This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Realising the following call pattern,
* first dccp_entail() is called to enqueue a new skb and
* then skb_clone() is called to transmit a clone of that skb,
this patch integrates both interrelated steps into dccp_entail().
Note: the return value of skb_clone is not checked. It may be an idea to add a
warning if this occurs. In both instances, however, a timer is set for
retransmission, so that cloning is re-tried via dccp_retransmit_skb().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This extends the existing wait-for-ccid routine so that it may be used with
different types of CCID. It further addresses the problems listed below.
The code looks if the write queue is non-empty and grants the TX CCID up to
`timeout' jiffies to drain the queue. It will instead purge that queue if
* the delay suggested by the CCID exceeds the time budget;
* a socket error occurred while waiting for the CCID;
* there is a signal pending (eg. annoyed user pressed Control-C);
* the CCID does not support delays (we don't know how long it will take).
D e t a i l s [can be removed]
-------------------------------
DCCP's sending mechanism functions a bit like non-blocking I/O: dccp_sendmsg()
will enqueue up to net.dccp.default.tx_qlen packets (default=5), without waiting
for them to be released to the network.
Rate-based CCIDs, such as CCID3/4, can impose sending delays of up to maximally
64 seconds (t_mbi in RFC 3448). Hence the write queue may still contain packets
when the application closes. Since the write queue is congestion-controlled by
the CCID, draining the queue is also under control of the CCID.
There are several problems that needed to be addressed:
1) The queue-drain mechanism only works with rate-based CCIDs. If CCID2 for
example has a full TX queue and becomes network-limited just as the
application wants to close, then waiting for CCID2 to become unblocked could
lead to an indefinite delay (i.e., application "hangs").
2) Since each TX CCID in turn uses a feedback mechanism, there may be changes
in its sending policy while the queue is being drained. This can lead to
further delays during which the application will not be able to terminate.
3) The minimum wait time for CCID3/4 can be expected to be the queue length
times the current inter-packet delay. For example if tx_qlen=100 and a delay
of 15 ms is used for each packet, then the application would have to wait
for a minimum of 1.5 seconds before being allowed to exit.
4) There is no way for the user/application to control this behaviour. It would
be good to use the timeout argument of dccp_close() as an upper bound. Then
the maximum time that an application is willing to wait for its CCIDs to can
be set via the SO_LINGER option.
These problems are addressed by giving the CCID a grace period of up to the
`timeout' value.
The wait-for-ccid function is, as before, used when the application
(a) has read all the data in its receive buffer and
(b) if SO_LINGER was set with a non-zero linger time, or
(c) the socket is either in the OPEN (active close) or in the PASSIVE_CLOSEREQ
state (client application closes after receiving CloseReq).
In addition, there is a catch-all case by calling __skb_queue_purge() after
waiting for the CCID. This is necessary since the write queue may still have
data when
(a) the host has been passively-closed,
(b) abnormal termination (unread data, zero linger time),
(c) wait-for-ccid could not finish within the given time limit.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This extends the packet dequeuing interface of dccp_write_xmit() to allow
1. CCIDs to take care of timing when the next packet may be sent;
2. delayed sending (as before, with an inter-packet gap up to 65.535 seconds).
The main purpose is to take CCID2 out of its polling mode (when it is network-
limited, it tries every millisecond to send, without interruption).
The interface can also be used to support other CCIDs.
The mode of operation for (2) is as follows:
* new packet is enqueued via dccp_sendmsg() => dccp_write_xmit(),
* ccid_hc_tx_send_packet() detects that it may not send (e.g. window full),
* it signals this condition via `CCID_PACKET_WILL_DEQUEUE_LATER',
* dccp_write_xmit() returns without further action;
* after some time the wait-condition for CCID becomes true,
* that CCID schedules the tasklet,
* tasklet function calls ccid_hc_tx_send_packet() via dccp_write_xmit(),
* since the wait-condition is now true, ccid_hc_tx_packet() returns "send now",
* packet is sent, and possibly more (since dccp_write_xmit() loops).
