While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).
Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.
Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again
Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent update to smatch is causing it to report the error "we previously
assumed 'm_entry->vsi_list_info' could be null". Fix that.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In code comments, use Tx|Rx instead of tx|rx
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function signatures that do not exceed 80-characters should be on a single
line.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up number of formatting issues and a comment that could use
clarification.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_napi_poll is hard-coded to return zero when it's done. It should
instead return the work done (if any work was done). The only time it
should return zero is if an interrupt or poll is handled and no work
is performed. So change the return value to be the minimum of work
done or budget-1.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Indicate these structs should not be modified and take advantage of some
compiler optimizations by making these structs const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the action fields for a MAC-VLAN filter, do not set the LAN_EN flag
if the MAC in the MAC-VLAN is unicast MAC. The unicast packets that
match should not be forwarded to the wire.
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added check of return value for ice_init_def_sw_recp().
Now we know if memory was correctly allocated.
Signed-off-by: Jaroslaw Ilgiewicz <jaroslaw.ilgiewicz@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Assigning the register offset and mask values contains duplicate code
that can easily be replaced with a macro.
2. Separate functions for freeing send queue and receive queue rings are
not needed; replace with a single function that uses a pointer to the
struct ice_ctl_q_ring structure as a parameter instead of a pointer to
the struct ice_ctl_q_info structure.
3. Initializing register settings for both send queue and receive queue
contains duplicate code that can easily be replaced with a helper
function.
4. Separate functions for freeing send queue and receive queue buffers are
not needed; duplicate code can easily be replaced with a macro.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If VSI state is up, we should do autoneg with link up, otherwise
with link down.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the condition checking of VSI TX queue number to
ICE_MAX_TXQ_PER_TXQG. This is an unnecessary check and causes a driver
load error on hosts that have more than 128 cores.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The scheduler tree is is always rebuilt during reset. The existing code
adds new scheduler nodes for queues but may not clean up earlier nodes.
This patch removed the old scheduler tree during reset before it is
rebuilt.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch includes below changes to resolve the issue of ETS bandwidth
shaping to work.
1. Allocation of Tx queues is accounted for based on the enabled TC's
in ice_vsi_setup_q_map() and enabled the Tx queues on those TC's via
ice_vsi_cfg_txqs()
2. Get the mapped netdev TC # for the user priority and set the priority
to TC mapping for the VSI.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous to this commit the driver was immediately stopping Tx/Rx
queues when doing the following "echo 0 > sriov_numvfs" and then it was
calling pci_disable_sriov if the VFs are not assigned. This was causing
the VIRTCHNL_OP_DISABLE_QUEUES to fail because it was trying to stop
the queues for a second time.
Fix this by calling pci_disable_sriov before stopping the Tx/Rx queues.
This allows the VIRTCHNL_OP_DISABLE_QUEUES to get processed before the
driver tries to stop the Rx/Tx queues in ice_free_vfs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With much traffic coming into the port, Rx queue disable
procedure can take more time until all pending queue
requests on PCIe finish. Reuse ICE_Q_WAIT_MAX_RETRY macro
and increase the delay itself.
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes bad masks that would break compilation when evaluated.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dis_vsi() performs an rtnl_lock() if it detects a netdev that is
running on the VSI. In cases where the RTNL lock has already been
acquired, a deadlock results. Add a boolean to pass to ice_dis_vsi to
tell it if the RTNL lock is already held.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are setting the guar_num_vsi to equal to ICE_MAX_VSI
which is the device limit of 768. This is incorrect and could have
unintended consequences. To fix this use the valid_function's 8-bit
bitmap returned from discovering device capabilities to determine the
guar_num_vsi per function. guar_num_vsi value is then passed on to
pf->num_alloc_vsi.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before releasing the VSI, remove the VSI scheduler node. If not,
the node is left in the scheduler tree and, on subsequent load, the
scheduler tree contains the node so it does not set it in vsi_ctx.
This, later, causes the node to not be found in ice_sched_get_free_qparent
which leads to a "Failed to set LAN Tx queue context, error: -1".
To remove the scheduler node, this patch introduces ice_rm_vsi_lan_cfg
and related helpers.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a gap in time between a VF reset, which sets the q_vector to
NULL, and the VF requesting mapping of the q_vectors. If
ice_vsi_stop_tx_rings() is called during this time, a NULL pointer
dereference is encountered. Add a check in ice_vsi_stop_tx_rings()
to ensure the q_vector is set to avoid this situation from occurring.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the debug print in ice_tx_timeout is printing useless and
duplicate values. First, head is being assigned to tx_ring->next_to_clean
and we are printing both of those values, but naming them HWB and NTC
respectively. Also, reading tail always returns 0 so remove that as well.
