This will be used in a later patch to make the pin quirk table shorter.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec. Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Reported-and-tested-by: Dana Goyette <danagoyette@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 3830TG with CX20588 codec has a digital built-in mic that
has the same problem like many others, the inverted signal in stereo.
Apply the same fixup to this machine, too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire V5 doesn't set up the pins correctly at the cold boot
while the pins are corrected after the warm reboot. This patch gives
the proper pin configs statically in the driver as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81561
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both Haswell and Broadwell need set depop_delay to 0. So apply this
setting to haswell plus.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are many codes doing writes or updates COEF verbs sequentially
in a batch. Rewrite such open codes with tables for optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The helper functions snd_hda_check_board_config() and
snd_hda_check_board_codec_sid_config() are no longer used since the
transition to the generic parser and all quirks have been replaced
with fixups. Let's kill these dead codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some HP laptops, the mute led is controlled by codec gpio.
When some machine resume from s3/s4, the codec gpio data will be
cleared to 0 by BIOS:
Before suspend:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
After resume:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=0, unsol=0
To skip the AFG node to enter D3 can't fix this problem.
A workaround is to restore the gpio data when the system resume
back from s3/s4. It is safe even on the machines without this
problem.
BugLink: https://bugs.launchpad.net/bugs/1358116
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 & co have many vendor-specific setups with COEF verbs.
However, some verbs seem specific to some codec versions and they
result in the codec stalling. Typically, such a case can be avoided
by checking the return value from reading a COEF. If the return value
is -1, it implies that the COEF is invalid, thus it shouldn't be
written.
This patch adds the invalid COEF checks in appropriate places
accessing ALC269 and its variants. The patch actually fixes the
resume problem on Acer AO725 laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181
Tested-by: Francesco Muzio <muziofg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexnat HD-audio driver has a workaround for cx5051 (aka CX20561)
chip to add fake mute controls to each amp (commit 3868137e). This
implies the minimum-as-mute TLV bit in TLV for each corresponding
control. Meanwhile we build the virtual master from these, but the
TLV bit is missing, even though the slaves have it.
This patch simply adds the missing TLV_DB_SCALE_MUTE bit for vmaster,
as already done in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0132 driver tries to reload the firmware at resume. Usually this
works since the firmware loader core caches the firmware contents by
itself. However, if the driver failed to load the firmwares
(e.g. missing files), reloading the firmware at resume goes through
the actual file loading code path, and triggers a kernel WARNING like:
WARNING: CPU: 10 PID:11371 at drivers/base/firmware_class.c:1105 _request_firmware+0x9ab/0x9d0()
For avoiding this situation, this patch makes CA0132 skipping the f/w
loading at resume when it failed at probe time.
Reported-and-tested-by: Janek Kozicki <cosurgi@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If nid 0x15 (Headphone Playback Switch) is in D3 and headphones are
plugged in when the laptop reboots, a pop noise is generated.
Prevent this by keeping nid 0x15 in D0 when headphones are plugged in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the laptop is powered on with a jack plugged in, independently on what
is plugged, the jack is treated as a microphone jack.
Initialize the capture source so that by default jacks are treated as
headphones jacks. This will also prevent pop noises on boot in case
headphones are plugged in since setting/unsetting mic-in as input source
causes a pop noise.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMI8888 codec chip has a boost amp (only) on the headphone pin, and
this confuses the generic parser, which tends to pick up the most
outside amp. This results in the wrong volume setup, as the driver
complains like:
hda_codec: Mismatching dB step for vmaster slave (-100!=1000)
For avoiding this problem, rule out the amp on NID 0x10 and create
"Headphone Amp" volume control manually instead.
Note that this patch still doesn't fix all problems yet. The sound
output from the line out seems still too low. It will be fixed in
another patch (hopefully).
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Phoebus with CMI8888 HD-audio chip (PCI id 13f6:5011) doesn't
work with HD-audio driver as is because of some weird nature. For
making DMA properly working, we need to disable MSI. The position
report buffer doesn't work, thus we need to force reading LPIB
instead. And yet, the codec CORB/RIRB communication gives errors
unless we disable the snooping (caching).
In this patch, all these workarounds are added as a quirk for the
device. The HD-audio *codec* chip needs yet another workaround, but
it'll be provided in the succeeding patch.
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It will be recording voice delay for resume back recording for Headset Mic.
This alc286 will quickly open Headset Mic, to prevent avoid recording files are missing.
The issue was fixed. This is follow ALC286 programing guide.
[fix build error, add static and renamed the function by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862883) and module alias for Braswell
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Braswell platform.
It is an HDA Intel PCH controller.
AZX_DCAPS_ALIGN_BUFSIZE is not necessary for this controller.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mic mute led on dell laptops is controlled by the wmi driver.
Followed this part being merged to the kernel, we add the mic mute led
hook in the hda driver.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ON the machine, two pin complex (0xb and 0xe) are both routed to
the same external right-side mic jack, this makes the jack can't work.
To fix this problem, set the 0xe to "not connected".
BugLink: https://bugs.launchpad.net/bugs/1350148
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell XPS 15 (1028:05fe) gives the bad feedback noise from analog
loopback line even if the channels are muted. The similar problem has
been seen on XPS 13, and it was fixed by simply disabling loopback.
The same fixup was confirmed to be applicable and fix the problem on
XPS 15, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80821
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new quirk table to make sure that pin quirks have a higher
priority than quirks that apply to an entire vendor.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, calling one quirk function first and another later
would make the latter one take priority, this is now changed
to make the former take priority.