Code reuse: the taskled function calls dccp_write_xmit(), the timer function
reduces to a wrapper around the same code.
If the tasklet finds that the socket is locked, it re-schedules the tasklet
function (not the tasklet) after one jiffy.
Changed DCCP_BUG to dccp_pr_debug when transmit_skb returns an error (e.g. when a
local qdisc is used, NET_XMIT_DROP=1 can be returned for many packets).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The problem with Ack Vectors is that
i) their length is variable and can in principle grow quite large,
ii) it is hard to predict exactly how large they will be.
Due to the second point it seems not a good idea to reduce the MPS; in
particular when on average there is enough room for the Ack Vector and an
increase in length is momentarily due to some burst loss, after which the
Ack Vector returns to its normal/average length.
The solution taken by this patch is to subtract a minimum-expected Ack Vector
length from the MPS (previous patch), and to defer any larger Ack Vectors onto
a separate Sync - but only if indeed there is no space left on the skb.
This patch provides the infrastructure to schedule Sync-packets for transporting
(urgent) out-of-band data. Its signalling is quicker than scheduling an Ack, since
it does not need to wait for new application data.
It can thus serve other parts of the DCCP code as well.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
After moving the assignment of GAR/ISS from dccp_connect_init() to
dccp_transmit_skb(), the former function becomes very small, so that
a merger with dccp_connect() suggests itself.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This removes the argument `more' from ccid_hc_tx_packet_sent, since it was
nowhere used in the entire code.
(Anecdotally, this argument was not even used in the original KAME code where
the function originally came from; compare the variable moreToSend in the
freebsd61-dccp-kame-28.08.2006.patch now maintained by Emmanuel Lochin.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
To increase robustness, it is necessary to resend Confirm feature-negotiation
options, even though the RFC does not mandate it. But feature negotiation
options can take (much) more room than the options on common DataAck packets.
Instead of reducing the MPS always for a case which only applies to the three
messages send during initial handshake, this patch devises a special case:
if the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
to carry the options, and the feature-negotiation list is then flushed.
This means that the server gets two Acks for one Response. If both Acks get
lost, it is probably better to restart the connection anyway and devising yet
another special-case does not seem worth the extra complexity.
The patch (over-)estimates the expected overhead to be 32*4 bytes -- commonly
seen values were 20-90 bytes for initial feature-negotiation options.
It uses sizeof(u32) to mean "aligned units of 4 bytes". For consistency,
another use of sizeof is modified.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The Maximum Packet Size (MPS) is of interest for applications which want
to transfer data, so it is only relevant to the data transfer phase of a
connection (unless one wants to send data on the DCCP-Request, but that is
not considered here).
The strategy chosen to deal with this requirement is to leave room for only
such options that may appear on data packets.
A special consideration applies to Ack Vectors: this is purely guesswork,
since these can have any length between 3 and 1020 bytes. The strategy
chosen here is to subtract a configurable minimum, the value of 16 bytes
(2 bytes for type/length plus 14 Ack Vector cells) has been found by
experimentatation. If people experience this as too much or too little,
this could later be turned into a Kconfig option.
There are currently no CCID-specific header options which may appear on data
packets, hence it is not necessary to define a corresponding CCID field.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds a hook to resolve features whose value depends on the choice of
CCID. It is done at the server since it can only be done after the CCID
values have been negotiated; i.e. the client will add its CCID preference
list on the Change options sent in the Request, which will be reconciled
with the local preference list of the server.
The concept is documented on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
implementation_notes.html#ccid_dependencies
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This provides a missing link in the code chain, as several features implicitly
depend and/or rely on the choice of CCID. Most notably, this is the Send Ack Vector
feature, but also Ack Ratio and Send Loss Event Rate (also taken care of).