Instead of assigning the SW head (NTC) read to head, use the actual head
register and change the debug print to note that this is HW_HEAD. Also
reduce the scope of a couple variables.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.
Fix this by changing req_speeds to be u16.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.
Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.
Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);
An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.
In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.
In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.
The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.
This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.
This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:
ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1
The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.
Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print should say "Enabling" instead of "Enaabling"
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the spec, whenever insert PVID field is set, the VLAN
driver insertion mode should be set to 01b which isn't done currently.
Fix it.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The remove path does not currently check to see if a
reset is in progress before proceeding. This can cause
a resource collision resulting in various types of errors.
Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.
For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate VF interrupts using VPINT_ALLOC_PCI. Multiple interrupts are
specified as a range from "first" to "last".
Also, according to the spec, the queue mapping for a VF needs to be set
in both contig and scatter queue modes. So make this change as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains a couple of driver workarounds for current
firmware limitations. These workarounds are expected to go away once
these limitations are fixed in the firmware.
On a firmware release that has these issues addressed, these workarounds
(while unnecessary) will not break anything.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware now returns the capability count in the command buffer.
Use it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update to the current firmware major and minor version which are
1 and 3 respectively.
Also remove an empty comment line.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Basically remove references to C810 and use E810C (from the branding
string) instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 158a08a694 ("ice: remove ndo_poll_controller") removed
ice_netpoll and introduced a namespace warning for ice_msix_clean_rings.
Fix the namespace warning by making ice_msix_clean_rings static.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update version string to 0.7.2-k
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_ena/dis_vsi should have a single differentiating
factor to determine if the netdev_ops call is used or a
direct call to ice_vsi_open/close. This is if the netif is
running or not. If netif is running, use ndo_open/ndo_close.
Else, use ice_vsi_open/ice_vsi_close.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This issue came about when looking at the VF function
ice_vc_cfg_irq_map_msg. Currently we are assigning the itr_setting value
to the itr_idx received from the AVF driver, which is not correct and is
not used for the VF flow anyway. Currently the only way we set the ITR
index for both the PF and VF driver is by hard coding ICE_TX_ITR or
ICE_RX_ITR for the ITR index on each q_vector.
To fix this, add the member itr_idx in struct ice_ring_container. This
can then be used to dynamically program the correct ITR index. This change
also affected the PF driver so make the necessary changes there as well.
Also, removed the itr_setting member in struct ice_ring because it is not
being used meaningfully and is going to be removed in a future patch that
includes dynamic ITR.
On another note, this will be useful moving forward if we decide to split
Rx/Tx rings on different q_vectors instead of sharing them as queue pairs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks in the filter handling flow to avoid dereferencing
NULL pointers.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a switch rule is initially created we set the filter action to
ICE_FWD_TO_VSI. The filter action changes to ICE_FWD_TO_VSI_LIST
whenever more than one VSI is subscribed to the same switch rule. When
the switch rule goes from 2 VSIs in the list to 1 VSI we remove and
delete the VSI list rule, but we currently don't update the switch rule
in hardware. This is causing switch rules to be lost, so fix that by
making a call to ice_update_pkt_fwd_rule() with the necessary changes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding a rule, queue region size needs to be provided as log base 2
of the number of queues in region. Fix that.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the existing malicious driver operation detection
logic to cover malicious operations by the VF driver as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PF gets a link status change event, notify the VFs of the same.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
virtchnl is a protocol/interface specification that allows the Intel
"Adaptive Virtual Function (AVF)" driver (iavf.ko) to work with more than
one physical function driver. The AVF driver sends "virtchnl commands"
(control plane only) to the PF driver over mailbox queues and the PF driver
executes these commands and returns a result to the VF, again over mailbox.
This patch adds AVF support for the ice PF driver by implementing the
following virtchnl commands:
VIRTCHNL_OP_VERSION
VIRTCHNL_OP_GET_VF_RESOURCES
VIRTCHNL_OP_RESET_VF
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_REQUEST_QUEUES
VIRTCHNL_OP_CONFIG_IRQ_MAP
VIRTCHNL_OP_CONFIG_RSS_KEY
VIRTCHNL_OP_CONFIG_RSS_LUT
VIRTCHNL_OP_GET_STATS
VIRTCHNL_OP_ADD_VLAN
VIRTCHNL_OP_DEL_VLAN
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
