DESHDCP clock is needed on DRA7 based SoCs to enable the DSS IP. That
clock is an odd one, as it is not supposed to be any kind of core clock
for DSS, and we don't even support HDCP, but the clock is still needed
even for the HWMOD framework to be able to reset the DSS IP.
As there's no support for multiple core clocks in the HWMOD framework,
we don't have any obvious place to enable this clock when DSS IP is
being enabled.
Furthermore, the HDMI on OMAP5 DSS is the same as on DRA7, and OMAP5
does not have any such clock configuration bit. This suggests that on
OMAP5 the DESHDCP clock is always enabled, and for DRA7 we have the
possibility to gate it.
So, as we don't have any clean way to enable and disable the clock
based on the need, this patch enables the clock at boot time, making it
work similarly to OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
__init markings on function prototypes are useless, so remove
them.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Define an enum for gpt timer device type in include/soc/imx/timer.h to
tell the gpt block differences among SoCs. Update non-DT users (clock
drivers) to pass the device type.
As we now have include/soc/imx/timer.h, the declaration of
mxc_timer_init() is moved into there as the best fit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to IMX6D/Q RM, table 18-3, sata clock's parent is ahb, not ipg.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for clock gating of I2C2 and I2C3.
We use I2C2 in a (not yet mainlined) device tree.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add i.MX7D clk tree support.
Enable all clock to bring up imx7.
Clock framework need be modified a little since imx7d
change clock design. otherwise system will halt and block the
other part upstream.
All clock refine need wait for Dong Aisheng's patch
clk: support clocks which requires parent clock on during operation
Or other solution ready.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enabled DAP (debug access port) by default. This enables the hw-
breakpoint framework to make use of the breakpoints and watchpoints
supported by hardware.
[ 0.215805] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.224624] hw-breakpoint: maximum watchpoint size is 4 bytes.
Without this clock, the hw-breakpoint driver claims an undefined
instruction during initialization:
[ 0.227380] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.227519] hw-breakpoint: CPU 0 failed to disable vector catch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Include the "clk.h" header file to fix the following sparse warning:
drivers/clk/imx/clk-cpu.c:77:12: warning: symbol 'imx_clk_cpu' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The definition of do_div uses unsigned long long
variable as its first parameter, better to pass
a u64 variable as first parameter when calling
do_div function.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
EPIT provides another timer implementation besides the default GPT
timer. The imx35 clock driver will use EPIT timer when option
CONFIG_MXC_USE_EPIT is enabled. However, initializing timers from
clock driver is a workaround solution and causes problem when we move
clock drivers into driver/clk.
Let's simply drop the EPIT initialization from there. If people really
want this EPIT option, EPIT timer driver needs to be reworked to do the
initialization in a standard way - use CLOCKSOURCE_OF_DECLARE() with
device tree support.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Several exported TI clock driver features are no longer needed outside
the clock driver itself, thus move all of these to the driver private
header file. Also, update some of the driver files to actually include
this header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks on the Arria 10 platform is a bit different than the
Cyclone/Arria 5 platform that it should just have it's own
driver.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are 5 possible parent clocks for the SoCFPGA Arria10. Move the define
SYSMGR_SDMMC_CTRL_SET and streq() to clk.h so that the Arria clock driver
can use.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove a previously registered clock provider when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
the hardware node includes both clock and reset support, so it
is named as "car".
this patch implements Flexible clocks(mux, divider, gate), Selectable
clock(mux, divider, gate), root clock(gate),leaf clock(gate), others.
it also implements the reset controller functionality.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The variable init (struct clk_init_data) is allocated on the stack.
We weren't initializing the .flags field, so it contains random junk,
which can cause all kinds of interesting issues when the flags are
parsed by clk_register.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Berlin clock driver was sharing a DT node with the pin controller
and the reset driver. All these devices are now sub-nodes of the chip
controller. This patch rework the Berlin clock driver to allow moving
the Berlin clock DT bindings into their own sub-node of the chip
controller node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Prepare conversion of berlin clk drivers to a simple-mfd sub-node by
checking for parent node compatible. If parent node is "syscon" compatible
use it for of_iomap instead of the own node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add initial clock support for Marvell PXA1928. The PXA1928 is a mobile
SOC and is similar to other MMP/PXA series of SOCs, so a lot of the
existing infrastructure is reused here.
Currently the PLLs are just fixed clocks, and not all leaf clocks are
implemented.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch shows the correct information for debugging when fail
to set clock rate because original error message shows the error
value instead of current clock rate.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-u300.c:1175:13: warning: symbol 'u300_clk_init' was not declared. Should it be static?
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-moxart.c:18:13: warning: symbol 'moxart_of_pll_clk_init' was not declared. Should it be static?
drivers/clk/clk-moxart.c:56:13: warning: symbol 'moxart_of_apb_clk_init' was not declared. Should it be static?
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-xgene.c:77:43: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/clk-xgene.c:77:43: expected void *csr
drivers/clk/clk-xgene.c:77:43: got void [noderef] <asn:2>*
...
drivers/clk/clk-xgene.c: In function ‘xgene_clk_enable’:
drivers/clk/clk-xgene.c:237:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
drivers/clk/clk-xgene.c:248:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/mmp/clk-apbc.c:118:16: warning: symbol 'clk_apbc_ops' was not declared. Should it be static?
drivers/clk/mmp/clk-apmu.c:64:16: warning: symbol 'clk_apmu_ops' was not declared. Should it be static?
Cc: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/versatile/clk-sp810.c:159:29: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:29: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:29: right side has type int
drivers/clk/versatile/clk-sp810.c:159:53: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:53: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:53: right side has type int
drivers/clk/versatile/clk-sp810.c:138:13: warning: symbol 'clk_sp810_of_setup' was not declared. Should it be static?
Acked: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/ti/clk.c:125:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:125:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:125:31: got void *
drivers/clk/ti/clk.c:132:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:132:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:132:31: got void *
drivers/clk/ti/dpll.c:180:14: warning: symbol '_get_reg' was not declared. Should it be static?
drivers/clk/ti/fapll.c:624:32: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:625:31: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:630:40: warning: Using plain integer as NULL pointer
drivers/clk/ti/clk-dra7-atl.c:158:22: warning: symbol 'atl_clk_ops' was not declared. Should it be static?
drivers/clk/ti/clk-dra7-atl.c:170:39: warning: Using plain integer as NULL pointer
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/st/clkgen-mux.c:134:4: warning: symbol 'clkgena_divmux_get_parent' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:171:15: warning: symbol 'clkgena_divmux_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:218:12: warning: symbol 'clk_register_genamux' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:388:13: warning: symbol 'st_of_clkgena_divmux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:488:13: warning: symbol 'st_of_clkgena_prediv_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:625:13: warning: symbol 'st_of_clkgen_mux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:702:13: warning: symbol 'st_of_clkgen_vcc_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:273:15: warning: symbol 'recalc_stm_pll800c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:300:15: warning: symbol 'recalc_stm_pll1600c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:324:15: warning: symbol 'recalc_stm_pll3200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:346:15: warning: symbol 'recalc_stm_pll1200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:565:19: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:565:19: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:565:19: got void *
drivers/clk/st/clkgen-pll.c:576:18: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:576:18: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:576:18: got void *
drivers/clk/st/clkgen-pll.c:693:53: warning: incorrect type in argument 2 (different address spaces)
drivers/clk/st/clkgen-pll.c:693:53: expected void *[noderef] <asn:2>reg
drivers/clk/st/clkgen-pll.c:693:53: got void [noderef] <asn:2>*[assigned] pll_base
drivers/clk/st/clkgen-fsyn.c:495:5: warning: symbol 'clk_fs660c32_vco_get_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-fsyn.c:522:5: warning: symbol 'clk_fs660c32_vco_get_params' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:119:15: warning: symbol 'flexgen_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:177:12: warning: symbol 'clk_register_flexgen' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:263:13: warning: symbol 'st_of_flexgen_setup' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These are __iomem pointers. Mark them appropriately so we don't
get sparse errors like
drivers/clk/sirf/clk-common.c:60:16: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/sirf/clk-common.c:60:16: expected void const volatile [noderef] <asn:2>*addr
drivers/clk/sirf/clk-common.c:60:16: got void *
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/shmobile/clk-emev2.c:37:14: warning: symbol 'smu_base' was not declared. Should it be static?
Cc: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/samsung/clk-exynos5260.c:138:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:328:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:392:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:494:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:583:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:644:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:779:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:898:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:962:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1018:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1165:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1373:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1829:40: warning: Using plain integer as NULL pointer
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/hisilicon/clk-hix5hd2.c:255:13: warning: symbol 'hix5hd2_clk_register_complex' was not declared. Should it be static?
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/berlin/berlin2-pll.c:94:12: warning: symbol 'berlin2_pll_register' was not declared. Should it be static?
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This list doesn't look to be used. Let's remove it and any
associated code that would be manipulating this list. This also
silences this error:
drivers/clk/bcm/clk-kona-setup.c:24:1: warning: symbol 'ccu_list' was not declared. Should it be static?
Reviewed-by: Alex Elder <elder@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-max-gen.c:82:16: warning: symbol 'max_gen_clk_ops' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:109:5: warning: symbol 'max_gen_clk_probe' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:183:5: warning: symbol 'max_gen_clk_remove' was not declared. Should it be static?
