MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
Second set of fixes for v5.12. Only three iwlwifi fixes this time, the
crash with MVM being the most important one and reported by multiple
people.
iwlwifi
* fix kernel crash regression when using LTO with MVM devices
* fix printk format warnings
* fix potential deadlock found by lockdep
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
First set of fixes for v5.12. One iwlwifi kernel crash fix and smaller
fixes to multiple drivers.
ath9k
* fix Spatial Multiplexing Power Save (SMPS) handling to improve thoughtput
mt76
* error handling fixes
* memory leax fixes
iwlwifi
* don't crash during debug collection on DVM devices
MAINTAINERS
* email address update
ath11k
* fix GCC warning about DMA address debug messages
* fix regression which broke QCA6390 AP mode
* tag 'wireless-drivers-2021-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: mt7915: fix unused 'mode' variable
mt76: dma: do not report truncated frames to mac80211
mt76: mt7921: remove incorrect error handling
iwlwifi: pcie: fix iwl_so_trans_cfg link error when CONFIG_IWLMVM is disabled
ath11k: fix AP mode for QCA6390
ath11k: qmi: use %pad to format dma_addr_t
MAINTAINERS: update for mwifiex driver maintainers
iwlwifi: avoid crash on unsupported debug collection
mt76: mt7915: only modify tx buffer list after allocating tx token id
mt76: fix tx skb error handling in mt76_dma_tx_queue_skb
ath9k: fix transmitting to stations in dynamic SMPS mode
====================
Link: https://lore.kernel.org/r/20210226164411.CDD03C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
clang points out a possible corner case in the mt7915_tm_set_tx_cont()
function if called with invalid arguments:
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:593:2: warning: variable 'mode' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:597:13: note: uninitialized use occurs here
rateval = mode << 6 | rate_idx;
^~~~
drivers/net/wireless/mediatek/mt76/mt7915/testmode.c:506:37: note: initialize the variable 'mode' to silence this warning
u8 rate_idx = td->tx_rate_idx, mode;
^
Change it to return an error instead of continuing with invalid data
here.
Fixes: 3f0caa3cbf ("mt76: mt7915: add support for continuous tx in testmode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b102f0c522 ("mt76: fix array overflow on receiving too many
fragments for a packet") fixes a possible OOB access but it introduces a
memory leak since the pending frame is not released to page_frag_cache
if the frag array of skb_shared_info is full. Commit 93a1d4791c
("mt76: dma: fix a possible memory leak in mt76_add_fragment()") fixes
the issue but does not free the truncated skb that is forwarded to
mac80211 layer. Fix the leftover issue discarding even truncated skbs.
Fixes: 93a1d4791c ("mt76: dma: fix a possible memory leak in mt76_add_fragment()")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/a03166fcc8214644333c68674a781836e0f57576.1612697217.git.lorenzo@kernel.org
Clang points out a mistake in the error handling in
mt7921_mcu_tx_rate_report(), which tries to dereference a pointer that
cannot be initialized because of the error that is being handled:
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:409:3: warning: variable 'stats' is uninitialized when used here [-Wuninitialized]
stats->tx_rate = rate;
^~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:401:32: note: initialize the variable 'stats' to silence this warning
struct mt7921_sta_stats *stats;
^
Just remove the obviously incorrect line.
Fixes: 1c099ab447 ("mt76: mt7921: add MCU support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225145953.404859-2-arnd@kernel.org
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
Commit c134d1f8c4 ("ath11k: Handle errors if peer creation fails") completely
broke AP mode on QCA6390:
kernel: [ 151.230734] ath11k_pci 0000:06:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant[2307]: Failed to set beacon parameters
wpa_supplicant[2307]: Interface initialization failed
wpa_supplicant[2307]: wlan0: interface state UNINITIALIZED->DISABLED
wpa_supplicant[2307]: wlan0: AP-DISABLED
wpa_supplicant[2307]: wlan0: Unable to setup interface.
wpa_supplicant[2307]: Failed to initialize AP interface
This was because commit c134d1f8c4 ("ath11k: Handle errors if peer creation
fails") added error handling for ath11k_peer_create(), which had been failing
all along but was unnoticed due to the missing error handling. The actual bug
was introduced already in commit aa44b2f3ec ("ath11k: start vdev if a bss peer is
already created").
ath11k_peer_create() was failing because for AP mode the peer is created
already earlier op_add_interface() and we should skip creation here, but the
check for modes was wrong. Fixing that makes AP mode work again.
