the v4l2_xxx macros available everywhere we do logging.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that sonixj.c has been converted to the control framework it is no
longer used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We forgot to remove that when sonixb was converted to the control framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all drivers use monotonic timestamps. This patch adds a way to set the
timestamp type per every queue.
In addition, set proper timestamp type in drivers that I am sure that use
either MONOTONIC or COPY timestamps. Other drivers will correctly report
UNKNOWN timestamp type instead of assuming that all drivers use monotonic
timestamps.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The spec specifies that setting count to 0 in v4l2_requestbuffers
should result in releasing any streaming resources and the stream
ownership. Implement this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes it possible to switch to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The priv field should be set to 0. In this case the driver abused the priv
field for internal housekeeping. Modify the code so priv is no longer used
for that purpose.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add device_caps support to querycap, fill in bus_info correctly and
do not set the version field (let the core handle that).
Also simplify the s_input ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also correct the first_init static: this should be part of the stk_camera struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
file->private_data is needed to store the pointer to struct v4l2_fh.
So use video_drvdata to get hold of the stk_camera struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's a webcam, the STD API is not applicable to webcams.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And add an extensive comment relating the history of the upside-down
handling in this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Arvydas Sidorenko <asido4@gmail.com>
Thanks-to: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on my big-endian ppc-based test machine.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on my big-endian ppc-based test machine.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's not working reliably if port 3 is enabled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The last set width/height must be preserved as per the spec.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 417 support doesn't work. Until someone can dig into this driver to
figure out why it isn't working the 417 support is disabled.
Sometimes you can actually stream a bit, but very soon the whole machine
crashes, so something is seriously wrong.
For the record, this was not introduced by my recent changes to this driver,
it was broken before that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prefix is generated automatically, so no need to provide it again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Share tuner, frequency, debug and input ioctls with cx231xx-video.
These are all shared resources, so no need to implement them again.
[mchehab@redhat.com: Fix merge conflict and a checkpatch issue]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Colorspace, field and priv were not set, and sizeimage was calculated
using the wrong values (dev->ts1.ts_packet_size and dev->ts1.ts_packet_count
can be 0 at module load).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the initial standard of subdevices instead of leaving it undefined.
Also update the width and height when a new standard is chosen and
return -EBUSY when attempting to change the standard while videobuf is
busy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was already a core lock, so why wasn't ioctl already replaced by
unlock_ioctl?
This patch switches to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of this field is deprecated since it will not work when multiple
device nodes reference the same video input (the video and vbi nodes in
this case). The norm field should be a device-global value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed to resolve the v4l2-compliance complaints about the control
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various v4l2-compliance fixes: remove unused sliced VBI functions, zero the
reserved fields of struct v4l2_vbi_format and implement the missing s_fmt_vbi_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the tuner clamp the frequency and store that clamped value.
This fixes a v4l2_compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The priv field of v4l2_pix_format must be zeroed. Also fix a bug in try_fmt
where the current width was used instead of the width passed to try_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The g_tuner call wasn't passed on to the subdevices, g_frequency didn't
check for invalid tuners and a low-level function that was expected to
return 0 or a negative error returned a positive number instead, causing
s_frequency to return bogus errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio selection code is broken. Audio and video indices were
mixed up and s_audio would reject changing the audio input to
something else anyway, so what's the point?
All the audio input code has been removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Radio should not use video or audio inputs.
In addition, fix a bug in radio_g_tuner where s_tuner was called in the tuner
subdev instead of g_tuner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ioctl debugging can now be done through the debug parameter in sysfs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a poor administration of the driver state it wasn't possible to open
a video or vbi device multiple times.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usual set of problems: the frequency isn't clamped to the frequency range,
no tuner index check and the frequency isn't initialized properly on module
load.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This switch to v4l2_fh resolves the last v4l2_compliance issues with respect
to control events and priority handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The input and audio ioctls are only valid for video/vbi nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver already does locking, so it is safe to switch to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver now passes the tuner and frequency tests of v4l2-compliance.
It's the usual bugs: frequency wasn't clamped to the valid frequency range,
incorrect tuner capabilities and tuner fields not filled in, missing test
for invalid tuner index, no initial frequency and incorrect error handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the correct parent for v4l2_device_register and don't set the name
anymore (that's now deduced from the parent). Also remove an unnecessary
forward reference and fix two weird looking log messages.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using 3.3 MHz IF, use 4MHz. That's the standard
value for the demod, and, while it can be adjusted, 3.3 MHz
is out of the recommended range. So, let's stick with the
default.
With regards to the IF voltage level, instead of using
0.5 V(p-p) for IF, use 2V, giving a 12dB gain.
The rationale is that, on PixelView SBTVD Hybrid,
even 2V(p-p) would be in the nominal range for IF,
as the maximum range on this particular device is 3V.