By adding two special values for fixup_id we can also get rid of the
fixup_forced flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Gigabyte BRIX BXBT-2707 is a mini-PC with Realtek ALC283 HDA,
exposing a single headset jack.
However, the default pin config information only suggests
that one pin is connected: a HP out jack (pin 0x21, default
config 0x04211010).
The microphone input is behind pin 0x19, which has default
config 0x411111f0 (i.e. unused), so it does not show up in
userspace, and no microphone input is possible via the headset.
Override the pin config so that the headset mic can be used.
[rearranged the fixup entry position by tiwai]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the mute LED work on a HP 15 touchsmart machine.
BugLink: https://bugs.launchpad.net/bugs/1334950
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since init_failed flag was moved to struct hda_intel, its access in
the commit [4da63c6f: ALSA: hda - Fix broken PM due to incomplete
i915 initialization] is also replaced with hda->init_failed
appropriately.
When the initialization of Intel HDMI controller fails due to missing
i915 kernel symbols (e.g. HD-audio is built in while i915 is module),
the driver discontinues the probe. However, since the probe was done
asynchronously, the driver object still remains, thus the relevant PM
ops are still called at suspend/resume. This results in the bad access
to the incomplete audio card object, eventually leads to Oops or stall
at PM.
This patch adds the missing checks of chip->init_failed flag at each
PM callback in order to fix the problem above.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79561
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We got a regression report for 3.15.x kernels, and this turned out to
be triggered by the fix for stream assignment order. On reporter's
machine with Intel controller (8086:1e20) + VIA VT1802 codec, the
first playback slot can't work with speaker outputs.
But the original commit was actually a fix for AMD controllers where
no proper GCAP value is returned, we shouldn't revert the whole
commit. Instead, in this patch, a new flag is introduced to determine
the stream assignment order, and follow the old behavior for Intel
controllers.
Fixes: dcb32ecd9a ('ALSA: hda - Do not assign streams in reverse order')
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the led_power_filter() needs to handle 3 situations:
- only mute_led_nid is set
- only cap_mute_led_nid is set
- both mute_led_ind and cap_mute_led_nid are set
BugLink: https://bugs.launchpad.net/bugs/1329580
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0070 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda_tegra_disable_clocks() function is only used by the suspend and
resume code, so it needs to be included in the #ifdef CONFIG_PM_SLEEP
block to prevent the following warning:
CC sound/pci/hda/hda_tegra.o
sound/pci/hda/hda_tegra.c:238:13: warning: 'hda_tegra_disable_clocks' defined but not used [-Wunused-function]
static void hda_tegra_disable_clocks(struct hda_tegra *data)
^
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
print_nid_path has a possible buffer overflow if
struct nid_path.path values are > 256.
Avoid this and neaten the output to remove the leading ':'
Neaten debug_badness to always verify arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'status' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Tested-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "list" field has been omitted from struct azx, but its
initialization remained mistakenly in hda_tegra.c, which leads to a
compile error:
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_create':
sound/pci/hda/hda_tegra.c:481:22: error: 'struct azx' has no member
named 'list'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 9a34af4a33 ('ALSA: hda - Move more PCI-controller-specific stuff from generic code')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit [6194b99d: ALSA: hda - Kill the rest of snd_print*()
usages] changed the callback map_slaves(), but one call was forgotten
to be replaced due to the cast, which leads to kernel Oops due to
invalid function. This patch replaces it with a proper function.
Fixes: 6194b99de9 ('ALSA: hda - Kill the rest of snd_print*() usages')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The similar fixup as T440 is needed for supporting the dock on T540.
Reported-by: Jim Minter <jminter@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another quirk to make the headset mic work on some new Dell machines.
Cc: Hui Wang <hui.wang@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1297581
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_ prefix doesn't mean that it's specific to ICH6 chipset but
rather its generic for all HD-audio (or "Azalia") devices.
Use AZX_ prefix instead to align with other constants.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just move struct fields between struct azx and struct hda_intel, and
move some definitions from hda_priv.h to hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and move most parts into hda_intel.c from the generic controller
code. This is a clean up, and there should be no functional change by
this patch.
Now, struct azx obtains the generic callbacks for getting the position
and the delay. As default NULL, posbuf is read. These replace the
old position_fix[], and each is implemented as a callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell/Broadwell display HD-A controller, the 24MHz HD-A link BCLK
is converted from Core Display Clock (CDCLK): BCLK = CDCLK * M / N
And there are two registers EM4 and EM5 to program M, N value respectively.
The EM4/EM5 values will be lost and when the display power well is disabled.
BIOS programs CDCLK selected by OEM and EM4/EM5, but BIOS has no idea about
display power well on/off at runtime. So the M/N can be wrong if non-default
CDCLK is used when the audio controller resumes, which results in an invalid
BCLK and abnormal audio playback rate. So this patch saves and restores valid
M/N values on controller suspend/resume.
And 'struct hda_intel' is defined to contain standard HD-A 'struct azx' and
Intel specific fields, as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Spectre 13 has the IDT 92HD95 codec, and BIOS seems to set the
default high-pass filter in some "safer" range, which results in the
very soft tone from the built-in speakers in contrast to Windows.
Also, the mute LED control is missing, since 92HD95 codec still has no
HP-specific fixups for GPIO setups.