For Send Ack Vector, the situation is as follows:
* since CCID2 mandates the use of Ack Vectors, there is no point in allowing
endpoints which use CCID2 to disable Ack Vector features such a connection;
* a peer with a TX CCID of CCID2 will always expect Ack Vectors, and a peer
with a RX CCID of CCID2 must always send Ack Vectors (RFC 4341, sec. 4);
* for all other CCIDs, the use of (Send) Ack Vector is optional and thus
negotiable. However, this implies that the code negotiating the use of Ack
Vectors also supports it (i.e. is able to supply and to either parse or
ignore received Ack Vectors). Since this is not the case (CCID-3 has no Ack
Vector support), the use of Ack Vectors is here disabled, with a comment
in the source code.
An analogous consideration arises for the Send Loss Event Rate feature,
since the CCID-3 implementation does not support the loss interval options
of RFC 4342. To make such use explicit, corresponding feature-negotiation
options are inserted which signal the use of the loss event rate option,
as it is used by the CCID3 code.
Lastly, the values of the Ack Ratio feature are matched to the choice of CCID.
The patch implements this as a function which is called after the user has
made all other registrations for changing default values of features.
The table is variable-length, the reserved (and hence for feature-negotiation
invalid, confirmed by considering section 19.4 of RFC 4340) feature number `0'
is used to mark the end of the table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
The AWL lower Ack validity window advances in proportion to GSS, the greatest
sequence number sent. Updating AWL other than at connection setup (in the
DCCP-Request sent by dccp_v{4,6}_connect()) was missing in the DCCP code.
This bug lead to syslog messages such as
"kernel: dccp_check_seqno: DCCP: Step 6 failed for DATAACK packet, [...]
P.ackno exists or LAWL(82947089) <= P.ackno(82948208)
<= S.AWH(82948728), sending SYNC..."
The difference between AWL/AWH here is 1639 packets, while the expected value
(the Sequence Window) would have been 100 (the default). A closer look showed
that LAWL = AWL = 82947089 equalled the ISS on the Response.
The patch now updates AWL with each increase of GSS.
Further changes:
----------------
The patch also enforces more stringent checks on the ISS sequence number:
* AWL is initialised to ISS at connection setup and remains at this value;
* AWH is then always set to GSS (via dccp_update_gss());
* so on the first Request: AWL = AWH = ISS,
and on the n-th Request: AWL = ISS, AWH = ISS + n.
As a consequence, only Response packets that refer to Requests sent by this
host will pass, all others are discarded. This is the intention and in effect
implements the initial adjustments for AWL as specified in RFC 4340, 7.5.1.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch allows the sender to distinguish original and retransmitted packets,
which is in particular needed for the retransmission of DCCP-Requests:
* the first Request uses ISS (generated in net/dccp/ip*.c), and sets GSS = ISS;
* all retransmitted Requests use GSS' = GSS + 1, so that the n-th retransmitted
Request has sequence number ISS + n (mod 48).
To add generic support, the patch reorganises existing code so that:
* icsk_retransmits == 0 for the original packet and
* icsk_retransmits = n > 0 for the n-th retransmitted packet
at the time dccp_transmit_skb() is called, via dccp_retransmit_skb().
Thanks to Wei Yongjun for pointing this problem out.
Further changes:
----------------
* removed the `skb' argument from dccp_retransmit_skb(), since sk_send_head
is used for all retransmissions (the exception is client-Acks in PARTOPEN
state, but these do not use sk_send_head);
* since sk_send_head always contains the original skb (via dccp_entail()),
skb_cloned() never evaluated to true and thus pskb_copy() was never used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch fixes the following sparse warnings:
* nested min(max()) expression:
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__x' shadows an earlier one
net/dccp/ccids/ccid3.c:91:21: warning: symbol '__y' shadows an earlier one
* Declaration of function prototypes in .c instead of .h file, resulting in
"should it be static?" warnings.