A higher gain here should help to improve reception under
weak signals.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduces the number of characters/lines, unifies the code and improves readability.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner type is set by the v4l2-core based on the device type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -EINVAL inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_G_AUDIO and
VIDIOC_S_AUDIO if the device doesn't support audio.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable the ioctls VIDIOC_G_TUNER, VIDIOC_S_TUNER, VIDIOC_G_FREQUENCY and
VIDIOC_S_FREQUENCY for video and VBI devices without tuner.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_QUERYSTD,
VIDIOC_G_STD and VIDIOC_S_STD if the device is a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
The "Technisat SkyStar USB plus" is a TT-connect S-2400 clone, which the
V4L-DVB drivers already support. However, some of these devices (like
mine) come with a different USB PID 0x3009 instead of 0x3006.
There have already been patches simply overwriting the USB PID in
dvb-usb-ids.h. Of course these patches were rejected because they would
have disabled the 0x3006 PID.
This new patch adds the 0x3009 PID to dvb-usb-ids.h, and adds references
to it within the ttusb2.c driver. PID 0x3006 devices will continue to work.
The only difference between the two hardware models seems to be the
EEPROM chip. In fact, Windows BDA driver names the 0x3009 device with a
"(8 kB EEPROM)" suffix. In spite of that, the 0x3009 device works
absolutely flawlessly using the existing ttusb2 driver.
Signed-off-by: Christoph Nuscheler <christoph.nuscheler@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems to work just the same as older revisions.
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to videobuf2, some unnecessary calls of
em28xx_set_alternate() have been removed. It is now called at analog streaming
start only.
This has unveiled a bug that causes USB bulk transfers to fail with all urbs
having status -EVOERFLOW.
The reason is, that for bulk transfers usb_set_interface() needs to be called
even if the previous alt setting was the same (side note: bulk transfers seem
to work only with alt=0).
While it seems to be NOT necessary for isoc transfers, it's reasonable to just
call usb_set_interface() unconditionally in em28xx_set_alternate().
Also add a comment that explains the issue to prevent regressions in the future.
Cc: stable@vger.kernel.org # for 3.8
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tm6000_poll could use an uninitialized buf pointer. Move the buf-handling
code inside the 'if' that initializes the buf pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is driven by a static checker warning.
The ttusb_process_muxpack() function is only called from
ttusb_process_frame(). Before calling, it verifies that len >= 2. The
problem is that len == 2 is not valid and would lead to an array
underflow.
Odd number values for len are also invalid and would lead to reading
past the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bytesperline calculation was incorrect: it used the old width instead of
the provided width. Fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ttusb2 module is already updated to recognize the TechnoTrend CT-3650
CI DVB C/T USB2.0 receiver in addition to the Pinnacle 400e. But if
MEDIA_SUBDRV_AUTOSELECT is used, the required tuner and demodulator
modules are not automatically selected. Here's a patch to fix that and add a
note of the CT-3650 to the online help of the ttusb2 module.
This patch applies cleanly to 3.7.6 and other 3.7.x kernels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allocation had no error checking. It didn't need to be under
the mutex so I moved it out form there. That makes the error handling
easier and is a potential speed up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the bit shifting of width+height values inside the function
- fix the debug message format and output values
- add comment about the size limit (e.g. EM277x supports >2MPix)
- make void, because error checking is incomplete and we never check the
returned value (we would continue anyway)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those optional operations are used to release and reacquire the queue
lock when videobuf2 needs to perform operations that sleep for a long
time, such as waiting for a buffer to be complete. Implement them to
avoid blocking qbuf or streamoff calls when a dqbuf is in progress.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for Digivox Mini HD (rtl2832)
The tuner works, but with worst performance then realtek linux driver,
due to incomplete implementation of fc2580.c
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Tested-by: Lorenzo Dongarrà <lorenzo_64@katamail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove em28xx_i2c_ir_work() and check the device type in the common callback
function em28xx_ir_work() instead. Simplifies em28xx_ir_start().
Reduces the code size with a minor performance drawback.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set up the i2c_client locally in em28xx_i2c_ir_handle_key().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already have the key polling functions and the polling infrastructure in
em28xx-input, so we can easily get rid of the dependency on module ir-kbd-i2c.
For maximum safety, do not touch the key reporting mechanism for those devices.
Code size could be improved further but would have minor peformance impacts.
Tested with device "Terratec Cinergy 200 USB" (EM2800_BOARD_TERRATEC_CINERGY_200)
[mchehab@redhat.com: Fix two checkpatch.pl warnings:
ERROR: "foo * bar" should be "foo *bar" (line 465)
WARNING: kfree(NULL) is safe this check is probably not required (line 725)]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't report any key/scan codes or errors inside the key polling functions
for internal IR RC devices, just in the key handling fucntions.