This patch adds these missing features: the HPF is adjusted by the
vendor-specific verb, and the LED is set up from a DMI string (but
with the default polarity = 0 assumption due to the incomplete BIOS on
the given machine).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74841
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The static quirk code has been disabled for a while and it seems
working fine, so it's time to actually get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The static quirk code has been disabled for a while and it seems
working fine, so it's time to actually get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass the codec object so that we can replace all the rest of
snd_print*() usages with the proper device-specific print helpers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is cosmetical - it makes the pin quirk table look better.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is cosmetical - it makes the new pin quirk table look better.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two bug reporters with Dell XPS 15 report that they need to use the
dell-headset-multi model to get the headset mic working.
The two bug reporters have different PCI SSID (1028:05fd and 1028:05fe)
but this pin quirk matches both.
BugLink: https://bugs.launchpad.net/bugs/1331915
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to call the proper init function in case it has been
overridden, as it might restore things that the generic routing
doesn't know anything about. E.g. AMD cards have special verbs
that need resetting.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=77901
Fixes: 5a61358433 ('ALSA: hda - hdmi: Add ATI/AMD multi-channel audio support')
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Cc: <stable@vger.kernel.org> [v3.13+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A recent refactoring broke the possibility to manually specify
model name as a module parameter. This patch restores the desired
functionality.
Fixes: c21c8cf77f ('ALSA: hda - Add fixup_forced flag')
Reported-by: Kent Baxley <kent.baxley@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP mute led support output mute led and input mute led.
ALC280:
GPIO3 to control output mute led.
Mic1 vref to control input mute led.
ALC282:
Line1 vref to control output mute led.
Mic1 vref to control input mute led.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a machine is booted with nomodeset option, i915 driver skips the
whole initialization. Meanwhile, HD-audio tries to bind wth i915 just
by request_symbol() without knowing that the initialization was
skipped, and eventually it hits WARN_ON() in i915_request_power_well()
and i915_release_power_well() wrongly but still continues probing,
even though it doesn't work at all.
In this patch, both functions are changed to return an error in case
of uninitialized state instead of WARN_ON(), so that HD-audio driver
can give up HDMI controller initialization at the right time.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> [3.15]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More HP machine need mute led support.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fixup value for codec alc293 was set to
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE by a mistake, if we don't fix it,
the Dock mic will be overwriten by the headset mic, this will make
the Dock mic can't work.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will verify the pin's coverter selection for an active stream
when an unsol event reports this pin becomes available again after a display
mode change or hot-plug event.
For Haswell+ and Valleyview: display mode change or hot-plug can change the
transcoder:port connection and make all the involved audio pins share the 1st
converter. So the stream using 1st convertor will flow to multiple pins
but active streams using other converters will fail. This workaround
is to assure the pin selects the right conveter and an assigned converter is
not shared by other unused pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bios does not set up the pin config default correctly (everything
is set to zero). Reporter claims that 6stack-dig and 6stack-automute
solve the problem.
Alsa-info at http://www.alsa-project.org/db/?f=376c0804cbdde90bcd2cb94799407cb1cacf5d05
BugLink: https://bugs.launchpad.net/bugs/1319291
Reported-by: Stefano Statuti <stefano.statuti@hotmail.it>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7189eb9b8f.
It will use LPIB to get the DMA position on Broadwell HDMI Audio.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell HDMI can't use position buffer reliably, force to use LPIB
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These two new pin tables can fix headset mic problems for several
new Dell machines.
And also delete some machines from old quirk table since the existing
pin talbes already cover them.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New codec support for ALC891.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion to a fixup table for Replacer model with ALC260 in
commit 20f7d928 took the wrong widget NID for COEF setups. Namely,
NID 0x1a should have been used instead of NID 0x20, which is the
common node for all Realtek codecs but ALC260.
Fixes: 20f7d928fa ('ALSA: hda/realtek - Replace ALC260 model=replacer with the auto-parser')
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correcion of wrong fixup entries add in commit ca8f0424 to replace
static model quirk for PB V7900 laptop (will model).
[note: the removal of ALC260_FIXUP_HP_PIN_0F chain is also needed as a
part of the fix; otherwise the pin is set up wrongly as a headphone,
and user-space (PulseAudio) may be wrongly trying to detect the jack
state -- tiwai]
Fixes: ca8f04247e ('ALSA: hda/realtek - Add the fixup codes for ALC260 model=will')
Signed-off-by: Ronan Marquet <ronan.marquet@orange.fr>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS A8JN with AD1986A codec seems following the normal EAPD in the
normal order (0 = off, 1 = on) unlike other machines with AD1986A.
Apply the workaround used for Toshiba laptop that showed the same
problem.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75041
Cc: <stable@vger.kernel.org> [3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit c687200b9d.
Dropping the def association and sequence from pinconf comparing is a
bit risky, It will introduce a greater risk of catching unwanted
machines.
And in addition, so far no BIOS experts give us an explicit answer
whether it makes senses to compare these two fields or not.
