When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add device remove and module exit code to make the driver
functioning as a loadable module.
Fixes: ac28927659 (cpufreq: kryo: allow building as a loadable module)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In event of error returned by the nvmem_cell_read() non-pointer value
may be dereferenced. Fix this with error handling.
Additionally free the allocated speedbin buffer, as per the API.
Fixes: 9ce36edd1a52 (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 80c49563e2 ("scsi: scsi_debug: implement IMMED bit") there
are long delays in F_SYNC_DELAY and F_SSU_DELAY. This can cause a memory
leak in schedule_resp(), which can be invoked while unloading the
scsi_debug module: free_all_queued() had already freed all sd_dp and
schedule_resp will alloc a new one, which will never get freed. Here's the
kmemleak report while running xfstests generic/350:
unreferenced object 0xffff88007d752b00 (size 128):
comm "rmmod", pid 26940, jiffies 4295816945 (age 7.588s)
hex dump (first 32 bytes):
00 2b 75 7d 00 88 ff ff 00 00 00 00 00 00 00 00 .+u}............
00 00 00 00 00 00 00 00 8e 31 a2 34 5f 03 00 00 .........1.4_...
backtrace:
[<000000002abd83d0>] 0xffffffffa000705e
[<000000004c063fda>] scsi_dispatch_cmd+0xc7/0x1a0
[<000000000c119a00>] scsi_request_fn+0x251/0x550
[<000000009de0c736>] __blk_run_queue+0x3f/0x60
[<000000001c4453c8>] blk_execute_rq_nowait+0x98/0xd0
[<00000000d17ec79f>] blk_execute_rq+0x3a/0x50
[<00000000a7654b6e>] scsi_execute+0x113/0x250
[<00000000fd78f7cd>] sd_sync_cache+0x95/0x160
[<0000000024dacb14>] sd_shutdown+0x9b/0xd0
[<00000000e9101710>] sd_remove+0x5f/0xb0
[<00000000c43f0d63>] device_release_driver_internal+0x13c/0x1f0
[<00000000e8ad57b6>] bus_remove_device+0xe9/0x160
[<00000000713a7b8a>] device_del+0x120/0x320
[<00000000e5db670c>] __scsi_remove_device+0x115/0x150
[<00000000eccbef30>] scsi_forget_host+0x20/0x60
[<00000000cd5a0738>] scsi_remove_host+0x6d/0x120
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch reverts changes done in qlt_schedule_sess_for_deletion() to
avoid spinlock recursion sess->vha->work_lock should be used instead
of ha->tgt.sess_lock, that can be locked in callers: qlt_reset() or
qlt_handle_login()
[mkp: roll in build warning reported by sfr]
Fixes: 1c6cacf4ea ("scsi: qla2xxx: Fixup locking for session deletion")
Cc: <stable@vger.kernel.org> #v4.17
Signed-off-by: Mikhail Malygin <m.malygin@yadro.com>
Reported-by: Mikhail Malygin <m.malygin@yadro.com>
Tested-by: Mikhail Malygin <m.malygin@yadro.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver does both wmb() and writel(). The latter already has a barrier
on some architectures like arm64. This ends up with CPU observing two
barriers back to back before executing the register write.
Drivers should generally assume that the barrier implied by writel() is
sufficient for ordering DMA. Remove the extraneous wmb() before it.
[mkp: Squashed Arnd's and Sinan's patches]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Generally target core and TCMUser seem to work fine for tape devices and
media changers. But there is at least one situation where TCMUser is not
able to support sequential access device emulation correctly.
The situation is when an initiator sends a SCSI READ CDB with a length that
is greater than the length of the tape block to read. We can distinguish
two subcases:
A) The initiator sent the READ CDB with the SILI bit being set.
In this case the sequential access device has to transfer the data from
the tape block (only the length of the tape block) and transmit a good
status. The current interface between TCMUser and the userspace does
not support reduction of the read data size by the userspace program.
The patch below fixes this subcase by allowing the userspace program to
specify a reduced data size in read direction.
