Multi-pipe LP1+ watermarks are a HSW+ feature, so let's not do it on
earlier generations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK disabling LP1+ watermarks must be done carefully to avoid
underruns. If we just write 0 to the register in the middle of the scan
cycle we often get an underrun. So instead we have to leave the actual
watermark levels in the register intact, and just toggle the enable bit.
Presumably the hardware takes a while to get out of low power mode, and
so the watermark level need to stay valid until that time.
We also have to be careful with the WM1S_LP_EN bit. It seems the
hardware more or less treats it like the actual watermarks numbers, and
so we must not toggle it too soon. Just leave it alone when disabling
the LP1+ watermarks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK/SNB don't have LP2+ watermarks for sprites. Also the LP1 sprite
watermark register has its own enable bit. Take these differences
into account when programming the LP1+ registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK/SNB only LP0/1 watermarks can be enabled when sprites are
enabled, and on ILK/SNB/IVB sprite scaling is limited to LP0 only.
So we can avoid computing the extra levels we're never going to use.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new function ilk_wm_lp_latency() which will tell us what to write
into the WM_LPx register latency field. HSW is different from erlier
gens in this regard.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB the display data buffer partitioning control lives in the
DISP_ARB_CTL2 register. Add the relevant defines/code for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaVSRefCountFullforceMissDisable and
WaDSRefCountFullforceMissDisable
VS is a carry-over from HSW, and DS is likely not used by anyone yet.
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Line of 106 chars is too long. Really.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I stumbled on to some unimplemented errata. To be honest, I am not
really sure of the impact, just that the docs say to do.
No w/a name for this one.
v2: v1 was a stale thing which should have never seen the light of day.
(Haihao)
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't touch DPFC_RECOMP_CTL on FBC2, use RMW to update
the FBC_CONTROL on FBC1 to make it easier for people to
experiment with different numbers. Also fix the interval
mask for FBC1.
v2: Rebased
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 and gen3 don't have the FBC_CONTROL2 register, so don't
touch it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the compressed frame buffer pitch is specified in 32B units
rather than the 64B units used on gen3+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes regression introduced by:
commit bf51d5e2cd
Author: Paulo Zanoni <paulo.r.zanoni at intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
The bug I'm seeing can be reproduced with:
- Have vgacon configured/enabled
- Make sure the power well gets disabled, then enabled. You can
check this by seeing the messages print by hsw_set_power_well
- Stop your display manager
- echo 0 > /sys/class/vtconsole/vtcon1/bind
I can easily reproduce this by blacklising snd_hda_intel and booting
with eDP+HDMI.
If you do this and then look at dmesg, you'll see we're printing
infinite "Unclaimed register" messages. This is happening because
we're stuck on an infinite loop inside console_unlock(), which is
calling many functions from vgacon.c. And the code that's triggering
the error messages is from vgacon_set_cursor_size().
After we re-enable the power well, every time we read/write the VGA
address 0x3d5 we get an "unclaimed register" interrupt (ERR_INT) and
print error messages. If we write anything to the VGA MSR register (it
doesn't really matter which value you write to bit 0), any
reads/writes to 0x3d5 _don't_ trigger the "unclaimed register" errors
anymore (even if MSR bit 0 is zero). So what happens with the current
code is that when we unbind i915 and bind vgacon, we call
console_unlock(). Function console_unlock() is responsible for
printing any messages that were supposed to be print when the console
was locked, so it calls the TTY layer, which calls the console layer,
which calls vgacon to print the messages. At this point, vgacon
eventually calls vgacon_set_cursor_size(), which touches 0x3d5, which
triggers unclaimed register interrupts. The problem is that when we
get these interrupts, we print the error messages, so we add more work
to console_unlock(), which will try to print it again, and then call
vgacon again, trigger a new interrupt, which will put more stuff to
the buffer, and then we'll be stuck at console_unlock() forever.
If you patch intel_uncore.c to not print anything when we detect
unclaimed registers, we won't get into the console_unlock() infinite
loop and the driver unbind will work just fine. We will still be
getting interrupts every time vgacon touches those registers, but we
will survive. This is a valid experiment, but IMHO it's not the real
fix: if we don't print any error messages we will still keep getting
the interrupts, and if we disable ERR_INT we won't get the interrupt
anymore, but we will also stop getting all the other error interrupts.