For safety reason, we revert this commit.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_PM is disabled, the CONFIG_SND_HDA_POWER_SAVE_DEFAULT symbol
does not get defined, which causes a build error for the hda-tegra driver:
hda/hda_tegra.c:80:25: error: 'CONFIG_SND_HDA_POWER_SAVE_DEFAULT' undeclared here (not in a function)
static int power_save = CONFIG_SND_HDA_POWER_SAVE_DEFAULT;
^
/git/arm-soc/sound/pci/hda/hda_tegra.c:235:13: warning: 'hda_tegra_disable_clocks' defined but not used [-Wunused-function]
static void hda_tegra_disable_clocks(struct hda_tegra *data)
^
This works around the problem by not referencing that macro
when CONFIG_PM is disabled. Instead, we assume that it's disabled
unconditionally and cannot be enabled at runtime.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Dylan Reid <dgreid@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When headphones are plugged in, force AFG and node 0x02
("Headphone Playback Volume") to D0 to avoid pop noises.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just two members in the alc269_pin_fixup_tbl[] can cover more than
10 Dell laptop models.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A lot a machine have the same codec, but they have different default
pinconf setting just because the def association and sequence is
different, as a result they can't share a hda_pintbl[], to overcome
it, we don't compare def association and sequence in the pinconf
matching.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Normally, we match on pci ssid only. This works but needs new code
for every machine. To catch more machines in the same quirk, let's add
a new type of quirk, where we match on
1) PCI Subvendor ID (i e, not device, just vendor)
2) Codec ID
3) Pin configuration default
If all these three match, we could be reasonably certain that the
quirk should apply to the machine even though it might not be the
exact same device.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "fixup_forced" flag will indicate whether a specific fixup
(or nofixup) has been set by the user, to override the driver's
default.
This flag will help future patches.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent Intel H97/Z97 chipsets need the similar setups like other
Intel chipsets for snooping, etc. Especially without snooping, the
audio playback stutters or gets corrupted. This fix patch just adds
the corresponding PCI ID entry with the proper flags.
Reported-and-tested-by: Arthur Borsboom <arthurborsboom@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We should prefer `const struct pci_device_id` over
`DEFINE_PCI_DEVICE_TABLE` to meet kernel coding style guidelines.
This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
It has been tested by compilation.
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The analog-loopback causes the speaker noises even if it's set to zero
volume. As a simple workaround, just get rid of the loopback mixer.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=873704
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disable the AA-loopback path to get rid of the constant white noise
that can be heard when headphones are used.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I missed a rename during the review process. Fix the
MODULE_DEVICE_TABLE to match the structure.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a driver for the HDA block in Tegra SoCs. The HDA bus is
used to communicate with the HDMI codec on Tegra124.
Most of the code is re-used from the Intel/PCI HDA driver. It brings
over only two of the module params, power_save and probe_mask.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell display controller has 3 stream DMA engines. DMA0 cannot update DMA
postion buffer properly while DMA1 and DMA2 can work well. So this patch masks
the buggy DMA0 by keeping it as opened.
This is a tentative workaround, so keep the change small as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0071 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x1028065c; VID: 0x10ec0255, SID: 0x10280680; VID: 0x10ec0292,
SID: 0x10280684), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
And on the machine with SID 0x10280684, and the Lineout and external
microphone should be routed to docking, this patch also fix this
problem.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone and mic jacks on Thinkpad T440 are assigned to pins NID
0x16 and 0x19, respectively. These need to be set up manually by a
fixup.
Reported-and-tested-by: Joschi Brauchle <joschi.brauchle@tum.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently infoframe contents and channel mapping are only set when a
sink (monitor) is present.
However, this does not make much sense, since
1) We can make a very reasonable guess on CA after 18e391862c ("ALSA:
hda - hdmi: Fallback to ALSA allocation when selecting CA") or by
relying on a previously valid ELD (or we may be using a
user-specified channel map).
2) Not setting infoframe contents and channel count simply means they
are left at a possibly incorrect state - playback is still allowed
to proceed (with missing or wrongly mapped channels).
Reasons for monitor_present being 0 include disconnected cable, video
driver issues, or codec not being spec-compliant. Note that in
actual disconnected-cable case it should not matter if these settings
are wrong as they will be re-set after jack detection, though.
Change the behavior to allow the infoframe contents and the channel
mapping to be set even without a sink/monitor, either based on the
previous valid ELD contents, if any, or based on sensible defaults
(standard channel layouts or provided custom map, sink type HDMI).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Stephan Raue <stephan@openelec.tv>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Stephan Raue <stephan@openelec.tv>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x1028067e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit (ca460f8652) changed the CORB RP reset procedure to
follow the specification with a couple of sanity checks.
Unfortunately, Nvidia controller chips seem not following this way,
and spew the warning messages like:
snd_hda_intel 0000:00:10.1: CORB reset timeout#1, CORBRP = 0
This patch adds the workaround for such chips. It just skips the new
reset procedure for the known broken chips.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New codec ALC293/ALC3235 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x10280674), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x1028067f), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The full_reset argument to azx_init_chip() carries boolean rather than
numerical information, so update the type to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0283,
SID: 0x10280667), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From azx_interrupt, use the helper to check if the device is active
instead of checking the state. This will do the right thing if
runtime pm is disabled in addition to if the device is suspended.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently stream numbers are assigned in reverse order.
Unfortunately commit 7546abfb8e ("ALSA: hda - Increment
default stream numbers for AMD HDMI controllers") assumed this was not
the case (specifically, it had the "old cards had single device only"
=> "extra unused stream numbers do not matter" assumption), causing
non-working audio regressions for AMD Radeon HDMI users.
Change the stream numbers to be assigned in forward order.
The benefit is that regular audio playback will still work even if the
assumed stream count is too high, downside is that a too high stream
count may remain hidden.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77002
Reported-by: Christian Güdel <cg@dmesg.ch>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Christian Güdel <cg@dmesg.ch> # 3.14
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add eapd shutup function to alc283_shutup.