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk.c:2700:5: warning: symbol '__clk_get' was not declared. Should it be static?
drivers/clk/clk.c:2713:6: warning: symbol '__clk_put' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function is marked as __init, so exposing it to modules
doesn't make any sense and it isn't used by modules anyway.
drivers/clk/clk-gpio-gate.c:192:13: warning: symbol 'of_gpio_gate_clk_setup' was not declared. Should it be static?
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Printing an error on kmalloc() failures is unnecessary. Remove
the print and use *ptr in sizeof() for future-proof code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_clk_get_from_provider() returns ERR_PTR on failure. The
dra7-atl-clock driver was not checking its return value and
immediately used it in __clk_get_hw(). __clk_get_hw()
dereferences supplied clock, if it is not NULL, so in that case
it would dereference an ERR_PTR.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the following compiler warning:
drivers/clk/clk-axm5516.c: In function 'axmclk_probe':
drivers/clk/clk-axm5516.c:559:2: warning: format '%u' expects argument of type 'unsigned int', but argument 2 has type 'size_t' [-Wformat=]
pr_info("axmclk: supporting %u clocks\n", num_clks);
^
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_io_request_and map returns an error pointer, but the current code assumes
that on error the returned pointer will be NULL.
Obviously, that makes the check completely useless. Change the test to actually
check for the proper error code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MS6 and MS7 do not have the MSx_P3 field. Do the 'params.p3 == 0'
check for MS0-M5 only. See [AN619, p. 6] for details.
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The divider calculation for multisynth 6 and 7 differs from the
calculation for multisynth 0-5.
For MS6 and MS7, set MSx_P1 directly, MSx_P1=divide value
[AN619, p. 6].
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The HDA to codec clock is named hda2codec_2x, so use the proper name in
the clock table.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As opposed to round_rate(), determine_rate() can take rate constraints
into account when choosing the best rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra124, as we now have a proper driver for the EMC.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock has never been able to do anything.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To be used by clock implementations for switching to a new parent during
rate change.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add 2 clocks which were erronously forgotten by the clock framework
port, namely :
- sa1100-rtc
- irda for pxa2xx-ir:UARTCLK
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Michael Turquette <mturquette@linaro.org>
Since pxa clocks were ported to the clock framework, an ordering issue
appears between clocks and clocksource initialization. As a consequence,
the pxa timer clock cannot be acquired in pxa_timer, and is disabled by
clock framework because it is "unused".
The ordering issue is that in the kernel boot sequence :
start_kernel()
...
time_init()
-> pxa_timer()
-> here the clocksource is initialized
...
rest_init()
kernel_init()
initcalls
-> here the clocks are initialized
In the current sequence, the clocks are initialized way after pxa_timer,
which cannot acquire the OSTIMER0 clock.
To solve this issue, the clocks initialization is moved to pxa_timer(),
so that clocks are initialized before clocksource for non device-tree.
For device-tree, the standard arm time_init() will take care of the
ordering.
Reviewed-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
When registering clk-si5351 by platform_data, we should not pass struct clk
for the reference clocks. Drop struct clk from platform_data and rework the
driver to use devm_clk_get of named clock references.
While at it, check for at least one valid input clock and properly prepare/
enable valid reference clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Reported-by: Russell King <rmk+linux@arm.linux.org.uk>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We don't check to make sure the enable_lock is held across
enable/disable and we don't check if the prepare_lock is held
across prepare/unprepare. Add some asserts to catch any future
locking problems.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APEATCLK and APETRACECLK are actually scaleable so register
them as scaleable clocks.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk_dump() will dump data about all clocks in JSON
format, but it misses a newline character at the
end of the JSON string. This patch adds that missing
newline character.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[sboyd@codeaurora.org: Squelch checkpatch with seq_puts()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Before commit 035a61c314 ("clk: Make clk API return per-user
struct clk instances") we acquired the enable_lock in
__clk_set_parent_{before,after}() by means of calling
clk_enable(). After commit 035a61c314 we use clk_core_enable()
in place of the clk_enable(), and clk_core_enable() doesn't
acquire the enable_lock. This opens up a race condition between
clk_set_parent() and clk_enable(). Fix it.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clkdev_create() is a shorter way to write clkdev_alloc() followed by
clkdev_add(). Use this instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a helper to allocate and add a clk_lookup structure. This can not
only be used in several places in clkdev.c to simplify the code, but
more importantly, can be used by callers of the clkdev code to simplify
their clkdev creation and registration.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The connection id is only passed to clk_get() which is already const.
Const-ify this argument too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We want to be able to call clkdev_add_table() from non-init code, so we
need to drop the __init marker from it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_add_alias() calls clk_get() followed by clk_put() but in between
those two calls it saves away the struct clk pointer to a clk_lookup
structure. This leaves the 'clk' member of the clk_lookup pointing at
freed memory on configurations where CONFIG_COMMON_CLK=y. This is a
problem because clk_get_sys() will eventually try to dereference the
freed pointer by calling __clk_get_hw() on it. Fix this by saving away
the struct clk_hw pointer instead of the struct clk pointer so that when
we try to create a per-user struct clk in clk_get_sys() we don't
dereference a junk pointer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Staticize symbols not exported and not used outside of file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace duplicated const keyword with proper array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add missing static to local (file-scope only) symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add missing static to local (file-scope only) symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds basic clocks for MT8173, including TOPCKGEN, PLLs,
INFRA and PERI clocks.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds basic clocks for MT8135, including TOPCKGEN, PLLs,
INFRA and PERI clocks.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pericfg and infracfg units also provide reset lines to several
other SoC internal units. This adds a function which can be called
from the pericfg and infracfg initialization functions which will
register the reset controller using reset_controller_register. The
reset controller will provide support for resetting the units
connected to the pericfg and infracfg controller. The units resetted
by this controller can use the standard reset device tree binding
to gain access to the reset lines.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds common clock support for Mediatek SoCs, including plls,
muxes and clock gates.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[sboyd@codeaurora.org: Squelch checkpatch warning in clk-mtk.h]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk functions and structs declare the parent_name arrays as
'const char **parent_names' which means the parent name strings
are const, but the array itself is not. Use
'const char * const * parent_names' instead which also makes
the array const. This allows us to put the parent_name arrays into
the __initconst section.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[sboyd@codeaurora.org: Squelch 80-character checkpatch warnings]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_io_request_and map returns an error pointer, but the current code assumes
that on error the returned pointer will be NULL.
Obviously, that makes the check completely useless. Change the test to actually
check for the proper error code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Commit ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power
Management support v12") added pm support for the pl330 dma driver but
it makes the clock for the Exynos5420 MDMA0 DMA controller to be gated
during suspend and this in turn makes its parent clock aclk266_g2d to
be gated. But the clock needs to be ungated prior suspend to allow the
system to be suspend and resumed correctly.
Add GATE_BUS_TOP register to the list of registers to be restored when
the system enters into a suspend state so aclk266_g2d will be ungated.
Thanks to Abhilash Kesavan for figuring out that this was the issue.
Fixes: ae43b32 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
key/value pairs in a JSON object must be separated by a comma.
After adding the properties "accuracy" and "phase" the JSON output
of /sys/kernel/debug/clk/clk_dump is invalid.
So add the missing commas to fix it.
Fixes: 5279fc402a ("clk: add clk accuracy retrieval support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
[sboyd@codeaurora.org: Added comment in function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The gfx3d_clk_src parents configuration is incorrect. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
One of the video codec clock frequencies has incorrect divider
value. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The debugfs clk directory no longer expresses a clk tree. Update
the comments around that apporiately. Also drop comments about
prepare locks needing to be held as we have the proper
annotations with lockdep_assert_held().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the code around so that we don't need to declare function
prototypes at the start of the file. Simplify
clk_core_is_prepared() and clk_core_is_enabled() too to make the
diff easier to read.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This condition can't ever be true because this function is static
and it's always called with a non-NULL pointer.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We don't need to print error messages when allocations fail.
We'll get a nice backtrace in such situations anyway.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These functions are only used in one place. Let's squash them
into their respective callers to save some lines.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
[sboyd@codeaurora.org: Redo commit text, add NULL check in
clk_enable()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While introducing struct clk_core we tried to minimize the diff
by changing the type of 'clk' variables from struct clk to struct
clk_core without changing the names of the variables. Now that
the split is complete, the code is slightly confusing when it
mixes variables called 'clk' and variables called 'core' that are
of the same type struct clk_core. Let's be consistent and use
'core' everywhere we have a struct clk_core pointer and 'clk'
when we have a struct clk pointer.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes the wrong parent clock of sclk_apollo clock
from 'div_apollo_pll' to 'div_apollo2'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
CLK_PCLK_MONOTONIC_CNT clock had a wrong register assigned to it.
The correct register is ENABLE_PCLK_MIF_SECURE_MONOTONIC_CNT.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch removes the CONFIG_ARCH_EXYNOS5433 and then use only the
CONFIG_ARCH_EXYNOS for ARM-64bit Exynos5433 SoC.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
drivers and updates to existing ones for feature enhancements and bug
fixes. There is more churn than usual in the framework core due to the
change to introduce per-user unique struct clk pointers in 4.0. This
caused several regressions to surface, some of which were sent as fixes
to 4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers. Additionally the common clk-divider code recieved
several fixes to the way it rounds rates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2LMr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.0 are mostly new clock
drivers and updates to existing ones for feature enhancements and bug
fixes.