I talked about this problem with the HW engineer and his
recommendation is "So don't do any VGA I/O or memory access while the
power well is disabled, and make to re-program MSR after enabling the
power well and before using VGA I/O or memory accesses.".
Notice that this is just a partial fix to fd.o #67813. This fixes the
case where the power well is already enabled when we unbind, not when
it's disabled when we unbind.
V2: - Rebase (first version was sent in September).
V3: - Complete rewrite of the same fix: smaller implementation,
improved commit message.
Testcase: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67813
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to add more code to the post_enable function.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.
This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.
v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initialize the FBC vfuncs on gen2 and gen3 chipsets. Also make
a clean split for gen7+ vs. gen5+ vfunc initialization.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 and gen3 chipsets FBC is supported only on plane A. Fix (and
simplify) the plane checks in intel_update_fbc() accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call intel_display_power_enabled() from
i915_capture_error_state() in IRQ context and then take a mutex. To fix
this add a new intel_display_power_enabled_sw() which returns the domain
state based on software tracking as opposed to reading the actual HW
state.
Since we use domain_use_count for this without locking on the reader
side make sure we increase the counter only after enabling all required
power wells and decrease it before disabling any of these power wells.
Regression introduced in
commit 1b02383464b4a915627ef3b8fd0ad7f07168c54c
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Sep 24 16:17:09 2013 +0300
drm/i915: support for multiple power wells
Note that atm we depend on the value returned by
intel_display_power_enabled_sw() in i915_capture_error_state() to avoid
unclaimed register access reports. This was never guaranteed though,
since another thread can disable the power concurrently. If this is a
problem we need another explicit way to disable the reporting during
error captures.
v2:
- remove barriers as the caller can't depend on the value
returned from i915_capture_error_state_sw() anyway (Ville)
- dump the state of pipe/transcoder power domain state (Daniel)
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setting this bit restores all ring contexts in parallel rather than
serially. Matches current BWG recommendations.
Tested-by: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Deepak S <deepak.s@inel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use timeout mode, and we need to lower the timeout to get good RC6
residency when loads are running. This gets me from 0% residency during
glxgears to 77%, which is a pretty good improvement. This value also
matches the current BWG recommentations.
Tested-by: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Deepak S <deepak.s@inel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split vlv force wake routines to help individually control Media/Render
well based on the register access.
We've seen power savings in the lower sub-1W range on workloads that
only need on of the power wells, e.g. glbenchmark, media playback
Note: The same split isn't there for the forcewake queue, only the
forcwake domains are split.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rebase on top of the removed forcewake hack in the ring irq
get/put code and add a note to add Deepak's answer to Chris question.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added power well arguments to all the force wake routines
to help us individually control power well based on the
scenario.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the removed forcewake hack and drop one
spurious hunk Jesse noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a debugfs entry showing the use-count for all power domains of each
power well.
v3: address comments from Paulo:
- simplify power_domain_str() by using a switch table
- move power_well::domain_count to power_domains
- WARN_ON decrementing a 0 refcount
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we distinguished platforms without a dynamic power well with
the HAS_POWER_WELL macro and for such platforms we didn't call any power
domain functions. Instead of doing this check we can add an always-on
power well for these platforms and call the power domain functions
unconditionally. For always-on power wells we only increase/decrease
their refcounts, otherwise they are nop.
This makes high level driver code more readable and as a bonus provides
some idea of the current power domains state for all platforms (once
the relevant debugfs entry is added).
v3: rename intel_power_wells to i9xx_always_on_power_well (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of using a separate function to check whether a power domain is
is always on, add an always-on power well covering all these power
domains and do the usual get/put on these unconditionally. Since we
don't assign a .set handler for these the get/put won't have any effect
besides the adjusted refcount.
This makes the code more readable and provides debug info also on the
use of always-on power wells (once the relevant debugfs entry is added.)
v3: make is_always_on to be bool instead of a bit field (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW generations so far had only one always-on power well and optionally
one dynamic power well. Upcoming HW gens may have multiple dynamic power
wells, so add some infrastructure to support them.