It could avoid pop noise from speaker.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chrome OS was use model name of alc283-dac-wcaps for loading model as default.
Change the model name to same as model name of Chrome OS for future support.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is better to change Mic2-Vref to manual mode.
Manual control Mic2-Vref will solve pop noise issue.
It will improve pop noise for power on, power off, S3 and resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fixups for HP laptops to support the mute LED made the
speaker output silent on some machines. It turned out that they use
the NID 0x18 for the speaker while it's also used for controlling the
LED via VREF bits although the current driver code blindly assumes
that such a node is a mic pin (where 0x18 is usually so).
This patch fixes the problem by only changing the VREF bits and
keeping the other pin ctl bits.
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If it only has single output of HP out of machine.
The driver parser will copy hp_pins to line_out_pins.
hp_pins will empty for alc283_init and alc283_shutup functions.
This will cause not have value for hp_pin_sense.
Add check line_out_type code will solve it .
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The `lspci -nnvv` output contains (wrapped for line length):
00:1b.0 Audio device [0403]:
Intel Corporation 7 Series/C210 Series Chipset Family
High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:115d]
Signed-off-by: W. Trevor King <wking@tremily.us>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x10280632; VID: 0x10ec0293, SID: 0x1028062c; VID: 0x10ec0293,
SID: 0x1028062e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-parser may ignore some pins that could be valid when they
don't match with the assumption or if there are way too many pins
assigned to the same output type. So far, such a pin has been
silently ignored, but it's better to leave a message, which would help
for debugging and understanding the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a temporary fix for some Intel HDMI codecs to avoid no sound output for
a resuming playback after S3.
After S3, the audio driver restores pin:cvt connection selections by
snd_hda_codec_resume_cache(). However this can happen before the gfx side is
ready and such connect selection is overlooked by HW. After gfx is ready, the
pins make the default selection again. And this will cause multiple pins share
a same convertor and mute control will affect each other. Thus a resumed audio
playback become silent after S3.
This patch verifies pin:cvt connection on preparing a stream, to assure the pin
selects the right convetor and an assigned convertor is not shared by other
unused pins. Apply this fix-up on Haswell, Broadwell and Valleyview (Baytrail).
We need this temporary fix before a reliable software communication channel is
established between audio and gfx, to sync audio/gfx operations.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the power state of ALC283 codec goes to D3 or return back to D0,
it gives a noise via headphone output. To follow the depop procedure,
it will be better.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71861
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
This patch initialized the local audio InfoFrame variable 'ai' to be all zero,
thus the data bytes will indicate "Refer to Stream Header" by default.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo IdeaPad 410Y with ALC282 codec makes loud click noises at boot
and shutdown. Also, it wrongly misdetects the acpi_thinkpad hook.
This patch adds a device-specific fixup for disabling the shutup
callback that is the cause of the click noise and also avoiding the
thinpad_helper calls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71511
Reported-and-tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the driver behavior compatible with the earlier kernels,
use the analog beep in the loopback path instead of the digital beep.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer widget (NID 0x20) of AD1884 and AD1984 codecs isn't
connected directly to the actual I/O paths but only via another mixer
widget (NID 0x21). We need a similar fix as we did for AD1882.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When plugging a headphone or headset, lots of noise is heard from
internal speaker, after changing the automute via amp instead of
pinctl, the noise disappears.
BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ops to read and write registers should take pointers labeled as
__iomem. Thanks to the sparse bot for catching this.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using readl, writel, etc. resulted in some architectures, such as
s390, expanding the member names into zpci_writel. Obviously not the
intended result.
Fixes s390 build breakage introduced by "4083081 - ALSA: hda - Allow
different ops to read/write registers"
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the dependency on CONFIG_PCI for building hda codec drivers so
that platforms with HDA attach via means other than PCI can use them.
This was as suggested by tiwai.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codec creation and stream initialization can be shared between
hda_intel and hda platform drivers. Move it and the static functions
it depends on to hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code will be reused by an hda_platform driver as it has no PCI
dependencies. This allows update_rirb to be static as all users are
now in hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This op will be used by hda_intel to do the position check. Takashi
wisely suggested adding this before moving the interrupt handler to
common HDA code. Having this callback prevents the need to move the
hda_intel specific delayed interrupt handling with the irq.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Share more code from hda_intel. This moves the link control and
initialization to hda_controller. The code will also be used by an
hda platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Combining the call to alloc_cmd_io with the allocate pages function
removes an extra interface between hda_intel and hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is done to allow an HDA platform driver to reuse the code.
A few of the interfaces added to hda_controller will disappear in
following commits as their users are also moved to hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Moving the DSP loading functionality to hda_controller.c means that
the dsp lock doesn't need to be shared in hda_intel and
hda_controller. The forthcoming platform driver doesn't need the DSP
loading code, but sharing it doesn't hurt.
Tested on Chromebook Pixel's ca0132 that uses the DSP loader.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull allocation from first_init to a new function in hda_controller.c.
Short term this will allow the dsp loader to be moved as well. In
later commits it will allow the same allocation to be used by the
platform hda driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull the pcm_ops and the functions they use into a new hda_controller
file. This is done to allow for other hda implementations besides PCI
to use the same ops. The hda_controller file will house functionality
related to HDA but independent of the bus used to talk to the
controller.