* Declared "struct dccpw" static (local to dccp_probe).
* Disabled dccp_delayed_ack() - not fully removed due to RFC 4340, 11.3
("Receivers SHOULD implement delayed acknowledgement timers ...").
* Used a different local variable name to avoid
net/dccp/ackvec.c:293:13: warning: symbol 'state' shadows an earlier one
net/dccp/ackvec.c:238:33: originally declared here
* Removed unused functions `dccp_ackvector_print' and `dccp_ackvec_print'.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
dev_queue_xmit() and the other IP output functions expect to get a skb
with clear or properly initialized skb->cb. Unlike TCP and UDP, the
dccp_skb_cb doesn't contain a struct inet_skb_parm at the beginning,
so the DCCP-specific data is interpreted by the IP output functions.
This can cause false negatives for the conditional POST_ROUTING hook
invocation, making the packet bypass the hook.
Add a inet_skb_parm/inet6_skb_parm union to the beginning of
dccp_skb_cb to avoid clashes. Also add a BUILD_BUG_ON to make
sure it fits in the cb.
[ Combined with patch from Gerrit Renker to remove two now unnecessary
memsets of IPCB(skb)->opt ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dccp_v(4|6)_ctl_socket with sock to unify a code with TCP/ICMP.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a CCMPS field for setting a CCID-specific upper bound on the application payload
size, as is defined in RFC 4340, section 14.
Only the TX CCID is considered in setting this limit, since the RX CCID generates comparatively
small (DCCP-Ack) feedback packets. The CCMPS field includes network and transport layer header
lengths. The only current CCMPS customer is CCID4 (via RFC 4828).
A wrapper is used to allow querying the CCMPS even at times where the CCID modules may not have
been fully negotiated yet.
In dccp_sync_mss() the variable `mss_now' has been renamed into `cur_mps', to reflect that we are
dealing with an MPS, but not an MSS.
Since the DCCP code closely follows the TCP code, the identifiers `dccp_sync_mss' and
`dccps_mss_cache' have been kept, as they have direct TCP counterparts.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a separate routine to insert options during the initial handshake.
The main purpose is to conduct feature negotiation, for the moment the only user
is the timestamp echo needed for the (CCID3) handshake RTT sample.
Padding of options has been put into a small separate routine, to be shared among
the two functions. This could also be used as a generic routine to finish inserting
options.
Also removed an `XXX' comment since its content was obvious.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a socket option and signalling support for the case where the server
holds timewait state on closing the connection, as described in RFC 4340, 8.3.
Since holding timewait state at the server is the non-usual case, it is enabled
via a socket option. Documentation for this socket option has been added.
The setsockopt statement has been made resilient against different possible cases
of expressing boolean `true' values using a suggestion by Ian McDonald.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing active close, RFC 4340, 8.3. requires to retransmit the
Close/CloseReq with a backoff-retransmit timer starting at intially 2 RTTs.
This patch shifts the existing code for active-close retransmit timer
into output.c, so that the retransmit timer is started when the first
Close/CloseReq is sent. Previously, the timer was started when, after
releasing the socket in dccp_close(), the actively-closing side had not yet
reached the CLOSED/TIMEWAIT state.
The patch further reduces the initial timeout from 3 seconds to the required
2 RTTs, where - in absence of a known RTT - the fallback value specified in
RFC 4340, 3.4 is used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a nasty bug: dccp_send_reset() is called by both DCCPv4 and DCCPv6, but uses
inet_sk_rebuild_header() in each case. This leads to unpredictable and weird behaviour:
under some conditions, DCCPv6 Resets were sent, in other not.
The fix is to use the AF-independent rebuild_header routine.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.
I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.
I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This performs a minor optimisation: when ccid_hc_tx_send_packet
returns a value greater zero, then the same call previously was done
again at the begin of the while loop in dccp_wait_for_ccid.