There is more churn than usual in the framework core due to the change
to introduce per-user unique struct clk pointers in 4.0. This caused
several regressions to surface, some of which were sent as fixes to
4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers.
Additionally the common clk-divider code recieved several fixes to the
way it rounds rates"
* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
clk: check ->determine/round_rate() return value in clk_calc_new_rates
clk: at91: usb: propagate rate modification to the parent clk
clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
clk: don't use __initconst for non-const arrays
clk: at91: change to using endian agnositc IO
clk: clk-gpio-gate: Fix active low
clk: Add PWM clock driver
clk: Add clock driver for mb86s7x
clk: pxa: pxa3xx: add missing os timer clock
clk: tegra: Use the proper parent for plld_dsi
clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
clk: tegra: Model oscillator as clock
clk: tegra: Add peripheral registers for bank Y
clk: tegra: Register the proper number of resets
clk: tegra: Remove needless initializations
clk: tegra: Use consistent indentation
clk: tegra: Various whitespace cleanups
clk: tegra: Enable HDA to HDMI clocks on Tegra124
clk: tegra: Fix a bunch of sparse warnings
clk: tegra: Fix typo tabel -> table
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
Now that the kernel provides DIV_ROUND_CLOSEST_ULL(), drop the internal
implementation and use the kernel one.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->determine_rate() and ->round_rate() can return the closest rate to the
requested one or an error code.
clk_calc_new_rates is assuming these functions can't return a negative
value, which leads to a undefined behavior when the clk implementation
returns such an error code.
Fix this by returning NULL in case ->determine_rate() or ->round_rate()
returned an error code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The at91sam9n12 and at91sam9x5 usb clocks do not propagate rate
modification requests to their parents.
This causes a bug when the PLLB is left uninitialized by the bootloader
(PLL multiplier set to 0, or in other words, PLL rate = 0 Hz).
Implement the determinate_rate method and propagate the change rate
request to the parent clk.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 42773b28e7 ("clk: samsung: exynos4: Enable ARMCLK
down feature") enabled ARMCLK down feature on all Exynos4
SoCs. Unfortunately on Exynos4210 SoC ARMCLK down feature
causes a lockup when ondemand cpufreq governor is used.
Fix it by limiting ARMCLK down feature to Exynos4x12 SoCs.
This patch was tested on:
- Exynos4210 SoC based Trats board
- Exynos4210 SoC based Origen board
- Exynos4412 SoC based Trats2 board
- Exynos4412 SoC based Odroid-U3 board
Cc: Daniel Drake <drake@endlessm.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Fixes: 42773b28e7 ("clk: samsung: exynos4: Enable ARMCLK down feature")
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The statement
static const char *name[];
defines a modifiable array of pointers to constant chars. That is
*name[0] = 'f';
is forbidden, but
name[0] = "f";
is not. So marking an array that is defined as above with __initconst is
wrong. Either an additional const must be added such that the whole
definition reads:
static const char *const name[] __initconst;
or where this is not possible __initdata must be used.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These are mostly cleanups that I've been carrying in my local tree for
far too long. In addition to those, there are some preparatory patches
for the upcoming Tegra210 support and a patch to enable clocks needed
for HDMI audio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4zxP
-----END PGP SIGNATURE-----
Merge tag 'clk/for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk/tegra: Changes for v4.1-rc1
These are mostly cleanups that I've been carrying in my local tree for
far too long. In addition to those, there are some preparatory patches
for the upcoming Tegra210 support and a patch to enable clocks needed
for HDMI audio support.
The active low flag in the DT cell is currently ignored.
This occurs because of_get_named_gpio_flags() does not apply the flags
to the underlying struct gpio_desc so the test in clk_register_gpio_gate()
was bogus.
Note that this patch changes the internal kernel API for
clk_register_gpio_gate() but there are currently no other users.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The CRG11 clock controller is managed by remote f/w.
This driver simply maps Linux CLK ops onto mailbox api.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <vincent.yang@socionext.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@socionext.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The pxa3xx scheduler relies on the pxa-timer, which requires a clock for
its rate. As the clock handling will be taken over by the clock
framework, add this missing clock.
The miss was discovered by attempting to run a zylonite platform in a
device-tree configuration, with the future patch to shift clocks
handling to clock framework applied.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The current parent, plld_out0, does not exist. The proper name is
pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to
be more consistent with other clock names.
Fixes: b270491eb9 ("clk: tegra: Define PLLD_DSI and remove dsia(b)_mux")
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no reason why Tegra114 cannot use the same generic code to set
up the oscillator, clk_m and pll_ref clocks. The only effective change
that this causes is that the CLK_SET_PARENT_RATE flag is dropped, but
since these clocks are all fixed it is not needed anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the Tegra clock driver simplifies the clock tree somewhat by
taking advantage of the fact that clk_m runs at the same frequency as
the oscillator. While that's true on all currently supported SoCs, it
does not apply to Tegra210 anymore. On Tegra210 clk_m is typically
divided down from the oscillator frequency. To support that setup, add
a separate clock for the oscillator that both clk_m and pll_ref derive
from.
Modify the tegra_osc_clk_init() function to take an additional divider
parameter for clk_m. Existing SoCs always pass in 1, whereas Tegra210
will read the divider from a register in the clock & reset controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Fixes: 6d5b988e7d ("clk: tegra: implement a reset driver")
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ret variable is often explicitly initialized to 0, but there is no
need to do so in many cases because it will immediately be overwritten
with the return value from a function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the .dev_id entries in the devclks table were oddly indented.
Make them consistent with the rest of the table.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks used for HDMI audio played through the HDA controller.
Initialize the codec clock to 48Mhz and the HDA clock to 102MHz per
the TRM.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The second to last parameter of the TEGRA_CLK_PERIPH macro denotes a
table and should therefore users should pass in NULL instead of 0.
Fixes a bunch of sparse warnings like this:
warning: Using plain integer as NULL pointer
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock initialization structure is named struct clk_init_table.
Update the kerneldoc comment to use the correct name.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Put NULL test on the result of the previous call instead on one of its
arguments. A simplified version of the semantic match that finds this
problem is as follows (http://coccinelle.lip6.fr/):
// <smpl>
r@
expression *e1;
expression *e2;
identifier f;
statement S1,S2;
@@
e1 = f(...,e2,...);
(
if (e1 == NULL || ...) S1 else S2
|
*if (e2 == NULL || ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we introduced the parent_map tables, we missed to update
some of the functions where mapping is translated. Fix this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Support for Qualcomm's clock controllers should be available only
on Qualcomm platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The NAND controller within EBI2 requires EBI2_CLK and
EBI2_ALWAYS_ON_CLK clocks. Create structs for these clocks so
that they can be used by the NAND controller driver. Add an entry
for EBI2_AON_CLK in the gcc-ipq806x DT binding document.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
__initdata updated to __initconst for
static const struct of_device_id ti_clkdm_match_table[]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Register the clock gates for the external audio and ethernet
reference clocks provided by the top-level general control block.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the system interface gate clocks provided by the peripheral
general control block. These clocks gate register access for various
peripherals.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9322/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the clocks generated by the peripheral clock controller.
This includes the clocks for several peripherals, including I2C,
PWM, watchdog, and timer.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the clocks generated by the core clock controller.
This includes the 7 PLLs and clocks for the CPU, RPU co-processor,
audio, WiFi, bluetooth, and several other peripherals.
The MIPS and PERIPH_SYS clocks must remain enabled at all times.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a driver for the integer (GF40LP_LAINT) and fractional (GF40LP_FRAC)
PLLs present on Pistachio.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add clock controller for CMU ISP clock domain on Exynos3250,
providing clocks for FIMC-IS subsystem.
[b.michalska: use samsung_cmu_register_one to register
the provider; updated DT binding documentation]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[s.nawrocki: added __init attribute which was missing in function
exynos3250_cmu_platform_init() in function, which has been]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch add CLKOUT driver support for Exynos3250 SoC.
Exynos3250 SoC PMU_DEBUG is the same with Exynos4's PMU_DEBUG
including CLKOUT mux. So we can use the exynos4's clkout init
function for Exynos3250 without the need to add new function.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Replace doubled const in the arrays of clock names with proper const
pointer to const data. This fixes the warnings:
drivers/clk/clk-si5351.c:71:25: warning: duplicate const
drivers/clk/clk-si5351.c:74:25: warning: duplicate const
drivers/clk/clk-si5351.c:77:25: warning: duplicate const
drivers/clk/clk-si5351.c:80:25: warning: duplicate const
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/qcom/clk-pll.c:74:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These frequency tables list the wrong rates. Either they don't
have the correct frequency at all, or they're specified in kHz
instead of Hz. Fix it.
Fixes: c99e515a92 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver"
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The usual round of clock changes for the Allwinner SoCs.