B) The initiator sent the READ CDB with the SILI bit not being set.
In this case the sequential access device has to transfer the data from
the tape block as in A), but additionally has to transmit CHECK
CONDITION with the ILI bit set and NO SENSE in the sensebytes. The
information field in the sensebytes must contain the residual count.
With the below patch a user space program can specify the real read data
length and appropriate sensebytes. TCMUser then uses the se_cmd flag
SCF_TREAT_READ_AS_NORMAL, to force target core to transmit the real data
size and the sensebytes. Note: the flag SCF_TREAT_READ_AS_NORMAL is
introduced by Lee Duncan's patch "[PATCH v4] target: transport should
handle st FM/EOM/ILI reads" from Tue, 15 May 2018 18:25:24 -0700.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ctxdmas for cursors from all heads are setup in the core channel, and due
to us tracking allocated handles per-window, we were failing with -EEXIST
on multiple-head setups trying to allocate duplicate handles.
The cursor code is hardcoded to use the core channel vram ctxdma already,
so just skip ctxdma allocation for cursor fbs to fix the issue.
Fixes: 5bca1621c0 ("drm/nouveau/kms/nv50-: move fb ctxdma tracking into windows")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull jfs fix from Dave Kleikamp:
"This fixes a too-small allocation in the xattr code"
* tag 'jfs-4.18' of git://github.com/kleikamp/linux-shaggy:
jfs: Fix inconsistency between memory allocation and ea_buf->max_size
Pull s390 updates from Martin Schwidefsky:
"common I/O layer
- Fix bit-fields crossing storage-unit boundaries in css_general_char
dasd driver
- Avoid a sparse warning in regard to the queue lock
- Allocate the struct dasd_ccw_req as per request data. Only for
internal I/O is the structure allocated separately
- Remove the unused function dasd_kmalloc_set_cda
- Save a few bytes in struct dasd_ccw_req by reordering fields
- Convert remaining users of dasd_kmalloc_request to
dasd_smalloc_request and remove the now unused function
vfio/ccw
- Refactor and improve pfn_array_alloc_pin/pfn_array_pin
- Add a new tracepoint for failed vfio/ccw requests
- Add a CCW translation improvement to accept more requests as valid
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: only use preallocated requests
s390/dasd: reshuffle struct dasd_ccw_req
s390/dasd: remove dasd_kmalloc_set_cda
s390/dasd: move dasd_ccw_req to per request data
s390/dasd: simplify locking in process_final_queue
s390/cio: sanitize css_general_characteristics definition
vfio: ccw: add tracepoints for interesting error paths
vfio: ccw: set ccw->cda to NULL defensively
vfio: ccw: refactor and improve pfn_array_alloc_pin()
vfio: ccw: shorten kernel doc description for pfn_array_pin()
vfio: ccw: push down unsupported IDA check
vfio: ccw: fix error return in vfio_ccw_sch_event
s390/archrandom: Rework arch random implementation.
s390/net: add pnetid support
The patch fixed a W=1 warning but broke the ia64 build:
CC mm/memblock.o
mm/memblock.c:1340: error: redefinition of `memblock_virt_alloc_try_nid_raw'
./include/linux/bootmem.h:335: error: previous definition of `memblock_virt_alloc_try_nid_raw' was here
Because inlcude/linux/bootmem.h says
#if defined(CONFIG_HAVE_MEMBLOCK) && defined(CONFIG_NO_BOOTMEM)
whereas mm/Makefile says
obj-$(CONFIG_HAVE_MEMBLOCK) += memblock.o
So revert 26f09e9b3a ("mm/memblock: add missing include
<linux/bootmem.h>") while a full fix can be worked on.
Fixes: 26f09e9b3a ("mm/memblock: add missing include <linux/bootmem.h>")
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19461/
Signed-off-by: James Hogan <jhogan@kernel.org>
Run the completer task to post a work completion after processing
a memory registration or invalidate work request. This covers the
case where the memory registration or invalidate was the last work
request posted to the qp.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On some Mali-DP processors, the LAYER_FORMAT register contains fields
other than the format. These bits were unconditionally cleared when
setting the pixel format, whereas they should be preserved at their
reset values.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Ayan Kumar halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
This patch fixes the below parser error of the IOB SLOW PMU.