This patch exploits the available information and schedule-timeouts
directly instead.
Documentation also added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This factors code common to dccp_v{4,6}_ctl_send_reset into a separate function,
and adds support for filling in the Data 1 ... Data 3 fields from RFC 4340, 5.6.
It is useful to have this separate, since the following Reset codes will always
be generated from the control socket rather than via dccp_send_reset:
* Code 3, "No Connection", cf. 8.3.1;
* Code 4, "Packet Error" (identification for Data 1 added);
* Code 5, "Option Error" (identification for Data 1..3 added, will be used later);
* Code 6, "Mandatory Error" (same as Option Error);
* Code 7, "Connection Refused" (what on Earth is the difference to "No Connection"?);
* Code 8, "Bad Service Code";
* Code 9, "Too Busy";
* Code 10, "Bad Init Cookie" (not used).
Code 0 is not recommended by the RFC, the following codes would be used in
dccp_send_reset() instead, since they all relate to an established DCCP connection:
* Code 1, "Closed";
* Code 2, "Aborted";
* Code 11, "Aggression Penalty" (12.3).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
In this patch, duplicated code is removed for the case when a Reset packet is
sent from a connected socket. This code duplication is between dccp_make_reset
and dccp_transmit_skb, which already contained an (up to now entirely unused)
switch statement to fill in the reset code from the DCCP_SKB_CB.
The only thing that has been removed is the call to dst_clone(dst), since
the queue_xmit functions use sk_dst_cache anyway.
I wasn't sure which purpose inet_sk_rebuild_header served, so I left it in.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds a FIXME to signal that the function dccp_send_delayed_ack is nowhere
used in the entire DCCP/CCID code.
Using a delayed Ack timer is suggested in 11.3 of RFC 4340, but it has also
rather subtle implications for the Ack-Ratio-accounting.
CCID2 does not use this (maybe it should).
I think leaving the function in is good, in case someone wants to implement
this.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
The parameter `seq' of dccp_send_sync() is in fact an acknowledgement number
and not a sequence number - thus renamed by this patch into `ackno'.
Secondly, a `critical' warning is added when a Sync/SyncAck could not be sent.
Sanity: I have checked all other functions that are called in dccp_transmit_skb,
there are no clashes with the use of dccpd_ack_seq; no other function is
using this slot at the same time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds more detail in the wait_for_ccid packet scheduling loop.
In particular, it informs about (i) when delay is used and (ii) why
a packet is discarded.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX CCID needs the write_xmit_timer for delaying packet sends. Previously
this timer was only activated on active (connecting) sockets.
This patch initialises the write_xmit_timer in sync with the other timers, i.e.
the timer will be ready on any socket. This is used by applications with a
listening socket which start to stream after receiving an initiation by the
client. The write_xmit_timer is stopped when the application closes, as before.
Was tested to work and to remove the timer bug reported on dccp@vger.
Also moved timer initialisation into timer.c (static).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert 931731123a
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
That accumulated over the last months hackaton, shame on me for not
using git-apply whitespace helping hand, will do that from now on.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds a (debug) warning message which is triggered whenever a packet is
discarded due to send failure.
It also adds a conditional, so that an interruption during dccp_wait_for_ccid
is not treated as a `BUG': the rationale is that interruptions are external,
whereas bug warnings are concerned with the internals.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
It simplifies waiting for the CCID module to signal that a packet
is ready to be sent. Other simplifications flow on from this such as
removing constants.
As a result of this EAGAIN is not returned any more by dccp_wait_for_ccid
(which would otherwise lead to unnecessarily discarding the packet in
dccp_write_xmit).
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch implements a suggestion by Ian McDonald and
1) Avoids tests against negative packet lengths by using unsigned int
for packet payload lengths in the CCID send_packet()/packet_sent() routines
2) As a consequence, it removes an now unnecessary test with regard to `len > 0'
in ccid3_hc_tx_packet_sent: that condition is always true, since
* negative packet lengths are avoided
* ccid3_hc_tx_send_packet flags an error whenever the payload length is 0.