There is nothing really standing out here, but a few changes and fixes, most
notably to allow the AHB clock to be parented to a PLL, instead of the CPU
clock to avoid any AHB rate change due to cpufreq.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVEyS7AAoJEBx+YmzsjxAgKRIP/3cn2AYWL25NGB2vd61hYQuK
zHMHqqGyybr+8nxCd2ue4ztBLUTMZz3BA+siaYG7KzOUmSCpHZb6ic2RlqWGZMbX
CmBW09YNiMtXvIaViYXH8ltVy/Ug8abwpRVkPjWf8jcbN9beGb34mrYstUBa4Cmh
9clMaMTAvhD0KqmrlHGd/tgyXdZXZPriRLLbUbumF5gatXFpHK2EzJBQMqAzhPE+
Qrn5xoDJMBziJ21cX/4MRnGWILgOy9EioW7TMhUvj7reZniHhkTBiSo/gu6qImTM
izkO1GP5rAhVjfEbltvVPIKaFP2cFnxwVwq9sDkhE4cMwb9CWOXhM6vdEFRm9PAG
nC/VVjLFaJ3lCyI+jYB5917d+U/F+RwrI07Zwx9+QLzNiyCh9y2DL+kKT6iyzYbY
as4Jg4J2MrOk+WesGH49PAT/ciUqnViTMKMMcbu/0chMHIsN7L80h+gH9ktnAkN4
1JmQfL2A85i2NORsb7SFM4P5Gc8c5cxnqbZ4honS4TxLW5CmXI9zISG53j/miBy9
SRutVT6IGseMNhIrWgHxRVVQBpG3QasYZSVOVutK9IDrUJ8L0pgymb7VjtMaAKDK
1dxfl6gdkUIJ1jfjD3ly57eMkikLDWc/ea3VgIUCQoBU8IVJuJuc/miWi0i3qnJo
zkLzG1fR0OH+LHtFO42K
=k3yP
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.1' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clocks changes for 4.1
The usual round of clock changes for the Allwinner SoCs.
There is nothing really standing out here, but a few changes and fixes, most
notably to allow the AHB clock to be parented to a PLL, instead of the CPU
clock to avoid any AHB rate change due to cpufreq.
The pll6 has a /4 output that is used as an input to the ahb mux clock.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current sunxi clock driver has the base factor clock of divs clocks
as the last clock output of the clock node. This makes it rather difficult
to add new outputs, such as fixed dividers, which were previously unknown.
This patch makes the divs clocks data structure specify which output is
the factor clock, and updates all current divs clocks accordingly.
We can then add new outputs after the factor clocks, at least not breaking
backward compatibility with regards to the devicetree bindings.
Also replace kzalloc with kcalloc in sunxi_divs_clk_setup().
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we have a fractional divider for the synthesizer, just implement
a simple multiply logic for the PLL.
It seems the PLL divider needs to have also the multiplier set for the PLL
to lock. At least I have not yet figured out if divided rates are doable.
So let's just ignore the PLL divider for now as the synthesizer has both
integer and fractional dividers so we don't even need to use the PLL
divider for the rates we know work with PLL locking.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We can pretty much get any rate out of the FAPLL because of the fractional
divider. Let's first try just adjusting the post divider, and if that is
not enough, then reprogram both the fractional divider and the post divider.
Let's also add a define for the fixed SYNTH_PHASE_K instead of using 8.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need to round the calculated value to have it match the requested rate.
While at it, let's fix a typo and use a define for SYNTH_MAX_DIV_M as we
will need it in later patches for set_rate.
And let's remove two unused includes.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The OMAP DMTimer API, omap_dm_timer_set_source(), uses the clock name
timer_sys_ck for setting a timer's clock source for the source index
OMAP_TIMER_SRC_SYS_CLK. There is currently no clock alias data for
the Timers 13 through 16 for this clock name, so add the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The OMAP DMTimer API, omap_dm_timer_set_source(), can set the parent
of a timer node using 3 different values that use fixed parent names
for the clocks. The parent name, timer_sys_ck, is used for setting the
parent when used with the source index OMAP_TIMER_SRC_SYS_CLK. This
should point to the TIMER_SYS_CLK and not the SYSCLKIN2, so correct
the clock aliases appropriately. SYSCLKIN2 is not a mandatory clock
input.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for Timers use the legacy (non-DT) device
names and a source clock named sys_ck. OMAP5 is DT-boot only,
so correct the DT clock aliases to use the DT device names
instead. Also, the source clock name is corrected from 'sys_ck'
to 'timer_sys_ck', the name used by the OMAP dmtimer driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for timers using the legacy OMAP timer
device names have been cleaned up. These device names reflect
the names used in legacy boot, and are no longer applicable
as OMAP4 is DT boot only now.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Add missing mcbsp clock aliases.
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In DT boot we do not have devices named as omap-mcbsp.X.
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is a case where NULL can be a valid return value for
ti_clk_get_reg_addr, specifically the case where both the provider index
and register offsets are zero. In this case, the current error checking
against a NULL pointer will fail. Thus, change the API to return a
ERR_PTR value in an error case, and change all the users of this API to
check against IS_ERR instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
This patch adds support for the global clock controller found on the MSM8916
based devices. It allows the various device drivers to probe and control
their clocks and resets.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Removed NULL entry from parent_maps]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently configure_bank() returns void. Add some error
checking on the regmap calls and propagate if there is
any error.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the common clock framework API, the clk_get_parent() function
should return u8. Currently we are returning negative values on error. Fix
this and use the default parent in case of an error.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock
generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to reparent AHB clock to PLL6 on sun5i/sun7i using the assigned
clocks properties. AHB is a factor clock, while PLL6 is a divs clock.
Register divs clocks before factor clocks so reparenting works. This
is only needed because we do the reparenting on the clock provider.
The proper way to fix this is to split out all the old sunxi clocks
into separate CLK_OF_DECLARE statements, like we are doing for sun9i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the ahb clock on sun5i/sun7i is muxable, ahb is no longer
guaranteed to be a child of the cpu clock. Add the cpu clock to
the list of protected clocks so it doesn't get disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AHB clock on sun5i and sun7i are muxable divider clocks.
Use a factors clock to support them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
driver fixes for new regressions since v3.19. Second are fixes to the
common clock divider type caused by recent changes to how we round clock
rates. This affects many clock drivers that use this common code.
Finally there are fixes for drivers that improperly compared struct clk
pointers (drivers must not deref these pointers). While some of these
drivers have done this for a long time, this did not cause a problem
until we started generating unique struct clk pointers for every
consumer. A new function, clk_is_match was introduced to get these
drivers working again and they are fixed up to no longer deref the
pointers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nc5C
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
of_clk_get_by_clkspec() has the same function signature as
of_clk_get_from_provider()
struct clk *of_clk_get_by_clkspec(struct of_phandle_args
*clkspec)
struct clk *of_clk_get_from_provider(struct of_phandle_args
*clkspec)
except of_clk_get_by_clkspec() checks to make sure clkspec is not
NULL. Let's remove of_clk_get_by_clkspec() and replace the
callers of it (clkconf.c) with of_clk_get_from_provider().
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The child_node member of struct clk is named the same as the
child_node member of struct clk_core. Let's rename the struct
clk's member to clks_node to avoid getting confused with the
child_node member of struct clk_core and to match the name of the
list head, clks.
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Alban Browaeys <alban.browaeys@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The ahbix clock can never be turned off in practice. To change the
rates we need to switch the mux off the M/N counter to an always on
source (XO), reprogram the M/N counter to get the rate we want and
finally switch back to the M/N counter. Add a new ops structure
for this type of clock so that we can set the rate properly.
Fixes: c99e515a92 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver"
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PXO is 25MHz, not 27MHz. Fix the table.
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global
clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
If a driver calls clk_set_parent(clk, parent) and parent is the
current parent of clk we shouldn't fail in any case.
Unfortunately if clk is a read-only mux we return -ENOSYS
because we think we can't change the parent, except for in this
special case where we don't actually need to change the parent at
all. Return 0 in such a situation.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
It's useful to have tracepoints around operations that change the
hardware state so that we can debug clock hardware performance
and operations. Four basic types of events are supported: on/off
events for enable, disable, prepare, unprepare that only record
an event and a clock name, rate changing events for
clk_set_{min_,max_}rate{_range}(), phase changing events for
clk_set_phase() and parent changing events for clk_set_parent().
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
If a clock's clk_ops doesn't have the set_phase op set we should
return an error from clk_set_phase(). This way clock consumers
know that when they tried to set a phase it didn't work, as
opposed to the current behavior where the return value is 0
meaning success.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
If the divider or multiplier values are 0 in the register, bypassing the
divider and returning the parent clock rate in clk_fd_recalc_rate().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed commitlog typo]
Add lockdep asserts for holding the prepare_lock to all functions
marking this as a requirement in description. Add this to private and
exported functions so all locking misuse could be detected during
debugging.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some drivers compare struct clk pointers as a means of knowing
if the two pointers reference the same clock hardware. This behavior is
dubious (drivers must not dereference struct clk), but did not cause any
regressions until the per-user struct clk patch was merged. Now the test
for matching clk's will always fail with per-user struct clk's.
clk_is_match is introduced to fix the regression and prevent drivers
from comparing the pointers manually.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[arnd@arndb.de: Fix COMMON_CLK=N && HAS_CLK=Y config]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[sboyd@codeaurora.org: const arguments to clk_is_match() and
remove unnecessary ternary operation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Similar to the reasoning for the previous commit
DIV_ROUND_CLOSEST(parent_rate, rate)
might not be the best integer divisor to get a good approximation for
rate from parent_rate (given the metric for CLK_DIVIDER_ROUND_CLOSEST).
For example assume a parent rate of 1000 Hz and a target rate of 700.