This currently shares dsp locking across the two files. This will be
remedied in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding this op allows the X86 specific mmap operation to help in
hda_intel without needing a CONFIG_X86 in future non-PCI hda drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Break out the allocation of pages for DMA and PCM buffers to ops in
the chip structure. This is done to allow for architecture specific
work-arounds to be added. Currently mark_pages_wc is used by
hda_intel. This avoids needing to move that x86-specific code to a
common area shared with hda platform drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Passing the max slots and power save arguments to codec_create will
allow for its reuse by an hda_platform driver. It makes the function
independent of the module params in hda_intel and ready to move to
hda_shared in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keeping a pointer to the jackpoll_ms array in the chip will allow
azx_codec_create to be shared between hda_intel and hda_platform
drivers. Also modify get_jackpoll_ms to make the jackpoll_ms member
optional, this way a platform driver can leave it out if it's not
needed.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the code was updated last year the "#if 0" surrounding it
dates back to the original git commit. The function will be moved to
a new file, no need to carry the dead code.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a PCI-only feature, but adding a callback for it in the chip
structure breaks the PCI dependency in the RIRB code allowing the
logic there to be re-used by the platform HDA driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes calls to get the device via PCI from other parts of the
code that will be able to be re-used by the platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will allow for a platform hda driver to use it as well. It
removes the dependency on the module param from hda_intel, which will
allow for azx_setup_periods to be shared.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The forthcoming platform hda driver needs to override the way
registers are read and written. In preparation for that, introduce a
reg_ops struct that can be implemented differently by the new driver.
Change the existing macros to use the new structure, and move them to
hda_priv.h where they will be accessible to both PCI and platform
drivers.
Start with register access, but later commits will add more ops that
differ between PCI and platform.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Later commits adding support for hda platform drivers will want to use
the same defines and structures. Put them in a place reachable by both
hda_intel and the new platform driver.
This is a mostly a direct copy with a few whitespace and comment
changes to make checkpatch happy.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA spec, we must write 1 to bit 15 on a CORBRP
reset, read back 1, then write 0, then read back 0. This must be
done while the DMA is not running.
We accidentaly ended up writing back the 0 by using a writel
instead of a writew to CORBWP.
This caused occasional controller failure on Bay Trail hardware.
[replaced error messages with dev_err() by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep input device is registered via input_register_device(), but
this is called in snd_hda_attach_beep_device() where the sound devices
aren't registered yet. This leads to the binding to non-existing
object, thus results in failure. And, even if the binding worked
(against the PCI object), it's still racy; the input device appears
before the sound objects.
For fixing this, register the input device properly at dev_register
ops of the codec object it's bound with. Also, call
snd_hda_detach_beep_device() at dev_disconnection so that it's
detached at the right timing. As a bonus, since it's called in the
codec's ops, we can get rid of the further call from the other codec
drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many HP laptops with STAC codecs have a docking station port and BIOS
sets the pins for the input on the dock as a line in. Because the
generic parser doesn't handle a line in pin as auto-switchable, this
resulted in the manual capture source selection on these laptops.
However, from the usability POV, the automatic switching is easier.
This patch adds the line_in_auto_switch hint in the fixup function for
these laptops. Even if no dock port is present, this should be
harmless as the generic parser allows the auto-switching only in a
limited situation (all three pins are located in different
positions).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the controller, the new codec object is assigned as a
parent for the hd-audio beep input devices, just like already done for
PCM and hwdep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use dev_err() and co for messages from HD-audio controller and codec
drivers. The codec drivers are mostly bound with codec objects, so
some helper macros, codec_err(), codec_info(), etc, are provided.
They merely wrap the corresponding dev_xxx().
There are a few places still calling snd_printk() and its variants
as they are called without the codec or device context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some sysfs attributes like init_pin_configs or vendor_name are really
basic and should be available no matter whether the codec driver is
re-configurable or not. Put them out of #ifdef
CONFIG_SND_HDA_RECONFIG and allow the read-only accesses.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have currently sysfs attributes for each hwdep, but basically these
should belong to the codec itself, per se. Let's add them to the
codec object while keeping them for hwdep as is for compatibility.
While we are at it, split the sysfs-related stuff into a separate
source file, hda_sysfs.c, and keep only the stuff necessary for hwdep
in hda_hwdep.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the HD-audio is treated individually in each codec driver, it's
more convenient to assign an own struct device to each codec object.
Then we'll be able to use dev_err() more easily for each codec, for
example.
For achieving it, this patch just creates an object "hdaudioCxDy".
It belongs to sound class instead of creating a new bus, just for
simplicity, at this stage. No pm ops is implemented in the device
struct level but currently it's merely a container. The PCM and hwdep
devices are now children of this codec device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now each snd_hda_codec instance is managed via the device chain, the
registration and release are done by its callback instead of calling
from bus.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For referring to a different object from sysfs ops, take hwdep
private_data as stored via dev_set_drvdata() at creating the device
object. In that way, the same sysfs ops can be used by different
device types.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling each time device_create_file(), create the groups
of sysfs attribute files at once in a normal way. Add a new helper
function, snd_get_device(), to return the associated device object,
so that we can handle the sysfs addition locally.