Do the same for external devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Field 'old' of struct IR_i2c is used nowhere in module ir-kbd-i2c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My static checker complains about the fall through here. From the
context it looks like we should add a break statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced in 7757ddda6f, where
instead of bit-negating the bitmask, the bit position was bit-negated
instead.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two fixes:
- the priv field wasn't set to 0.
- only V4L2_FIELD_INTERLACED is supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add device_caps support
- fix bus_info
- fix numerous tuner-related problems due to incorrect tests
and setting v4l2_tuner fields to wrong values.
- remove (audio) input support from the radio: it doesn't belong
there. This also fixed a nasty issue where opening the radio
would set dev->input to 5 for no good reason. This was never
set back to a valid TV input after closing the radio device,
thus leaving it at 5 which is out of bounds of the vinput
card array.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead chaneg the passed in format to the pwc default pixelformat.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mike Isely <isely@pobox.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-By: Mike Isely <isely@pobox.com>
The uvc_set_ctrl() calls don't write to the hardware. A failure at that
point thus leaves the device in a clean state, with no control modified.
Set the error_idx field to the count value to reflect that, as per the
V4L2 specification.
TRY_EXT_CTRLS is unchanged and the error_idx field must always be set to
the failed control index in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit ba68c8530a263dc4de440fa10bb20a1c5b9d4ff5 (Partly revert "[media]
uvcvideo: Set error_idx properly for extended controls API failures")
also reverted part of commit 30ecb936cb
("uvcvideo: Return -EACCES when trying to access a read/write-only
control") by mistake. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remy Blank reported that audio over USB can be made working for the television
input if .amux is changed from EM28XX_AMUX_LINE_IN to EM28XX_AMUX_VIDEO.
An examination of his devices shows, that it is indeed supplied with an EM202
AC97 audio IC. We also use this setting for the Cinergy 200.
Remy Blank also provided the original version of this patch (many thanks !).
Fixes bug 14126 (see bug report for further device details).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mutex_lock_interruptible is used on paths where a signal can be
pending, the device is not closed properly and cannot be reused.
This usually happens when you start tzap for example and send it a
TERM signal. The signal is pending while tear-down routines are
called. Hence streaming is not properly stopped in that case. And
the device stops working from that moment on.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Device with ID 1b80:d393 is the Gigabyte U7300 DVB-T dongle.
It contains decoder Realtek RTL2832U and tuner Fitipower FC0012.
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alexander Inyukhin <shurick@sectorb.msk.ru>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use own flag to mark when rc polling is active/deactive and make
decisions, like start/stop polling on suspend/resume, against that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better (cheaper) to use dummy defines for functions
that has no meaning when remote controller is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are not needed anymore as all dvb-usb-v2 drivers has proper
dependency checks for RC-core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it possible to compile dvb_usb_v2 driver without the remote
controller (RC-core).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to copy config to the driver state. Those are coming from
the const struct and could be used directly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That adds support for AF9035 dual devices having FC0012 tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need even more configuration options and overloading dvb_attach()
for all those sounds quite stupid. Due to that switch struct and make
room for new options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various small changes and fixes releated to dual mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that it uses videobuf2, em28xx can support DMABUF.
Tested with an HVR-950 on analog mode and a 2gen i5core machine
with an i915 graphics adapter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That fixes the following warning:
drivers/media/usb/em28xx/em28xx-video.c:611:5: warning: no previous prototype for 'em28xx_stop_streaming' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
EEPROMs are currently read in blocks of 16 bytes, but the em2800 is limited
to 4 bytes per read. All other chip variants support reading of max. 64 bytes
at once (according to the em258x datasheet; also verified with em2710, em2882,
and em28174).
Since em2800_i2c_recv_bytes() has been fixed to return with -EOPNOTSUPP when
more than 4 bytes are requested, EEPROM reading with this chip is broken.
It was actually broken before that change, too, it just didn't throw an error
because the i2c adapter silently returned trash data (for all reads >1 byte !).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- do not pass USB specific error codes to userspace/i2c-subsystem
- unify the returned error codes and make them compliant with
the i2c subsystem spec
- check number of actually transferred bytes (via USB) everywehere
- fix/improve debug messages
- improve code comments
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_FUNC_SMBUS_EMUL includes flag I2C_FUNC_SMBUS_WRITE_BLOCK_DATA which signals
that up to 31 data bytes can be written to the ic2 client.
But the EM2800 supports only i2c messages with max. 4 data bytes.
I2C_FUNC_IC2 should be set if a master_xfer function pointer is provided in
struct i2c_algorithm.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