Using DIV_ROUND_CLOSEST the suggested divisor gets calculated to 1
resulting in a target rate of 1000 with a delta of 300 to the desired
rate. With choosing 2 as divisor however the resulting rate is 500 which
is nearer to 700.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbe (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbe (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit bca9690b94 ("clk: divider: Make generic for usage elsewhere")
returned only the divider value for read-only dividers instead of the
actual rate.
Fixes: bca9690b94 ("clk: divider: Make generic for usage elsewhere")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The irq line used by the PMC block is shared with several peripherals
including the init timer which is registering its handler with
IRQF_NO_SUSPEND.
Implement the appropriate suspend/resume callback for the PMC irqchip,
and inform irq core that PMC irq handler can be safely called while
the system is suspended by setting IRQF_COND_SUSPEND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit adds a new clock driver for the Marvell Armada 39x family
of processors. This driver is fairly similar to the ones already used
on other Marvell EBU processors, with the following main differences:
* Different set of ratios
* Different set of core clocks
* Configurable reference clock in frequency
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 39x, contrary to its predecessor, has a configurable
reference clock frequency, of either 25 Mhz, or 40 Mhz. For the
previous SoCs, it was fixed to 25 Mhz and described directly as such
in the Device Tree.
For Armada 39x, we need to read certain registers to know whether the
frequency is 25 or 40 Mhz. Therefore, this commit extends the common
mvebu clock code to allow the SoC-specific code to say it wants to
register a reference clock, by giving a non-NULL ->get_refclk_freq()
function pointer in its coreclk_soc_desc structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Driver for the r8a7778's clocks that depend on the mode bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
drivers/clk/qcom/lcc-msm8960.c:577:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
drivers/clk/qcom/lcc-ipq806x.c:465:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This clock is needed for most audio clock frequencies. Add it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
regmap_read() returns 0 on success, not the value of the register
that is read. Fix it so we properly detect the frequency plan.
Fixes: b82875ee07 "clk: qcom: Add MSM8960/APQ8064 LPASS clock
controller (LCC) driver"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These shifts were copy/pasted from the pcm which is a different
size RCG. Use the correct offsets so that slimbus rates are
correct.
Fixes: b82875ee07 "clk: qcom: Add MSM8960/APQ8064 LPASS clock controller (LCC) driver"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 163152cbbe ("clk: ti: Add support for FAPLL on dm816x")
added basic support for the FAPLL on dm818x, but has a bug for the
parent PLL enable bit. The FAPLL_MAIN_PLLEN is defined as BIT(3)
but the code is doing a shift on it.
This means the parent PLL won't get disabled even if all it's child
synthesizers are disabled.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The USB controller/phy clocks and reset controls are in a separate
address block, unlike previous SoCs where they were in the clock
controller. Also, access to the address block is controlled by a
clock gate to AHB.
Add support for resets requiring a clock to be enabled when
asserting/deasserting the reset controls, and add the sun9i USB
clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB clocks originally shared code with the gates clocks, but had
additional reset controllers. Move these to a separate file. This will
allow us to add new support for slightly different USB clocks, such as
on the A80, without affecting gates clocks, and also facilitate the
migration of gates clocks to a generic solution.
This also cleans up the USB clocks code slightly, such as adding
newlines, getting rid of the unused clkdev call, using a simple
u32 instead of BITMAP for the clock masks, using BIT() macro to
declare the clock bitmasks, and using of_io_request_and_map() to
get the I/O address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
We don't really need to recalculate the effective rate of a clock when a
per-user clock is removed, if the constraints of the later aren't
limiting the requested rate.
This was causing problems with clocks that never had a rate set before,
as rate_req would be zero. Though this could be considered a bug in the
implementation of those clocks, this should be checked somewhere else.
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Revert commit 039e597075 (clk: mxs: Fix invalid 32-bit access to frac
registers), because it leads to a faulty spi communication on mx28evk.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clock passed as an argument to clk_mux_determine_rate_flags()
has the CLK_SET_RATE_PARENT flag set but it has no parent, then a
NULL pointer will tried to be dereferenced.
This shouldn't happen since setting that flag for a clock with no
parent is a bug but the core should be robust to handle that case.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
Clock subsystem frequently performs duplication of strings located in
read-only memory section. Replacing kstrdup by kstrdup_const allows to
avoid such operations.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
of_clk_get_by_clkspec() returns a struct clk pointer but it
doesn't create a new handle for the consumers when we're using
the common clock framework. Instead it just returns whatever the
clk provider hands out. When the consumers go to call clk_put()
we get an Oops.
Unable to handle kernel paging request at virtual address 00200200
pgd = c0004000
[00200200] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc1-00104-ga251361a-dirty #992
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: ee00b000 ti: ee088000 task.ti: ee088000
PC is at __clk_put+0x24/0xd0
LR is at clk_prepare_lock+0xc/0xec
pc : [<c03eef38>] lr : [<c03ec1f4>] psr: 20000153
sp : ee089de8 ip : 00000000 fp : 00000000
r10: ee02f480 r9 : 00000001 r8 : 00000000
r7 : ee031cc0 r6 : ee089e08 r5 : 00000000 r4 : ee02f480
r3 : 00100100 r2 : 00200200 r1 : 0000091e r0 : 00000001
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 4000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee088238)
Stack: (0xee089de8 to 0xee08a000)
9de0: ee7c8f14 c03f0ec8 ee089e08 00000000 c0718dc8 00000001
9e00: 00000000 c04ee0f0 ee7e0844 00000001 00000181 c04edb58 ee2bd320 00000000
9e20: 00000000 c011dc5c ee16a1e0 00000000 00000000 c0718dc8 ee16a1e0 ee2bd1e0
9e40: c0641740 ee16a1e0 00000000 ee2bd320 c0718dc8 ee1d3e10 ee1d3e10 00000000
9e60: c0769a88 00000000 c0718dc8 00000000 00000000 c02c3124 c02c310c ee1d3e10
9e80: c07b4eec 00000000 c0769a88 c02c1d0c ee1d3e10 c0769a88 ee1d3e44 00000000
9ea0: c07091dc c02c1eb8 00000000 c0769a88 c02c1e2c c02c0544 ee005478 ee1676c0
9ec0: c0769a88 ee3a4e80 c0760ce8 c02c150c c0669b90 c0769a88 c0746cd8 c0769a88
9ee0: c0746cd8 ee2bc4c0 c0778c00 c02c24e0 00000000 c0746cd8 c0746cd8 c07091f0
9f00: 00000000 c0008944 c04f405c 00000025 ee00b000 60000153 c074ab00 00000000
9f20: 00000000 c074ab90 60000153 00000000 ef7fca5d c050860c 000000b6 c0036b88
9f40: c065ecc4 c06bc728 00000006 00000006 c074ab30 ef7fca40 c0739bdc 00000006
9f60: c0718dbc c0778c00 000000b6 c0718dc8 c06ed598 c06edd64 00000006 00000006
9f80: c06ed598 c003b438 00000000 c04e64f4 00000000 00000000 00000000 00000000
9fa0: 00000000 c04e64fc 00000000 c000e838 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 c0c0c0c0 c0c0c0c0
[<c03eef38>] (__clk_put) from [<c03f0ec8>] (of_clk_set_defaults+0xe0/0x2c0)
[<c03f0ec8>] (of_clk_set_defaults) from [<c02c3124>] (platform_drv_probe+0x18/0xa4)
[<c02c3124>] (platform_drv_probe) from [<c02c1d0c>] (driver_probe_device+0x10c/0x22c)
[<c02c1d0c>] (driver_probe_device) from [<c02c1eb8>] (__driver_attach+0x8c/0x90)
[<c02c1eb8>] (__driver_attach) from [<c02c0544>] (bus_for_each_dev+0x54/0x88)
[<c02c0544>] (bus_for_each_dev) from [<c02c150c>] (bus_add_driver+0xd4/0x1d0)
[<c02c150c>] (bus_add_driver) from [<c02c24e0>] (driver_register+0x78/0xf4)
[<c02c24e0>] (driver_register) from [<c07091f0>] (fimc_md_init+0x14/0x30)
[<c07091f0>] (fimc_md_init) from [<c0008944>] (do_one_initcall+0x80/0x1d0)
[<c0008944>] (do_one_initcall) from [<c06edd64>] (kernel_init_freeable+0x108/0x1d4)
[<c06edd64>] (kernel_init_freeable) from [<c04e64fc>] (kernel_init+0x8/0xec)
[<c04e64fc>] (kernel_init) from [<c000e838>] (ret_from_fork+0x14/0x3c)
Code: ebfff4ae e5943014 e5942018 e3530000 (e5823000)
Let's create a per-user handle here so that clk_put() can
properly unlink it and free the handle. Now that we allocate a
clk structure here we need to free it if __clk_get() fails so
bury the __clk_get() call in __of_clk_get_from_provider(). We
need to handle the same problem in clk_get_sys() so export
__clk_free_clk() to clkdev.c and do the same thing, except let's
use a union to make this code #ifdef free.
This fixes the above crash, properly calls __clk_get() when
of_clk_get_from_provider() is called, and cleans up the clk
structure on the error path of clk_get_sys().