Since the sysfs file addition is done differently now,
snd_add_device_sysfs_file() helper function is removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GPIO line used for the mute LED control on Lenovo Yxx0 laptops is
cleared unexpectedly when the codec goes to D3, typically by
power-saving. For avoiding it, add a power filter in the fixup.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Folio 13 may have a broken BIOS that doesn't set up the mute LED
GPIO properly, and the driver guesses it wrongly, too. Add a new
fixup entry for setting the GPIO pin statically for this laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70991
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The front headphone and mic jackes on a HP desktop model (Vendor Id:
0x111d76c7 Subsystem Id: 0x103c2b17) can not work, the codec on this
machine has 8 physical ports, 6 of them are routed to rear jackes
and all of them work very well, while the remaining 2 ports are
routed to front headphone and mic jackes, but the corresponding
pin complex node are not defined correctly.
After apply this fix, the front audio jackes can work very well.
[trivial fix of enum definition by tiwai]
BugLink: https://bugs.launchpad.net/bugs/1282369
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Gerald Yang <gerald.yang@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorrect ADC is picked in ca0132_capture_pcm_prepare(),
where it assumes multiple streams while there is one stream
per ADC. Note that ca0132_capture_pcm_cleanup() already does
the right thing.
The Chromebook Pixel has a microphone under the keyboard that
is attached to node id 0x8. Before this fix, recording would
always go to the main internal mic (node id 0x7).
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a HDMI stream is opened with the same stream tag
as a following opened stream to ca0132, audio will be
heard from two ports simultaneously.
Fix this issue by change to use snd_hda_codec_setup_stream
and snd_hda_codec_cleanup_stream instead, so that an
inactive stream can be marked as 'dirty' when found
with a conflict stream tag, and then get purified.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Reviewed-by: Chih-Chung Chang <chihchung@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machines (Vendor ID:
0x10ec0255, Subsystem ID: 0x10280657; Vendor ID: 0x10ec0255,
Subsystem ID: 0x1028065f), the headset mic can't be
detected, after apply this patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Realtek codec driver contains some codes referring to the PCI
subdevice IDs, but most of them are optional, typically for checking
the codec name variants. Add NULL checks appropriately so that it can
work without PCI assignment.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default parent device can be obtained directly via card object, so
we don't need to rely on pci->dev.parent. Since there is no access to
pci_dev, we can reduce the inclusion of linux/pci.h, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit d3c56568f4.
The reverted commit breaks audio through headphone line out on
the Acer TravelMate B113 (Type1Sku0) Notebook, my main work
machine. I don't know much about it but this fixes my problem.
Bisected and tested.
Fixes: d3c56568f4 ('ALSA: hda/realtek - Avoid invalid COEFs for ALC271X')
Cc: <stable@vger.kernel.org>
Tested-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last user of snd_hda_gen_spec_free() is patch_via.c, and we can
rewrite it safely with snd_hda_gen_free(), so that
snd_hda_gen_spec_free() can be a local function in hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to alsa-info.sh outputs, all three entries with static
quirks have the correct pin configs, so it's safe to remove static
quirks. For now, turn the static quirks off via ifdef. The dead
codes will be removed in later release.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even after the fix for leftover kconfig handling (commit f8f1becf),
the current code still doesn't handle properly the builtin/module
mixup case between the core snd-hda-codec and other codec drivers.
For example, when CONFIG_SND_HDA_INTEL=y and
CONFIG_SND_HDA_CODEC_HDMI=m, it'll end up with an unresolved symbol
snd_hda_parse_hdmi_codec. This patch fixes the issue.
Now codec->parser points to the parser object *only* when a module
(either generic or HDMI parser) is loaded and bound. When a builtin
symbol is used, codec->parser still points to NULL. This is the
difference from the previous versions.
Fixes: f8f1becfa4 ('ALSA: hda - Fix leftover ifdef checks after modularization')
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the lengthy #if defined(XXX) || defined(XXX_MODULE) with the
new IS_ENABLED() macro.
The patch still doesn't cover all ifdefs. For example, the dependency
on CONFIG_GAMEPORT is still open-coded because this also has an extra
dependency on MODULE. Similarly, an open-coded ifdef in pcm_oss.c and
some sequencer-related stuff are left untouched.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Bug reporter report that the -mode4 makes the subwoofer work.
I have simplified the quirk a bit to avoid possible regressions
with the microphones.
BugLink: https://bugs.launchpad.net/bugs/871808
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a small refactoring to make the next patch slightly simpler.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The very same fixup is needed to make the mic on Sony VAIO Pro 11
working as well as VAIO Pro 13 model.
Reported-and-tested-by: Hendrik-Jan Heins <hjheins@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code for controlling mic mute LED in patch_sigmatel.c
blindly assumes that there is a single capture switch. But, there can
be multiple multiple ones, and each of them flips the state, ended up
in an inconsistent state.
For fixing this problem, this patch adds kcontrol to be passed to the
hook function so that the callee can check which switch is being
accessed. In stac_capture_led_hook(), the state is checked as a
bitmask, and turns on the LED when all capture switches are off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the commit [595fe1b702: ALSA: hda - Make
CONFIG_SND_HDA_CODEC_* tristate], the kconfig variables for the
generic parser and codec drivers can be "m" instead of boolean, but
some codes are left unchanged to check only #ifdef
CONFIG_SND_HDA_CODEC_XXX, which is no longer true for modules.
This patch fixes them by replacing with IS_ENABLED() macros.
Fixes: 595fe1b702 ('ALSA: hda - Make CONFIG_SND_HDA_CODEC_* tristate')
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70161
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1983 has flexible loopback routes and the generic parser would take
wrong path confusingly instead of taking individual paths via NID 0x0c
and 0x0d. For avoiding it, limit the connections at these widgets so
that the parser can think more straightforwardly. This fixes the
regression of the missing line-in loopback on Dell machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70011
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mac Pro 1,1 with ALC889A codec needs the VREF setup on NID 0x18 to
VREF50, in order to make the speaker working. The same fixup was
already needed for MacBook Air 1,1, so we can reuse it.