# perf stat -a -e iob-slow0/cycle-count/ sleep 1
evenf syntax error: 'iob-slow0/cycle-count/'
\___ parser error
It replaces the "-" character by "_" character inside the PMU name.
Signed-off-by: Hoan Tran <hoan.tran@amperecomputing.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a9 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the MAINTAINERS file to cover the "stingray" pattern and a few
files under arch/arm64/boot/dts/broadcom/* as well as the clock driver
and binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While moving the Northstar 2 DTS into a dedicated directory, the
corresponding MAINTAINERS file entry was not updated accordingly, fix
that.
Fixes: 63a913c157 ("arm64: dts: move ns2 into northstar2 directory")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Delete RUN_TESTS and EMIT_TESTS overrides and use common defines in
lib.mk. Common defines work just fine and there is no need to define
custom overrides.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Tom Hromatka <tom.hromatka@oracle.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
sparc64 test fails with the following errors on non-sparc64 systems. Fix
the Makefile to do nothing on non-sparc64 systems to suppress the errors:
make run_tests
adi-test.c: Assembler messages:
adi-test.c:302: Error: no such instruction: `rd %tick,%r13'
adi-test.c:304: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:190: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:192: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:273: Error: no such instruction: `rd %tick,%rbx'
adi-test.c:276: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:217: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:220: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:246: Error: no such instruction: `rd %tick,%rbp'
adi-test.c:248: Error: no such instruction: `rd %tick,%rdx'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
adi-test.c:79: Error: no such instruction: `rd %tick,%rax'
<builtin>: recipe for target 'adi-test' failed
make[1]: *** [adi-test] Error 1
adi: [FAIL]
./drivers_test.sh: 24: ./drivers_test.sh: ./adi-test: not found
../lib.mk:73: recipe for target 'run_tests' failed
make: *** [run_tests] Error 1
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Tom Hromatka <tom.hromatka@oracle.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Unless the software synchronization objects (CONFIG_SW_SYNC) is enabled,
the sync test will be skipped:
TAP version 13
1..0 # Skipped: Sync framework not supported by kernel
Add a config fragment file to be able to run "make kselftest-merge" to
enable relevant configuration required in order to run the sync test.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Link: https://lkml.org/lkml/2017/5/5/14
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When vm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the
test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When zram test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When user test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run. Add an explicit check
for module presence and return skip code if module isn't present.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When sysctl test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Changed return code to kselftest skip code in skip error legs that check
requirements and module probe test error leg.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When static_keys test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as a fail
by the Kselftest framework. This leads to false negative result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit searches for test_static_key_base and test_static_keys
modules and return skip code if they aren't found to differentiate between
the failure to load the module condition and module not found condition.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
When pstore_post_reboot test gets skipped because of unmet dependencies
and/or unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
On this system EC interrupt triggers constantly kicking devices out of
low power states and thus blocking power management. The system also has
a PCIe root port hosting Alpine Ridge Thunderbolt controller and it
never gets a chance to go to D3cold because of this.
Since the power button works the same regardless if EC interrupt is
enabled or not during s2idle, add a quirk for this machine that sets
ec_no_wakeup=true preventing spurious wakeups.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
adds support for handling clocks and resets in the DWC3 core, so that for
platforms following the standard devicetree bindings this does not need
to be duplicated in all the different glue layers.
These changes intended for devicetree based platforms introduce an
uncoditional clk_bulk_get() in the core probe path. This leads to the
following error being logged on x86/ACPI systems:
[ 26.276783] dwc3 dwc3.3.auto: Failed to get clk 'ref': -2
This commits wraps the clk_bulk_get() in an if (dev->of_node) check so
that it only is done on devicetree instantiated devices, fixing this
error.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