This shouldn't affect IPQ8074 nor QCN9074 as they have hw_params.vdev_start_delay disabled.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: c134d1f8c4 ("ath11k: Handle errors if peer creation fails")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614006849-25764-1-git-send-email-kvalo@codeaurora.org
If CONFIG_ARCH_DMA_ADDR_T_64BIT=n:
drivers/net/wireless/ath/ath11k/qmi.c: In function ‘ath11k_qmi_respond_fw_mem_request’:
drivers/net/wireless/ath/ath11k/qmi.c:1690:8: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘dma_addr_t’ {aka ‘unsigned int’} [-Wformat=]
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1691 | ab->qmi.target_mem[i].paddr,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| dma_addr_t {aka unsigned int}
drivers/net/wireless/ath/ath11k/debug.h:64:30: note: in definition of macro ‘ath11k_dbg’
64 | __ath11k_dbg(ar, dbg_mask, fmt, ##__VA_ARGS__); \
| ^~~
drivers/net/wireless/ath/ath11k/qmi.c:1690:34: note: format string is defined here
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ~~~^
| |
| long long unsigned int
| %x
Fixes: d5395a5486 ("ath11k: qmi: add debug message for allocated memory segment addresses and sizes")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210221182754.2071863-1-geert@linux-m68k.org
When running out of room in the tx queue after calling drv->tx_prepare_skb,
the buffer list will already have been modified on MT7615 and newer drivers.
This can leak a DMA mapping and will show up as swiotlb allocation failures
on x86.
Fix this by moving the queue length check further up. This is less accurate,
since it can overestimate the needed room in the queue on MT7615 and newer,
but the difference is small enough to not matter in practice.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210216135119.23809-1-nbd@nbd.name
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Cc: stable@vger.kernel.org
Reported-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210214184911.96702-1-nbd@nbd.name
The documentation for the PHY update [1] states:
Loop 4 times with index i
If PHY Revision >= 3
Copy table[i] to coef[i]
Otherwise
Set coef[i] to 0
the copy of the table to coef is currently implemented the wrong way
around, table is being updated from uninitialized values in coeff.
Fix this by swapping the assignment around.
[1] https://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal/
Fixes: 2f258b74d1 ("b43: N-PHY: implement restoring general configuration")
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
Second set of patches for v5.12. Last time there was a smaller pull
request so unsurprisingly this time we have a big one. mt76 has new
hardware support and lots of new features, iwlwifi getting new
features and rtw88 got NAPI support. And the usual cleanups and fixes
all over.
Major changes:
ath10k
* support setting SAR limits via nl80211
rtw88
* support 8821 RFE type2 devices
* NAPI support
iwlwifi
* add new FW API support
* support for new So devices
* support for RF interference mitigation (RFI)
* support for PNVM (Platform Non-Volatile Memory, a firmware data
file) from BIOS
mt76
* add new mt7921e driver
* 802.11 encap offload support
* support for multiple pcie gen1 host interfaces on 7915
* 7915 testmode support
* 7915 txbf support
brcmfmac
* support for CQM RSSI notifications
wil6210
* support for extended DMG MCS 12.1 rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi to reduce overhead on rx interrupts.
Driver used to interrupt kernel for every Rx packet, this could
affect both system and network performance. NAPI is a mechanism that
uses polling when processing huge amount of traffic, by doing this
the number of interrupts can be decreased.
Network performance can also benefit from this patch. Since TCP
connection is bidirectional and acks are required for every several
packets. These ack packets occupie the PCI bus bandwidth and could
lead to performance degradation.