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Alban Browaeys <prahal@yahoo.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch fixes the bug of CLK_SCLK_HDMI_SPDIF_DISP clock because this clock
should be included in CMU_TOP domain. So, this patch moves the CLK_SCLK_HDMI_
SPDIF_DISP clock from CMU_MIF to CMU_TOP domain.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_CAM1 domain which
generates the clocks for Cortex-A5/MIPI_CSIS2/FIMC-LITE_C/FIMC-FD IPs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_CAM0 domain which
generates the clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} IPs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_ISP domain which
generates the clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_HEVC domain which
generates the clocks for HEVC(High Efficiency Video Codec) decoder IP.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_MFC domain which
generates the clocks for MFC(Multi-Format Codec) IP.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_APOLLO domain
which generates the clocks for Cortex-A53 Quad-core processsor.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
[s.nawrocki@samsung.com: Renamed pclk_pmu_sysreg_apollo to pclk_sysreg_apollo]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Anyone may call clk_round_rate() with a zero rate value, so we have to
protect against that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch adds the mux/divider/gate clocks for CMU_FSYS domain which
contains the clocks of USB/UFS/SDMMC/TSI/PDMA IPs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_BUS{0|1|2} domains
which contain global data buses clocked at up the 400MHz. These blocks
transfer data between DRAM and various sub-blocks. These clock domains
also contain global peripheral buses clocked at 67/111/200/222/266/333/400
MHz and used for register accesses.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks for CMU_AUD domain which
includes the clocks of Cortex-A5/Bus/Audio clocks.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the the mux/divider/gate clocks for CMU_DISP domain
which includes clocks of the display IPs (DECON/HDMI/DSIM/MIXER).
Also, CMU_DISP requires 'sclk_hdmi_spdif_disp' source clock from CMU_TOP
domain. This patch adds the clocks of CMU_TOP related to HDMI.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the mux/divider/gate clocks of CMU_MIF domain which includes
the clocks for DMC(DRAM memory controller) and CCI(Cache Coherent Interconnect).
The CMU_MIF domain provides the source clocks for CMU_DISP/CMU_BUS2.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds ths mux/divider/gate clocks of CMU_G2D domain which
includes G2D/MDMA IPs. The CMU_G2D requires its parent defined in
the CMU_TOP domain. Hence this patch adds G2D related clocks to the
CMU_TOP domain.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds missing gate clocks of CMU_PERIS domain
which includes TMU/TZPC/SECKEY/CHIPID/TOPRTC/EFUSE IPs.
The special clocks of CMU_PERIS use oscclk source clock directly.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds missing divider/gate clocks of CMU_PERIC domain
which includes I2S/PCM/SPDIF/PWM/SLIMBUS IPs. The SPI/I2S may use
external input clock which has 'ioclk_*' prefix.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[ideal.song: Change clk flags of to pclk_gpio_* clk, pclk_gpio_* should be always on]
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds support for the CMU (Clock Management Units) of Exynos5433
which is an Octa-core 64bit SoC. This patch supports necessary clocks
(PLL/MMC/UART/MCT/I2C/SPI) for kernel boot and includes binding documentation
for Exynos5433 clock controller.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
[s.nawrocki@samsung.com: whitespace cleanup in dt-bindings/clock/exynos5433.h]
[ added U suffix to first arguments of PLL_35XX_RATE()]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
According to i.MX23 and i.MX28 reference manual [1],[2] the fractional
clock control register is 32-bit wide, but is separated in 4 parts.
So write instructions must not apply to more than 1 part at once.
The clk init for the i.MX28 violates this restriction and all the other
accesses on that register suggest that there isn't such a restriction.
This patch restricts the access to this register to byte instructions and
extends the comment in the init functions.
Btw the imx23 init now uses a R-M-W sequence just like imx28 init
to avoid any clock glitches.
The changes has been tested with a i.MX23 and a i.MX28 board.
[1] - http://cache.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
[2] - http://cache.freescale.com/files/dsp/doc/ref_manual/MCIMX28RM.pdf
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The 'ARM: OMAP3: legacy clock data move under clk driver' patch series
causes build errors when CONFIG_OMAP3 is not set:
drivers/clk/ti/dpll.c: In function 'ti_clk_register_dpll':
drivers/clk/ti/dpll.c:199:31: error: 'omap3_dpll_ck_ops' undeclared (first use in this function)
const struct clk_ops *ops = &omap3_dpll_ck_ops;
^
drivers/clk/ti/dpll.c:199:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/clk/ti/dpll.c:259:10: error: 'omap3_dpll_per_ck_ops' undeclared (first use in this function)
ops = &omap3_dpll_per_ck_ops;
^
drivers/built-in.o: In function `ti_clk_register_gate':
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_omap3430es2_dss_usbhost_wait'
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_am35xx_ipss_module_wait'
-in.o: In function `ti_clk_register_interface':
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_hsotgusb_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_dss_usbhost_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_ssi_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_am35xx_ipss_wait'
drivers/built-in.o: In function `ti_clk_register_composite':
:(.text+0x3da768): undefined reference to `ti_clk_build_component_gate'
In order to fix that problem, this patch makes the omap3 legacy code
compiled only when both CONFIG_OMAP3 and CONFIG_ATAGS are set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
and addition of clock definitions for DVFS on Exynos4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJUyPwjAAoJEE1bIKeAnHqLbcQP/RQoZLdRJqhToiWxMKzQjaEh
KPOAEBNGMOvPeVrf3Ct6r2a6elgLg6pKdYZcekupu9Vqrc0OXdHVKEM/YC7x5MEB
Wzs/cuVZyYb8lhnWa0dmUTEQp/JvYX1Ifgp2xlKFc6ZPstuxIsp2HizQIS8+xsqW
NxUIwkz1X0xyO4oLmVG7cO7co4FgSBfY3YI/PnUgDuixoX0X6eY0uNMLMS5J/5gP
wOmwDmgJop/qi7tMfghDwDemF3/WJBY8V2D/dIvCoSsFu0bGAPqPnemEuaeBCbEo
1sVrvEz60kXaJSx7A44Or2KX8cvaSPExcVmG66idYLlOW+gGXgjCRZ11A2FmzBDb
sWXMkwSNeZ3QxL6fmJuRkXYDbwHNWlKdZIjlM6+iYPjA78twUEN5tD1U1YTh0cy/
MCFmoUWJh2vpbQJiY3carcvq1NiNhALFUWrJK5zCoMybvIWrQhYBBCnZh7U1fDzo
nmxLcDr1IG6eRjOfn6Q2XVmCXjhZX3kojAh/ePEHQGl5jyspZcMm4Top93sTO9l6
SBimh5wrafK8nTQN8NeNGNr3s3CfYVURu9GdEiJJwecHnWoeFFc/Y/w7qaWorNtM
tsg7Gjk+95OgM+m8Cb8Nu8WXUyK7AYznbgldzypx7FVMQRpDW7/UjpB0lKjT7qeG
c0ScBKIXZd6RNyzHM2TJ
=rFdT
-----END PGP SIGNATURE-----
Merge tag 'v3.20-exynos-clk' of git://linuxtv.org/snawrocki/samsung into clk-next
Exynos 3250, 4415 drivers cleanup by using common code
and addition of clock definitions for DVFS on Exynos4.
So it can be used from modules such as clk-test.ko.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Private clock framework data structures should be private, surprisingly.
Now that all platforms and drivers have been updated to remove static
initializations of struct clk and struct clk_core objects and all
references to clk-private.h have been removed we can move the
definitions of these structures into drivers/clk/clk.c and delete the
header.
Additionally the ugly DEFINE_CLK macros have been removed. Those were
used for static definitions of struct clk objects. That practice is no
longer allowed.
Finally __clk_init is staticized as it is no longer declared in any
header.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Moves clock state to struct clk_core, but takes care to change as little API as
possible.
struct clk_hw still has a pointer to a struct clk, which is the
implementation's per-user clk instance, for backwards compatibility.
The struct clk that clk_get_parent() returns isn't owned by the caller, but by
the clock implementation, so the former shouldn't call clk_put() on it.
Because some boards in mach-omap2 still register clocks statically, their clock
registration had to be updated to take into account that the clock information
is stored in struct clk_core now.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: adapted clk_has_parent to struct clk_core
applied OMAP3+ DPLL fix from Tero & Tony]
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Tegra132 CAR supports almost the same clocks as Tegra124 CAR. This
patch mostly deals with the small differences.
Since Tegra132 contains many of the same PLL clock sources used on
Tegra114 and Tegra124, enable them in drivers/clk/tegra/clk-pll.c when
the kernel is configured to include Tegra132 support.
This patch is based on several patches from others:
1. a patch from Peter De Schrijver:
http://lkml.iu.edu/hypermail/linux/kernel/1407.1/06094.html
2. a patch from Bill Huang ("clk: tegra: enable cclk_g at boot on
Tegra132"), and
3. a patch from Allen Martin ("clk: Enable tegra clock driver for
tegra132").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Bill Huang <bilhuang@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
tegra_clocks_apply_init_table() needs to be called after the udelay
loop has been calibrated (see commit
441f199a37 ("clk: tegra: defer
application of init table") for why that is). On existing Tegra SoCs
this was done by calling tegra_clocks_apply_init_table() from
tegra_dt_init(). To make this also work on ARM64, we need to change
this into an initcall. tegra_dt_init() is called from
customize_machine which is an arch_initcall. Therefore this should
also work on existing 32bit Tegra SoCs.
Tested on Tegra20 (ventana), Tegra30 (beaverboard), Tegra124 (jetson TK1) and
Tegra132.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[paul@pwsan.com: tweaked the commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
As previously the names of the present clock and its parent were swapped.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Set the parent of the dsi lp clocks to pll_p and the rate
to 68MHz. The default parent is clk_m and rate is 12MHz, this
is too slow to receive data from the peripheral.