Reported-by: Nicolai Beuermann <mail@nico-beuermann.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer widget on AD1983 at NID 0x0e was missing in the commit
[f2f8be43c5: ALSA: hda - Add aamix NID to AD codecs].
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70011
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've seen often problems after suspend/resume on Acer Aspire One
AO725 with ALC271X codec as reported in kernel bugzilla, and it turned
out that some COEFs doesn't work and triggers the codec communication
stall.
Since these magic COEF setups are specific to ALC269VB for some PLL
configurations, the machine works even without these manual
adjustment. So, let's simply avoid applying them for ALC271X.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite L40 with AD1986A codec requires the EAPD of NID 0x1b
to be constantly on, otherwise the output doesn't work.
Unlike most of other AD1986A machines, EAPD is correctly implemented
in HD-audio manner (that is, bit set = amp on), so we need to clear
the inv_eapd flag in the fixup, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67481
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Ideapad with ALC272 has a mute LED that is controlled via
GPIO1. Add a simple vmaster hook for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 384a48d715 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!
However, this apparently broke some Intel systems, and commit
6169b67361 "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.
This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.
Reported-by: Uosis <uosisl@gmail.com>
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While looking into some spurious responses, I found that the addr value was
treated a bit inconsistent: values 8..0xf will be treated as codec 0 and
values 0..7 will be treated as no error regardless of whether there is a codec
there, or not.
With this patch, all non-existing codecs will be treated equally.
In addition, printing rp and wp could help figuring out if the wp value is
reported wrongly from the controller or if something else is wrong.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now all weird setups have been converted to fixups for the generic
parser, and we can disable the static quirks. This commit just turns
the build off. The bulky static quirk code still remains for a while,
in case we get an overlooked regression. It'll be removed at the next
kernel version.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both CX20549 and CX20551 codecs have a mixer widget and it can be
connected as the ADC source. Like AD and VIA codecs, enable the
add_stereo_mix_input flag for these codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OLPC XO needs a few special handling. Now these are implemented as a
fixup to the generic parser.
Obviously, the DC BIAS mode had to be added manually. This is mainly
implemented in the mic_autoswitch hook, where the mic pins are
overwritten depending on the DC bias mode. This also required the
override of the mic boost control, since the mic boost is applied only
when the DC mode is disabled.
In addition, the mic pins must be set dynamically at recording time
because these also control the LED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... by using snd_Hda_codec_update_cache() instead of *_write_cache().
Since all path elements should have been updated by this function,
we are safe to assume that the cache contents are consistent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on the Dell machine (Vendor ID:
0x10ec0255, Subsystem ID: 0x1028064d), the headset mic can't be
detected, after apply this patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: Doro Wu <fan-cheng.wu@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Processing coefficients are often a vital part of the codec's configuration,
so dumping them can be important. However, because they are undocumented and
secret, we do not want to enable this for all codecs by default.
Therefore instead add this as a debugging parameter.
I have prepared for codecs that want to enable this by default by the extra
dump_coef bitfield, but unsure if we want to do that as long as the
(unlikely, but still) race remains.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly to other Apple products, MBA 1,1 needs a specific quirk.
Pin 0x18 must be set to VREF_50 to have sound output. This was no
longer done since commit 1a97b7f, resulting in a mute built-in speaker.
This patch corrects the regression by creating a fixup for the MBA 1,1.
Fixes: 1a97b7f227 ("ALSA: hda/realtek - Remove the last static quirks for ALC882")
Cc: <stable@vger.kernel.org> [v3.4+]
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Zenbook UX31A has yet another problem -- softer output level than
others. According to the measurement, the peak output difference
between 31A and 31E is 5dB. As ALC269VB has a COEF for the class-D
pre-amp, let's apply it for +5dB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we plug a 3-ring headset on some Dell machines, the headset
mic can't be detected, after apply this patch, the headset mic
can work well on all those machines.
On the machine with the Subsytem ID 0x10280610, if we use
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE, the headset mic can be
detected and work well, but the sound can't be outputed via
headphone anymore, use ALC269_FIXUP_DELL3_MIC_NO_PRESENCE
can fix this problem.
BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: David Chen <david.chen@canonical.com>
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Tested-by: Shawn Wang <shawn.wang@canonical.com>
Tested-by: Chih-Hsyuan Ho <chih.ho@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new vmaster hook, update_tpacpi_mute_led(), calls the original
vmaster hook, but I forgot to save the original hook function but keep
calling the updated one, which of course results in a stupid endless
loop. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some AIO (All In One) models with the codec alc668
(Vendor ID: 0x10ec0668) on it, when we plug a headphone into the jack,
the system will switch the output to headphone and set the speaker to
automute as well as change the speaker Pin-ctls from 0x40 to 0x00,
this will bring loud noise to the headphone.
I tried to disable the corresponding EAPD, but it did not help to
eliminate the noise.
According to Takashi's suggestion, we use amp operation to replace the
pinctl modification for the automute, this really eliminate the noise.
BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apply the codec->power_filter to the FG nodes in general for reducing
hackish set_power_state ops override in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A). This patch removes the indep_hp flag for such codecs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the device ID for Intel Broadwell display HD-Audio controller,
and applies Haswell properties to this device.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