The idea is to keep the existing power domain API used by the rest of
the driver and create a mapping between these power domains and the
underlying power wells. This mapping can differ from one HW to another
but high level driver code doesn't need to know about this. Through the
existing get/put API it would just ask for a given power domain and the
power domain framework would make sure the relevant power wells get
enabled in the right order.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way the code is simpler and can also be used for other platforms
where the audio power domain->power well mapping is different.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SNB has another register where the actual FBC CPU fence number is
stored. The documenation explicitly states that the fence number
in DPFC_CTL must be 0 on SNB. And in fact when it's not zero,
the GTT tracking simply doesn't work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other .enable_fbc() funcs use plane_name(). Make
gen7_enable_fbc() do the same.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This regression has been introduced in
commit 4fe8590a92
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Sep 4 18:25:22 2013 +0300
drm/i915: Use adjusted_mode appropriately when computing watermarks
I guess we should renable the enabled local variable into something a
notch more descriptive, but that's something for -next.
The effect on my i945gme netbook is pretty severe amounts of underruns
- usually the very first pixel gets used for the entire screeen.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 351aa5666d.
It breaks rc6 on at least one snb machine. Since we don't yet have a
report for ivb let's keep it there for now.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71656
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: erik@vontaene.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe B and pipe C interrupt mask and enable registers are now part
of the pipe, so disabling the pipe power wells will lost the contests of
the registers.
Art totally debugged this one!
v2: Use the irq_lock to clarify code, and prevent future bugs (Daniel)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Make sparse happy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hold vertex data in cache until last reference
BDW-A workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW-A workaround
BDW Bug #1899532
v2: WARN on when not using preliminary HW support
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This implements a workaround for PSR dealing with some vblank issue.
WaPsrDPAMaskVBlankInSRD && WaPsrDPRSUnmaskVBlankInSRD
v2: forgot to git add bogus whitespace fix
v3: Update with workaround names.
Use for_each_pipe() and CHICKEN_PIPESL_1(pipe) macro (Ville)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Kill redundant IS_BDW check and remove the copious amount of
uneeded lines added.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is mostly what we have for HSW with the exceptions of:
no writes:
GEN6_RC1_WAKE_RATE_LIMIT
GEN6_RC6pp_WAKE_RATE_LIMIT
GEN6_RC1e_THRESHOLD
GEN6_RC6p_THRESHOLD
GEN6_RC6pp_THRESHOLD
GEN6_RP_DOWN_TIMEOUT - use 1s instead of 1.28s
Don't try to overclock, or program ring/IA frequency tables since we
don't quite have sufficient docs yet.
NOTE: These values do not reflect the changes made recently by Chris.
Since we have no evidence yet what the proper way to tweak for this
platform is, I think it is good to go, and can be optimized by Chris, or
whomever, later.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk and drop TODO - having per-platform rps
register frobbing code is in my opinion preferred, now that all the
infrastructure functions are extracted.]
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current formula we use for HSW is not what is in current docs.
However, changing to the HSW formula on my HSW does not improve power
usage, and decreases performance by about 5% in limited xonotic testing.
For gen8, until we know otherwise, or run experiments, let's use
the HSW formula - which should be the same used in the Windows driver
(and thus help make an apples-applies comparison) on gen8.
v2: Use >= 8 instead of > 7 to be consistent with all other gen
checks.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has bigger display FIFOs than Haswell. Otherwise the
two are very similar.
v2: Fix FBC WM_LP shift for BDW
v3: Rebase on top of the big Haswell wm rework.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 also needs this workaround.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a generic comment that we need to recheck all these w/a.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like Haswell, but with the small twist that the panel fitter for pipe A is
now also in the always-on power well.
v2: Use the new HAS_POWER_WELL macro.
v3: Rebase on top of intel_using_power_well patches.
v4: This time actually update the PFIT check correctly so that the
pipe A pfit is in the always-on domain.
v5: Rebase on top of the VGA power domain addition.
v6: Rebase on top of the new power domain infrastructure. Also pimp the commit
message a bit while at it.
v7: Use IS_BROADWELL instead of IS_GEN8 (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock gating init is really a catch all function for registers we need
to write early in loading the driver.
Atm just the bare metal stuff we need, more will surely come.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Polling to make sure the current GPU frequency matches the last
requested frequency should not be necessay, and if there's some
throttling involved, the two might not match anyway.
Since we're still seeing this trigger occasionally, and it just
introduces a rather pointless 10 ms delay, it seems like better
to kill it off.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