Per NVidia HW engineers, the optimal rate is 70MHz, but 68MHz
will suffice.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Since the SDMMC controller registers are accessed via the APB,
the APB must be flushed before gating the SDMMC clocks to prevent
register accesses to the SDMMC controllers after their clocks are
gated.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduces omap3 legacy clock data under clock driver. The clock data
is also in new format, which makes it possible to get rid of the
clk-private.h header. This patch also introduces SoC specific init
functions that shall be called from the low level init.
The data format used in this file has two possible evolution paths;
it can either be removed completely once no longer needed, or it will
be possible to retain the format and modify the TI clock driver to be
a loadable module at some point. The actual path to be followed
will be decided later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this. The interface clock descriptor
itself is overloading the gate clock descriptor, thus it needs to
be called from the gate setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data for OMAP3 is being moved under clock driver, thus
base support for this is needed. This patch adds basic definitions for
clock init descriptors and core infrastructure for initialization,
which will be called from the OMAP3 clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.
So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:
ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)
Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
As it has never been used.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As clk_unprepare_unused_subtree and clk_disable_unused_subtree are
always called with a valid struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Currently a mix of clk-qoriq/qoriq-clk and no prefix is used
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
drivers/clk/clk-qoriq.c:59:22: warning: symbol 'cmux_ops' was not declared. Should it be static?
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!parent_names) {
+ pr_err("%s: could not allocate parent_names\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!cmux_clk) {
+ pr_err("%s: could not allocate cmux_clk\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!subclks) {
+ pr_err("%s: could not allocate subclks\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!onecell_data) {
+ pr_err("%s: could not allocate onecell_data\n", __func__);
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
+ rc = of_property_read_string_index(np, "clock-output-names",
+ 0, &clk_name);
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
+ pr_err("Could not register clock provider for node:%s\n",
+ np->name);
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
+ rc = of_property_read_string_index(np, "clock-output-names",
+ i, &clk_name);
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
+ pr_err("Could not register clk provider for node:%s\n",
+ np->name);
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch adds the divider clock id for Exynos4 memory bus frequency.
The clock id is used for DVFS (Dynamic Voltage/Frequency Scaling)
feature of the exynos memory bus.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Move pxa25x clock drivers from arch/arm/mach-pxa to driver/clk.
In the move :
- convert to new clock framework legacy clocks
- provide clocks as before for platform data based boards
- provide clocks through devicetree with clk-pxa-dt
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The CPU_2X clock does not have a classical in-kernel user, but is,
amongst other things, required for OCM and debug access. Make sure this
clock is not mistakenly disabled during boot up by enabling it in the
platform's clock driver.
Cc: stable@vger.kernel.org # 3.11+
Fixes: 0ee52b157b 'clk: zynq: Add clock controller driver'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The set of clock changes for the 3.20 merge window, with mostly:
- Some PLL fixes for the A80 and A31
- The MMC custom phase functions are removed, and moved over to the generic
phase API.
- Add the A80 MMC clocks
Some DT changes slipped here as well, to preserve bisectability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m8K6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clock changes for 3.20
The set of clock changes for the 3.20 merge window, with mostly:
- Some PLL fixes for the A80 and A31
- The MMC custom phase functions are removed, and moved over to the generic
phase API.
- Add the A80 MMC clocks
Some DT changes slipped here as well, to preserve bisectability.
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUwT2NAAoJEPOmecmc0R2BjmsH/1Mp2vS9E9RBREhL/uuwtVlE
6FhINcpzVkDrwXGfupVbrWmzHTxKcyUbnluVPsLs0BCRqhhKSU0t+TT5j+mRMOpu
oNq/d3cp//fuBaiLr4G0jrgd/a9Gq4SsshPP6kH41r5CBN87jTt9wazX2GjNBf4C
LYsNNWj/qpXxeA/rFuMsI15ntPiFvap8Ag/5+IDCHuT9nwCLy7iI3G0MRGZ1kfGT
byOJd/FOqfAk3UJXuEgGOu27ZAOcbGLk7EL7YUdq7C70wAlUTu/8smTLqJFbXc9T
Xgum3FnYcuPZqNQSxQMXFpgyzE0q7KLyufv5gU1A4s2Ac69cD3nDVh9k1LAcu4s=
=arKA
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
The two big changes are the additional of the watchdog clock, which
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
These modules don't need to include clk-private.h. Replace the
include with clk.h because these modules are clock consumers and
also include clk-provider.h in clk/ti.h because struct
clk_hw_omap has a struct clk_hw embedded in it.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These drivers don't need to include clk-private.h. Remove the
include.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The phase setter and getter were not exported until now, which was causing
build breakages when callers were compiled as module. Export these two
functions.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add an LCC driver for MSM8960/APQ8064 that supports the i2s,
slimbus, and pcm clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add an LCC driver for IPQ806x that supports the i2s, S/PDIF, and
pcm clocks.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
[sboyd@codeaurora.org: Reworded commit text, added Kconfig
select, fleshed out Kconfig description a bit more, added pll4
configuration and reworked probe for it, added muxes, split out
dt-binding file]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add support for muxes that use regmap instead of readl/writel
directly. We don't support as many features as clk-mux.c, but
this is good enough to support getting and setting parents.
Adding a table based lookup can be added in the future if needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add support for dividers that use regmap instead of readl/writel.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Switch to using generic divider code, drop
enable/disable, reword commit text]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some devices don't use mmio to interact with dividers. Split out the
logic from the register read/write parts so that we can reuse the
division logic elsewhere.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some clock drivers want to find the closest rate on the input of
a mux instead of a rate that's less than or equal to the desired
rate. Add a generic mux function to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some of the clks can be registered & unregistered before the clk related debugfs
entries are initialized at late_initcall. In the unregister path checking for only
dentry before clk_debug_init() would lead dangling pointers in the debug clk list,
because the list is already populated in register path and the clk pointer freed in
unregister path.
The side effect of not removing it from the list is either a null pointer
dereference or if lucky to boot the system, the number of clk entries in
debugfs disappear.
We could add more checks like if (inited && !clk->dentry) but just removing
the check for dentry made more sense as debugfs_remove_recursive() seems to be
safe with null pointers. This will ensure that the unregistering clk would be
removed from the debug list in all the code paths.
Without this patch kernel would crash with log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G B 3.19.0-rc3-00007-g412f9ba-dirty #840
Hardware name: Qualcomm (Flattened Device Tree)
task: ed948000 ti: ed944000 task.ti: ed944000
PC is at strlen+0xc/0x40
LR is at __create_file+0x64/0x1dc
pc : [<c04ee604>] lr : [<c049f1c4>] psr: 60000013
sp : ed945e40 ip : ed945e50 fp : ed945e4c
r10: 00000000 r9 : c1006094 r8 : 00000000
r7 : 000041ed r6 : 00000000 r5 : ed4af998 r4 : c11b5e28
r3 : 00000000 r2 : ed945e38 r1 : a0000013 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 8020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xed944248)
Stack: (0xed945e40 to 0xed946000)
5e40: ed945e7c ed945e50 c049f1c4 c04ee604 c0fc2fa4 00000000 ecb748c0 c11c2b80
5e60: c0beec04 0000011c c0fc2fa4 00000000 ed945e94 ed945e80 c049f3e0 c049f16c
5e80: 00000000 00000000 ed945eac ed945e98 c08cbc50 c049f3c0 ecb748c0 c11c2b80
5ea0: ed945ed4 ed945eb0 c0fc3080 c08cbc30 c0beec04 c107e1d8 ecdf0600 c107e1d8
5ec0: c107e1d8 ecdf0600 ed945f54 ed945ed8 c0208ed4 c0fc2fb0 c026a784 c04ee628
5ee0: ed945f0c ed945ef0 c0f5d600 c04ee604 c0f5d5ec ef7fcc7d c0b40ecc 0000011c
5f00: ed945f54 ed945f10 c026a994 c0f5d5f8 c04ecc00 00000007 ef7fcc95 00000007
5f20: c0e90744 c0dd0884 ed945f54 c106cde0 00000007 c117f8c0 0000011c c0f5d5ec
5f40: c1006094 c100609c ed945f94 ed945f58 c0f5de34 c0208e50 00000007 00000007
5f60: c0f5d5ec be9b5ae0 00000000 c117f8c0 c0af1680 00000000 00000000 00000000
5f80: 00000000 00000000 ed945fac ed945f98 c0af169c c0f5dd2c ed944000 00000000
5fa0: 00000000 ed945fb0 c020f298 c0af168c 00000000 00000000 00000000 00000000
5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ebcc6d33 bfffca73
[<c04ee604>] (strlen) from [<c049f1c4>] (__create_file+0x64/0x1dc)
[<c049f1c4>] (__create_file) from [<c049f3e0>] (debugfs_create_dir+0x2c/0x34)
[<c049f3e0>] (debugfs_create_dir) from [<c08cbc50>] (clk_debug_create_one+0x2c/0x16c)
[<c08cbc50>] (clk_debug_create_one) from [<c0fc3080>] (clk_debug_init+0xdc/0x144)
[<c0fc3080>] (clk_debug_init) from [<c0208ed4>] (do_one_initcall+0x90/0x1e0)
[<c0208ed4>] (do_one_initcall) from [<c0f5de34>] (kernel_init_freeable+0x114/0x1e0)
[<c0f5de34>] (kernel_init_freeable) from [<c0af169c>] (kernel_init+0x1c/0xfc)
[<c0af169c>] (kernel_init) from [<c020f298>] (ret_from_fork+0x14/0x3c)
Code: c0b40ecc e1a0c00d e92dd800 e24cb004 (e5d02000)
---[ end trace b940e45b5e25c1e7 ]---
Fixes: 6314b6796e "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
- Support for the A31s
- Adding support for cpufreq using cpufreq-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JU1v
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Merge "Allwinner core changes for 3.20" from Maxime Ripard:
- Support for the A31s
- Adding support for cpufreq using cpufreq-dt
* tag 'sunxi-core-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Register cpufreq-dt for sun[45678]i
ARM: sunxi: Add "allwinner,sun6i-a31s" to mach-sunxi
Signed-off-by: Olof Johansson <olof@lixom.net>
For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old implementation of sun9i_a80_get_pll4_factors() has several issues,
it checks against 256 / 512 in various places where it should use 255 / 511,
it does the wrong thing for low frequencies which are an even multiple of
6 MHz, e.g. if you ask it for 72 MHz it will result in 144 Mhz, and it does
not take into account that n must be at least 12. Moreover it is quite hard
to read / follow it.