As a consequence, ccid3_hc_tx_packet_sent is never called as all errors
returned by ccid_hc_tx_send_packet are caught in dccp_write_xmit
3) Removes the third argument of ccid_hc_tx_send_packet (the `len' parameter),
since it is currently always set to skb->len. The code is updated with regard
to this parameter change.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does not change code; it performs some trivial clean/tidy-ups:
* removal of a `debug_prefix' string in favour of the
already existing dccp_role(sk)
* add documentation of structures and constants
* separated out the cases for invalid packets (step 1
of the packet validation)
* removing duplicate statements
* combining declaration & initialisation
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Throughout the TCP/DCCP (and tunnelling) code, it often happens that the
return code of a transmit function needs to be tested against NET_XMIT_CN
which is a value that does not indicate a strict error condition.
This patch uses a macro for these recurring situations which is consistent
with the already existing macro net_xmit_errno, saving on duplicated code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This
* resolves a FIXME - DCCPv6 connections started all with
an initial sequence number of 1;
* provides a redirection `secure_dccpv6_sequence_number'
in case the init_sequence_v6 code should be updated later;
* concentrates the update of S.GAR into dccp_connect_init();
* removes a duplicate dccp_update_gss() in ipv4.c;
* uses inet->dport instead of usin->sin_port, due to the
following assignment in dccp_v4_connect():
inet->dport = usin->sin_port;
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does the following:
a) introduces variable-length checksums as specified in [RFC 4340, sec. 9.2]
b) provides necessary socket options and documentation as to how to use them
c) basic support and infrastructure for the Minimum Checksum Coverage feature
[RFC 4340, sec. 9.2.1]: acceptability tests, user notification and user
interface
In addition, it
(1) fixes two bugs in the DCCPv4 checksum computation:
* pseudo-header used checksum_len instead of skb->len
* incorrect checksum coverage calculation based on dccph_x
(2) removes dccp_v4_verify_checksum() since it reduplicates code of the
checksum computation; code calling this function is updated accordingly.
(3) now uses skb_checksum(), which is safer than checksum_partial() if the
sk_buff has is a non-linear buffer (has pages attached to it).
(4) fixes an outstanding TODO item:
* If P.CsCov is too large for the packet size, drop packet and return.
The code has been tested with applications, the latest version of tcpdump now
comes with support for partial DCCP checksums.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch fixes data being spewed into the logs continually. As the
code stood if there was a large queue and long delays timeo would go
down to zero and never get reset.
This fixes it by resetting timeo. Put constant into header as well.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is a code simplification:
it combines three often recurring operations into one inline function,
* allocate `len' bytes header space in skb
* fill these `len' bytes with zeroes
* cast the start of this header space as dccp_hdr
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The data itself is already charged to the SKB, doing
the skb_set_owner_w() just generates a lot of noise and
extra atomics we don't really need.
Lmbench improvements on lat_tcp are minimal:
before:
TCP latency using localhost: 23.2701 microseconds
TCP latency using localhost: 23.1994 microseconds
TCP latency using localhost: 23.2257 microseconds
after:
TCP latency using localhost: 22.8380 microseconds
TCP latency using localhost: 22.9465 microseconds
TCP latency using localhost: 22.8462 microseconds
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds transmit buffering to DCCP.
I have tested with CCID2/3 and with loss and rate limiting.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
And not the silly LIMIT_NETDEBUG and silently return without inserting
the option requested.
Also drop some old debugging messages associated to option insertion.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using this also provides opportunities for introducing
inet_csk_alloc_skb that would call alloc_skb, account it to the sock
and skb_reserve(max_header), but I'll leave this for later, for now
using sk_prot->max_header consistently is enough.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