When napi is used, GRO receive is enabled by default in the mac80211
stack. So mac80211 won't pass every RX TCP packets to the kernel TCP
network stack immediately. Instead an aggregated large length TCP packet
will be delivered.
This reduces the tx acks sent and gains rx performance. After the patch,
the Rx throughput increases about 25Mbps in 11ac.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-4-pkshih@realtek.com
Second set of iwlwifi patches intended for v5.12
* Add some device IDs that got lost in a rebase;
* A bunch of fixes in the PPAG code;
* A few fixes in the debugging framework;
* Fix a couple of potential crashes in error paths;
* More HW IDs for new HW;
* Add one more value to the device configuration code;
* Support new scan config FW API;
* Some more CSA fixes;
* Support for RF interference mitigation (RFI);
* Improvements in the NVM flows;
* Bump the FW API support version;
* Implement support for PNVM from BIOS;
* Fix PM status when a FW crash happens;
* Some other small fixes, clean-ups and improvements.
# gpg: Signature made Thu 11 Feb 2021 02:02:34 AM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
I have received feedback that QCA6390 PCI support is working for many, and I'm
also using QCA6390 on my daily driver^Hlaptop. While there are issues still
to be resolved it's not really experimental anymore, so remove the experimental
warning from driver initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613040697-20289-1-git-send-email-kvalo@codeaurora.org
ieee80211_report_used_skb of mac80211 use the frame_control of
ieee80211_hdr in sk_buff and indicate it to another function
ieee80211_mgd_conn_tx_status, then it queue work ieee80211_sta_work,
but ieee80211_is_auth(fc) in ieee80211_sta_work check fail when the
authentication has transmitted by ath10k.
When the ath10k report it with HTT_TX_COMPL_STATE_DISCARD, it will be
set without flag IEEE80211_TX_STAT_ACK, then mac80211 should try the
next authentication immeditely, but in fact mac80211 wait 1 second for
it, the reason is ieee80211_is_auth(fc) in ieee80211_sta_work check
fail for the sk_buff which is not restored, the data of sk_buff is not
the begin of ieee80211_hdr, in fact it is the begin of htt_cmd_hdr.
dmesg without this patch, it wait 1 second for the next retry when
ath10k report without IEEE80211_TX_STAT_ACK for authentication:
[ 6973.883116] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 1/3)
[ 6974.705471] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 2/3)
[ 6975.712962] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 3/3)
Restore the sk_buff make mac8011 retry the next authentication
immeditely which meet logic of mac80211.
dmesg with this patch, it retry the next immeditely when ath10k
report without IEEE80211_TX_STAT_ACK for authentication:
[ 216.734813] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 1/3)
[ 216.739914] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 2/3)
[ 216.745874] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 3/3)
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612839530-2263-1-git-send-email-wgong@codeaurora.org
ac_classify() expects a struct sk_buff* as its second argument, which is
a member of struct tx_complete_data. priv happens to be a pointer to
struct tx_complete_data, so passing it directly to ac_classify() leads
to wrong behaviour and occasional panics.
Since there is only one caller of wilc_wlan_txq_add_net_pkt and it
already knows the type behind this pointer, and the structure is already
in the header file, change the function signature to use the real type
instead of void* in order to prevent confusion.
Signed-off-by: Vsevolod Kozlov <zaba@mm.st>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YCQomJ1mO5BLxYOT@Vsevolods-Mini.lan
Currently, for all devices and families, failing getting the temp
from the fw is indicated in the log as ERR.
This is too severe for two reasons:
1. The driver has a fall back - and schedules the next temp
read immediately after failing to read temp from the fw.
2. The temp read implementation in the fw is different between
HWs, and on older devices the flow is a-sync and may timeout.
Reducing the print severity from ERR to WARN will allow to
track the issue if it will appear many times, but not frighten users
if it appears once.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.dfd423b2b2ef.Icd576dc3e2e7174d3ed9c1c32f48ea0013699e72@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