This commit rewrites it to be correct in all cases, and makes it much easier
to follow the code / to read.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This new function is similar to clk_set_parent(), except that it doesn't
actually change the parent. It merely checks that the given parent clock
can be a parent for the given clock.
A situation where this is useful is to check that a particular setup is
valid before switching to it. One specific use-case for this is atomic
modesetting in the DRM framework where setting a mode is divided into a
check phase where a given configuration is validated before applying
changes to the hardware.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The pclk supplying the watchdog is controlled via the SGRF register area.
Currently we don't have any clock-type handling external clock bits like
this one. Additionally the SGRF isn't even writable in every boot mode.
But still the clock control is available and in the future someone might
want to use it. Therefore define a simple clock for the time being so
that the watchdog driver can read its rate.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Process-Voltage-Temperatiure Monitor block on RK3288 has two clocks:
PVTM_CORE and PVTM_GPU.
Signed-off-by: Huang Lin <hl@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use the clock ID for usbphy480m_src so that we can find
this clock node in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull RCU updates from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide CLK support for Alphascale ASM9260 SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Debugging eMMC on upstream kernels it has been noticed that when the
targetpack configures MMC0 clock to 200Mhz (required to switch to
HS200) then everything works OK. However if the kernel sets the
clock rate using clk_set_rate, then the eMMC card initialisation
fails with timeouts. Lower clock speeds (the default being 50Mhz)
work ok, but they we fail to get good eMMC transfer rates.
Looking through the vendor kernel clock driver reveals Giuseppe
had already fixed this issue, but the patch hasn't made its way
upstream.
The issue is fixed by changing the logic to manage the pdiv and
fdiv divisors used for setting the rate inside the flexgen driver code.
Pdiv is mainly targeted for low freq results, while fdiv should be
used for divs =< 64. The other way can lead to 'duty cycle'
issues.
I have changed the original patch to keep the original behaviour
in cases where the div is >64 which matches the original comment
and patch description more closely. Although no clocks appear to hit
this case currently when booting an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
redefine variable clocks_per_pll as a struct member
If there are multiple PLL clock nodes, this variable will
get overwritten. Redefining it as a struct member can avoid that.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clocks on ti81xx are not compatible with omap3. On dm816x
the clock source is a FAPLL (Flying Adder PLL), and on dm814x
there seems to be an APLL (All Digital PLL).
Let's fix up things for dm816x in preparation for adding the
FAPLL support. As we already have a dummy ti81xx_dt_clk_init()
in place, let's use that for now to avoid adding a dependency
to the omap patches.
Later on if somebody adds dm814x support we can split the
ti81xx_dt_clk_init() clock init function as needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.
There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.
I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:
1. Setting the PLL to bypass mode also sets the child synthesizers
into bypass mode. As the bypass rate can also be generated by
the PLL in regular mode, there's no way for the child synthesizers
to detect the bypass mode based on the parent clock rate.
2. The PLL registers control the power for each of the child
syntheriser.
Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.
I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.
This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We don't need to fetch the parent index for clocks if they only
have one parent. Doing this also avoid an unnecessary allocation
for the parent cache.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
In order to fix the following section mismatch warning:
WARNING: drivers/clk/built-in.o(.data+0xe4): Section mismatch in reference from the variable ppc_corenet_clk_driver to the function .init.text:ppc_corenet_clk_probe()
The variable ppc_corenet_clk_driver references
the function __init ppc_corenet_clk_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/clk/built-in.o(.data+0x10c): Section mismatch in reference from the variable ppc_corenet_clk_driver to the variable .init.rodata:ppc_clk_ids
The variable ppc_corenet_clk_driver references
the variable __initconst ppc_clk_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
We can't just add the __init annotation to ppc_corenet_clk_driver or
remove the __init from ppc_corenet_clk_probe() and ppc_clk_ids.
So choose to use CLK_OF_DECLARE to scan and init the clock devices.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.
This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module 0 style clocks, or storage module clocks as named in the
official SDK, are almost the same as the module 0 clocks on earlier
Allwinner SoCs. The only difference is wider mux register bits.
As with earlier Allwinner SoCs, mmc module clocks are a special case
of mod0 clocks, with phase controls for 2 child clocks, output and
sample.
This patch adds support for both.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The memory allocated by basic clock divider/gate/mux (struct clk_gate,
clk_divider and clk_mux) was leaking. During driver unbind or probe
failure the driver only unregistered the clocks.
Use clk_unregister_{gate,divider,mux} to release all resources.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The common clk_register_{divider,gate,mux} functions allocated memory
for internal data which wasn't freed anywhere. Drivers using these
helpers could only unregister clocks but the memory would still leak.
Add corresponding unregister functions which will release all resources.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This reverts commit da788acb28.
That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.
CPU0 CPU1
---- ----
lock(clk_lock);
local_irq_disable();
lock(&(&i2c->lock)->rlock);
lock(clk_lock);
<Interrupt>
lock(&(&i2c->lock)->rlock);
*** DEADLOCK ***
The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]
Move at91rm9200_idle() along with at91sam9_idle() in clk/at91/pmc.c.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for PDMA0 and PDMA1 gate clks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The only difference between module clocks on different platforms is the
width of the mux register bits and the valid values, which are passed in
through struct factors_data. The phase clocks parts are identical.
This patch generalizes the setup function, so most of the code can be
reused when adding sun9i support, which has a wider mux register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we don't have any user left for our custom phase function, we can
safely remove this hack from the code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Instead of having three different clocks for the main MMC clock and the two
phase sub-clocks, which involved having three different drivers sharing the
same register, rework it to have the same single driver registering three
different clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Fixes the following sparse warnings:
drivers/clk/shmobile/clk-sh73a0.c:57:17: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable
register is for nfc. Current code use bit19 for non-exist "smemc"
incorrectly, this prevents eMMC from working due to the sdhci's
"core" clk is still gated.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Michael Turquette <mturquette@linaro.org>
All slow clk users are not properly claiming it (get + prepare + enable)
before using it.
If all users properly claiming this clock release it, the clock is
disabled, but faulty users still depends on it, and the system hangs.
This fix prevents the slow clock from being disabled, and should solve the
hanging issue, but offending drivers should be patched to properly claim
this clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add the ADSP clock support to the R-Car generation 2 CPG driver. This clock
gets derived from PLL1. The layout of the ADSPCKCR register is similar to
those of the clocks supported by the 'clk-div6' driver but the divider encoding
is non-linear, so can't be supported by that driver...
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the RCAN clock support to the R-Car generation 2 CPG driver. This clock
gets derived from the USB_EXTAL clock, dividing it by 6. The layout of the
RCANCKCR register is similar to those of the clocks supported by the 'clk-div6'
driver but has no divider field, and so can't be supported by that driver...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Driver for the R8A73A4's clocks that are too specific to be supported by a
generic driver.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
While DIV6 clocks require the divisor field to be non-zero when stopping
the clock, some clocks (e.g. ZB on sh73a0) fail to be re-enabled later
if the divisor field is changed when stopping the clock.
The reason for this is unknown.
To fix this, do not touch the divisor field if it's already non-zero.
On kzm9g, the smsc911x Ethernet controller is connected to the sh73a0
Bus State Controller, which is clocked by the ZB clock. Without this
fix, if the ZB clock is disabled during system suspend, and re-enabled
during resume, the kernel locks up when the smsc911x driver tries to
access the Ethernet registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
The cpu clock on sunxi machines is just a mux clock, which is normally
fed by the main PLL, but can be muxed to the main or low power oscillator.
Make the mux clock propagate rate changes to its parent, so we can
change the clock rate of the PLL, and thus actually implement rate
changing on the cpu clock.
This patch also removes the no reparenting limit.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With the prcm in sun6i (and some later SoCs) some mod0 clocks are instantiated
through the mfd framework, and as such do not work with of_clk_declare, since
they do not have registers assigned to them yet at of_clk_declare init time.
Silence the error on not finding registers in the of_clk_declare mod0 clk
setup method, and also register mod0-clk support as a platform driver to work
properly with mfd instantiated mod0 clocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
